[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.191 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10402818/tftp-deploy-5y68mk4l/kernel/zImage tftp 0x10000000 10402818/tftp-deploy-5y68mk4l/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '10402818/tftp-deploy-5y68mk4l/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.1 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 10402818/tftp-deploy-5y68mk4l/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10402818/tftp-deploy-5y68mk4l/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '10402818/tftp-deploy-5y68mk4l/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 4.1 MiB/s done Bytes transferred = 16067159 (f52a57 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10402818/tftp-deploy-5y68mk4l/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10402818/tftp-deploy-5y68mk4l/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '10402818/tftp-deploy-5y68mk4l/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16067095 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.180-cip33 (KernelCI@build-j1537657-arm-gcc-10-multi-v7-defconfig-xnt5z) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun May 21 08:43:47 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932668K/1048576K available (14336K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 50372K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008095] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021769] Console: colour dummy device 80x30 <6>[ 0.023658] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034333] pid_max: default: 32768 minimum: 301 <6>[ 0.039369] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046788] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055403] CPU: Testing write buffer coherency: ok <6>[ 0.059915] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065450] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071845] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079502] rcu: Hierarchical SRCU implementation. <6>[ 0.086483] EFI services will not be available. <6>[ 0.088718] smp: Bringing up secondary CPUs ... <6>[ 0.094008] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094017] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105353] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105360] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116554] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116561] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127001] smp: Brought up 1 node, 4 CPUs <6>[ 0.131226] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.137770] CPU: All CPU(s) started in SVC mode. <6>[ 0.143197] devtmpfs: initialized <6>[ 0.153761] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159105] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168975] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179179] pinctrl core: initialized pinctrl subsystem <6>[ 0.183648] DMI not present or invalid. <6>[ 0.186770] NET: Registered protocol family 16 <6>[ 0.194090] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200732] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200918] cpuidle: using governor menu <6>[ 0.209004] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.387375] vdd1p1: supplied by regulator-dummy <6>[ 0.396476] vdd3p0: supplied by regulator-dummy <6>[ 0.405481] vdd2p5: supplied by regulator-dummy <6>[ 0.414540] vddarm: supplied by regulator-dummy <6>[ 0.423719] vddpu: supplied by regulator-dummy <6>[ 0.432530] vddsoc: supplied by regulator-dummy <6>[ 0.759547] No ATAGs? <6>[ 0.759732] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.767510] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.777783] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.788213] Serial: AMBA PL011 UART driver <6>[ 0.792404] printk: console [ramoops-1] enabled <6>[ 0.794710] pstore: Registered ramoops as persistent store backend <6>[ 0.800976] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.838934] iommu: Default domain type: Translated <6>[ 0.841641] vgaarb: loaded <5>[ 0.845093] SCSI subsystem initialized <6>[ 0.848843] usbcore: registered new interface driver usbfs <6>[ 0.853979] usbcore: registered new interface driver hub <6>[ 0.859559] usbcore: registered new device driver usb <6>[ 0.866377] i2c i2c-0: IMX I2C adapter registered <6>[ 0.871121] i2c i2c-1: IMX I2C adapter registered <6>[ 0.875539] i2c i2c-2: IMX I2C adapter registered <6>[ 0.881068] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.884900] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.894333] PTP clock support registered <6>[ 0.902083] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.972449] NET: Registered protocol family 2 <6>[ 1.974641] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.983066] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.990522] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.998607] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.006051] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.012734] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.019408] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.026895] NET: Registered protocol family 1 <6>[ 2.031901] RPC: Registered named UNIX socket transport module. <6>[ 2.037504] RPC: Registered udp transport module. <6>[ 2.042450] RPC: Registered tcp transport module. <6>[ 2.047391] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.054110] PCI: CLS 0 bytes, default 64 <6>[ 2.058776] Trying to unpack rootfs image as initramfs... <6>[ 3.416662] Freeing initrd memory: 15692K <4>[ 3.418610] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.425904] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.435719] Initialise system trusted keyrings <6>[ 3.438821] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.451306] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.455310] NFS: Registering the id_resolver key type <5>[ 3.459905] Key type id_resolver registered <5>[ 3.464323] Key type id_legacy registered <6>[ 3.468659] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.475537] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.483232] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.488278] Key type asymmetric registered <5>[ 3.492163] Asymmetric key parser 'x509' registered <6>[ 3.497312] bounce: pool size: 64 pages <6>[ 3.501394] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.509034] io scheduler mq-deadline registered <6>[ 3.513813] io scheduler kyber registered <6>[ 3.558498] mxs-dma 110000.dma-apbh: initialized <4>[ 3.565376] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.572316] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.636559] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.644842] SuperH (H)SCI(F) driver initialized <6>[ 3.647775] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.656696] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.664597] printk: console [ttymxc1] enabled <6>[ 3.664597] printk: console [ttymxc1] enabled <6>[ 3.673763] printk: bootconsole [ec_imx21] disabled <6>[ 3.673763] printk: bootconsole [ec_imx21] disabled <6>[ 3.685428] msm_serial: driver initialized <6>[ 3.691467] STMicroelectronics ASC driver initialized <6>[ 3.698797] STM32 USART driver initialized <4>[ 3.714404] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.722325] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.729080] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.745822] brd: module loaded <6>[ 3.759200] loop: module loaded <6>[ 3.766596] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.774826] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.783131] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.791578] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.799594] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.807347] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.814926] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.825557] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.832840] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.841901] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.852718] scsi host0: ahci-imx <6>[ 3.856587] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.877345] CAN device driver interface <6>[ 3.882854] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.892395] pps pps0: new PPS source ptp0 <6>[ 3.929158] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.936778] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.942014] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.948284] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.953968] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.966072] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.973797] usbcore: registered new interface driver pegasus <6>[ 3.979772] usbcore: registered new interface driver asix <6>[ 3.985487] usbcore: registered new interface driver ax88179_178a <6>[ 3.991881] usbcore: registered new interface driver cdc_ether <6>[ 3.998042] usbcore: registered new interface driver smsc75xx <6>[ 4.004124] usbcore: registered new interface driver smsc95xx <6>[ 4.010167] usbcore: registered new interface driver net1080 <6>[ 4.016144] usbcore: registered new interface driver cdc_subset <6>[ 4.022386] usbcore: registered new interface driver zaurus <6>[ 4.028296] usbcore: registered new interface driver cdc_ncm <6>[ 4.037869] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.044688] ehci-pci: EHCI PCI platform driver <6>[ 4.049437] ehci-platform: EHCI generic platform driver <6>[ 4.055261] ehci-orion: EHCI orion driver <6>[ 4.059761] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.064255] ehci-st: EHCI STMicroelectronics driver <6>[ 4.069581] ehci-exynos: EHCI Exynos driver <6>[ 4.074236] ehci-atmel: EHCI Atmel driver <6>[ 4.078690] tegra-ehci: Tegra EHCI driver <6>[ 4.083205] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.089669] ohci-pci: OHCI PCI platform driver <6>[ 4.094440] ohci-platform: OHCI generic platform driver <6>[ 4.100212] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.104708] ohci-st: OHCI STMicroelectronics driver <6>[ 4.110051] ohci-atmel: OHCI Atmel driver <6>[ 4.115440] usbcore: registered new interface driver usb-storage <6>[ 4.130010] i2c /dev entries driver <6>[ 4.153576] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.160029] sdhci: Copyright(c) Pierre Ossman <6>[ 4.167405] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.175664] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.184075] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.187072] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.189358] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.200021] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.206490] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.207423] usbcore: registered new interface driver usbhid <6>[ 4.212231] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.218037] usbhid: USB HID core driver <6>[ 4.224586] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.235370] NET: Registered protocol family 10 <6>[ 4.236452] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.248505] Segment Routing with IPv6 <6>[ 4.252541] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.259291] NET: Registered protocol family 17 <6>[ 4.264061] can: controller area network core <6>[ 4.268759] NET: Registered protocol family 29 <6>[ 4.273494] can: raw protocol <6>[ 4.276736] can: broadcast manager protocol <6>[ 4.276874] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.281193] can: netlink gateway - max_hops=1 <5>[ 4.293399] Key type dns_resolver registered <6>[ 4.299689] ThumbEE CPU extension supported. <5>[ 4.304280] Registering SWP/SWPB emulation handler <5>[ 4.309665] Loading compiled-in X.509 certificates <6>[ 4.320067] pstore: Using crash dump compression: deflate <6>[ 4.323955] mmc2: new high speed SDHC card at address 0001 <6>[ 4.332910] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 4.350929] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.358905] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.367204] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.381684] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.384819] imx_usb 2184200.usb: No over current polarity defined <4>[ 4.389422] GPT:7812499 != 30560255 <6>[ 4.399391] ci_hdrc ci_hdrc.1: EHCI Host Controller <4>[ 4.399489] GPT:Alternate GPT header not at the end of the disk. <6>[ 4.404705] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 4.410914] GPT:7812499 != 30560255 <4>[ 4.421983] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.427450] mmcblk2: p1 p2 p3 <6>[ 4.452137] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.459182] hub 1-0:1.0: USB hub found <6>[ 4.463330] hub 1-0:1.0: 1 port detected <3>[ 4.471576] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 4.479225] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 4.487627] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 4.499903] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.507863] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.516074] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.529173] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.537117] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.545318] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.555684] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.568684] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.576649] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.584951] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.598754] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 4.812147] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 5.013746] hub 1-1:1.0: USB hub found <6>[ 5.017970] hub 1-1:1.0: 3 ports detected <4>[ 5.032661] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.040710] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.050595] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.722628] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.742180] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.772127] Sending DHCP requests ., OK <6>[ 6.816319] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.191 <6>[ 6.824740] IP-Config: Complete: <6>[ 6.828261] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.191, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.839112] host=192.168.201.191, domain=lava-rack, nis-domain=(none) <6>[ 6.846308] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.846320] nameserver0=192.168.201.1 <6>[ 6.865364] Freeing unused kernel memory: 2048K <6>[ 6.892981] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.050170] udevd[135]: starting version 3.2.9 <5>[ 7.056007] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.063130] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.069954] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.085483] udevd[135]: specified user 'tss' unknown <27>[ 7.090939] udevd[135]: specified group 'tss' unknown <30>[ 7.099123] udevd[136]: starting eudev-3.2.9 <6>[ 7.484154] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.534885] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.546177] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.554183] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.565440] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.604751] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.612780] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.614668] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.627895] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.636552] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.645320] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.684390] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.832852] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.862333] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.873169] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.902979] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.909794] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.939289] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.000051] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.005517] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.012431] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.022800] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.032590] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.038969] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.062504] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.111528] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.120115] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.128683] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.137216] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.184587] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.192566] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.215349] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.258507] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.266717] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.275402] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.283640] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.285538] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.300717] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.309396] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.318010] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.344971] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.353093] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.355657] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.361901] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.374572] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.404626] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.413266] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.421896] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.430491] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.455334] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.468817] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.504175] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.551787] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.560427] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.569059] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.577650] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.657289] caam algorithms registered in /proc/crypto <6>[ 8.664437] caam 2100000.crypto: registering rng-caam <4>[ 8.671857] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.680003] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.689723] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.718567] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.727107] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.735711] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.744290] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.754693] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.762740] panel-simple panel-lcd: Specify missing connector_type <5>[ 8.852230] random: crng init done <5>[ 8.855931] random: 1 urandom warning(s) missed due to ratelimiting done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10402818/environment . /lava-10402818/environment / # /lava-10402818/bin/lava-test-runner /lava-10402818/0 /lava-10402818/bin/lava-test-runner /lava-10402818/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-10402818/0/tests/0_dmesg + cat uuid + UUID=10402818_1.5.2.4.1<8>[ 9.641819] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.697010] <8>[ 9.738335] <8>[ 9.779818] + set<8>[ 9.789771] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10402818/environment / # . /lava-10402818/environment/lava-10402818/bin/lava-test-runner /lava-10402818/1 / # /lava-10402818/bin/lava-test-runner /lava-10402818/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10402818/1/tests/1_bootrr + cat uuid + UUID=10402818_1.5.2.4.5<8>[ 10.320266] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10402818/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds 120000.hdmi panel-lcd /lava-10402818/1/../bin/lava-test-case <8>[ 11.407942] /lava-10402818/1/../bin/lava-test-case <8>[ 11.466170] /lava-10402818/1/../bin/lava-test-case <8>[ 11.491279] + set<8>[ 11.510530] +x / #