[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.13 (11 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10724639/tftp-deploy-xa4g6eji/kernel/zImage tftp 0x10000000 10724639/tftp-deploy-xa4g6eji/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10724639/tftp-deploy-xa4g6eji/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 4.7 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 10724639/tftp-deploy-xa4g6eji/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10724639/tftp-deploy-xa4g6eji/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10724639/tftp-deploy-xa4g6eji/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 4.9 MiB/s done Bytes transferred = 12144480 (b94f60 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10724639/tftp-deploy-xa4g6eji/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10724639/tftp-deploy-xa4g6eji/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10724639/tftp-deploy-xa4g6eji/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.5 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10724639/extract-nfsrootfs-gfh23h6h,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10724639/extract-nfsrootfs-gfh23h6h,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12144416 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.182-cip35 (KernelCI@build-j35821-arm-gcc-10-multi-v7-defconfig-bfzhp) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Jun 14 12:14:03 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10724639/extract-nfsrootfs-gfh23h6h,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936500K/1048576K available (14336K kernel code, 2239K rwdata, 5360K rodata, 2048K init, 424K bss, 46540K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008095] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021858] Console: colour dummy device 80x30 <6>[ 0.023751] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034420] pid_max: default: 32768 minimum: 301 <6>[ 0.039456] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046874] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055486] CPU: Testing write buffer coherency: ok <6>[ 0.060003] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065549] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071936] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079624] rcu: Hierarchical SRCU implementation. <6>[ 0.086635] EFI services will not be available. <6>[ 0.088871] smp: Bringing up secondary CPUs ... <6>[ 0.094166] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094175] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105502] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105509] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116712] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116720] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127149] smp: Brought up 1 node, 4 CPUs <6>[ 0.131379] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.137924] CPU: All CPU(s) started in SVC mode. <6>[ 0.143349] devtmpfs: initialized <6>[ 0.153617] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158964] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168833] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179046] pinctrl core: initialized pinctrl subsystem <6>[ 0.183523] DMI not present or invalid. <6>[ 0.186631] NET: Registered protocol family 16 <6>[ 0.193894] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200534] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200727] cpuidle: using governor menu <6>[ 0.208825] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.388277] vdd1p1: supplied by regulator-dummy <6>[ 0.397414] vdd3p0: supplied by regulator-dummy <6>[ 0.406492] vdd2p5: supplied by regulator-dummy <6>[ 0.415572] vddarm: supplied by regulator-dummy <6>[ 0.424804] vddpu: supplied by regulator-dummy <6>[ 0.433641] vddsoc: supplied by regulator-dummy <6>[ 0.763943] No ATAGs? <6>[ 0.764133] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.771906] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.782121] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.792464] Serial: AMBA PL011 UART driver <6>[ 0.796702] printk: console [ramoops-1] enabled <6>[ 0.798963] pstore: Registered ramoops as persistent store backend <6>[ 0.805193] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.842980] iommu: Default domain type: Translated <6>[ 0.845741] vgaarb: loaded <5>[ 0.849105] SCSI subsystem initialized <6>[ 0.852829] usbcore: registered new interface driver usbfs <6>[ 0.858068] usbcore: registered new interface driver hub <6>[ 0.863579] usbcore: registered new device driver usb <6>[ 0.870408] i2c i2c-0: IMX I2C adapter registered <6>[ 0.875143] i2c i2c-1: IMX I2C adapter registered <6>[ 0.879622] i2c i2c-2: IMX I2C adapter registered <6>[ 0.885087] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.888967] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.898373] PTP clock support registered <6>[ 0.906181] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.967602] NET: Registered protocol family 2 <6>[ 1.969819] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.978232] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.985679] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.993752] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.001209] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.007891] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.014565] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.022055] NET: Registered protocol family 1 <6>[ 2.027080] RPC: Registered named UNIX socket transport module. <6>[ 2.032624] RPC: Registered udp transport module. <6>[ 2.037616] RPC: Registered tcp transport module. <6>[ 2.042545] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.049267] PCI: CLS 0 bytes, default 64 <6>[ 2.053939] Trying to unpack rootfs image as initramfs... <6>[ 3.015625] Freeing initrd memory: 11860K <4>[ 3.017692] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.024769] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.034686] Initialise system trusted keyrings <6>[ 3.037871] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.050058] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.054061] NFS: Registering the id_resolver key type <5>[ 3.058718] Key type id_resolver registered <5>[ 3.063050] Key type id_legacy registered <6>[ 3.067443] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.074275] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.081981] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.087046] Key type asymmetric registered <5>[ 3.090893] Asymmetric key parser 'x509' registered <6>[ 3.096067] bounce: pool size: 64 pages <6>[ 3.100170] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.107789] io scheduler mq-deadline registered <6>[ 3.112554] io scheduler kyber registered <6>[ 3.156659] mxs-dma 110000.dma-apbh: initialized <4>[ 3.163453] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.170389] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.220952] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.229184] SuperH (H)SCI(F) driver initialized <6>[ 3.232136] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.241021] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.248932] printk: console [ttymxc1] enabled <6>[ 3.248932] printk: console [ttymxc1] enabled <6>[ 3.258115] printk: bootconsole [ec_imx21] disabled <6>[ 3.258115] printk: bootconsole [ec_imx21] disabled <6>[ 3.269797] msm_serial: driver initialized <6>[ 3.275807] STMicroelectronics ASC driver initialized <6>[ 3.283192] STM32 USART driver initialized <4>[ 3.298694] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.306617] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.313427] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.330126] brd: module loaded <6>[ 3.343379] loop: module loaded <6>[ 3.350761] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.358976] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.367263] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.375709] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.383741] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.391502] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.399065] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.409654] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.416944] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.426004] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.436849] scsi host0: ahci-imx <6>[ 3.440711] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.461367] CAN device driver interface <6>[ 3.466868] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.476394] pps pps0: new PPS source ptp0 <6>[ 3.498560] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.506189] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.511424] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.517689] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.523356] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.535405] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.543143] usbcore: registered new interface driver pegasus <6>[ 3.549128] usbcore: registered new interface driver asix <6>[ 3.554829] usbcore: registered new interface driver ax88179_178a <6>[ 3.561240] usbcore: registered new interface driver cdc_ether <6>[ 3.567402] usbcore: registered new interface driver smsc75xx <6>[ 3.573456] usbcore: registered new interface driver smsc95xx <6>[ 3.579529] usbcore: registered new interface driver net1080 <6>[ 3.585496] usbcore: registered new interface driver cdc_subset <6>[ 3.591730] usbcore: registered new interface driver zaurus <6>[ 3.597651] usbcore: registered new interface driver cdc_ncm <6>[ 3.607234] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.614032] ehci-pci: EHCI PCI platform driver <6>[ 3.618810] ehci-platform: EHCI generic platform driver <6>[ 3.624594] ehci-orion: EHCI orion driver <6>[ 3.629127] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.633593] ehci-st: EHCI STMicroelectronics driver <6>[ 3.638943] ehci-exynos: EHCI Exynos driver <6>[ 3.643568] ehci-atmel: EHCI Atmel driver <6>[ 3.648040] tegra-ehci: Tegra EHCI driver <6>[ 3.652536] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.659017] ohci-pci: OHCI PCI platform driver <6>[ 3.663769] ohci-platform: OHCI generic platform driver <6>[ 3.669544] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.674026] ohci-st: OHCI STMicroelectronics driver <6>[ 3.679395] ohci-atmel: OHCI Atmel driver <6>[ 3.684931] usbcore: registered new interface driver usb-storage <6>[ 3.699509] i2c /dev entries driver <6>[ 3.723188] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.729667] sdhci: Copyright(c) Pierre Ossman <6>[ 3.737108] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.745352] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.752623] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.752828] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.757920] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.768608] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.775946] usbcore: registered new interface driver usbhid <6>[ 3.781816] usbhid: USB HID core driver <6>[ 3.792608] NET: Registered protocol family 10 <6>[ 3.794984] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.796456] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.796501] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.796508] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.798365] Segment Routing with IPv6 <6>[ 3.800017] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.835308] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.842109] NET: Registered protocol family 17 <6>[ 3.846858] can: controller area network core <6>[ 3.851563] NET: Registered protocol family 29 <6>[ 3.856298] can: raw protocol <6>[ 3.859539] can: broadcast manager protocol <6>[ 3.863997] can: netlink gateway - max_hops=1 <5>[ 3.869054] Key type dns_resolver registered <6>[ 3.875352] ThumbEE CPU extension supported. <5>[ 3.879937] Registering SWP/SWPB emulation handler <5>[ 3.885370] Loading compiled-in X.509 certificates <6>[ 3.895989] pstore: Using crash dump compression: deflate <4>[ 3.927465] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.935388] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.943715] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.961120] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.971159] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.976374] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.983965] mmc2: new high speed SDHC card at address 0001 <6>[ 3.990620] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 4.006172] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <4>[ 4.013574] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 4.013584] hub 1-0:1.0: USB hub found <6>[ 4.013668] hub 1-0:1.0: 1 port detected <4>[ 4.021338] GPT:29296874 != 30965759 <3>[ 4.029540] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 4.029558] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 4.029593] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 4.033437] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.045836] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.049404] GPT:29296874 != 30965759 <4>[ 4.049408] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.049460] mmcblk2: p1 p2 p3 <4>[ 4.057073] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.091885] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.105046] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.112968] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.121188] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.134240] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.142166] panel-simple panel-lcd: Specify missing connector_type <6>[ 4.151014] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.160645] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.174038] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.181994] panel-simple panel-lcd: Specify missing connector_type <6>[ 4.194181] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 4.406243] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.607819] hub 1-1:1.0: USB hub found <6>[ 4.612050] hub 1-1:1.0: 3 ports detected <4>[ 4.620166] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.638443] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.646549] panel-simple panel-lcd: Specify missing connector_type <6>[ 6.316682] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.336275] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.366251] Sending DHCP requests ., OK <6>[ 6.410420] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.13 <6>[ 6.418746] IP-Config: Complete: <6>[ 6.422269] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.201.13, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.433027] host=imx6q-sabrelite-lava-cbg-2, domain=lava-rack, nis-domain=(none) <6>[ 6.441178] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.441191] nameserver0=192.168.201.1 <6>[ 6.460152] Freeing unused kernel memory: 2048K <6>[ 6.497228] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 7.605289] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 7.620561] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.643097] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.657749] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.665768] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.677777] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.690337] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.699052] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 7.705033] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 7.707744] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 7.715525] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.723935] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.747163] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.778420] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.786503] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.809493] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.849483] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.857221] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.865090] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.871960] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.874012] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.944471] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.005231] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.010661] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.017560] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.027726] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.034116] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.040527] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.047808] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.071086] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.079677] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.088266] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.096827] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.134583] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.142661] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.151872] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.151879] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.152065] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.176651] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.184873] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.200184] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.208380] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.217057] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.225657] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.234239] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.245315] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.253788] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.263064] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.263741] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.280654] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.289260] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.297861] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.306456] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.349470] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.358479] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.369801] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.395195] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.403861] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.412462] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.421048] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.691356] caam algorithms registered in /proc/crypto <6>[ 8.698855] caam 2100000.crypto: registering rng-caam <4>[ 8.706169] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.714171] panel-simple panel-lcd: Specify missing connector_type Begin: Loading essential drivers ... done. <4>[ 8.733560] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done<6>[ 8.750429] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) . Begin: Running /scripts/nfs-pr<6>[ 8.761129] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) emount ... Waiting up to 60 secs <6>[ 8.772444] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) for any ethernet to become availa<6>[ 8.783650] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) ble Device /sys/class/net/eth0 found done. <5>[ 8.886635] random: crng init done IP-Config: eth0 hardware address 00:19:b8:00:e5:47 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.13 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-2 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 9.956569] systemd[1]: System time before build time, advancing clock. <30>[ 10.045703] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.070581] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.119262] systemd[1]: Set hostname to . <30>[ 11.090526] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.100281] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.113057] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.122781] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.157557] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.197538] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.237296] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.276998] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.316989] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.356752] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.369563] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.407056] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.436626] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.476550] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.506735] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.537601] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.620522] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.632244] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.667853] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.708906] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.750359] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 11.787784] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 11.827502] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.837098] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.852172] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 11.892350] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 11.934849] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 11.982409] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 12.019762] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 12.059737] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.100430] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.116422] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.154971] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.190263] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.230707] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.271985] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.317651] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.367663] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.441233] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 12.448342] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 12.486949] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 12.771877] systemd-journald[288]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Service. [ OK ] Found device /dev/ttymxc1. [ OK ] Started User Login Management. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Network Name Resolution... [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.182-cip35 #1 SMP Wed Jun 14 12:14:03 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10724639/extract-nfsrootfs-gfh23h6h' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10724639/extract-nfsrootfs-gfh23h6h' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-10724639/environment . /lava-10724639/environment / # /lava-10724639/bin/lava-test-runner /lava-10724639/0 /lava-10724639/bin/lava-test-runner /lava-10724639/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-10724639/0/tests/0_timesync-off ++ cat uuid + UUID=10724639_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-10724639/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=10724639_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.182-cip35-8-g2391124f19a70/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-06-14 12:32:44-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.182-cip35-8-g2391124f19a70/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1409156 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 44.98K 170KB/s kselftest.tar.xz 15%[==> ] 214.67K 404KB/s kselftest.tar.xz 58%[==========> ] 807.16K 965KB/s kselftest.tar.xz 100%[===================>] 1.34M 1.38MB/s in 1.0s 2023-06-14 12:32:46 (1.38 MB/s) - 'kselftest.tar.xz' saved [1409156/1409156] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== <12>[ 39.035518] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #