[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (10 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11723606/tftp-deploy-371slkcg/kernel/zImage tftp 0x10000000 11723606/tftp-deploy-371slkcg/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11723606/tftp-deploy-371slkcg/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 5.8 MiB/s done Bytes transferred = 9708032 (942200 hex) => tftp 0x14000000 11723606/tftp-deploy-371slkcg/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11723606/tftp-deploy-371slkcg/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11723606/tftp-deploy-371slkcg/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 14.3 MiB/s done Bytes transferred = 12150059 (b9652b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11723606/tftp-deploy-371slkcg/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11723606/tftp-deploy-371slkcg/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11723606/tftp-deploy-371slkcg/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11723606/extract-nfsrootfs-4y03bfzm,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11723606/extract-nfsrootfs-4y03bfzm,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x942200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12149995 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.197-cip39 (KernelCI@build-j68479-arm-gcc-10-multi-v7-defconfig-b5mv2) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Oct 10 10:01:49 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11723606/extract-nfsrootfs-4y03bfzm,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936488K/1048576K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 46552K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022224] Console: colour dummy device 80x30 <6>[ 0.024117] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034523] CPU: Testing write buffer coherency: ok <6>[ 0.039657] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044955] pid_max: default: 32768 minimum: 301 <6>[ 0.049984] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057418] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066292] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072028] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079728] rcu: Hierarchical SRCU implementation. <6>[ 0.086721] EFI services will not be available. <6>[ 0.088953] smp: Bringing up secondary CPUs ... <6>[ 0.094253] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094261] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105587] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105595] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116808] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116816] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127240] smp: Brought up 1 node, 4 CPUs <6>[ 0.131464] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137923] CPU: All CPU(s) started in SVC mode. <6>[ 0.143345] devtmpfs: initialized <6>[ 0.153787] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159138] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169000] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179216] pinctrl core: initialized pinctrl subsystem <6>[ 0.183685] DMI not present or invalid. <6>[ 0.186793] NET: Registered protocol family 16 <6>[ 0.194064] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200714] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200904] cpuidle: using governor menu <6>[ 0.208999] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.383403] vdd1p1: supplied by regulator-dummy <6>[ 0.392364] vdd3p0: supplied by regulator-dummy <6>[ 0.401217] vdd2p5: supplied by regulator-dummy <6>[ 0.410108] vddarm: supplied by regulator-dummy <6>[ 0.419120] vddpu: supplied by regulator-dummy <6>[ 0.427750] vddsoc: supplied by regulator-dummy <6>[ 0.748317] No ATAGs? <6>[ 0.748508] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.756280] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.766458] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.776675] Serial: AMBA PL011 UART driver <6>[ 0.780793] printk: console [ramoops-1] enabled <6>[ 0.783178] pstore: Registered ramoops as persistent store backend <6>[ 0.789428] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.827091] iommu: Default domain type: Translated <6>[ 0.829857] vgaarb: loaded <5>[ 0.833202] SCSI subsystem initialized <6>[ 0.836939] usbcore: registered new interface driver usbfs <6>[ 0.842125] usbcore: registered new interface driver hub <6>[ 0.847713] usbcore: registered new device driver usb <6>[ 0.854523] i2c i2c-0: IMX I2C adapter registered <6>[ 0.859254] i2c i2c-1: IMX I2C adapter registered <6>[ 0.863693] i2c i2c-2: IMX I2C adapter registered <6>[ 0.869214] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.873054] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.882482] PTP clock support registered <6>[ 0.890228] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.004465] NET: Registered protocol family 2 <6>[ 2.006667] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.015091] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.022561] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.030604] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.038036] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.044756] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.051464] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.058873] NET: Registered protocol family 1 <6>[ 2.063953] RPC: Registered named UNIX socket transport module. <6>[ 2.069486] RPC: Registered udp transport module. <6>[ 2.074478] RPC: Registered tcp transport module. <6>[ 2.079401] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.086128] PCI: CLS 0 bytes, default 64 <6>[ 2.090792] Trying to unpack rootfs image as initramfs... <6>[ 3.054187] Freeing initrd memory: 11868K <4>[ 3.056087] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.063470] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.073273] Initialise system trusted keyrings <6>[ 3.076374] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.088718] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.092743] NFS: Registering the id_resolver key type <5>[ 3.097343] Key type id_resolver registered <5>[ 3.101730] Key type id_legacy registered <6>[ 3.106090] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.112963] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.120653] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.125703] Key type asymmetric registered <5>[ 3.129549] Asymmetric key parser 'x509' registered <6>[ 3.134754] bounce: pool size: 64 pages <6>[ 3.138803] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.146445] io scheduler mq-deadline registered <6>[ 3.151227] io scheduler kyber registered <6>[ 3.194823] mxs-dma 110000.dma-controller: initialized <4>[ 3.202194] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.209974] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.264928] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.273109] SuperH (H)SCI(F) driver initialized <6>[ 3.276038] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.284961] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.292855] printk: console [ttymxc1] enabled <6>[ 3.292855] printk: console [ttymxc1] enabled <6>[ 3.302029] printk: bootconsole [ec_imx21] disabled <6>[ 3.302029] printk: bootconsole [ec_imx21] disabled <6>[ 3.313706] msm_serial: driver initialized <6>[ 3.319721] STMicroelectronics ASC driver initialized <6>[ 3.327023] STM32 USART driver initialized <4>[ 3.341816] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.349729] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.356575] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.373234] brd: module loaded <6>[ 3.384049] loop: module loaded <6>[ 3.391401] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.399595] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.407888] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.416352] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.424360] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.432131] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.439681] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.450288] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.457543] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.466643] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.477467] scsi host0: ahci-imx <6>[ 3.481370] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.501835] CAN device driver interface <6>[ 3.507276] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.516804] pps pps0: new PPS source ptp0 <6>[ 3.538995] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.546614] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.551871] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.558120] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.563802] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.575793] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.583528] usbcore: registered new interface driver pegasus <6>[ 3.589497] usbcore: registered new interface driver asix <6>[ 3.595218] usbcore: registered new interface driver ax88179_178a <6>[ 3.601626] usbcore: registered new interface driver cdc_ether <6>[ 3.607773] usbcore: registered new interface driver smsc75xx <6>[ 3.613855] usbcore: registered new interface driver smsc95xx <6>[ 3.619905] usbcore: registered new interface driver net1080 <6>[ 3.625883] usbcore: registered new interface driver cdc_subset <6>[ 3.632116] usbcore: registered new interface driver zaurus <6>[ 3.638028] usbcore: registered new interface driver cdc_ncm <6>[ 3.647520] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.654341] ehci-pci: EHCI PCI platform driver <6>[ 3.659090] ehci-platform: EHCI generic platform driver <6>[ 3.664902] ehci-orion: EHCI orion driver <6>[ 3.669402] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.673887] ehci-st: EHCI STMicroelectronics driver <6>[ 3.679218] ehci-exynos: EHCI Exynos driver <6>[ 3.683865] ehci-atmel: EHCI Atmel driver <6>[ 3.688316] tegra-ehci: Tegra EHCI driver <6>[ 3.692843] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.699308] ohci-pci: OHCI PCI platform driver <6>[ 3.704090] ohci-platform: OHCI generic platform driver <6>[ 3.709842] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.714337] ohci-st: OHCI STMicroelectronics driver <6>[ 3.719673] ohci-atmel: OHCI Atmel driver <6>[ 3.725222] usbcore: registered new interface driver usb-storage <6>[ 3.739689] i2c /dev entries driver <6>[ 3.763090] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.769542] sdhci: Copyright(c) Pierre Ossman <6>[ 3.776916] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.785154] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.792359] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.796538] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.797646] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.808417] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.815767] usbcore: registered new interface driver usbhid <6>[ 3.821630] usbhid: USB HID core driver <6>[ 3.832277] NET: Registered protocol family 10 <6>[ 3.835061] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.837996] Segment Routing with IPv6 <6>[ 3.839639] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.840117] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.842725] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.846686] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.853769] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.861525] NET: Registered protocol family 17 <6>[ 3.875279] mmc2: new high speed SDHC card at address 0001 <6>[ 3.881074] can: controller area network core <6>[ 3.886632] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 3.891635] NET: Registered protocol family 29 <6>[ 3.905383] can: raw protocol <6>[ 3.908628] can: broadcast manager protocol <4>[ 3.912392] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 3.913110] can: netlink gateway - max_hops=1 <4>[ 3.920764] GPT:7812499 != 30560255 <5>[ 3.925889] Key type dns_resolver registered <4>[ 3.929133] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.939951] GPT:7812499 != 30560255 <6>[ 3.941944] ThumbEE CPU extension supported. <4>[ 3.943728] GPT: Use GNU Parted to correct GPT errors. <5>[ 3.948251] Registering SWP/SWPB emulation handler <6>[ 3.953704] mmcblk2: p1 p2 p3 <5>[ 3.959024] Loading compiled-in X.509 certificates <6>[ 3.972711] pstore: Using crash dump compression: deflate <4>[ 3.999905] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.007831] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.015799] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.031833] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.041822] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.047012] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.080342] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.087464] hub 1-0:1.0: USB hub found <6>[ 4.091608] hub 1-0:1.0: 1 port detected <6>[ 4.100254] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.115475] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.123418] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.131331] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.143430] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.151345] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.159153] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.169140] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.181384] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.189260] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.197186] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.211321] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.420275] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.621937] hub 1-1:1.0: USB hub found <6>[ 4.626151] hub 1-1:1.0: 3 ports detected <4>[ 4.636701] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.644677] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.652930] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.360693] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.370288] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.400360] Sending DHCP requests ., OK <6>[ 7.444429] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 <6>[ 7.452781] IP-Config: Complete: <6>[ 7.456305] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.467051] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) <6>[ 7.475197] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.475211] nameserver0=192.168.201.1 <6>[ 7.494075] Freeing unused kernel memory: 2048K <6>[ 7.520719] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 8.400038] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.407202] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.418853] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.426843] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.452404] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.476709] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.500325] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.508765] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.535666] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.543658] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.569724] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.580384] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.592267] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.599104] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.606325] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.613448] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.613565] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.619851] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.633086] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 8.641822] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.664058] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.671040] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.672010] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.680396] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.686000] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.700803] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.709369] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.746773] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.752233] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <4>[ 8.752485] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.759129] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.786712] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.795353] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.798393] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.803930] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.811983] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 8.820342] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.828884] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.839169] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.845321] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 8.853090] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.869979] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.878257] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.893661] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.902230] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.910827] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.919366] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.931050] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.939056] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.940605] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.999458] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.016802] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.025434] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.034103] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.042658] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.052991] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.061044] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.267728] caam algorithms registered in /proc/crypto <6>[ 9.274598] caam 2100000.crypto: registering rng-caam <4>[ 9.281543] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.296065] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers <6>[ 9.304628] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) ... <6>[ 9.315899] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done. <6>[ 9.324703] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top<4>[ 9.343650] panel-simple panel-lcd: supply power not found, using dummy regulator ... done. Begin: Running /scrip<4>[ 9.351862] panel-simple panel-lcd: Specify missing connector_type ts/nfs-premount ... Waiting up to<4>[ 9.363357] panel-simple panel-lvds0: supply power not found, using dummy regulator 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. <5>[ 9.462343] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.333046] systemd[1]: System time before build time, advancing clock. <30>[ 10.379852] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.404196] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.442790] systemd[1]: Set hostname to . <30>[ 11.209571] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.219245] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.232068] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.241693] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.281552] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.320922] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.361327] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.401003] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.440601] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.480947] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.493594] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.531075] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.560719] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.600609] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.630704] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.661572] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.736374] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.746658] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.781793] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.822116] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.863954] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 11.901666] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 11.940929] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.949924] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.962472] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 12.004488] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 12.048366] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 12.097169] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 12.134106] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 12.175193] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.212885] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.226481] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.268365] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.303990] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.343650] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.395490] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.430879] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.481296] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.551641] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 12.856601] systemd-journald[279]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.197-cip39 #1 SMP Tue Oct 10 10:01:49 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11723606/extract-nfsrootfs-4y03bfzm' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11723606/extract-nfsrootfs-4y03bfzm' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-11723606/environment . /lava-11723606/environment / # /lava-11723606/bin/lava-test-runner /lava-11723606/0 /lava-11723606/bin/lava-test-runner /lava-11723606/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-11723606/0/tests/0_timesync-off ++ cat uuid + UUID=11723606_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-11723606/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=11723606_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.194-cip39-552-gc89b2c57483f0/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-10-10 10:28:10-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.194-cip39-552-gc89b2c57483f0/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1408948 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 41.67K 108KB/s kselftest.tar.xz 8%[> ] 120.85K 189KB/s kselftest.tar.xz 13%[=> ] 184.49K 180KB/s kselftest.tar.xz 17%[==> ] 238.71K 186KB/s kselftest.tar.xz 20%[===> ] 282.54K 184KB/s kselftest.tar.xz 23%[===> ] 324.96K 181KB/s kselftest.tar.xz 26%[====> ] 365.97K 179KB/s kselftest.tar.xz 29%[====> ] 408.39K 177KB/s kselftest.tar.xz 32%[=====> ] 453.64K 177KB/s kselftest.tar.xz 36%[======> ] 504.55K 179KB/s kselftest.tar.xz 40%[=======> ] 556.87K 181KB/s eta 5s kselftest.tar.xz 43%[=======> ] 600.71K 180KB/s eta 5s kselftest.tar.xz 46%[========> ] 633.23K 176KB/s eta 5s kselftest.tar.xz 48%[========> ] 661.51K 172KB/s eta 5s kselftest.tar.xz 50%[=========> ] 695.45K 169KB/s eta 4s kselftest.tar.xz 51%[=========> ] 713.35K 164KB/s eta 4s kselftest.tar.xz 54%[=========> ] 750.11K 158KB/s eta 4s kselftest.tar.xz 56%[==========> ] 771.81K 155KB/s eta 4s kselftest.tar.xz 57%[==========> ] 784.53K 155KB/s eta 4s kselftest.tar.xz 58%[==========> ] 805.75K 143KB/s eta 4s kselftest.tar.xz 60%[===========> ] 829.78K 134KB/s eta 4s kselftest.tar.xz 62%[===========> ] 856.65K 130KB/s eta 4s kselftest.tar.xz 64%[===========> ] 886.35K 127KB/s eta 3s kselftest.tar.xz 66%[============> ] 919.80K 120KB/s eta 3s kselftest.tar.xz 69%[============> ] 949.98K 118KB/s eta 3s kselftest.tar.xz 70%[=============> ] 974.95K 104KB/s eta 3s kselftest.tar.xz 72%[=============> ] 1002K 99.7KB/s eta 3s kselftest.tar.xz 74%[=============> ] 1019K 96.7KB/s eta 3s kselftest.tar.xz 75%[==============> ] 1.01M 94.4KB/s eta 3s kselftest.tar.xz 76%[==============> ] 1.03M 92.0KB/s eta 3s kselftest.tar.xz 78%[==============> ] 1.05M 89.6KB/s eta 3s kselftest.tar.xz 79%[==============> ] 1.07M 92.9KB/s eta 2s kselftest.tar.xz 81%[===============> ] 1.09M 92.1KB/s eta 2s kselftest.tar.xz 83%[===============> ] 1.12M 93.5KB/s eta 2s kselftest.tar.xz 85%[================> ] 1.14M 94.8KB/s eta 2s kselftest.tar.xz 86%[================> ] 1.17M 97.4KB/s eta 2s kselftest.tar.xz 88%[================> ] 1.19M 98.0KB/s eta 1s kselftest.tar.xz 90%[=================> ] 1.22M 98.8KB/s eta 1s kselftest.tar.xz 92%[=================> ] 1.24M 100KB/s eta 1s kselftest.tar.xz 94%[=================> ] 1.28M 100KB/s eta 1s kselftest.tar.xz 97%[==================> ] 1.31M 102KB/s eta 1s kselftest.tar.xz 99%[==================> ] 1.34M 110KB/s eta 0s kselftest.tar.xz 100%[===================>] 1.34M 105KB/s in 11s 2023-10-10 10:28:22 (126 KB/s) - 'kselftest.tar.xz' saved [1408948/1408948] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== shardfile-filesystems pass <12>[ 42.650432] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #