Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 22C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => setenv ipaddr 172.16.1.16; setenv serverip 172.16.1.4; setenv ethact FEC0; setenv ethprime FEC setenv ipaddr 172.16.1.16; setenv serverip 172.16.1.4; setenv ethact FEC0; setenv ethprime FEC => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp ${loadaddr} 1237590/tftp-deploy-homc_b76/kernel/zImage tftp ${loadaddr} 1237590/tftp-deploy-homc_b76/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1237590/tftp-deploy-homc_b76/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 1.6 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp ${initrd_addr} 1237590/tftp-deploy-homc_b76/ramdisk/ramdisk.cpio.gz.uboot tftp ${initrd_addr} 1237590/tftp-deploy-homc_b76/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1237590/tftp-deploy-homc_b76/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 10.1 MiB/s done Bytes transferred = 16084471 (f56df7 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp ${fdt_addr} 1237590/tftp-deploy-homc_b76/dtb/imx7d-sdb.dtb tftp ${fdt_addr} 1237590/tftp-deploy-homc_b76/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1237590/tftp-deploy-homc_b76/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 5.2 MiB/s done Bytes transferred = 37996 (946c hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz ${loadaddr} ${initrd_addr} ${fdt_addr} bootz ${loadaddr} ${initrd_addr} ${fdt_addr} Kernel image @ 0x80800000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 83800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16084407 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300c46b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.186-cip37 (KernelCI@build-j5461-arm-gcc-10-multi-v7-defconfig-t6nrs) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Jul 19 12:38:09 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932836K/1048576K available (14336K kernel code, 2239K rwdata, 5356K rodata, 2048K init, 424K bss, 50204K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000008] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008313] Switching to timer-based delay loop, resolution 125ns <6>[ 0.016010] Switching to timer-based delay loop, resolution 41ns <6>[ 0.021005] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029140] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.043606] Console: colour dummy device 80x30 <6>[ 0.045519] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.056162] pid_max: default: 32768 minimum: 301 <6>[ 0.061223] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.068680] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.077470] CPU: Testing write buffer coherency: ok <6>[ 0.082211] CPU0: update cpu_capacity 1024 <6>[ 0.086247] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.092980] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.100515] rcu: Hierarchical SRCU implementation. <6>[ 0.107664] EFI services will not be available. <6>[ 0.109856] smp: Bringing up secondary CPUs ... <6>[ 0.115152] smp: Brought up 1 node, 1 CPU <6>[ 0.118718] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.125235] CPU: All CPU(s) started in SVC mode. <6>[ 0.130658] devtmpfs: initialized <6>[ 0.142001] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.147425] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.157315] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.166820] pinctrl core: initialized pinctrl subsystem <6>[ 0.171896] DMI not present or invalid. <6>[ 0.175086] NET: Registered protocol family 16 <6>[ 0.180878] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.188677] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.188799] cpuidle: using governor menu <6>[ 0.196951] No ATAGs? <6>[ 0.199051] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.207314] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.216433] Serial: AMBA PL011 UART driver <6>[ 0.266899] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <6>[ 0.272677] imx7d-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.325455] iommu: Default domain type: Translated <6>[ 0.328740] vgaarb: loaded <5>[ 0.331764] SCSI subsystem initialized <6>[ 0.335504] usbcore: registered new interface driver usbfs <6>[ 0.340588] usbcore: registered new interface driver hub <6>[ 0.346243] usbcore: registered new device driver usb <6>[ 0.359656] i2c i2c-0: IMX I2C adapter registered <6>[ 0.367693] i2c i2c-1: IMX I2C adapter registered <6>[ 0.370391] i2c i2c-2: IMX I2C adapter registered <6>[ 0.380619] i2c i2c-3: IMX I2C adapter registered <6>[ 0.384116] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.388027] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.397472] PTP clock support registered <6>[ 0.405415] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.525627] NET: Registered protocol family 2 <6>[ 1.527692] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.536360] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.543802] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.551934] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.559416] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.566042] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.572878] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.580396] NET: Registered protocol family 1 <6>[ 1.585704] RPC: Registered named UNIX socket transport module. <6>[ 1.591025] RPC: Registered udp transport module. <6>[ 1.596051] RPC: Registered tcp transport module. <6>[ 1.600998] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.607767] PCI: CLS 0 bytes, default 64 <6>[ 1.612477] Trying to unpack rootfs image as initramfs... <6>[ 2.944114] Freeing initrd memory: 15708K <6>[ 2.946352] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 2.955805] Initialise system trusted keyrings <6>[ 2.959238] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.972764] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.976971] NFS: Registering the id_resolver key type <5>[ 2.981407] Key type id_resolver registered <5>[ 2.985862] Key type id_legacy registered <6>[ 2.990238] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.997139] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.004858] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.010011] Key type asymmetric registered <5>[ 3.013831] Asymmetric key parser 'x509' registered <6>[ 3.019078] bounce: pool size: 64 pages <6>[ 3.023143] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.030826] io scheduler mq-deadline registered <6>[ 3.035633] io scheduler kyber registered <4>[ 3.063302] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 3.081055] mxs-dma 33000000.dma-apbh: initialized <4>[ 3.096107] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <6>[ 3.103148] imx-sdma 30bd0000.sdma: external firmware not found, using ROM firmware <6>[ 3.166840] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.175249] SuperH (H)SCI(F) driver initialized <3>[ 3.178087] clk: failed to reparent uart1_src to pll_sys_main_240m_clk: -16 <6>[ 3.184717] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 58, base_baud = 1500000) is a IMX <6>[ 3.193666] printk: console [ttymxc0] enabled <6>[ 3.193666] printk: console [ttymxc0] enabled <6>[ 3.202806] printk: bootconsole [ec_imx6q0] disabled <6>[ 3.202806] printk: bootconsole [ec_imx6q0] disabled <6>[ 3.214308] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 67, base_baud = 15000000) is a IMX <6>[ 3.226672] msm_serial: driver initialized <6>[ 3.231279] STMicroelectronics ASC driver initialized <6>[ 3.238365] STM32 USART driver initialized <6>[ 3.262111] brd: module loaded <6>[ 3.273285] loop: module loaded <6>[ 3.292006] CAN device driver interface <6>[ 3.297423] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.308595] pps pps0: new PPS source ptp0 <3>[ 3.313774] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 3.320920] fec 30bf0000.ethernet: Using random MAC address: c6:d7:d4:11:a4:3f <6>[ 4.379752] fec 30bf0000.ethernet eth0: registered PHC device 0 <6>[ 4.387461] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.392701] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.399014] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.404678] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.416039] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.423754] usbcore: registered new interface driver pegasus <6>[ 4.429752] usbcore: registered new interface driver asix <6>[ 4.435474] usbcore: registered new interface driver ax88179_178a <6>[ 4.441878] usbcore: registered new interface driver cdc_ether <6>[ 4.448052] usbcore: registered new interface driver smsc75xx <6>[ 4.454112] usbcore: registered new interface driver smsc95xx <6>[ 4.460181] usbcore: registered new interface driver net1080 <6>[ 4.466160] usbcore: registered new interface driver cdc_subset <6>[ 4.472380] usbcore: registered new interface driver zaurus <6>[ 4.478323] usbcore: registered new interface driver cdc_ncm <6>[ 4.487505] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.494304] ehci-pci: EHCI PCI platform driver <6>[ 4.499087] ehci-platform: EHCI generic platform driver <6>[ 4.504829] ehci-orion: EHCI orion driver <6>[ 4.509334] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.513759] ehci-st: EHCI STMicroelectronics driver <6>[ 4.519071] ehci-exynos: EHCI Exynos driver <6>[ 4.523667] ehci-atmel: EHCI Atmel driver <6>[ 4.528107] tegra-ehci: Tegra EHCI driver <6>[ 4.532571] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.539060] ohci-pci: OHCI PCI platform driver <6>[ 4.543815] ohci-platform: OHCI generic platform driver <6>[ 4.549557] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.553981] ohci-st: OHCI STMicroelectronics driver <6>[ 4.559304] ohci-atmel: OHCI Atmel driver <6>[ 4.564716] usbcore: registered new interface driver usb-storage <6>[ 4.578397] i2c /dev entries driver <3>[ 4.599794] CPUidle arm: CPU 0 failed to init idle CPU ops <6>[ 4.606194] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.612641] sdhci: Copyright(c) Pierre Ossman <6>[ 4.619766] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.627782] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.638662] sdhci-esdhc-imx 30b40000.mmc: Got CD GPIO <6>[ 4.644011] sdhci-esdhc-imx 30b40000.mmc: Got WP GPIO <6>[ 4.654427] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.662006] usbcore: registered new interface driver usbhid <6>[ 4.667892] usbhid: USB HID core driver <6>[ 4.678304] NET: Registered protocol family 10 <6>[ 4.684254] Segment Routing with IPv6 <6>[ 4.688320] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.695166] NET: Registered protocol family 17 <6>[ 4.699935] can: controller area network core <6>[ 4.704624] NET: Registered protocol family 29 <6>[ 4.709370] can: raw protocol <6>[ 4.712609] can: broadcast manager protocol <6>[ 4.717084] can: netlink gateway - max_hops=1 <5>[ 4.722265] Key type dns_resolver registered <6>[ 4.726972] ThumbEE CPU extension supported. <5>[ 4.731518] Registering SWP/SWPB emulation handler <5>[ 4.737078] Loading compiled-in X.509 certificates <6>[ 4.776914] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <4>[ 4.788012] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.796546] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA <4>[ 4.819007] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.828001] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.839814] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 4.862426] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.871399] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.883152] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.894344] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.916329] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.925162] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.937117] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.945338] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <4>[ 4.967162] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.976083] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.987880] pwm-backlight backlight: supply power not found, using dummy regulator <3>[ 5.002679] fec 30bf0000.ethernet eth0: Unable to connect to phy <3>[ 5.012472] IP-Config: Failed to open eth0 <3>[ 5.016884] IP-Config: No network devices available <6>[ 5.036470] mmc0: new high speed SDHC card at address e624 <6>[ 5.043172] mmcblk0: mmc0:e624 SA16G 14.8 GiB <6>[ 5.052546] Freeing unused kernel memory: 2048K <6>[ 5.059235] Run /init as init process <6>[ 5.063425] mmcblk0: p1 p2 <4>[ 5.088630] imx_usb 30b10000.usb: No over current polarity defined <4>[ 5.097682] imx_usb 30b20000.usb: No over current polarity defined <4>[ 5.109521] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 5.119958] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 5.134262] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 5.148089] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.333031] udevd[128]: starting version 3.2.9 <5>[ 5.345307] random: udevd: uninitialized urandom read (16 bytes read) <6>[ 5.354370] mmc1: new ultra high speed SDR104 SDIO card at address 0001 <5>[ 5.362191] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.369410] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.386037] udevd[128]: specified user 'tss' unknown <27>[ 5.391545] udevd[128]: specified group 'tss' unknown <30>[ 5.407090] udevd[129]: starting eudev-3.2.9 <5>[ 5.537358] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 6.098976] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 6.106093] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 6.114976] cfg80211: failed to load regulatory.db <6>[ 6.231989] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 6.241180] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <4>[ 6.274237] imx_usb 30b10000.usb: No over current polarity defined <4>[ 6.283308] imx_usb 30b20000.usb: No over current polarity defined <4>[ 6.295156] pwm-backlight backlight: supply power not found, using dummy regulator <3>[ 7.315450] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 <4>[ 7.457616] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.465844] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 7.474681] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 7.482832] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 7.493736] imx_usb 30b10000.usb: No over current polarity defined <6>[ 7.562949] gpio-expander@0 enforce active low on chipselect handle <4>[ 7.718632] imx_usb 30b20000.usb: No over current polarity defined <6>[ 7.805476] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 7.810698] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 7.965463] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.016441] hub 1-0:1.0: USB hub found <6>[ 8.085462] hub 1-0:1.0: 1 port detected <4>[ 8.141888] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 8.733852] caam 30900000.crypto: Entropy delay = 3200 <6>[ 8.798788] caam 30900000.crypto: Instantiated RNG4 SH0 <6>[ 8.858199] caam 30900000.crypto: Instantiated RNG4 SH1 <6>[ 8.863702] caam 30900000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 8.870685] caam 30900000.crypto: job rings = 3, qi = 0 <4>[ 8.910910] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 9.402454] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 10.921769] caam algorithms registered in /proc/crypto <6>[ 10.929071] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 10.936854] caam 30900000.crypto: registering rng-caam <4>[ 10.948944] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 11.002063] pwm-backlight backlight: supply power not found, using dummy regulator done Saving random seed: <5>[ 11.037694] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 11.120684] random: crng init done OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1237590/environment . /lava-1237590/environment / # /lava-1237590/bin/lava-test-runner /lava-1237590/0 /lava-1237590/bin/lava-test-runner /lava-1237590/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1237590/0/tests/0_dmesg + cat uuid + UUID=1237590_1.5.2.4<8>[ 16.935962] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.984156] <8>[ 17.027780] <8>[ 17.071284] + set<8>[ 17.081575] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1237590/environment / # . /lava-1237590/environment /lava-1237590/bin/lava-test-runner /lava-1237590/1 / # /lava-1237590/bin/lava-test-runner /lava-1237590/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1237590/1/tests/1_bootrr +<8>[ 22.795033] cat uuid + UUID=1237590_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1237590/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto imx-pgc-domain.0 imx-pgc: Failed to get domain's regulator imx-pgc-domain.1 imx-pgc: Failed to get domain's regulator imx-pgc-domain.2 imx-pgc: Failed to get domain's regulator panel 30be0000.ethernet usbphynop3 30730000.lcdif 30360000.anatop:tempmon imx_thermal: failed to register cpufreq cooling device regulator-lcd-3v3 backlight /lava-1237590/1/../bin/lava-test-case <8>[ 23.852677] /lava-1237590/1/../bin/lava-test-case <8>[ 24.896524] /lava-1237590/1/../bin/lava-test-case <8>[ 24.921609] + set +x <8>[ 24.940854] / #