Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 20:57:22, Jun 27 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 20:57:30, Jun 27 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gc873063750 (Jun 27 2019 - 18:08:01 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 0 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1000 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:3f:90:5c DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - d6:15:34:f0:d1:b2 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - de:1d:1d:8a:5d:be , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 86:e0:48:96:e6:2f , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 8e:e8:61:ec:6a:23 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - b6:b3:9c:4c:83:2b , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - be:bb:b5:36:0f:27 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 22:0a:b8:e3:52:72 , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 4a:01:d6:d0:15:8d , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.14; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.14; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1224338/tftp-deploy-mp9jnf_4/kernel/uImage tftp 0x80080000 1224338/tftp-deploy-mp9jnf_4/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1224338/tftp-deploy-mp9jnf_4/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 3.7 MiB/s done Bytes transferred = 31853120 (1e60a40 hex) => tftp 0x91000000 1224338/tftp-deploy-mp9jnf_4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1224338/tftp-deploy-mp9jnf_4/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1224338/tftp-deploy-mp9jnf_4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################################### 2.6 MiB/s done Bytes transferred = 18897016 (1205878 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1224338/tftp-deploy-mp9jnf_4/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1224338/tftp-deploy-mp9jnf_4/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1224338/tftp-deploy-mp9jnf_4/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 2.9 KiB/s done Bytes transferred = 19637 (4cb5 hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-07-13 21:27:26 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 31853056 Bytes = 30.4 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-07-13 21:27:30 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18896952 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 0000000090007cb4 fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 5.10.179-cip32-rt12 (KernelCI@build-j1526344-arm64-gcc-10-defconfig-6zvrt) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Thu May 18 10:55:25 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3f8b00-0x837e3fafff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] On node 0 totalpages: 3653120 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 507392 pages, LIFO batch:63 [ 0.000000] Normal zone: 49152 pages used for memmap [ 0.000000] Normal zone: 3145728 pages, LIFO batch:63 [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 19 pages/cpu s40408 r8192 d29224 u77824 [ 0.000000] pcpu-alloc: s40408 r8192 d29224 u77824 alloc=19*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) [ 0.000000] Memory: 14180352K/14612480K available (14528K kernel code, 2882K rwdata, 7628K rodata, 5952K init, 502K bss, 399360K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080050000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080060000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080070000 [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000000] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008279] Console: colour dummy device 80x25 [ 0.012786] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023209] pid_max: default: 32768 minimum: 301 [ 0.027884] LSM: Security Framework initializing [ 0.032593] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.040258] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.048978] rcu: Hierarchical SRCU implementation. [ 0.053902] Platform MSI: gic-its@6020000 domain created [ 0.059290] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.066854] fsl-mc MSI: gic-its@6020000 domain created [ 0.072477] EFI services will not be available. [ 0.077206] smp: Bringing up secondary CPUs ... [ 0.081984] Detected PIPT I-cache on CPU1 [ 0.086024] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.092946] GICv3: CPU1: using allocated LPI pending table @0x0000008080080000 [ 0.100223] arch_timer: CPU1: Trapping CNTVCT access [ 0.105217] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.112041] Detected PIPT I-cache on CPU2 [ 0.116083] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.123175] GICv3: CPU2: using allocated LPI pending table @0x0000008080090000 [ 0.130446] arch_timer: CPU2: Trapping CNTVCT access [ 0.135438] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.142263] Detected PIPT I-cache on CPU3 [ 0.146295] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.153389] GICv3: CPU3: using allocated LPI pending table @0x00000080800a0000 [ 0.160655] arch_timer: CPU3: Trapping CNTVCT access [ 0.165647] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.172457] Detected PIPT I-cache on CPU4 [ 0.176498] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.183587] GICv3: CPU4: using allocated LPI pending table @0x00000080800b0000 [ 0.190858] arch_timer: CPU4: Trapping CNTVCT access [ 0.195850] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.202674] Detected PIPT I-cache on CPU5 [ 0.206707] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.213797] GICv3: CPU5: using allocated LPI pending table @0x00000080800c0000 [ 0.221063] arch_timer: CPU5: Trapping CNTVCT access [ 0.226054] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.232868] Detected PIPT I-cache on CPU6 [ 0.236912] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.244006] GICv3: CPU6: using allocated LPI pending table @0x00000080800d0000 [ 0.251280] arch_timer: CPU6: Trapping CNTVCT access [ 0.256274] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.263098] Detected PIPT I-cache on CPU7 [ 0.267133] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.274229] GICv3: CPU7: using allocated LPI pending table @0x00000080800e0000 [ 0.281499] arch_timer: CPU7: Trapping CNTVCT access [ 0.286492] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.293100] smp: Brought up 1 node, 8 CPUs [ 0.297228] SMP: Total of 8 processors activated. [ 0.301960] CPU features: detected: 32-bit EL0 Support [ 0.307132] CPU features: detected: CRC32 instructions [ 0.312301] CPU features: detected: 32-bit EL1 Support [ 0.329011] CPU: All CPU(s) started at EL2 [ 0.333158] alternatives: patching kernel code [ 0.338310] devtmpfs: initialized [ 0.342957] KASLR enabled [ 0.345659] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.355474] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.362947] pinctrl core: initialized pinctrl subsystem [ 0.368629] DMI not present or invalid. [ 0.372770] NET: Registered protocol family 16 [ 0.377925] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.385409] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.393744] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.401817] audit: initializing netlink subsys (disabled) [ 0.407333] audit: type=2000 audit(0.336:1): state=initialized audit_enabled=0 res=1 [ 0.407667] thermal_sys: Registered thermal governor 'step_wise' [ 0.407669] thermal_sys: Registered thermal governor 'power_allocator' [ 0.415128] cpuidle: using governor menu [ 0.431745] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.438655] ASID allocator initialised with 32768 entries [ 0.444548] Serial: AMBA PL011 UART driver [ 0.455720] Machine: Freescale Layerscape 2088A RDB Board [ 0.461155] SoC family: QorIQ LS2088A [ 0.464832] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.477344] HugeTLB registered 2.00 MiB page size, pre-allocated 256 pages [ 0.484286] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.491031] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.497791] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.505163] cryptd: max_cpu_qlen set to 1000 [ 0.510539] ACPI: Interpreter disabled. [ 0.515045] iommu: Default domain type: Translated [ 0.520017] vgaarb: loaded [ 0.522846] SCSI subsystem initialized [ 0.526672] libata version 3.00 loaded. [ 0.530606] usbcore: registered new interface driver usbfs [ 0.536145] usbcore: registered new interface driver hub [ 0.541501] usbcore: registered new device driver usb [ 0.546777] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.554158] i2c i2c-0: IMX I2C adapter registered [ 0.559030] pps_core: LinuxPPS API ver. 1 registered [ 0.564023] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.573232] PTP clock support registered [ 0.577215] EDAC MC: Ver: 3.0.0 [ 0.580852] fsl-ifc 2240000.ifc: Freescale Integrated Flash Controller [ 0.587434] fsl-ifc 2240000.ifc: IFC version 2.0, 8 banks [ 0.592943] FPGA manager framework [ 0.596382] Advanced Linux Sound Architecture Driver Initialized. [ 0.602829] clocksource: Switched to clocksource arch_sys_counter [ 0.609039] VFS: Disk quotas dquot_6.6.0 [ 0.613005] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.619998] pnp: PnP ACPI: disabled [ 0.625956] NET: Registered protocol family 2 [ 0.630756] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.641817] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.650606] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.659205] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.667106] TCP: Hash tables configured (established 131072 bind 65536) [ 0.673857] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.680869] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.688389] NET: Registered protocol family 1 [ 0.692955] RPC: Registered named UNIX socket transport module. [ 0.698914] RPC: Registered udp transport module. [ 0.703644] RPC: Registered tcp transport module. [ 0.708373] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.714853] PCI: CLS 0 bytes, default 64 [ 0.718864] Unpacking initramfs... [ 1.177760] Freeing initrd memory: 18448K [ 1.182230] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.190171] kvm [1]: IPA Size Limit: 44 bits [ 1.194976] kvm [1]: vgic-v2@c0e0000 [ 1.198583] kvm [1]: GIC system register CPU interface enabled [ 1.204549] kvm [1]: vgic interrupt IRQ9 [ 1.208601] kvm [1]: Hyp mode initialized successfully [ 1.215623] Initialise system trusted keyrings [ 1.220162] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 1.228935] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.235059] NFS: Registering the id_resolver key type [ 1.240156] Key type id_resolver registered [ 1.244366] Key type id_legacy registered [ 1.248426] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.255170] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.262662] 9p: Installing v9fs 9p2000 file system support [ 1.289099] Key type asymmetric registered [ 1.293220] Asymmetric key parser 'x509' registered [ 1.298137] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.305580] io scheduler mq-deadline registered [ 1.310137] io scheduler kyber registered [ 1.317817] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 1.325195] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 1.333785] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 1.342442] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 1.349188] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.354706] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.360929] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.371539] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 1.377589] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 1.383898] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 1.390207] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 1.397333] pci 0000:00:00.0: supports D1 D2 [ 1.401629] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 1.408314] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 1.414422] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 1.421115] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 1.427806] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 1.433446] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 1.440209] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 1.447560] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.463311] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 1.470499] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 1.477685] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 1.485304] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 1.492574] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.498795] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 1.505989] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 1.513606] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 1.520801] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 1.527990] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 1.534138] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.539394] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.545529] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 1.552867] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 1.560240] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 1.568833] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 1.577478] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 1.584224] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.589746] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 1.598762] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.609371] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 1.615425] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 1.622544] pci 0001:00:00.0: supports D1 D2 [ 1.626837] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 1.633846] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 1.641466] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 1.647230] EINJ: ACPI disabled. [ 1.655877] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.663120] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 16, base_baud = 21875000) is a 16550A [ 1.672185] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 16, base_baud = 21875000) is a 16550A [ 1.681083] printk: console [ttyS1] enabled [ 1.681083] printk: console [ttyS1] enabled [ 1.689467] printk: bootconsole [uart8250] disabled [ 1.689467] printk: bootconsole [uart8250] disabled [ 1.699459] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 17, base_baud = 21875000) is a 16550A [ 1.708454] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 17, base_baud = 21875000) is a 16550A [ 1.717444] SuperH (H)SCI(F) driver initialized [ 1.722175] msm_serial: driver initialized [ 1.727048] arm-smmu 5000000.iommu: probing hardware configuration... [ 1.733489] arm-smmu 5000000.iommu: SMMUv2 with: [ 1.738103] arm-smmu 5000000.iommu: stage 1 translation [ 1.743410] arm-smmu 5000000.iommu: stage 2 translation [ 1.748716] arm-smmu 5000000.iommu: nested translation [ 1.753935] arm-smmu 5000000.iommu: coherent table walk [ 1.759243] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 1.766376] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 1.772905] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 1.779342] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.785779] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.796236] loop: module loaded [ 1.799739] megasas: 07.714.04.00-rc1 [ 1.803863] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 1.811393] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 1.818813] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 1.826520] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.835483] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.845671] scsi host0: ahci-qoriq [ 1.849175] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 104 [ 1.857237] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 1.864763] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 1.872173] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 1.879870] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.888829] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.898746] scsi host1: ahci-qoriq [ 1.902208] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 105 [ 1.910491] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 1.919762] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 1.929851] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.934995] Amd/Fujitsu Extended Query version 1.5. [ 1.940044] number of CFI chips: 1 [ 1.959793] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 1.966152] nand: Micron MT29F16G08ABABAWP [ 1.970245] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 1.979032] Bad block table found at page 524160, version 0x01 [ 1.986780] Bad block table found at page 524032, version 0x01 [ 2.007253] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 2.015254] spi-nor spi0.0: unrecognized JEDEC id bytes: c7 8f 0e 1c 3c 78 [ 2.022459] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 2.029349] spi-nor: probe of spi1.0 failed with error -2 [ 2.035846] tun: Universal TUN/TAP device driver, 1.6 [ 2.041179] thunder_xcv, ver 1.0 [ 2.044423] thunder_bgx, ver 1.0 [ 2.047664] nicpf, ver 1.0 [ 2.050820] hclge is initializing [ 2.054145] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 2.061370] hns3: Copyright (c) 2017 Huawei Corporation. [ 2.066694] e1000: Intel(R) PRO/1000 Network Driver [ 2.071567] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 2.077323] e1000e: Intel(R) PRO/1000 Network Driver [ 2.082283] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.088276] e1000e 0000:01:00.0: Adding to iommu group 0 [ 2.093947] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.151279] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.168987] ata1: SATA link down (SStatus 0 SControl 300) [ 2.212764] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:3f:90:5c [ 2.220689] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.224992] ata2: SATA link down (SStatus 0 SControl 300) [ 2.227574] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 2.239677] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.245071] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.250655] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 2.256917] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 2.262995] sky2: driver version 1.30 [ 2.267061] VFIO - User Level meta-driver version: 0.3 [ 2.273412] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.279958] ehci-pci: EHCI PCI platform driver [ 2.284410] ehci-platform: EHCI generic platform driver [ 2.289677] ehci-orion: EHCI orion driver [ 2.293716] ehci-exynos: EHCI Exynos driver [ 2.297929] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.304111] ohci-pci: OHCI PCI platform driver [ 2.308563] ohci-platform: OHCI generic platform driver [ 2.313824] ohci-exynos: OHCI Exynos driver [ 2.318169] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.323659] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 2.331396] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.340810] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x03100000 [ 2.346886] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.352371] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 2.360026] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 2.366753] hub 1-0:1.0: USB hub found [ 2.370508] hub 1-0:1.0: 1 port detected [ 2.374547] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.382793] hub 2-0:1.0: USB hub found [ 2.386547] hub 2-0:1.0: 1 port detected [ 2.390601] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.396092] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 2.403817] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.413224] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x03110000 [ 2.419295] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.424779] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 2.432436] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 2.439124] hub 3-0:1.0: USB hub found [ 2.442879] hub 3-0:1.0: 1 port detected [ 2.446907] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.455151] hub 4-0:1.0: USB hub found [ 2.458908] hub 4-0:1.0: 1 port detected [ 2.463036] usbcore: registered new interface driver usb-storage [ 2.470035] i2c /dev entries driver [ 2.474713] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.480629] rtc-ds3232 2-0068: oscillator discontinuity flagged, time unreliable [ 2.489591] hwmon hwmon0: temp1_input not attached to any thermal zone [ 2.501722] rtc-ds3232 2-0068: registered as rtc0 [ 2.507599] rtc-ds3232 2-0068: setting system clock to 2022-09-26T09:46:40 UTC (1664185600) [ 2.516019] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.520943] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.525859] i2c i2c-0: Added multiplexed i2c bus 4 [ 2.530718] i2c i2c-0: Added multiplexed i2c bus 5 [ 2.535572] i2c i2c-0: Added multiplexed i2c bus 6 [ 2.540429] i2c i2c-0: Added multiplexed i2c bus 7 [ 2.545319] i2c i2c-0: Added multiplexed i2c bus 8 [ 2.550110] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 2.558512] sp805-wdt c000000.wdt: registration successful [ 2.564087] sp805-wdt c010000.wdt: registration successful [ 2.569645] sp805-wdt c100000.wdt: registration successful [ 2.575213] sp805-wdt c110000.wdt: registration successful [ 2.580765] sp805-wdt c200000.wdt: registration successful [ 2.586323] sp805-wdt c210000.wdt: registration successful [ 2.591920] sp805-wdt c300000.wdt: registration successful [ 2.597476] sp805-wdt c310000.wdt: registration successful [ 2.604324] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 2.612832] sdhci: Secure Digital Host Controller Interface driver [ 2.619023] sdhci: Copyright(c) Pierre Ossman [ 2.623576] Synopsys Designware Multimedia Card Interface Driver [ 2.629943] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.636433] ledtrig-cpu: registered to indicate activity on CPUs [ 2.643082] usbcore: registered new interface driver usbhid [ 2.648657] usbhid: USB HID core driver [ 2.653676] optee: probing for conduit method. [ 2.658131] optee: api uid mismatch [ 2.661621] optee: probe of firmware:optee failed with error -22 [ 2.661708] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 2.668260] NET: Registered protocol family 17 [ 2.679967] 9pnet: Installing 9P2000 support [ 2.684314] Key type dns_resolver registered [ 2.688756] printk: console [ttyS1]: printing thread started [ 2.688782] registered taskstats version 1 [ 2.688785] Loading compiled-in X.509 certificates [ 2.690406] pcieport 0000:00:00.0: Adding to iommu group 1 [ 2.690578] pcieport 0000:00:00.0: PME: Signaling with IRQ 112 [ 2.690682] pcieport 0001:00:00.0: Adding to iommu group 2 [ 2.690857] pcieport 0001:00:00.0: PME: Signaling with IRQ 116 [ 5.295836] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 5.322854] Sending DHCP requests .., OK [ 9.018872] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.190 [ 9.018882] IP-Config: Complete: [ 9.018884] device=eth0, hwaddr=68:05:ca:3f:90:5c, ipaddr=172.16.1.190, mask=255.255.255.0, gw=172.16.1.4 [ 9.018892] host=172.16.1.190, domain=example.org, nis-domain=(none) [ 9.018896] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 9.018901] nameserver0=172.16.1.4 [ 9.019092] ALSA device list: [ 9.019098] No soundcards found. [ 9.021572] Freeing unused kernel memory: 5952K [ 9.086933] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 9.123830] udevd[187]: starting version 3.2.9 [ 9.124123] random: udevd: uninitialized urandom read (16 bytes read) [ 9.124194] random: udevd: uninitialized urandom read (16 bytes read) [ 9.124215] random: udevd: uninitialized urandom read (16 bytes read) [ 9.126190] udevd[187]: specified user 'tss' unknown [ 9.126224] udevd[187]: specified group 'tss' unknown [ 9.126918] udevd[188]: starting eudev-3.2.9 [ 9.235913] lm90 4-004c: supply vcc not found, using dummy regulator [ 9.236449] ina2xx 3-0040: error configuring the device: -6 [ 9.239816] udevd[208]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 9.239835] udevd[208]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 9.246950] hwmon hwmon7: temp1_input not attached to any thermal zone done[ 9.246965] hwmon hwmon7: temp2_input not attached to any thermal zone Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK [ 9.320797] NET: Registered protocol family 10 [ 9.321595] Segment Routing with IPv6 /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1224338/environment . /lava-1224338/environment / # /lava-1224338/bin/lava-test-runner /lava-1224338/0 /lava-1224338/bin/lava-test-runner /lava-1224338/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1224338/[ 9.833238] 0/tests/0_dmesg[ 9.842584] + cat uuid + UUID=1224338_1.5.2.4.1 + set +x[ 9.854264] + KERNELCI_LAVA[ 9.862858] =y /bin/sh /opt/[ 9.873795] kernelci/dmesg.sh + set +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1224338/environment / # . /lava-1224338/environment/lava-1224338/bin/lava-test-runner /lava-1224338/1 / # /lava-1224338/bin/lava-test-runner /lava-1224338/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1224338/1/tests/1_bootr[ 10.311260] r + cat uuid + UUID=1224338_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1224338/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 8000000.crypto /lava-1224338/1/../bin/lava-test-case [ 11.328661] /lava-1224338/1/../bin/lava-test-case [ 11.341545] /lava-1224338/1/../bin/lava-test-case [ 11.354342] + set +x [ 11.361816] / #