Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1018657/tftp-deploy-63qlhs5u/kernel/zImage tftp 0x82000000 1018657/tftp-deploy-63qlhs5u/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1018657/tftp-deploy-63qlhs5u/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 5.1 MiB/s done Bytes transferred = 9708032 (942200 hex) => tftp 0x83000000 1018657/tftp-deploy-63qlhs5u/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1018657/tftp-deploy-63qlhs5u/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1018657/tftp-deploy-63qlhs5u/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.2 MiB/s done Bytes transferred = 16084577 (f56e61 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1018657/tftp-deploy-63qlhs5u/dtb/am335x-boneblack.dtb tftp 0x88000000 1018657/tftp-deploy-63qlhs5u/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1018657/tftp-deploy-63qlhs5u/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-10-10 11:00:31 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16084513 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.197-cip39 (KernelCI@build-j68479-arm-gcc-10-multi-v7-defconfig-b5mv2) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Oct 10 10:01:49 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 410836K/522240K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 45868K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000012] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008340] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019062] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033122] Console: colour dummy device 80x30 <3>[ 0.037987] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045031] This ensures that you still see kernel messages. Please <3>[ 0.051752] update your kernel commandline. <6>[ 0.056359] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096028] CPU: Testing write buffer coherency: ok <6>[ 0.101393] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106852] pid_max: default: 32768 minimum: 301 <6>[ 0.112033] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.119842] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.129156] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135497] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.144690] rcu: Hierarchical SRCU implementation. <6>[ 0.154529] EFI services will not be available. <6>[ 0.159713] smp: Bringing up secondary CPUs ... <6>[ 0.164643] smp: Brought up 1 node, 1 CPU <6>[ 0.169032] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.175771] CPU: All CPU(s) started in SVC mode. <6>[ 0.181386] devtmpfs: initialized <6>[ 0.195450] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.203985] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.214413] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.225569] pinctrl core: initialized pinctrl subsystem <6>[ 0.233911] DMI not present or invalid. <6>[ 0.238877] NET: Registered protocol family 16 <6>[ 0.246353] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.272931] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.281130] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.281331] cpuidle: using governor menu <6>[ 1.334368] No ATAGs? <6>[ 1.336992] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.351496] Serial: AMBA PL011 UART driver <6>[ 1.389548] iommu: Default domain type: Translated <6>[ 1.395285] vgaarb: loaded <5>[ 1.399434] SCSI subsystem initialized <6>[ 1.404436] usbcore: registered new interface driver usbfs <6>[ 1.410472] usbcore: registered new interface driver hub <6>[ 1.416248] usbcore: registered new device driver usb <6>[ 1.423553] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.428935] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.438663] PTP clock support registered <6>[ 1.446735] clocksource: Switched to clocksource dmtimer <6>[ 2.417158] NET: Registered protocol family 2 <6>[ 2.422183] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.430684] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.439608] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.447890] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.455544] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.462469] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.469488] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.477077] NET: Registered protocol family 1 <6>[ 2.482685] RPC: Registered named UNIX socket transport module. <6>[ 2.489130] RPC: Registered udp transport module. <6>[ 2.494234] RPC: Registered tcp transport module. <6>[ 2.499352] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.506251] PCI: CLS 0 bytes, default 64 <6>[ 2.511263] Trying to unpack rootfs image as initramfs... <6>[ 3.576402] Freeing initrd memory: 15708K <6>[ 3.581827] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.592181] Initialise system trusted keyrings <6>[ 3.597532] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.610691] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.618015] NFS: Registering the id_resolver key type <5>[ 3.623544] Key type id_resolver registered <5>[ 3.628177] Key type id_legacy registered <6>[ 3.632686] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.639895] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.647822] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.653141] Key type asymmetric registered <5>[ 3.657680] Asymmetric key parser 'x509' registered <6>[ 3.663014] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.670913] io scheduler mq-deadline registered <6>[ 3.675839] io scheduler kyber registered <3>[ 3.828639] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.837329] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.956272] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 4.001402] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 4.079135] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.087838] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 4.152795] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.161490] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 4.179981] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.188689] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.257321] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.265774] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.307998] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.411560] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 4.423886] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.433315] printk: console [ttyS0] enabled <6>[ 4.433315] printk: console [ttyS0] enabled <6>[ 4.442372] printk: bootconsole [omap8250] disabled <6>[ 4.442372] printk: bootconsole [omap8250] disabled <6>[ 4.456141] SuperH (H)SCI(F) driver initialized <6>[ 4.463205] msm_serial: driver initialized <6>[ 4.468126] STMicroelectronics ASC driver initialized <6>[ 4.476166] STM32 USART driver initialized <6>[ 4.483631] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 4.503010] random: crng init done <6>[ 4.516190] brd: module loaded <6>[ 4.525851] loop: module loaded <6>[ 4.550905] CAN device driver interface <6>[ 4.557041] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 4.565271] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.570593] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.576945] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.582630] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.656770] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.693163] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.703094] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.709801] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.715632] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.724784] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.732718] usbcore: registered new interface driver pegasus <6>[ 4.738756] usbcore: registered new interface driver asix <6>[ 4.744491] usbcore: registered new interface driver ax88179_178a <6>[ 4.750936] usbcore: registered new interface driver cdc_ether <6>[ 4.757123] usbcore: registered new interface driver smsc75xx <6>[ 4.763194] usbcore: registered new interface driver smsc95xx <6>[ 4.769295] usbcore: registered new interface driver net1080 <6>[ 4.775270] usbcore: registered new interface driver cdc_subset <6>[ 4.781526] usbcore: registered new interface driver zaurus <6>[ 4.787469] usbcore: registered new interface driver cdc_ncm <6>[ 4.799016] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.805853] ehci-pci: EHCI PCI platform driver <6>[ 4.810700] ehci-platform: EHCI generic platform driver <6>[ 4.816752] ehci-orion: EHCI orion driver <6>[ 4.821430] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.826028] ehci-st: EHCI STMicroelectronics driver <6>[ 4.831559] ehci-exynos: EHCI Exynos driver <6>[ 4.836319] ehci-atmel: EHCI Atmel driver <6>[ 4.840974] tegra-ehci: Tegra EHCI driver <6>[ 4.845607] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.852177] ohci-pci: OHCI PCI platform driver <6>[ 4.857003] ohci-platform: OHCI generic platform driver <6>[ 4.862957] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.867649] ohci-st: OHCI STMicroelectronics driver <6>[ 4.873121] ohci-atmel: OHCI Atmel driver <6>[ 4.879414] usbcore: registered new interface driver usb-storage <6>[ 4.896519] i2c /dev entries driver <5>[ 4.928724] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.937045] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.943528] sdhci: Copyright(c) Pierre Ossman <6>[ 4.952522] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.961886] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.976492] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.011250] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.020804] usbcore: registered new interface driver usbhid <6>[ 5.026804] usbhid: USB HID core driver <6>[ 5.040338] NET: Registered protocol family 10 <6>[ 5.046576] Segment Routing with IPv6 <6>[ 5.050705] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.057711] NET: Registered protocol family 17 <6>[ 5.062459] can: controller area network core <6>[ 5.067258] NET: Registered protocol family 29 <6>[ 5.071988] can: raw protocol <6>[ 5.075232] can: broadcast manager protocol <6>[ 5.079731] can: netlink gateway - max_hops=1 <5>[ 5.085149] Key type dns_resolver registered <6>[ 5.089923] ThumbEE CPU extension supported. <5>[ 5.094492] Registering SWP/SWPB emulation handler <3>[ 5.100047] omap_voltage_late_init: Voltage driver support not added <6>[ 5.108288] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 5.117199] Loading compiled-in X.509 certificates <6>[ 5.138535] OMAP GPIO hardware version 0.1 <4>[ 5.167371] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 5.180480] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 5.195560] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <4>[ 5.201958] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 5.209351] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 5.217343] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <4>[ 5.227039] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 5.241222] mmc1: new high speed MMC card at address 0001 <6>[ 5.247827] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 5.252977] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.259736] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.266238] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 5.275746] mmcblk1: p1 <4>[ 5.279918] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 5.321041] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 5.360714] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 5.399731] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 5.423361] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 5.432556] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 5.437687] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.500819] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.542913] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.628599] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 8.757621] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 8.766885] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.796887] Sending DHCP requests ., OK <6>[ 8.840994] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 8.849146] IP-Config: Complete: <6>[ 8.852687] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 8.863273] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 8.870342] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.870362] nameserver0=192.168.11.1 <6>[ 8.894656] Freeing unused kernel memory: 2048K <6>[ 8.917962] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.119752] udevd[97]: starting version 3.2.9 <27>[ 9.135728] udevd[97]: specified user 'tss' unknown <27>[ 9.141537] udevd[97]: specified group 'tss' unknown <30>[ 9.158869] udevd[98]: starting eudev-3.2.9 <4>[ 10.815628] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 10.824785] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 11.118152] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.127238] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 11.284372] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 11.290201] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 11.528015] hub 1-0:1.0: USB hub found <6>[ 11.605960] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1018657/environment . /lava-1018657/environment / # /lava-1018657/bin/lava-test-runner /lava-1018657/0 /lava-1018657/bin/lava-test-runner /lava-1018657/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1018657/0/tests/0_dmesg + cat uuid + UUID=1018657_1.5.2.4.1 + <8>[ 16.331390] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.388019] <8>[ 16.439381] <8>[ 16.490876] + set +x <8>[ 16.501707] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1018657/environment / # . /lava-1018657/environment/lava-1018657/bin/lava-test-runner /lava-1018657/1 / # /lava-1018657/bin/lava-test-runner /lava-1018657/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1018657/1/tests/1_bootrr + cat uuid + UUID=1018657_1.5.2.4.5 + <8>[ 17.023204] set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1018657/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound /lava-1018657/1/../bin/lava-test-case <8>[ 18.115771] /lava-1018657/1/../bin/lava-test-case <8>[ 18.164779] /lava-1018657/1/../bin/lava-test-case <8>[ 18.194553] /lava-1018657/1/../bin/lava-test-case <8>[ 18.249512] /lava-1018657/1/../bin/lava-test-case <8>[ 18.295725] /lava-1018657/1/../bin/lava-test-case <8>[ 18.332657] /lava-1018657/1/../bin/lava-test-case <8>[ 18.378770] /lava-1018657/1/../bin/lava-test-case <8>[ 18.423637] /lava-1018657/1/../bin/lava-test-case <8>[ 18.460217] /lava-1018657/1/../bin/lava-test-case <8>[ 18.505906] /lava-1018657/1/../bin/lava-test-case <8>[ 19.567095] /lava-1018657/1/../bin/lava-test-case <8>[ 20.628221] /lava-1018657/1/../bin/lava-test-case <8>[ 20.666480] /lava-1018657/1/../bin/lava-test-case <8>[ 20.702494] /lava-1018657/1/../bin/lava-test-case <8>[ 20.739530] /lava-1018657/1/../bin/lava-test-case <8>[ 20.784418] /lava-1018657/1/../bin/lava-test-case <8>[ 20.822330] /lava-1018657/1/../bin/lava-test-case <8>[ 20.868719] /lava-1018657/1/../bin/lava-test-case <8>[ 20.913706] /lava-1018657/1/../bin/lava-test-case <8>[ 20.950489] /lava-1018657/1/../bin/lava-test-case <8>[ 20.996338] /lava-1018657/1/../bin/lava-test-case <8>[ 21.042330] /lava-1018657/1/../bin/lava-test-case <8>[ 21.079923] /lava-1018657/1/../bin/lava-test-case <8>[ 21.125699] /lava-1018657/1/../bin/lava-test-case <8>[ 21.163134] /lava-1018657/1/../bin/lava-test-case <8>[ 21.208888] /lava-1018657/1/../bin/lava-test-case <8>[ 22.273176] /lava-1018657/1/../bin/lava-test-case <8>[ 23.335572] /lava-1018657/1/../bin/lava-test-case <8>[ 23.373096] /lava-1018657/1/../bin/lava-test-case <8>[ 23.419784] /lava-1018657/1/../bin/lava-test-case <8>[ 23.457307] /lava-1018657/1/../bin/lava-test-case <8>[ 23.502646] /lava-1018657/1/../bin/lava-test-case <8>[ 24.564639] /lava-1018657/1/../bin/lava-test-case <8>[ 25.626087] /lava-1018657/1/../bin/lava-test-case <8>[ 25.662818] /lava-1018657/1/../bin/lava-test-case <8>[ 25.708844] /lava-1018657/1/../bin/lava-test-case <8>[ 26.773105] /lava-1018657/1/../bin/lava-test-case <8>[ 27.835091] /lava-1018657/1/../bin/lava-test-case <8>[ 28.896025] /lava-1018657/1/../bin/lava-test-case <8>[ 29.957231] /lava-1018657/1/../bin/lava-test-case <8>[ 31.017238] /lava-1018657/1/../bin/lava-test-case <8>[ 32.082862] /lava-1018657/1/../bin/lava-test-case <8>[ 33.137888] /lava-1018657/1/../bin/lava-test-case <8>[ 34.204168] /lava-1018657/1/../bin/lava-test-case <8>[ 35.265647] /lava-1018657/1/../bin/lava-test-case <8>[ 36.326224] /lava-1018657/1/../bin/lava-test-case <8>[ 37.386489] /lava-1018657/1/../bin/lava-test-case <8>[ 38.447347] /lava-1018657/1/../bin/lava-test-case <8>[ 39.512141] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-1018657/1/../bin/lava-test-case <8>[ 39.550677] /lava-1018657/1/../bin/lava-test-case <8>[ 40.623063] /lava-1018657/1/../bin/lava-test-case <8>[ 41.684200] + set +x <8>[ 41.699696] / #