[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (11 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12195289/tftp-deploy-h_p4yptv/kernel/zImage tftp 0x10000000 12195289/tftp-deploy-h_p4yptv/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '12195289/tftp-deploy-h_p4yptv/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 5.8 MiB/s done Bytes transferred = 9708032 (942200 hex) => tftp 0x14000000 12195289/tftp-deploy-h_p4yptv/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12195289/tftp-deploy-h_p4yptv/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '12195289/tftp-deploy-h_p4yptv/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 14.1 MiB/s done Bytes transferred = 12151546 (b96afa hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12195289/tftp-deploy-h_p4yptv/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12195289/tftp-deploy-h_p4yptv/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '12195289/tftp-deploy-h_p4yptv/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12195289/extract-nfsrootfs-4xxupjky,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12195289/extract-nfsrootfs-4xxupjky,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x942200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12151482 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip41 (KernelCI@build-j36124-arm-gcc-10-multi-v7-defconfig-mmbfn) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Dec 6 06:16:27 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12195289/extract-nfsrootfs-4xxupjky,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936488K/1048576K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 46552K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022204] Console: colour dummy device 80x30 <6>[ 0.024098] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034505] CPU: Testing write buffer coherency: ok <6>[ 0.039639] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044935] pid_max: default: 32768 minimum: 301 <6>[ 0.049963] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057398] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066273] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072011] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079709] rcu: Hierarchical SRCU implementation. <6>[ 0.086679] EFI services will not be available. <6>[ 0.088915] smp: Bringing up secondary CPUs ... <6>[ 0.094203] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094212] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105557] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105564] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116762] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116771] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127196] smp: Brought up 1 node, 4 CPUs <6>[ 0.131422] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137879] CPU: All CPU(s) started in SVC mode. <6>[ 0.143307] devtmpfs: initialized <6>[ 0.153820] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159167] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169032] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179253] pinctrl core: initialized pinctrl subsystem <6>[ 0.183740] DMI not present or invalid. <6>[ 0.186842] NET: Registered protocol family 16 <6>[ 0.194128] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200774] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200957] cpuidle: using governor menu <6>[ 0.209056] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.387597] vdd1p1: supplied by regulator-dummy <6>[ 0.396713] vdd3p0: supplied by regulator-dummy <6>[ 0.405711] vdd2p5: supplied by regulator-dummy <6>[ 0.414756] vddarm: supplied by regulator-dummy <6>[ 0.423938] vddpu: supplied by regulator-dummy <6>[ 0.432737] vddsoc: supplied by regulator-dummy <6>[ 0.760573] No ATAGs? <6>[ 0.760764] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.768538] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.778733] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.789009] Serial: AMBA PL011 UART driver <6>[ 0.793148] printk: console [ramoops-1] enabled <6>[ 0.795514] pstore: Registered ramoops as persistent store backend <6>[ 0.801771] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.839330] iommu: Default domain type: Translated <6>[ 0.842049] vgaarb: loaded <5>[ 0.845437] SCSI subsystem initialized <6>[ 0.849204] usbcore: registered new interface driver usbfs <6>[ 0.854366] usbcore: registered new interface driver hub <6>[ 0.859963] usbcore: registered new device driver usb <6>[ 0.866788] i2c i2c-0: IMX I2C adapter registered <6>[ 0.871473] i2c i2c-1: IMX I2C adapter registered <6>[ 0.875958] i2c i2c-2: IMX I2C adapter registered <6>[ 0.881414] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.885294] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.894727] PTP clock support registered <6>[ 0.902581] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.053347] NET: Registered protocol family 2 <6>[ 2.055560] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.064163] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.071422] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.079501] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.086956] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.093638] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.100307] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.107780] NET: Registered protocol family 1 <6>[ 2.112826] RPC: Registered named UNIX socket transport module. <6>[ 2.118367] RPC: Registered udp transport module. <6>[ 2.123351] RPC: Registered tcp transport module. <6>[ 2.128288] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.135006] PCI: CLS 0 bytes, default 64 <6>[ 2.139641] Trying to unpack rootfs image as initramfs... <6>[ 3.095668] Freeing initrd memory: 11868K <4>[ 3.097563] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.104965] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.114714] Initialise system trusted keyrings <6>[ 3.117828] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.130040] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.134069] NFS: Registering the id_resolver key type <5>[ 3.138627] Key type id_resolver registered <5>[ 3.143058] Key type id_legacy registered <6>[ 3.147416] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.154285] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.161939] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.167013] Key type asymmetric registered <5>[ 3.170874] Asymmetric key parser 'x509' registered <6>[ 3.176078] bounce: pool size: 64 pages <6>[ 3.180124] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.187773] io scheduler mq-deadline registered <6>[ 3.192551] io scheduler kyber registered <6>[ 3.236470] mxs-dma 110000.dma-controller: initialized <4>[ 3.243805] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.251585] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.306620] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.314907] SuperH (H)SCI(F) driver initialized <6>[ 3.317854] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.326763] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.334666] printk: console [ttymxc1] enabled <6>[ 3.334666] printk: console [ttymxc1] enabled <6>[ 3.343827] printk: bootconsole [ec_imx21] disabled <6>[ 3.343827] printk: bootconsole [ec_imx21] disabled <6>[ 3.355514] msm_serial: driver initialized <6>[ 3.361534] STMicroelectronics ASC driver initialized <6>[ 3.368862] STM32 USART driver initialized <4>[ 3.383774] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.391676] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.398504] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.415190] brd: module loaded <6>[ 3.426004] loop: module loaded <6>[ 3.433445] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.441640] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.449947] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.458408] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.466426] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.474175] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.481732] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.492334] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.499626] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.508711] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.519503] scsi host0: ahci-imx <6>[ 3.523380] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.544112] CAN device driver interface <6>[ 3.549569] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.559112] pps pps0: new PPS source ptp0 <6>[ 3.581812] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.589464] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.594722] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.600971] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.606655] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.618730] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.626464] usbcore: registered new interface driver pegasus <6>[ 3.632431] usbcore: registered new interface driver asix <6>[ 3.638151] usbcore: registered new interface driver ax88179_178a <6>[ 3.644573] usbcore: registered new interface driver cdc_ether <6>[ 3.650715] usbcore: registered new interface driver smsc75xx <6>[ 3.656790] usbcore: registered new interface driver smsc95xx <6>[ 3.662852] usbcore: registered new interface driver net1080 <6>[ 3.668818] usbcore: registered new interface driver cdc_subset <6>[ 3.675051] usbcore: registered new interface driver zaurus <6>[ 3.680970] usbcore: registered new interface driver cdc_ncm <6>[ 3.690555] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.697376] ehci-pci: EHCI PCI platform driver <6>[ 3.702125] ehci-platform: EHCI generic platform driver <6>[ 3.707950] ehci-orion: EHCI orion driver <6>[ 3.712479] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.716961] ehci-st: EHCI STMicroelectronics driver <6>[ 3.722307] ehci-exynos: EHCI Exynos driver <6>[ 3.726968] ehci-atmel: EHCI Atmel driver <6>[ 3.731425] tegra-ehci: Tegra EHCI driver <6>[ 3.735941] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.742404] ohci-pci: OHCI PCI platform driver <6>[ 3.747176] ohci-platform: OHCI generic platform driver <6>[ 3.752958] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.757430] ohci-st: OHCI STMicroelectronics driver <6>[ 3.762798] ohci-atmel: OHCI Atmel driver <6>[ 3.768366] usbcore: registered new interface driver usb-storage <6>[ 3.783100] i2c /dev entries driver <6>[ 3.806844] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.813328] sdhci: Copyright(c) Pierre Ossman <6>[ 3.820761] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.829082] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.836304] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.841589] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.843213] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.847159] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.859501] usbcore: registered new interface driver usbhid <6>[ 3.865369] usbhid: USB HID core driver <6>[ 3.867207] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.875202] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.876261] NET: Registered protocol family 10 <6>[ 3.878617] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.881762] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.882690] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.887572] Segment Routing with IPv6 <6>[ 3.912207] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.919003] NET: Registered protocol family 17 <6>[ 3.923750] can: controller area network core <6>[ 3.928456] NET: Registered protocol family 29 <6>[ 3.930292] mmc2: new high speed SDHC card at address aaaa <6>[ 3.933189] can: raw protocol <6>[ 3.933200] can: broadcast manager protocol <6>[ 3.939833] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <6>[ 3.942189] can: netlink gateway - max_hops=1 <5>[ 3.956539] Key type dns_resolver registered <4>[ 3.959632] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.968774] GPT:29296874 != 31116287 <6>[ 3.970744] ThumbEE CPU extension supported. <4>[ 3.972645] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.972651] GPT:29296874 != 31116287 <4>[ 3.972659] GPT: Use GNU Parted to correct GPT errors. <5>[ 3.977202] Registering SWP/SWPB emulation handler <6>[ 3.983515] mmcblk2: p1 p2 p3 <5>[ 3.992864] Loading compiled-in X.509 certificates <6>[ 4.011316] pstore: Using crash dump compression: deflate <4>[ 4.038724] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.046646] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.054563] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.070966] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.081024] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.086231] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.122619] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.129773] hub 1-0:1.0: USB hub found <6>[ 4.133926] hub 1-0:1.0: 1 port detected <6>[ 4.142553] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.157763] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.165686] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.173583] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.185696] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.193602] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.201404] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.211392] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.223641] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.231519] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.239452] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.253280] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.462550] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.664248] hub 1-1:1.0: USB hub found <6>[ 4.668462] hub 1-1:1.0: 3 ports detected <4>[ 4.678930] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.686899] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.695187] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.362981] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.382623] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.412637] Sending DHCP requests ., OK <6>[ 7.456713] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 7.465074] IP-Config: Complete: <6>[ 7.468597] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.479349] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 7.487497] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.487508] nameserver0=192.168.201.1 <6>[ 7.506231] Freeing unused kernel memory: 2048K <6>[ 7.553514] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 8.450420] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.470224] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.478334] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.487811] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.505039] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.520289] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.528386] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.543788] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.555603] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.567925] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 8.568049] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.574783] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <4>[ 8.613733] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.621668] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.629203] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.635620] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.641988] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.668440] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.680836] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.683706] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.689516] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.703249] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.705859] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.719644] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.771795] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.832559] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.837986] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.844893] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 8.853407] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.858329] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.861575] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.869300] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.877806] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.892176] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.898534] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.902835] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.909225] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.921742] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.922847] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.939175] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.950365] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.965155] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.973146] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.994982] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.003583] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.012124] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.020706] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.031111] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.056256] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.064287] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.224635] caam algorithms registered in /proc/crypto <6>[ 9.231475] caam 2100000.crypto: registering rng-caam <6>[ 9.240435] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.248972] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.257495] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.266007] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Ru<4>[ 9.284740] panel-simple panel-lvds0: supply power not found, using dummy regulator nning /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 sec<4>[ 9.301567] panel-simple panel-lcd: supply power not found, using dummy regulator s for any ethernet to become avai<4>[ 9.311080] panel-simple panel-lcd: Specify missing connector_type lable Device /sys/class/net/eth0 found done. <5>[ 9.419389] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:1c mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.36 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-6 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.161790] systemd[1]: System time before build time, advancing clock. <30>[ 10.224425] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.248605] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.294552] systemd[1]: Set hostname to . <30>[ 11.010745] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.020161] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.032901] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.042382] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.083962] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.124108] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.163569] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.203429] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.242893] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.283135] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.295912] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.333523] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.362997] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.402834] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.433115] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.463921] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.537888] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.547723] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.584116] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.625132] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.665508] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 11.704008] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 11.743729] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.753274] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.765837] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 11.807343] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 11.846387] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 11.885675] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 11.926219] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 11.966186] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.007342] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.023465] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.059668] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.106294] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.146080] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.188180] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.223285] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.263721] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.319605] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 12.611850] systemd-journald[269]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Started Network Service. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Network Name Resolution... [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.201-cip41 #1 SMP Wed Dec 6 06:16:27 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12195289/extract-nfsrootfs-4xxupjky' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12195289/extract-nfsrootfs-4xxupjky' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12195289/environment . /lava-12195289/environment / # /lava-12195289/bin/lava-test-runner /lava-12195289/0 /lava-12195289/bin/lava-test-runner /lava-12195289/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12195289/0/tests/0_timesync-off ++ cat uuid + UUID=12195289_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-12195289/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=12195289_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.201-cip41-16-g3c85fba3b6e5d/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-12-06 06:36:17-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.201-cip41-16-g3c85fba3b6e5d/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1410512 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 2%[ ] 30.84K 117KB/s kselftest.tar.xz 5%[> ] 78.43K 148KB/s kselftest.tar.xz 8%[> ] 115.68K 145KB/s kselftest.tar.xz 11%[=> ] 158.10K 149KB/s kselftest.tar.xz 12%[=> ] 177.42K 134KB/s kselftest.tar.xz 15%[==> ] 212.77K 134KB/s kselftest.tar.xz 16%[==> ] 233.05K 125KB/s kselftest.tar.xz 17%[==> ] 234.46K 110KB/s kselftest.tar.xz 18%[==> ] 259.92K 109KB/s kselftest.tar.xz 20%[===> ] 286.78K 108KB/s kselftest.tar.xz 21%[===> ] 301.85K 103KB/s kselftest.tar.xz 23%[===> ] 327.31K 103KB/s eta 10s kselftest.tar.xz 25%[====> ] 345.69K 98.8KB/s eta 10s kselftest.tar.xz 26%[====> ] 360.32K 97.0KB/s eta 10s kselftest.tar.xz 27%[====> ] 380.11K 95.5KB/s eta 10s kselftest.tar.xz 28%[====> ] 397.08K 93.5KB/s eta 10s kselftest.tar.xz 30%[=====> ] 416.88K 92.4KB/s eta 10s kselftest.tar.xz 32%[=====> ] 440.92K 92.3KB/s eta 10s kselftest.tar.xz 33%[=====> ] 467.78K 92.8KB/s eta 10s kselftest.tar.xz 36%[======> ] 497.48K 87.7KB/s eta 9s kselftest.tar.xz 38%[======> ] 530.00K 86.7KB/s eta 9s kselftest.tar.xz 40%[=======> ] 561.11K 84.4KB/s eta 9s kselftest.tar.xz 42%[=======> ] 585.15K 86.0KB/s eta 9s kselftest.tar.xz 44%[=======> ] 612.02K 85.1KB/s eta 9s kselftest.tar.xz 46%[========> ] 645.96K 92.9KB/s eta 7s kselftest.tar.xz 49%[========> ] 685.07K 96.0KB/s eta 7s kselftest.tar.xz 51%[=========> ] 710.52K 97.1KB/s eta 7s kselftest.tar.xz 54%[=========> ] 744.94K 100KB/s eta 7s kselftest.tar.xz 55%[==========> ] 767.08K 101KB/s eta 6s kselftest.tar.xz 56%[==========> ] 783.12K 103KB/s eta 6s kselftest.tar.xz 57%[==========> ] 798.19K 103KB/s eta 6s kselftest.tar.xz 59%[==========> ] 821.30K 102KB/s eta 6s kselftest.tar.xz 61%[===========> ] 845.34K 102KB/s eta 5s kselftest.tar.xz 63%[===========> ] 870.79K 101KB/s eta 5s kselftest.tar.xz 65%[============> ] 901.90K 103KB/s eta 5s kselftest.tar.xz 67%[============> ] 931.60K 103KB/s eta 5s kselftest.tar.xz 68%[============> ] 947.15K 100KB/s eta 4s kselftest.tar.xz 70%[=============> ] 966.95K 98.3KB/s eta 4s kselftest.tar.xz 72%[=============> ] 996.64K 99.0KB/s eta 4s kselftest.tar.xz 74%[=============> ] 1024K 97.4KB/s eta 4s kselftest.tar.xz 76%[==============> ] 1.03M 96.5KB/s eta 3s kselftest.tar.xz 78%[==============> ] 1.06M 96.1KB/s eta 3s kselftest.tar.xz 80%[===============> ] 1.08M 93.2KB/s eta 3s kselftest.tar.xz 82%[===============> ] 1.11M 97.2KB/s eta 3s kselftest.tar.xz 84%[===============> ] 1.14M 96.5KB/s eta 3s kselftest.tar.xz 86%[================> ] 1.17M 96.1KB/s eta 2s kselftest.tar.xz 89%[================> ] 1.21M 100KB/s eta 2s kselftest.tar.xz 91%[=================> ] 1.23M 104KB/s eta 2s kselftest.tar.xz 92%[=================> ] 1.25M 102KB/s eta 2s kselftest.tar.xz 94%[=================> ] 1.27M 103KB/s eta 2s kselftest.tar.xz 96%[==================> ] 1.30M 102KB/s eta 0s kselftest.tar.xz 98%[==================> ] 1.33M 100KB/s eta 0s kselftest.tar.xz 100%[===================>] 1.34M 101KB/s eta 0s kselftest.tar.xz 100%[===================>] 1.34M 101KB/s in 14s 2023-12-06 06:36:32 (98.5 KB/s) - 'kselftest.tar.xz' saved [1410512/1410512] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== shardfile-filesystems pass <12>[ 45.752772] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #