Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1052588/tftp-deploy-f17b4muz/kernel/zImage tftp 0x82000000 1052588/tftp-deploy-f17b4muz/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1052588/tftp-deploy-f17b4muz/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.3 MiB/s done Bytes transferred = 4609664 (465680 hex) => tftp 0x83000000 1052588/tftp-deploy-f17b4muz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1052588/tftp-deploy-f17b4muz/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1052588/tftp-deploy-f17b4muz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.1 MiB/s done Bytes transferred = 14176301 (d8502d hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1052588/tftp-deploy-f17b4muz/dtb/am335x-boneblack.dtb tftp 0x88000000 1052588/tftp-deploy-f17b4muz/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1052588/tftp-deploy-f17b4muz/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.3 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-12-06 6:08:21 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14176237 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip41 (KernelCI@build-j36120-arm-gcc-10-omap2plus-defconfig-kh84q) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Dec 6 05:38:54 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472020K/522240K available (9216K kernel code, 1027K rwdata, 2180K rodata, 1024K init, 278K bss, 33836K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008343] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018562] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030213] Console: colour dummy device 80x30 <3>[ 0.035083] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042143] This ensures that you still see kernel messages. Please <3>[ 0.048869] update your kernel commandline. <6>[ 0.053472] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095543] CPU: Testing write buffer coherency: ok <6>[ 0.100925] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106390] pid_max: default: 32768 minimum: 301 <6>[ 0.111551] LSM: Security Framework initializing <6>[ 0.116651] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124466] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134141] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140657] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147857] rcu: Hierarchical SRCU implementation. <6>[ 0.153655] smp: Bringing up secondary CPUs ... <6>[ 0.158593] smp: Brought up 1 node, 1 CPU <6>[ 0.163024] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169754] CPU: All CPU(s) started in SVC mode. <6>[ 0.175495] devtmpfs: initialized <6>[ 0.191324] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199861] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210297] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218945] pinctrl core: initialized pinctrl subsystem <6>[ 0.226522] NET: Registered protocol family 16 <6>[ 0.234204] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260675] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266769] audit: initializing netlink subsys (disabled) <6>[ 0.273847] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273861] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280469] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.287189] cpuidle: using governor menu <5>[ 1.167345] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.292717] No ATAGs? <6>[ 1.295343] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.319900] Kprobes globally optimized <6>[ 1.333097] iommu: Default domain type: Translated <6>[ 1.340257] vgaarb: loaded <5>[ 1.343845] SCSI subsystem initialized <6>[ 1.349053] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.354438] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.364165] PTP clock support registered <6>[ 1.369751] clocksource: Switched to clocksource dmtimer <5>[ 2.007886] VFS: Disk quotas dquot_6.6.0 <6>[ 2.012394] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.029231] NET: Registered protocol family 2 <6>[ 2.034415] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.043089] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.052053] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.060348] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.068008] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.074945] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.081980] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.089589] NET: Registered protocol family 1 <6>[ 2.095389] RPC: Registered named UNIX socket transport module. <6>[ 2.101850] RPC: Registered udp transport module. <6>[ 2.106957] RPC: Registered tcp transport module. <6>[ 2.112085] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.118993] PCI: CLS 0 bytes, default 64 <6>[ 2.124074] Trying to unpack rootfs image as initramfs... <6>[ 3.113233] Freeing initrd memory: 13848K <6>[ 3.118918] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.129328] Initialise system trusted keyrings <6>[ 3.134705] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.142926] NFS: Registering the id_resolver key type <5>[ 3.148461] Key type id_resolver registered <5>[ 3.153111] Key type id_legacy registered <6>[ 3.157562] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.165618] Key type asymmetric registered <5>[ 3.170158] Asymmetric key parser 'x509' registered <6>[ 3.175459] io scheduler mq-deadline registered <6>[ 3.180406] io scheduler kyber registered <3>[ 3.318705] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.327417] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.436452] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.478620] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.550595] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.559223] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.619216] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.627936] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.645450] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.654139] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.717821] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.726393] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.753413] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.767906] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.778864] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.788297] printk: console [ttyS0] enabled <6>[ 3.788297] printk: console [ttyS0] enabled <6>[ 3.797367] printk: bootconsole [omap8250] disabled <6>[ 3.797367] printk: bootconsole [omap8250] disabled <6>[ 3.821306] brd: module loaded <6>[ 3.832064] loop: module loaded <3>[ 3.837521] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.909789] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.952418] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.962311] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.968965] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.974804] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.982362] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 3.991421] i2c /dev entries driver <5>[ 3.996920] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.004848] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.011396] sdhci: Copyright(c) Pierre Ossman <6>[ 4.016744] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.025057] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.034844] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.043317] Initializing XFRM netlink socket <6>[ 4.048119] NET: Registered protocol family 10 <6>[ 4.054570] Segment Routing with IPv6 <6>[ 4.058616] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.065693] NET: Registered protocol family 17 <6>[ 4.070546] NET: Registered protocol family 15 <5>[ 4.075415] Key type dns_resolver registered <6>[ 4.080616] oprofile: using arm/armv7 <6>[ 4.084659] ThumbEE CPU extension supported. <5>[ 4.089234] Registering SWP/SWPB emulation handler <3>[ 4.094787] omap_voltage_late_init: Voltage driver support not added <3>[ 4.101503] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.109913] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.118580] SmartReflex Class3 initialized <6>[ 4.123719] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.132689] Loading compiled-in X.509 certificates <6>[ 4.157799] OMAP GPIO hardware version 0.1 <4>[ 4.190443] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.204086] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.212764] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.219102] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.229138] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.240691] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.249784] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.254949] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.268155] mmc1: new high speed MMC card at address 0001 <6>[ 4.275015] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.280613] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.287285] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.293902] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.303443] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.312435] mmcblk1: p1 <6>[ 4.320681] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.411280] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.560416] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.579762] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.609855] Sending DHCP requests ., OK <6>[ 7.653841] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 7.661919] IP-Config: Complete: <6>[ 7.665429] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.675930] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.682961] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.682968] nameserver0=192.168.11.1 <6>[ 7.696376] Freeing unused kernel memory: 1024K <6>[ 7.720207] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.956245] udevd[100]: starting version 3.2.9 <5>[ 7.962997] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.970928] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.977817] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.995178] udevd[100]: specified user 'tss' unknown <27>[ 8.001068] udevd[100]: specified group 'tss' unknown <30>[ 8.012516] udevd[101]: starting eudev-3.2.9 <6>[ 8.668416] remoteproc remoteproc0: wkup_m3 is available <4>[ 9.148503] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.157700] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.210062] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 9.260127] usbcore: registered new interface driver usbfs <6>[ 9.265985] usbcore: registered new interface driver hub <6>[ 9.271791] usbcore: registered new device driver usb <4>[ 9.469543] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.478720] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 9.527610] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 9.662946] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 9.670693] at24 2-0054: supply vcc not found, using dummy regulator <3>[ 9.755170] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.770706] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.776362] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 9.792340] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 9.860643] at24 2-0056: supply vcc not found, using dummy regulator <3>[ 9.918204] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 9.929285] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <4>[ 9.941177] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 9.959181] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.967898] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.975471] usb usb1: Product: MUSB HDRC host driver <6>[ 9.980743] usb usb1: Manufacturer: Linux 5.10.201-cip41 musb-hcd <6>[ 9.987126] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 10.040869] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <3>[ 10.060484] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.110566] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 10.115989] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <3>[ 10.139661] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.271998] tda998x 0-0070: found TDA19988 <6>[ 10.300459] hub 1-0:1.0: USB hub found <3>[ 10.313920] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.339891] hub 1-0:1.0: 1 port detected <3>[ 10.381932] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 10.502944] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.905746] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <3>[ 11.016002] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 11.091357] remoteproc remoteproc0: powering up wkup_m3 <4>[ 11.097023] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 11.106957] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 11.113201] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 11.580585] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 11.680260] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 11.695529] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 11.702709] random: crng init done <6>[ 11.768313] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 11.777745] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 12.014244] PM: Cannot get wkup_m3_ipc handle <6>[ 12.313660] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.360466] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.387808] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 12.401067] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 12.457927] PM: Cannot get wkup_m3_ipc handle <3>[ 12.510238] PM: Cannot get wkup_m3_ipc handle <3>[ 12.884830] PM: Cannot get wkup_m3_ipc handle <3>[ 12.921702] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1052588/environment . /lava-1052588/environment / # /lava-1052588/bin/lava-test-runner /lava-1052588/0 /lava-1052588/bin/lava-test-runner /lava-1052588/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1052588/0/tests/0_dmesg + cat uuid + UUID=1052588_1.5.2.4.1 + <8>[ 13.828798] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 13.895362] <8>[ 13.955970] <8>[ 14.016765] + set +x <8>[ 14.027946] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1052588/environment / # . /lava-1052588/environment/lava-1052588/bin/lava-test-runner /lava-1052588/1 / # /lava-1052588/bin/lava-test-runner /lava-1052588/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1052588/1/tests/1_bootrr + cat uuid + UUID=1052588_1.5.2.4.5 + <8>[ 14.560118] set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1052588/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto pm33xx /lava-1052588/1/../bin/lava-test-case <8>[ 15.667884] /lava-1052588/1/../bin/lava-test-case <8>[ 15.723530] /lava-1052588/1/../bin/lava-test-case <8>[ 15.756625] /lava-1052588/1/../bin/lava-test-case <8>[ 15.818866] /lava-1052588/1/../bin/lava-test-case <8>[ 15.870609] /lava-1052588/1/../bin/lava-test-case <8>[ 15.911923] /lava-1052588/1/../bin/lava-test-case <8>[ 15.963071] /lava-1052588/1/../bin/lava-test-case <8>[ 16.013119] /lava-1052588/1/../bin/lava-test-case <8>[ 16.070681] /lava-1052588/1/../bin/lava-test-case <8>[ 16.121009] /lava-1052588/1/../bin/lava-test-case <8>[ 16.162231] /lava-1052588/1/../bin/lava-test-case <8>[ 16.212969] /lava-1052588/1/../bin/lava-test-case <8>[ 16.253225] /lava-1052588/1/../bin/lava-test-case <8>[ 16.293829] /lava-1052588/1/../bin/lava-test-case <8>[ 16.334960] /lava-1052588/1/../bin/lava-test-case <8>[ 16.385246] /lava-1052588/1/../bin/lava-test-case <8>[ 16.426965] /lava-1052588/1/../bin/lava-test-case <8>[ 16.478503] /lava-1052588/1/../bin/lava-test-case <8>[ 16.528637] /lava-1052588/1/../bin/lava-test-case <8>[ 16.570078] /lava-1052588/1/../bin/lava-test-case <8>[ 16.621019] /lava-1052588/1/../bin/lava-test-case <8>[ 16.672213] /lava-1052588/1/../bin/lava-test-case <8>[ 16.713902] /lava-1052588/1/../bin/lava-test-case <8>[ 16.765008] /lava-1052588/1/../bin/lava-test-case <8>[ 16.806286] /lava-1052588/1/../bin/lava-test-case <8>[ 16.857505] /lava-1052588/1/../bin/lava-test-case <8>[ 16.898351] /lava-1052588/1/../bin/lava-test-case <8>[ 17.978384] /lava-1052588/1/../bin/lava-test-case <8>[ 18.020516] /lava-1052588/1/../bin/lava-test-case <8>[ 18.072118] /lava-1052588/1/../bin/lava-test-case <8>[ 18.113549] /lava-1052588/1/../bin/lava-test-case <8>[ 18.164773] /lava-1052588/1/../bin/lava-test-case <8>[ 18.205512] /lava-1052588/1/../bin/lava-test-case <8>[ 18.256696] /lava-1052588/1/../bin/lava-test-case <8>[ 18.297554] /lava-1052588/1/../bin/lava-test-case <8>[ 18.348771] /lava-1052588/1/../bin/lava-test-case <8>[ 18.389651] /lava-1052588/1/../bin/lava-test-case <8>[ 18.441130] /lava-1052588/1/../bin/lava-test-case <8>[ 18.481993] /lava-1052588/1/../bin/lava-test-case <8>[ 18.532859] /lava-1052588/1/../bin/lava-test-case <8>[ 18.573249] /lava-1052588/1/../bin/lava-test-case <8>[ 18.624628] /lava-1052588/1/../bin/lava-test-case <8>[ 18.665814] /lava-1052588/1/../bin/lava-test-case <8>[ 18.716936] /lava-1052588/1/../bin/lava-test-case <8>[ 18.757537] /lava-1052588/1/../bin/lava-test-case <8>[ 18.808183] /lava-1052588/1/../bin/lava-test-case <8>[ 18.849416] /lava-1052588/1/../bin/lava-test-case <8>[ 18.900459] /lava-1052588/1/../bin/lava-test-case <8>[ 18.941671] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-1052588/1/../bin/lava-test-case <8>[ 18.984377] /lava-1052588/1/../bin/lava-test-case <8>[ 19.035403] /lava-1052588/1/../bin/lava-test-case <8>[ 19.083987] + set +x <8>[ 19.100347] / #