Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1010526/tftp-deploy-ta506jgr/kernel/zImage tftp 0x82000000 1010526/tftp-deploy-ta506jgr/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1010526/tftp-deploy-ta506jgr/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.1 MiB/s done Bytes transferred = 4611912 (465f48 hex) => tftp 0x83000000 1010526/tftp-deploy-ta506jgr/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1010526/tftp-deploy-ta506jgr/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1010526/tftp-deploy-ta506jgr/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.1 MiB/s done Bytes transferred = 14169548 (d835cc hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1010526/tftp-deploy-ta506jgr/dtb/am335x-boneblack.dtb tftp 0x88000000 1010526/tftp-deploy-ta506jgr/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1010526/tftp-deploy-ta506jgr/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-09-19 21:06:00 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14169484 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.194-cip39-rt15 (KernelCI@build-j51168-arm-gcc-10-omap2plus-defconfig-5jrjl) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Sep 19 20:41:50 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] On node 0 totalpages: 130560 [ 0.000000] Normal zone: 1148 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 130560 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s33484 r8192 d23860 u65536 [ 0.000000] pcpu-alloc: s33484 r8192 d23860 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472032K/522240K available (9216K kernel code, 1044K rwdata, 2180K rodata, 1024K init, 272K bss, 33824K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008337] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018543] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030210] Console: colour dummy device 80x30 <3>[ 0.035085] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042142] This ensures that you still see kernel messages. Please <3>[ 0.048868] update your kernel commandline. <6>[ 0.053470] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095544] CPU: Testing write buffer coherency: ok <6>[ 0.100924] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106391] pid_max: default: 32768 minimum: 301 <6>[ 0.111560] LSM: Security Framework initializing <6>[ 0.116657] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124477] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134123] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140679] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147884] rcu: Hierarchical SRCU implementation. <6>[ 0.153664] smp: Bringing up secondary CPUs ... <6>[ 0.158601] smp: Brought up 1 node, 1 CPU <6>[ 0.163028] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169760] CPU: All CPU(s) started in SVC mode. <6>[ 0.175487] devtmpfs: initialized <6>[ 0.191084] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199625] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210072] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218609] pinctrl core: initialized pinctrl subsystem <6>[ 0.226247] NET: Registered protocol family 16 <6>[ 0.233883] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260326] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266420] audit: initializing netlink subsys (disabled) <6>[ 0.273493] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273505] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.273510] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.273769] cpuidle: using governor menu <5>[ 1.167313] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.292814] No ATAGs? <6>[ 1.295446] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.319945] Kprobes globally optimized <7>[ 1.330309] reg-fixed-voltage fixedregulator0: GPIO lookup for consumer (null) <7>[ 1.338042] reg-fixed-voltage fixedregulator0: using device tree for GPIO lookup <7>[ 1.346006] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/fixedregulator0[0]' <7>[ 1.355361] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator0[0]' <7>[ 1.364606] reg-fixed-voltage fixedregulator0: using lookup tables for GPIO lookup <7>[ 1.372677] reg-fixed-voltage fixedregulator0: No GPIO consumer (null) found <6>[ 1.382900] iommu: Default domain type: Translated <6>[ 1.390016] vgaarb: loaded <5>[ 1.393601] SCSI subsystem initialized <7>[ 1.398094] libata version 3.00 loaded. <6>[ 1.402957] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.408342] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.418080] PTP clock support registered <6>[ 1.423882] clocksource: Switched to clocksource dmtimer <5>[ 2.093850] VFS: Disk quotas dquot_6.6.0 <6>[ 2.098263] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.115487] NET: Registered protocol family 2 <6>[ 2.120553] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.129270] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.138237] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.146535] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.154217] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.161129] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.168159] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.175776] NET: Registered protocol family 1 <6>[ 2.181595] RPC: Registered named UNIX socket transport module. <6>[ 2.188062] RPC: Registered udp transport module. <6>[ 2.193172] RPC: Registered tcp transport module. <6>[ 2.198296] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.205225] PCI: CLS 0 bytes, default 64 <6>[ 2.210251] Trying to unpack rootfs image as initramfs... <6>[ 3.198162] Freeing initrd memory: 13840K <6>[ 3.203933] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.214347] Initialise system trusted keyrings <6>[ 3.219651] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.227896] NFS: Registering the id_resolver key type <5>[ 3.233453] Key type id_resolver registered <5>[ 3.238099] Key type id_legacy registered <6>[ 3.242551] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.250526] Key type asymmetric registered <5>[ 3.255060] Asymmetric key parser 'x509' registered <6>[ 3.260362] io scheduler mq-deadline registered <6>[ 3.265312] io scheduler kyber registered <3>[ 3.403948] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.412586] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.521727] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.563900] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.635700] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.644399] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.704471] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.713106] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.730620] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.739310] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.802915] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.811487] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.838489] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <7>[ 3.847420] gpio-clk clk_mcasp0: GPIO lookup for consumer enable <7>[ 3.853986] gpio-clk clk_mcasp0: using device tree for GPIO lookup <7>[ 3.860641] gpio-clk clk_mcasp0: No GPIO consumer enable found <6>[ 3.872507] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <7>[ 3.883251] omap8250 44e09000.serial: GPIO lookup for consumer rs485-term <7>[ 3.890673] omap8250 44e09000.serial: using device tree for GPIO lookup <7>[ 3.897802] of_get_named_gpiod_flags: can't parse 'rs485-term-gpios' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.912890] of_get_named_gpiod_flags: can't parse 'rs485-term-gpio' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.927876] omap8250 44e09000.serial: using lookup tables for GPIO lookup <7>[ 3.935147] omap8250 44e09000.serial: No GPIO consumer rs485-term found <6>[ 3.942263] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.951685] printk: console [ttyS0] enabled <6>[ 3.951685] printk: console [ttyS0] enabled <6>[ 3.960748] printk: bootconsole [omap8250] disabled <6>[ 3.960748] printk: bootconsole [omap8250] disabled <6>[ 3.984900] brd: module loaded <6>[ 3.995668] loop: module loaded <3>[ 4.001113] mtdoops: mtd device (mtddev=name/number) must be supplied <7>[ 4.010296] mdio_bus fixed-0: GPIO lookup for consumer reset <7>[ 4.016353] mdio_bus fixed-0: using lookup tables for GPIO lookup <7>[ 4.022744] mdio_bus fixed-0: No GPIO consumer reset found <7>[ 4.033006] mdio_bus 4a101000.mdio: GPIO lookup for consumer reset <7>[ 4.039612] mdio_bus 4a101000.mdio: using device tree for GPIO lookup <7>[ 4.046388] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 4.061468] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 4.076451] mdio_bus 4a101000.mdio: using lookup tables for GPIO lookup <7>[ 4.083361] mdio_bus 4a101000.mdio: No GPIO consumer reset found <6>[ 4.143814] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <7>[ 4.185242] mdio_bus 4a101000.mdio:00: GPIO lookup for consumer reset <7>[ 4.192022] mdio_bus 4a101000.mdio:00: using device tree for GPIO lookup <7>[ 4.199137] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 4.215556] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 4.231855] mdio_bus 4a101000.mdio:00: using lookup tables for GPIO lookup <7>[ 4.239046] mdio_bus 4a101000.mdio:00: No GPIO consumer reset found <6>[ 4.246877] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.256774] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.263434] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.269235] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.276822] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.285861] i2c /dev entries driver <5>[ 4.291338] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.299272] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.305820] sdhci: Copyright(c) Pierre Ossman <6>[ 4.311165] sdhci-pltfm: SDHCI platform and OF driver helper <7>[ 4.318190] sdhci-omap 48060000.mmc: GPIO lookup for consumer cd <7>[ 4.324608] sdhci-omap 48060000.mmc: using device tree for GPIO lookup <7>[ 4.331459] sdhci-omap 48060000.mmc: No GPIO consumer cd found <7>[ 4.338502] sdhci-omap 481d8000.mmc: GPIO lookup for consumer wp <7>[ 4.344903] sdhci-omap 481d8000.mmc: using device tree for GPIO lookup <7>[ 4.351740] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.365642] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.379412] sdhci-omap 481d8000.mmc: using lookup tables for GPIO lookup <7>[ 4.386429] sdhci-omap 481d8000.mmc: No GPIO consumer wp found <4>[ 4.392722] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.401293] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.409644] Initializing XFRM netlink socket <6>[ 4.414464] NET: Registered protocol family 10 <6>[ 4.420677] Segment Routing with IPv6 <6>[ 4.424820] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.431786] NET: Registered protocol family 17 <6>[ 4.436626] NET: Registered protocol family 15 <5>[ 4.441460] Key type dns_resolver registered <6>[ 4.446667] oprofile: using arm/armv7 <6>[ 4.450715] ThumbEE CPU extension supported. <5>[ 4.455353] Registering SWP/SWPB emulation handler <3>[ 4.460826] omap_voltage_late_init: Voltage driver support not added <3>[ 4.467547] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.475982] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.484661] SmartReflex Class3 initialized <6>[ 4.491307] printk: console [ttyS0]: printing thread started <5>[ 4.491389] Loading compiled-in X.509 certificates <6>[ 4.510266] OMAP GPIO hardware version 0.1 <6>[ 4.526819] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <4>[ 4.554324] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.561898] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.576519] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.577266] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.581222] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.586478] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.586489] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.586745] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.634550] mmc1: new high speed MMC card at address 0001 <6>[ 4.635613] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.636038] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.636439] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.636783] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.638862] mmcblk1: p1 <6>[ 4.677633] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.679146] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.755179] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.894278] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.903642] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.933749] Sending DHCP requests ., OK <6>[ 7.973609] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 7.973631] IP-Config: Complete: <6>[ 7.973634] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.973648] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.973654] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.973661] nameserver0=192.168.11.1 <6>[ 7.976302] Freeing unused kernel memory: 1024K <6>[ 8.034109] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.267944] udevd[101]: starting version 3.2.9 <5>[ 8.269392] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.269859] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.269989] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.306069] udevd[101]: specified user 'tss' unknown <27>[ 8.306284] udevd[101]: specified group 'tss' unknown <30>[ 8.316463] udevd[102]: starting eudev-3.2.9 <6>[ 9.011969] remoteproc remoteproc0: wkup_m3 is available <4>[ 9.188220] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.188578] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 9.255234] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.255547] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.580161] usbcore: registered new interface driver usbfs <6>[ 9.580236] usbcore: registered new interface driver hub <6>[ 9.580319] usbcore: registered new device driver usb <6>[ 9.789072] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.789124] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.881157] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.881191] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.881200] usb usb1: Product: MUSB HDRC host driver <6>[ 9.881208] usb usb1: Manufacturer: Linux 5.10.194-cip39-rt15 musb-hcd <6>[ 9.881215] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.884951] hub 1-0:1.0: USB hub found <6>[ 9.885041] hub 1-0:1.0: 1 port detected <4>[ 9.931637] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 10.007926] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 10.008384] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 10.038202] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 10.066385] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 10.107634] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 10.181972] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 10.248959] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 10.274552] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 10.294223] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 10.322444] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 10.322512] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <3>[ 10.463717] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.691921] tda998x 0-0070: found TDA19988 <3>[ 10.714029] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 11.080302] davinci-mcasp 48038000.mcasp: IRQ common not found <3>[ 11.224639] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 11.234322] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 11.274196] remoteproc remoteproc0: powering up wkup_m3 <4>[ 11.274339] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 11.274358] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 11.274365] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 11.863988] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 11.874600] random: crng init done <6>[ 11.881159] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 11.893097] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 11.893491] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 11.929678] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 12.179637] PM: Cannot get wkup_m3_ipc handle <6>[ 12.477930] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.507414] omap-aes 53500000.aes: will run requests pump with realtime priority <6>[ 12.520820] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.524631] omap-sham 53100000.sham: will run requests pump with realtime priority <3>[ 12.551873] PM: Cannot get wkup_m3_ipc handle <3>[ 12.576525] PM: Cannot get wkup_m3_ipc handle <3>[ 13.133446] PM: Cannot get wkup_m3_ipc handle <3>[ 13.171100] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1010526/environment . /lava-1010526/environment / # /lava-1010526/bin/lava-test-runner /lava-1010526/0 /lava-1010526/bin/lava-test-runner /lava-1010526/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1010526/0/tests/0_dmesg + cat uuid + UUID=1010526_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.081254] <8>[ 14.149931] <8>[ 14.210139] + set +x <8>[ 14.270347] / # <8>[ 14.272433] #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1010526/environment / # . /lava-1010526/environment/lava-1010526/bin/lava-test-runner /lava-1010526/1 / # /lava-1010526/bin/lava-test-runner /lava-1010526/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1010526/1/tests/1_bootrr + cat uuid + UUID=1010526_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1010526/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/boo<8>[ 14.794606] trr/libexec/bootrr + sh helpers/bootrr-auto pm33xx /lava-1010526/1/../bin/lava-test-case <8>[ 15.902184] /lava-1010526/1/../bin/lava-test-case <8>[ 15.957400] /lava-1010526/1/../bin/lava-test-case <8>[ 15.990257] /lava-1010526/1/../bin/lava-test-case <8>[ 16.051519] /lava-1010526/1/../bin/lava-test-case <8>[ 16.102302] /lava-1010526/1/../bin/lava-test-case <8>[ 16.143418] /lava-1010526/1/../bin/lava-test-case <8>[ 16.194407] /lava-1010526/1/../bin/lava-test-case <8>[ 16.244336] /lava-1010526/1/../bin/lava-test-case <8>[ 16.301041] /lava-1010526/1/../bin/lava-test-case <8>[ 16.351094] /lava-1010526/1/../bin/lava-test-case <8>[ 16.391587] /lava-1010526/1/../bin/lava-test-case <8>[ 16.442025] /lava-1010526/1/../bin/lava-test-case <8>[ 16.482514] /lava-1010526/1/../bin/lava-test-case <8>[ 16.522566] /lava-1010526/1/../bin/lava-test-case <8>[ 16.563357] /lava-1010526/1/../bin/lava-test-case <8>[ 16.613166] /lava-1010526/1/../bin/lava-test-case <8>[ 16.655193] /lava-1010526/1/../bin/lava-test-case <8>[ 16.705951] /lava-1010526/1/../bin/lava-test-case <8>[ 16.755755] /lava-1010526/1/../bin/lava-test-case <8>[ 16.796228] /lava-1010526/1/../bin/lava-test-case <8>[ 16.846850] /lava-1010526/1/../bin/lava-test-case <8>[ 16.897583] /lava-1010526/1/../bin/lava-test-case <8>[ 16.938668] /lava-1010526/1/../bin/lava-test-case <8>[ 16.989744] /lava-1010526/1/../bin/lava-test-case <8>[ 17.030671] /lava-1010526/1/../bin/lava-test-case <8>[ 17.081150] /lava-1010526/1/../bin/lava-test-case <8>[ 17.122043] /lava-1010526/1/../bin/lava-test-case <8>[ 18.202308] /lava-1010526/1/../bin/lava-test-case <8>[ 18.244046] /lava-1010526/1/../bin/lava-test-case <8>[ 18.294833] /lava-1010526/1/../bin/lava-test-case <8>[ 18.336145] /lava-1010526/1/../bin/lava-test-case <8>[ 18.386430] /lava-1010526/1/../bin/lava-test-case <8>[ 18.426762] /lava-1010526/1/../bin/lava-test-case <8>[ 18.477300] /lava-1010526/1/../bin/lava-test-case <8>[ 18.517823] /lava-1010526/1/../bin/lava-test-case <8>[ 18.568851] /lava-1010526/1/../bin/lava-test-case <8>[ 18.608817] /lava-1010526/1/../bin/lava-test-case <8>[ 18.659412] /lava-1010526/1/../bin/lava-test-case <8>[ 18.700157] /lava-1010526/1/../bin/lava-test-case <8>[ 18.750906] /lava-1010526/1/../bin/lava-test-case <8>[ 18.791488] /lava-1010526/1/../bin/lava-test-case <8>[ 18.842484] /lava-1010526/1/../bin/lava-test-case <8>[ 18.883528] /lava-1010526/1/../bin/lava-test-case <8>[ 18.934396] /lava-1010526/1/../bin/lava-test-case <8>[ 18.974719] /lava-1010526/1/../bin/lava-test-case <8>[ 19.025350] /lava-1010526/1/../bin/lava-test-case <8>[ 19.066283] /lava-1010526/1/../bin/lava-test-case <8>[ 19.116501] /lava-1010526/1/../bin/lava-test-case /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: <8>[ 19.157314] line 84: assert_device-present: not found /lava-1010526/1/../bin/lava-test-case <8>[ 19.200238] /lava-1010526/1/../bin/lava-test-case <8>[ 19.250916] /lava-1010526/1/../bin/lava-test-case <8>[ 19.298453] + set +x