[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.191 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11879160/tftp-deploy-bf65sjfl/kernel/zImage tftp 0x10000000 11879160/tftp-deploy-bf65sjfl/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11879160/tftp-deploy-bf65sjfl/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 2.9 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 11879160/tftp-deploy-bf65sjfl/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11879160/tftp-deploy-bf65sjfl/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11879160/tftp-deploy-bf65sjfl/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 4 MiB/s done Bytes transferred = 16080370 (f55df2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11879160/tftp-deploy-bf65sjfl/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11879160/tftp-deploy-bf65sjfl/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11879160/tftp-deploy-bf65sjfl/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.3 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16080306 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.199 (KernelCI@build-j80579-arm-gcc-10-multi-v7-defconfig-tmqxd) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Oct 25 23:27:31 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932652K/1048576K available (14336K kernel code, 2239K rwdata, 5360K rodata, 2048K init, 424K bss, 50388K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008094] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.022100] Console: colour dummy device 80x30 <6>[ 0.023990] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034661] CPU: Testing write buffer coherency: ok <6>[ 0.039794] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.045091] pid_max: default: 32768 minimum: 301 <6>[ 0.050117] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057557] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066423] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072166] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079949] rcu: Hierarchical SRCU implementation. <6>[ 0.087129] EFI services will not be available. <6>[ 0.089364] smp: Bringing up secondary CPUs ... <6>[ 0.094658] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094667] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106044] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.106051] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117203] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.117211] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127643] smp: Brought up 1 node, 4 CPUs <6>[ 0.131872] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.138415] CPU: All CPU(s) started in SVC mode. <6>[ 0.143836] devtmpfs: initialized <6>[ 0.154069] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159415] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169282] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179499] pinctrl core: initialized pinctrl subsystem <6>[ 0.184017] DMI not present or invalid. <6>[ 0.187085] NET: Registered protocol family 16 <6>[ 0.194374] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.201103] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201296] cpuidle: using governor menu <6>[ 0.209292] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.384274] vdd1p1: supplied by regulator-dummy <6>[ 0.393232] vdd3p0: supplied by regulator-dummy <6>[ 0.402129] vdd2p5: supplied by regulator-dummy <6>[ 0.411056] vddarm: supplied by regulator-dummy <6>[ 0.420141] vddpu: supplied by regulator-dummy <6>[ 0.428829] vddsoc: supplied by regulator-dummy <6>[ 0.750347] No ATAGs? <6>[ 0.750535] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.758310] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.768671] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.779247] Serial: AMBA PL011 UART driver <6>[ 0.783534] printk: console [ramoops-1] enabled <6>[ 0.785777] pstore: Registered ramoops as persistent store backend <6>[ 0.791977] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.830147] iommu: Default domain type: Translated <6>[ 0.832870] vgaarb: loaded <5>[ 0.836328] SCSI subsystem initialized <6>[ 0.840003] usbcore: registered new interface driver usbfs <6>[ 0.845181] usbcore: registered new interface driver hub <6>[ 0.850771] usbcore: registered new device driver usb <6>[ 0.857611] i2c i2c-0: IMX I2C adapter registered <6>[ 0.862289] i2c i2c-1: IMX I2C adapter registered <6>[ 0.866803] i2c i2c-2: IMX I2C adapter registered <6>[ 0.872351] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.876133] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.885530] PTP clock support registered <6>[ 0.893323] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.047819] NET: Registered protocol family 2 <6>[ 2.050016] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.058655] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.065921] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.073962] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.081393] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.088118] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.094810] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.102228] NET: Registered protocol family 1 <6>[ 2.107292] RPC: Registered named UNIX socket transport module. <6>[ 2.112840] RPC: Registered udp transport module. <6>[ 2.117834] RPC: Registered tcp transport module. <6>[ 2.122756] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.129483] PCI: CLS 0 bytes, default 64 <6>[ 2.134134] Trying to unpack rootfs image as initramfs... <6>[ 3.487733] Freeing initrd memory: 15704K <4>[ 3.489660] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.497003] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.506837] Initialise system trusted keyrings <6>[ 3.509896] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.522201] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.526231] NFS: Registering the id_resolver key type <5>[ 3.530785] Key type id_resolver registered <5>[ 3.535218] Key type id_legacy registered <6>[ 3.539554] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.546433] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.554116] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.559164] Key type asymmetric registered <5>[ 3.563034] Asymmetric key parser 'x509' registered <6>[ 3.568234] bounce: pool size: 64 pages <6>[ 3.572284] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.579929] io scheduler mq-deadline registered <6>[ 3.584708] io scheduler kyber registered <6>[ 3.630245] mxs-dma 110000.dma-controller: initialized <4>[ 3.637695] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.645507] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.701067] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.709355] SuperH (H)SCI(F) driver initialized <6>[ 3.712300] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.721200] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.729098] printk: console [ttymxc1] enabled <6>[ 3.729098] printk: console [ttymxc1] enabled <6>[ 3.738274] printk: bootconsole [ec_imx21] disabled <6>[ 3.738274] printk: bootconsole [ec_imx21] disabled <6>[ 3.750112] msm_serial: driver initialized <6>[ 3.756036] STMicroelectronics ASC driver initialized <6>[ 3.763424] STM32 USART driver initialized <4>[ 3.779152] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.787086] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.793944] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.810699] brd: module loaded <6>[ 3.821490] loop: module loaded <6>[ 3.828955] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.837169] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.845455] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.853923] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.861917] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.869678] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.877241] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.887833] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.895121] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.904197] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.915017] scsi host0: ahci-imx <6>[ 3.918876] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.939839] CAN device driver interface <6>[ 3.945401] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.954925] pps pps0: new PPS source ptp0 <6>[ 3.991821] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.999517] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.004774] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.011020] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.016702] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.029024] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.036755] usbcore: registered new interface driver pegasus <6>[ 4.042730] usbcore: registered new interface driver asix <6>[ 4.048448] usbcore: registered new interface driver ax88179_178a <6>[ 4.054861] usbcore: registered new interface driver cdc_ether <6>[ 4.061004] usbcore: registered new interface driver smsc75xx <6>[ 4.067077] usbcore: registered new interface driver smsc95xx <6>[ 4.073122] usbcore: registered new interface driver net1080 <6>[ 4.079097] usbcore: registered new interface driver cdc_subset <6>[ 4.085339] usbcore: registered new interface driver zaurus <6>[ 4.091253] usbcore: registered new interface driver cdc_ncm <6>[ 4.100956] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.107775] ehci-pci: EHCI PCI platform driver <6>[ 4.112525] ehci-platform: EHCI generic platform driver <6>[ 4.118365] ehci-orion: EHCI orion driver <6>[ 4.122878] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.127365] ehci-st: EHCI STMicroelectronics driver <6>[ 4.132700] ehci-exynos: EHCI Exynos driver <6>[ 4.137357] ehci-atmel: EHCI Atmel driver <6>[ 4.141814] tegra-ehci: Tegra EHCI driver <6>[ 4.146336] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.152801] ohci-pci: OHCI PCI platform driver <6>[ 4.157571] ohci-platform: OHCI generic platform driver <6>[ 4.163360] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.167838] ohci-st: OHCI STMicroelectronics driver <6>[ 4.173180] ohci-atmel: OHCI Atmel driver <6>[ 4.178638] usbcore: registered new interface driver usb-storage <6>[ 4.193413] i2c /dev entries driver <6>[ 4.217773] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.224247] sdhci: Copyright(c) Pierre Ossman <6>[ 4.231771] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.240155] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.247422] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.247641] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.252710] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.263424] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.270816] usbcore: registered new interface driver usbhid <6>[ 4.273667] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.276682] usbhid: USB HID core driver <6>[ 4.282373] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.289766] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.292989] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.293259] NET: Registered protocol family 10 <6>[ 4.294393] Segment Routing with IPv6 <6>[ 4.294467] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.295033] NET: Registered protocol family 17 <6>[ 4.295047] can: controller area network core <6>[ 4.295124] NET: Registered protocol family 29 <6>[ 4.295130] can: raw protocol <6>[ 4.295138] can: broadcast manager protocol <6>[ 4.295148] can: netlink gateway - max_hops=1 <5>[ 4.295549] Key type dns_resolver registered <6>[ 4.297290] ThumbEE CPU extension supported. <5>[ 4.297303] Registering SWP/SWPB emulation handler <5>[ 4.300281] Loading compiled-in X.509 certificates <6>[ 4.307867] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.317522] pstore: Using crash dump compression: deflate <6>[ 4.357940] mmc2: new high speed SDHC card at address 0001 <4>[ 4.383481] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 4.387709] mmcblk2: mmc2:0001 SD 14.8 GiB <4>[ 4.394724] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.407860] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.417433] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.425141] GPT:29296874 != 30965759 <4>[ 4.428984] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.435273] GPT:29296874 != 30965759 <4>[ 4.439115] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.444575] mmcblk2: p1 p2 p3 <4>[ 4.451737] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.461766] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.466980] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.503314] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.510318] hub 1-0:1.0: USB hub found <6>[ 4.514480] hub 1-0:1.0: 1 port detected <3>[ 4.522780] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 4.530405] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 4.538788] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 4.551173] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.559104] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.567363] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.580575] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.588503] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.596723] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.607113] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.620227] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.628198] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.636548] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.650297] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 4.863389] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 5.065062] hub 1-1:1.0: USB hub found <6>[ 5.069283] hub 1-1:1.0: 3 ports detected <4>[ 5.084211] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.092250] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.102209] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.723838] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.733400] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.763367] Sending DHCP requests ., OK <6>[ 6.807526] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.191 <6>[ 6.815959] IP-Config: Complete: <6>[ 6.819479] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.191, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.830311] host=192.168.201.191, domain=lava-rack, nis-domain=(none) <6>[ 6.837497] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.837509] nameserver0=192.168.201.1 <6>[ 6.856254] Freeing unused kernel memory: 2048K <6>[ 6.884364] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.037992] udevd[132]: starting version 3.2.9 <5>[ 7.043909] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.050862] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.057734] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.073068] udevd[132]: specified user 'tss' unknown <27>[ 7.078606] udevd[132]: specified group 'tss' unknown <30>[ 7.086974] udevd[133]: starting eudev-3.2.9 <6>[ 7.454425] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.461878] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.473070] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.481118] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.500731] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.519859] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.527869] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.537766] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.552386] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.560408] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.652876] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.661655] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.670441] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.679169] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.785692] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.799996] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.808102] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.838673] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.950243] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.963493] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.977530] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.023632] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.030452] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.043652] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.104412] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.109844] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.116761] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.127737] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.134199] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.140603] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.194195] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.214040] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.222568] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.231316] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.239938] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.250701] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.256159] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.259021] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.266729] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.275196] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 8.282471] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.284321] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.290321] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.297252] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.319812] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.328426] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.337017] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.349671] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.357951] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.368205] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.385540] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.393044] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.402084] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.410686] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.419278] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.460628] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.468700] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.491390] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.514874] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.523527] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.532100] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.540692] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.706846] caam algorithms registered in /proc/crypto <6>[ 8.714110] caam 2100000.crypto: registering rng-caam <4>[ 8.721362] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.729430] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.738127] panel-simple panel-lvds0: supply power not found, using dummy regulator done <6>[ 8.756995] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Saving random seed: <6>[ 8.765601] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.775879] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <5>[ 8.776871] random: dd: uninitialized urandom read (32 bytes read) <6>[ 8.784413] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) OK <4>[ 8.812157] panel-simple panel-lcd: supply power not found, using dummy regulator Starting network: <4>[ 8.820252] panel-simple panel-lcd: Specify missing connector_type ip: RTNETLINK answers: File exists FAIL <5>[ 8.901909] random: crng init done <5>[ 8.905709] random: 1 urandom warning(s) missed due to ratelimiting Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11879160/environment . /lava-11879160/environment / # /lava-11879160/bin/lava-test-runner /lava-11879160/0 /lava-11879160/bin/lava-test-runner /lava-11879160/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11879160/0/tests/0_dmesg + cat uuid + UUID=11879160_1.5.2<8>[ 9.556656] .4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.602995] <8>[ 9.644379] <8>[ 9.685607] + set<8>[ 9.695658] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11879160/environment / # . /lava-11879160/environment/lava-11879160/bin/lava-test-runner /lava-11879160/1 / # /lava-11879160/bin/lava-test-runner /lava-11879160/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11879160/1/tests/1_bootrr + cat uuid + UUID=11879160_1.5.2.4.5<8>[ 10.225435] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11879160/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds 120000.hdmi panel-lcd /lava-11879160/1/../bin/lava-test-case <8>[ 11.314128] /lava-11879160/1/../bin/lava-test-case <8>[ 11.364792] /lava-11879160/1/../bin/lava-test-case <8>[ 11.390551] + set +x <8>[ 11.419738] / #