Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.91 (255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 396930/tftp-deploy-x4tfpijm/kernel/Image tftp 0x82000000 396930/tftp-deploy-x4tfpijm/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '396930/tftp-deploy-x4tfpijm/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 16.9 MiB/s done Bytes transferred = 31855104 (1e61200 hex) => tftp 0x90080000 396930/tftp-deploy-x4tfpijm/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 396930/tftp-deploy-x4tfpijm/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '396930/tftp-deploy-x4tfpijm/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### 16.2 MiB/s done Bytes transferred = 15328983 (e9e6d7 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 396930/tftp-deploy-x4tfpijm/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 396930/tftp-deploy-x4tfpijm/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '396930/tftp-deploy-x4tfpijm/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 4.8 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/396930/extract-nfsrootfs-dmqxyj_6,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/396930/extract-nfsrootfs-dmqxyj_6,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2023-11-20 10:15:21 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15328919 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.200-cip40-rt17 (KernelCI@build-j18970-arm64-gcc-10-defconfig-rpn9x) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Mon Nov 20 09:47:53 UTC 2023 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7feb00-0x20ff800fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0 totalpages: 1031680 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 507392 pages, LIFO batch:63 [ 0.000000] Normal zone: 8192 pages used for memmap [ 0.000000] Normal zone: 524288 pages, LIFO batch:63 [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 19 pages/cpu s40408 r8192 d29224 u77824 [ 0.000000] pcpu-alloc: s40408 r8192 d29224 u77824 alloc=19*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/nfs rw nfsroot=10.228.65.1:/var/lib/lava/dispatcher/tmp/396930/extract-nfsrootfs-dmqxyj_6,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3901288K/4126720K available (14528K kernel code, 2884K rwdata, 7656K rodata, 5952K init, 504K bss, 192664K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008715] Console: colour dummy device 80x25 <6>[ 0.013506] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024223] pid_max: default: 32768 minimum: 301 <6>[ 0.029180] LSM: Security Framework initializing <6>[ 0.034145] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041900] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050946] rcu: Hierarchical SRCU implementation. <6>[ 0.056185] Platform MSI: gic-its@6020000 domain created <6>[ 0.061876] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069737] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075855] EFI services will not be available. <6>[ 0.080794] smp: Bringing up secondary CPUs ... <6>[ 0.085889] Detected PIPT I-cache on CPU1 <6>[ 0.090210] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.097416] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.104988] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.111895] smp: Brought up 1 node, 2 CPUs <6>[ 0.116304] SMP: Total of 2 processors activated. <6>[ 0.121316] CPU features: detected: 32-bit EL0 Support <6>[ 0.126773] CPU features: detected: CRC32 instructions <6>[ 0.132224] CPU features: detected: 32-bit EL1 Support <6>[ 0.148810] CPU: All CPU(s) started at EL2 <6>[ 0.153227] alternatives: patching kernel code <6>[ 0.158706] devtmpfs: initialized <4>[ 0.164385] KASLR disabled due to lack of seed <6>[ 0.169244] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.179354] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.187032] pinctrl core: initialized pinctrl subsystem <6>[ 0.193189] DMI not present or invalid. <6>[ 0.197704] NET: Registered protocol family 16 <6>[ 0.203226] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210720] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218966] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.227242] audit: initializing netlink subsys (disabled) <5>[ 0.233076] audit: type=2000 audit(0.156:1): state=initialized audit_enabled=0 res=1 <6>[ 0.233594] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.233597] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.241166] cpuidle: using governor menu <6>[ 0.258668] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.265808] ASID allocator initialised with 65536 entries <6>[ 0.272182] Serial: AMBA PL011 UART driver <6>[ 0.287261] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.294912] SoC family: QorIQ LS1028A <6>[ 0.298864] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.311358] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.318402] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.325432] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.332463] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.340257] cryptd: max_cpu_qlen set to 1000 <6>[ 0.346251] ACPI: Interpreter disabled. <6>[ 0.351350] iommu: Default domain type: Translated <6>[ 0.356724] vgaarb: loaded <5>[ 0.359854] SCSI subsystem initialized <7>[ 0.363985] libata version 3.00 loaded. <6>[ 0.368228] usbcore: registered new interface driver usbfs <6>[ 0.374175] usbcore: registered new interface driver hub <6>[ 0.379820] usbcore: registered new device driver usb <6>[ 0.385438] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.393377] i2c i2c-0: IMX I2C adapter registered <6>[ 0.398561] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.406248] i2c i2c-1: IMX I2C adapter registered <6>[ 0.411335] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.419110] i2c i2c-2: IMX I2C adapter registered <6>[ 0.424389] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.429671] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.439162] PTP clock support registered <6>[ 0.443446] EDAC MC: Ver: 3.0.0 <6>[ 0.447599] FPGA manager framework <6>[ 0.451335] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.458160] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.464676] VFS: Disk quotas dquot_6.6.0 <6>[ 0.468935] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.476237] pnp: PnP ACPI: disabled <6>[ 0.483249] NET: Registered protocol family 2 <6>[ 0.488205] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.497254] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.506183] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.514531] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.522532] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.529492] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.536546] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.544108] NET: Registered protocol family 1 <6>[ 0.549093] RPC: Registered named UNIX socket transport module. <6>[ 0.555338] RPC: Registered udp transport module. <6>[ 0.560348] RPC: Registered tcp transport module. <6>[ 0.565356] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.572124] PCI: CLS 0 bytes, default 64 <6>[ 0.576434] Unpacking initramfs... <6>[ 1.081539] Freeing initrd memory: 14964K <6>[ 1.086213] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.094908] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.100066] kvm [1]: GICv3: no GICV resource entry <6>[ 1.105169] kvm [1]: disabling GICv2 emulation <6>[ 1.109930] kvm [1]: GIC system register CPU interface enabled <6>[ 1.116115] kvm [1]: vgic interrupt IRQ9 <6>[ 1.120402] kvm [1]: Hyp mode initialized successfully <5>[ 1.126837] Initialise system trusted keyrings <6>[ 1.131683] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.141556] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.148081] NFS: Registering the id_resolver key type <5>[ 1.153464] Key type id_resolver registered <5>[ 1.157951] Key type id_legacy registered <6>[ 1.162307] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.169341] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.177166] 9p: Installing v9fs 9p2000 file system support <5>[ 1.212469] Key type asymmetric registered <5>[ 1.216870] Asymmetric key parser 'x509' registered <6>[ 1.222076] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.229809] io scheduler mq-deadline registered <6>[ 1.234647] io scheduler kyber registered <6>[ 1.243930] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.252046] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 1.261195] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 1.270344] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 1.279490] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 1.288635] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 1.297781] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 1.306928] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 1.316113] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.325229] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.332524] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.338063] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 1.348780] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 1.359943] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.370662] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.381816] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.392532] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.403686] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 1.414415] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.420773] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.431583] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.442827] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.453894] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.465413] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.471222] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.481500] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.492370] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.498722] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.509528] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.520770] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.531838] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.543355] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.549161] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.559442] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.570275] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.576629] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.587434] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.598688] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.604600] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.610954] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.621762] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.633016] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.638924] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.645274] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.656078] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.667331] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.673241] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.679594] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.690400] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.701642] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.712456] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.718368] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.724717] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.735522] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.746778] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.753395] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.759758] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.767722] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <3>[ 1.775734] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-22 <6>[ 1.783047] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.790714] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.799595] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.808562] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 1.815594] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 1.821395] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 1.827899] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.838803] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.845182] pci 0001:00:00.0: supports D1 D2 <6>[ 1.849755] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.857553] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.864505] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 1.869925] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 1.877591] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 1.886471] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 1.895426] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 1.902458] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 1.908260] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 1.917572] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.928492] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.934872] pci 0002:00:00.0: supports D1 D2 <6>[ 1.939445] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.947238] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.954187] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 1.960197] EINJ: ACPI disabled. <6>[ 1.971541] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.979530] printk: console [ttyS0] disabled <6>[ 1.984151] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.993356] printk: console [ttyS0] enabled <6>[ 1.993356] printk: console [ttyS0] enabled <6>[ 2.002297] printk: bootconsole [ns16550a0] disabled <6>[ 2.002297] printk: bootconsole [ns16550a0] disabled <6>[ 2.013128] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.022508] SuperH (H)SCI(F) driver initialized <6>[ 2.027614] msm_serial: driver initialized <6>[ 2.032341] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 2.042934] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 2.049675] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 2.054573] arm-smmu 5000000.iommu: stage 1 translation <5>[ 2.060165] arm-smmu 5000000.iommu: stage 2 translation <5>[ 2.065757] arm-smmu 5000000.iommu: nested translation <5>[ 2.071265] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 2.078691] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 2.085512] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 2.092239] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 2.098964] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 2.108978] loop: module loaded <6>[ 2.117623] megasas: 07.714.04.00-rc1 <6>[ 2.123652] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 2.135112] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 2.144200] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 2.151289] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 2.156800] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 2.166514] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 2.174486] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 2.182494] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 2.190497] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 2.198477] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 2.206490] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 2.214492] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 2.224232] tun: Universal TUN/TAP device driver, 1.6 <6>[ 2.230034] thunder_xcv, ver 1.0 <6>[ 2.233561] thunder_bgx, ver 1.0 <6>[ 2.237084] nicpf, ver 1.0 <6>[ 2.240573] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 2.354176] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 2.360689] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 52:c6:3e:82:d6:73 <6>[ 2.369517] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 62:1f:93:5e:f4:e7 <6>[ 2.384871] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 2.498170] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.505556] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.511927] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 2.622172] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.628982] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.635344] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 2.746171] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.752972] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.759393] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 2.870172] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 2.877346] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 2.883635] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 2.890558] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 2.899563] pps pps0: new PPS source ptp0 <6>[ 2.904299] hclge is initializing <6>[ 2.907900] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 2.915413] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 2.921053] e1000: Intel(R) PRO/1000 Network Driver <6>[ 2.926211] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 2.932269] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.937513] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.943747] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.949426] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.955298] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.961849] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.968251] sky2: driver version 1.30 <6>[ 2.972834] VFIO - User Level meta-driver version: 0.3 <6>[ 2.978584] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 3.042525] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 3.107293] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.114130] ehci-pci: EHCI PCI platform driver <6>[ 3.118874] ehci-platform: EHCI generic platform driver <6>[ 3.124453] ehci-orion: EHCI orion driver <6>[ 3.128794] ehci-exynos: EHCI Exynos driver <6>[ 3.133303] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.139777] ohci-pci: OHCI PCI platform driver <6>[ 3.144520] ohci-platform: OHCI generic platform driver <6>[ 3.150093] ohci-exynos: OHCI Exynos driver <6>[ 3.154769] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.160548] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 3.168640] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.178357] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 3.184649] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.190420] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 3.198373] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.205495] hub 1-0:1.0: USB hub found <6>[ 3.209538] hub 1-0:1.0: 1 port detected <6>[ 3.213906] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.222517] hub 2-0:1.0: USB hub found <6>[ 3.226555] hub 2-0:1.0: 1 port detected <6>[ 3.230944] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.236730] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 3.244813] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.254530] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 3.260819] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.266590] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 3.274542] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.281613] hub 3-0:1.0: USB hub found <6>[ 3.285650] hub 3-0:1.0: 1 port detected <6>[ 3.290006] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.298620] hub 4-0:1.0: USB hub found <6>[ 3.302660] hub 4-0:1.0: 1 port detected <6>[ 3.307285] usbcore: registered new interface driver usb-storage <6>[ 3.315241] i2c /dev entries driver <6>[ 3.321867] sp805-wdt c000000.watchdog: registration successful <6>[ 3.328189] sp805-wdt c010000.watchdog: registration successful <6>[ 3.335617] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 3.344381] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.350870] sdhci: Copyright(c) Pierre Ossman <6>[ 3.355836] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.362713] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.369148] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 3.369732] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 3.381057] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.388323] usbcore: registered new interface driver usbhid <6>[ 3.394202] usbhid: USB HID core driver <6>[ 3.399887] mmc0: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 3.401106] NET: Registered protocol family 17 <6>[ 3.407103] mmc1: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 3.411971] 9pnet: Installing 9P2000 support <5>[ 3.423566] Key type dns_resolver registered <6>[ 3.428382] printk: console [ttyS0]: printing thread started <6>[ 3.428417] registered taskstats version 1 <5>[ 3.428422] Loading compiled-in X.509 certificates <6>[ 3.430894] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 3.431966] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 3.432121] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 3.432252] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 3.432390] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 3.475396] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 3.539759] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 3.543501] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 3.560528] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 3.579216] mmc1: new HS400 MMC card at address 0001 <6>[ 3.579649] mmcblk1: mmc1:0001 S0J56X 7.34 GiB <6>[ 3.579849] mmcblk1boot0: mmc1:0001 S0J56X partition 1 31.5 MiB <6>[ 3.580071] mmcblk1boot1: mmc1:0001 S0J56X partition 2 31.5 MiB <6>[ 3.580182] mmcblk1rpmb: mmc1:0001 S0J56X partition 3 4.00 MiB, chardev (234:0) <6>[ 3.581324] mmcblk1: p1 p2 <6>[ 3.761729] hub 3-1:1.0: USB hub found <6>[ 3.761839] hub 3-1:1.0: 7 ports detected <6>[ 6.599133] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 6.630214] Sending DHCP requests ., OK <6>[ 6.646257] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.91 <6>[ 6.646281] IP-Config: Complete: <6>[ 6.646287] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.91, mask=255.255.255.0, gw=172.16.0.254 <6>[ 6.646311] host=172.16.0.91, domain=lava.lan, nis-domain=(none) <6>[ 6.646322] bootserver=0.0.0.0, rootserver=10.228.65.1, rootpath= <6>[ 6.646335] nameserver0=8.8.8.8 <6>[ 6.646873] ALSA device list: <6>[ 6.646890] No soundcards found. <6>[ 6.652216] Freeing unused kernel memory: 5952K Loading, please <6>[ 6.698284] Run /init as init process wait... Starting version 247.3-7+deb11u2 <6>[ 7.048315] mali-dp f080000.display: Adding to iommu group 13 <4>[ 7.078581] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 7.081445] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 7.081533] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 7.081562] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 7.081585] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 7.081623] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 7.087174] NET: Registered protocol family 10 <6>[ 7.088786] Segment Routing with IPv6 <6>[ 7.110320] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.111152] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 7.112051] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 7.112872] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 7.139503] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 7.139510] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 7.147275] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 7.148703] wm8904 2-001a: revision A <4>[ 7.152777] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 7.152880] rtc-rv8803 0-0032: registered as rtc0 <4>[ 7.156538] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 7.156554] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 7.157771] mscc_felix 0000:00:00.5: Adding to iommu group 14 <6>[ 7.160032] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 7.169133] mscc_felix 0000:00:00.5: device is disabled, skipping <6>[ 7.273850] caam 8000000.crypto: Entropy delay = 3200 <6>[ 7.293939] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 7.314008] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 7.314020] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 7.314025] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 7.376027] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 7.377089] caam algorithms registered in /proc/crypto <6>[ 7.378000] caam 8000000.crypto: registering rng-caam <6>[ 7.378375] caam_jr 8020000.jr: Adding to iommu group 16 Begin: Loading e<6>[ 7.384734] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 7.385197] caam_jr 8040000.jr: Adding to iommu group 18 ssential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. <5>[ 7.438331] random: crng init done IP-Config: eth0 hardware address 00:e0:4b:6e:9b:2b mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 172.16.0.255 IP-Config: eth0 complete (dhcp from 172.16.0.254): address: 172.16.0.91 broadcast: 172.16.0.255 netmask: 255.255.255.0 gateway: 172.16.0.254 dns0 : 8.8.8.8 dns1 : 0.0.0.0 domain : lava.lan rootserver: 172.16.0.254 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 7.757607] systemd[1]: System time before build time, advancing clock. <30>[ 7.806735] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 7.807627] systemd[1]: Detected architecture arm64. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 7.855478] systemd[1]: Set hostname to . [[0;32m OK [<30>[ 8.298853] systemd[1]: Queued start job for default target Graphical Interface. 0m] Created slic<28>[ 8.300032] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. e [0;1;39msyste<28>[ 8.300041] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 8.301425] systemd[1]: Created slice system-getty.slice. m-getty.slice[0m. [[0;32m OK [0m] Created slice [0;1;39msyste<30>[ 8.354898] systemd[1]: Created slice system-modprobe.slice. m-modprobe.slice[0m. [[0;32m OK [<30>[ 8.378946] systemd[1]: Created slice system-serial\x2dgetty.slice. 0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. [[0;32m OK [<30>[ 8.402751] systemd[1]: Created slice User and Session Slice. 0m] Created slice [0;1;39mUser and Session Slice[0m. [[0;32m OK [0m] Started [0;1;39mDispatch Pa<30>[ 8.430582] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. ssword …ts to Console Directory Watch[0m. [[0;32m OK [0m] Started [0;1;39mForward Pas<30>[ 8.454534] systemd[1]: Started Forward Password Requests to Wall Directory Watch. sword R…uests to Wall Directory Watch[0m. [[0;32m OK [0m] Reached target [0;1;39mLoca<30>[ 8.478400] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. l Encrypted Volu<30>[ 8.478542] systemd[1]: Reached target Local Encrypted Volumes. mes[0m. [[0;32m OK [<30>[ 8.514284] systemd[1]: Reached target Paths. 0m] Reached target [0;1;39mPaths[0m. [[0;32m OK [<30>[ 8.534236] systemd[1]: Reached target Remote File Systems. 0m] Reached target [0;1;39mRemote File Systems[0m. [[0;32m OK [<30>[ 8.554215] systemd[1]: Reached target Slices. 0m] Reached target [0;1;39mSlices[0m. [[0;32m OK [<30>[ 8.574288] systemd[1]: Reached target Swap. 0m] Reached target [0;1;39mSwap[0m. [[0;32m OK [0m] Listening on [0;1;39minitct<30>[ 8.594596] systemd[1]: Listening on initctl Compatibility Named Pipe. l Compatibility Named Pipe[0m. [[0;32m OK [0m] Listening on<30>[ 8.619642] systemd[1]: Listening on Journal Audit Socket. [0;1;39mJournal Audit Socket[0m. [[0;32m OK [0m] Listening on<30>[ 8.643412] systemd[1]: Listening on Journal Socket (/dev/log). [0;1;39mJournal Socket (/dev/log)[0m. [[0;32m OK [<30>[ 8.666861] systemd[1]: Listening on Journal Socket. 0m] Listening on [0;1;39mJournal Socket[0m. [[0;32m OK [0m] Listening on<30>[ 8.687653] systemd[1]: Listening on Network Service Netlink Socket. [0;1;39mNetwork Service Netlink Socket[0m. [[0;32m OK [<30>[ 8.717687] systemd[1]: Listening on udev Control Socket. 0m] Listening on [0;1;39mudev Control Socket[0m. [[0;32m OK [0m] Listening on<30>[ 8.739304] systemd[1]: Listening on udev Kernel Socket. [0;1;39mudev Kernel Socket[0m. Mounting [0;1;39mHuge <30>[ 8.768678] systemd[1]: Mounting Huge Pages File System... Pages File System[0m... Mountin<30>[ 8.792831] systemd[1]: Mounting POSIX Message Queue File System... g [0;1;39mPOSIX Message Queue File System[0m... Mountin<30>[ 8.817808] systemd[1]: Mounting Kernel Debug File System... g [0;1;39mKernel Debug File System[0m... Startin<30>[ 8.838688] systemd[1]: Condition check resulted in Kernel Trace File System being skipped. g [0;1;39mCreat<30>[ 8.842871] systemd[1]: Starting Create list of static device nodes for the current kernel... e list of st…odes for the current kernel[0m... Startin<30>[ 8.882134] systemd[1]: Starting Load Kernel Module configfs... g [0;1;39mLoad Kernel Module configfs[0m... Startin<30>[ 8.905823] systemd[1]: Starting Load Kernel Module drm... g [0;1;39mLoad Kernel Module drm[0m... Startin<30>[ 8.929925] systemd[1]: Starting Load Kernel Module fuse... g [0;1;39mLoad Kernel Module fuse[0m... <30>[ 8.951717] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. Startin<6>[ 8.951954] fuse: init (API version 7.32) g [0;1;39mJourn<30>[ 8.954529] systemd[1]: Starting Journal Service... al Service[0m... Startin<30>[ 8.994419] systemd[1]: Starting Load Kernel Modules... g [0;1;39mLoad Kernel Modules[0m... Starting [0;1;39mRemou<30>[ 9.016489] systemd[1]: Starting Remount Root and Kernel File Systems... nt Root and Kernel File Systems[0m... Starting [0;1;39mColdp<30>[ 9.040587] systemd[1]: Starting Coldplug All udev Devices... lug All udev Devices[0m... [[0;32m OK [<30>[ 9.065745] systemd[1]: Mounted Huge Pages File System. 0m] Mounted [0;1;39mHuge Pages File System[0m. [[0;32m OK [0m] Mounted [0;1;39mPOSIX Messa<30>[ 9.086616] systemd[1]: Mounted POSIX Message Queue File System. ge Queue File System[0m. [[0;32m OK [0m] Mounted [0;1;39mKernel Debu<30>[ 9.110621] systemd[1]: Mounted Kernel Debug File System. g File System[0m. [[0;32m OK [0m] Finished [0;1;39mCreate lis<30>[ 9.131066] systemd[1]: Finished Create list of static device nodes for the current kernel. t of st… nodes for the current kernel[0m. [[0;32m OK [0m] Started [0;1;39mJournal Ser<30>[ 9.158738] systemd[1]: Started Journal Service. vice[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. Mounting [0;1;39mFUSE Control File System[0m... Mounting [0;1;39mKernel Configuration File System[0m... Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mLoad/Save Random Seed[0m... Starting [0;1;39mApply Kernel Variables[0m... Starting [0;1;39mCreate System Users[0m... <46>[ 9.366571] systemd-journald[222]: Received client request to flush runtime journal. [[0;32m OK [0m] Mounted [0;1;39mFUSE Control File System[0m. [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mNetwork Time Synchronization[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Time Synchronization[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Set[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Synchronized[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [[0;32m OK [0m] Found device [0;1;39m/dev/ttyS0[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyS0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Runlevel Changes[0m. Debian GNU/Linux 11 debian-bullseye-arm64 ttyS0 debian-bullseye-arm64 login: root (automatic login) Linux debian-bullseye-arm64 5.10.200-cip40-rt17 #1 SMP PREEMPT Mon Nov 20 09:47:53 UTC 2023 aarch64 The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/396930/extract-nfsrootfs-dmqxyj_6' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/396930/extract-nfsrootfs-dmqxyj_6' / # export NFS_SERVER_IP='10.228.65.1' export NFS_SERVER_IP='10.228.65.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-396930/environment . /lava-396930/environment / # /lava-396930/bin/lava-test-runner /lava-396930/0 /lava-396930/bin/lava-test-runner /lava-396930/0 + export TESTRUN_ID=0_dmesg + cd /lava-396930/0/tests/0_dmesg + cat uuid + UUID=396930_1.6.2.4.1 + set +<8>[ 11.996588] x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.044448] <8>[ 12.089943] + set +x <8>[ 12.126637] [ 12.127170] R EXIT> / #