Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1053275/tftp-deploy-_3_hc472/kernel/zImage tftp 0x82000000 1053275/tftp-deploy-_3_hc472/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1053275/tftp-deploy-_3_hc472/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 5.2 MiB/s done Bytes transferred = 9708032 (942200 hex) => tftp 0x83000000 1053275/tftp-deploy-_3_hc472/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1053275/tftp-deploy-_3_hc472/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1053275/tftp-deploy-_3_hc472/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################# 5.2 MiB/s done Bytes transferred = 12159790 (b98b2e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1053275/tftp-deploy-_3_hc472/dtb/am335x-boneblack.dtb tftp 0x88000000 1053275/tftp-deploy-_3_hc472/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1053275/tftp-deploy-_3_hc472/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1053275/extract-nfsrootfs-phbpbegk,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1053275/extract-nfsrootfs-phbpbegk,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-12-07 12:25:00 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12159726 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip41 (KernelCI@build-j37450-arm-gcc-10-multi-v7-defconfig-w24sx) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Dec 7 11:37:36 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1053275/extract-nfsrootfs-phbpbegk,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 414668K/522240K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 42036K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008338] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019072] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033176] Console: colour dummy device 80x30 <3>[ 0.038044] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045092] This ensures that you still see kernel messages. Please <3>[ 0.051806] update your kernel commandline. <6>[ 0.056414] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096035] CPU: Testing write buffer coherency: ok <6>[ 0.101400] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106860] pid_max: default: 32768 minimum: 301 <6>[ 0.112042] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.119848] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.129154] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135491] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.144686] rcu: Hierarchical SRCU implementation. <6>[ 0.154594] EFI services will not be available. <6>[ 0.159772] smp: Bringing up secondary CPUs ... <6>[ 0.164705] smp: Brought up 1 node, 1 CPU <6>[ 0.169092] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.175826] CPU: All CPU(s) started in SVC mode. <6>[ 0.181442] devtmpfs: initialized <6>[ 0.195685] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.204219] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.214649] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.225833] pinctrl core: initialized pinctrl subsystem <6>[ 0.234205] DMI not present or invalid. <6>[ 0.239182] NET: Registered protocol family 16 <6>[ 0.246675] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.273532] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.281738] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.281943] cpuidle: using governor menu <6>[ 1.327258] No ATAGs? <6>[ 1.329935] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.344520] Serial: AMBA PL011 UART driver <6>[ 1.382772] iommu: Default domain type: Translated <6>[ 1.388509] vgaarb: loaded <5>[ 1.392658] SCSI subsystem initialized <6>[ 1.397679] usbcore: registered new interface driver usbfs <6>[ 1.403739] usbcore: registered new interface driver hub <6>[ 1.409546] usbcore: registered new device driver usb <6>[ 1.416819] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.422244] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.431938] PTP clock support registered <6>[ 1.440185] clocksource: Switched to clocksource dmtimer <6>[ 2.448768] NET: Registered protocol family 2 <6>[ 2.453924] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.462406] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.471330] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.479595] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.487272] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.494193] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.501214] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.508788] NET: Registered protocol family 1 <6>[ 2.514418] RPC: Registered named UNIX socket transport module. <6>[ 2.520861] RPC: Registered udp transport module. <6>[ 2.525963] RPC: Registered tcp transport module. <6>[ 2.531084] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.537981] PCI: CLS 0 bytes, default 64 <6>[ 2.543009] Trying to unpack rootfs image as initramfs... <6>[ 3.324890] Freeing initrd memory: 11876K <6>[ 3.330378] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.340808] Initialise system trusted keyrings <6>[ 3.346095] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.359308] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.366675] NFS: Registering the id_resolver key type <5>[ 3.372291] Key type id_resolver registered <5>[ 3.376860] Key type id_legacy registered <6>[ 3.381388] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.388550] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.396484] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.401834] Key type asymmetric registered <5>[ 3.406324] Asymmetric key parser 'x509' registered <6>[ 3.411722] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.419596] io scheduler mq-deadline registered <6>[ 3.424548] io scheduler kyber registered <3>[ 3.576558] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.585263] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.703564] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.748567] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.825958] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.834666] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.899349] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.908049] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.926537] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.935261] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.003700] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.012232] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.054630] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.158368] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 4.170928] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.180317] printk: console [ttyS0] enabled <6>[ 4.180317] printk: console [ttyS0] enabled <6>[ 4.189342] printk: bootconsole [omap8250] disabled <6>[ 4.189342] printk: bootconsole [omap8250] disabled <6>[ 4.203204] SuperH (H)SCI(F) driver initialized <6>[ 4.210069] msm_serial: driver initialized <6>[ 4.215049] STMicroelectronics ASC driver initialized <6>[ 4.223285] STM32 USART driver initialized <6>[ 4.230658] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 4.250132] random: crng init done <6>[ 4.263597] brd: module loaded <6>[ 4.273322] loop: module loaded <6>[ 4.298629] CAN device driver interface <6>[ 4.304863] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 4.313192] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.318450] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.324835] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.330571] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.400213] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.424172] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.434098] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.440823] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.446594] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.455742] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.463648] usbcore: registered new interface driver pegasus <6>[ 4.469650] usbcore: registered new interface driver asix <6>[ 4.475409] usbcore: registered new interface driver ax88179_178a <6>[ 4.481851] usbcore: registered new interface driver cdc_ether <6>[ 4.488023] usbcore: registered new interface driver smsc75xx <6>[ 4.494128] usbcore: registered new interface driver smsc95xx <6>[ 4.500212] usbcore: registered new interface driver net1080 <6>[ 4.506187] usbcore: registered new interface driver cdc_subset <6>[ 4.512440] usbcore: registered new interface driver zaurus <6>[ 4.518350] usbcore: registered new interface driver cdc_ncm <6>[ 4.529703] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.536642] ehci-pci: EHCI PCI platform driver <6>[ 4.541452] ehci-platform: EHCI generic platform driver <6>[ 4.547454] ehci-orion: EHCI orion driver <6>[ 4.552202] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.556815] ehci-st: EHCI STMicroelectronics driver <6>[ 4.562352] ehci-exynos: EHCI Exynos driver <6>[ 4.567111] ehci-atmel: EHCI Atmel driver <6>[ 4.571772] tegra-ehci: Tegra EHCI driver <6>[ 4.576400] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.582970] ohci-pci: OHCI PCI platform driver <6>[ 4.587773] ohci-platform: OHCI generic platform driver <6>[ 4.593781] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.598387] ohci-st: OHCI STMicroelectronics driver <6>[ 4.603940] ohci-atmel: OHCI Atmel driver <6>[ 4.610207] usbcore: registered new interface driver usb-storage <6>[ 4.627550] i2c /dev entries driver <5>[ 4.660279] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.668562] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.675121] sdhci: Copyright(c) Pierre Ossman <6>[ 4.684232] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.693701] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.708510] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.768434] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.778033] usbcore: registered new interface driver usbhid <6>[ 4.784018] usbhid: USB HID core driver <6>[ 4.797636] NET: Registered protocol family 10 <6>[ 4.803952] Segment Routing with IPv6 <6>[ 4.807989] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.815030] NET: Registered protocol family 17 <6>[ 4.819779] can: controller area network core <6>[ 4.824566] NET: Registered protocol family 29 <6>[ 4.829296] can: raw protocol <6>[ 4.832586] can: broadcast manager protocol <6>[ 4.837061] can: netlink gateway - max_hops=1 <5>[ 4.842519] Key type dns_resolver registered <6>[ 4.847238] ThumbEE CPU extension supported. <5>[ 4.851881] Registering SWP/SWPB emulation handler <3>[ 4.857390] omap_voltage_late_init: Voltage driver support not added <6>[ 4.865640] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.874546] Loading compiled-in X.509 certificates <6>[ 4.896055] OMAP GPIO hardware version 0.1 <4>[ 4.930778] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.944076] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.959363] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <4>[ 4.965760] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 4.973148] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 4.981138] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <4>[ 4.991140] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 5.000700] mmc1: new high speed MMC card at address 0001 <6>[ 5.007308] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 5.012565] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.019087] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.025726] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 5.035245] mmcblk1: p1 <4>[ 5.039388] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 5.074433] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 5.114021] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 5.153068] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 5.176944] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 5.186130] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 5.191260] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.254333] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.296363] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.382057] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 8.511088] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 8.520341] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.550337] Sending DHCP requests ., OK <6>[ 8.594464] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 8.602611] IP-Config: Complete: <6>[ 8.606155] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 8.616719] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 8.623804] bootserver=0.0.0.0, rootserver=192.168.11.5, rootpath= <6>[ 8.623823] nameserver0=192.168.11.1 <6>[ 8.648539] Freeing unused kernel memory: 2048K <6>[ 8.671153] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <4>[ 11.583261] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.592449] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 11.821545] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.830684] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 11.995146] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 12.000939] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 12.200740] hub 1-0:1.0: USB hub found <6>[ 12.226819] hub 1-0:1.0: 1 port detected Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 64:cf:d9:3f:a0:d5 mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 192.168.11.255 IP-Config: eth0 complete (dhcp from 192.168.11.1): address: 192.168.11.4 broadcast: 192.168.11.255 netmask: 255.255.255.0 gateway: 192.168.11.1 dns0 : 192.168.11.1 dns1 : 0.0.0.0 domain : usen.ad.jp rootserver: 192.168.11.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 15.351602] systemd[1]: System time before build time, advancing clock. <30>[ 15.452727] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 15.477260] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 15.523213] systemd[1]: Set hostname to . <30>[ 17.209940] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 17.220770] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 17.233728] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 17.244050] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. <30>[ 17.285749] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[0m. <30>[ 17.321732] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. <30>[ 17.362648] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. <30>[ 17.402079] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. <30>[ 17.441246] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. <30>[ 17.481791] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 17.497197] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. <30>[ 17.531039] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. <30>[ 17.571305] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. <30>[ 17.610978] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. <30>[ 17.650878] systemd[1]: Reached target Swap. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. <30>[ 17.692881] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. <30>[ 17.782542] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 17.793856] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/log)[0m. <30>[ 17.831936] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. <30>[ 17.875455] systemd[1]: Listening on Network Service Netlink Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlink Socket[0m. <30>[ 17.924776] systemd[1]: Listening on udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0m. <30>[ 17.963358] systemd[1]: Listening on udev Kernel Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. <30>[ 18.002941] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 18.013653] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 18.030767] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Debug File System[0m... <30>[ 18.065587] systemd[1]: Mounting Kernel Trace File System... Mounting [0;1;39mKernel Trace File System[0m... <30>[ 18.144150] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting [0;1;39mCreate list of st…odes for the current kernel[0m... <30>[ 18.215586] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module configfs[0m... <30>[ 18.265025] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module drm[0m... <30>[ 18.314946] systemd[1]: Starting Load Kernel Module fuse... Starting [0;1;39mLoad Kernel Module fuse[0m... <30>[ 18.365379] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 18.379705] systemd[1]: Starting Journal Service... Starting [0;1;39mJournal Service[0m... <30>[ 18.451663] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mLoad Kernel Modules[0m... <30>[ 18.485058] systemd[1]: Starting Remount Root and Kernel File Systems... Starting [0;1;39mRemount Root and Kernel File Systems[0m... <30>[ 18.536719] systemd[1]: Starting Coldplug All udev Devices... Starting [0;1;39mColdplug All udev Devices[0m... <30>[ 18.616997] systemd[1]: Mounted Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m. <30>[ 18.701854] systemd[1]: Mounted Kernel Trace File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Trace File System[0m. <30>[ 18.762911] systemd[1]: Finished Create list of static device nodes for the current kernel. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. <30>[ 18.934256] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 18.962247] systemd[1]: Finished Load Kernel Module configfs. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. <30>[ 18.992967] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 19.020787] systemd[1]: Finished Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. <30>[ 19.062761] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 19.080652] systemd[1]: Finished Load Kernel Module fuse. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. <30>[ 19.113221] systemd[1]: Finished Load Kernel Modules. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. <30>[ 19.133079] systemd[1]: Finished Remount Root and Kernel File Systems. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. <30>[ 19.192646] systemd[1]: Condition check resulted in FUSE Control File System being skipped. <30>[ 19.245152] systemd[1]: Mounting Kernel Configuration File System... Mounting [0;1;39mKernel Configuration File System[0m... <30>[ 19.290833] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 19.323940] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <30>[ 19.364217] systemd[1]: Starting Load/Save Random Seed... Starting [0;1;39mLoad/Save Random Seed[0m... <30>[ 19.415503] systemd[1]: Starting Apply Kernel Variables... Starting [0;1;39mApply Kernel Variables[0m... <30>[ 19.462278] systemd[1]: Starting Create System Users... Starting [0;1;39mCreate System Users[0m... <30>[ 19.532881] systemd[1]: Started Journal Service. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. Starting [0;1;39mFlush Journal to Persistent Storage[0m... [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. <46>[ 19.930472] systemd-journald[148]: Received client request to flush runtime journal. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mNetwork Time Synchronization[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Time Synchronization[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Set[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Synchronized[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0m[0;31m* [0m] (1 of 4) A start job is running for…k Name Resolution (12s / 1min 37s) M[K[[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [K[[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Found device [0;1;39m/dev/ttyS0[0m. [[0;1;31m*[0m[0;31m* [0m] (1 of 2) A start job is running for…a Check Snapshots (17s / no limit) M[K[[0;31m*[0;1;31m*[0m[0;31m* [0m] (1 of 2) A start job is running for…a Check Snapshots (17s / no limit) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] (2 of 2) A start job is running for… Login Management (18s / 1min 40s) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] (2 of 2) A start job is running for… Login Management (18s / 1min 40s) M[K[ [0;31m*[0;1;31m*[0m[0;31m*[0m] (2 of 2) A start job is running for… Login Management (18s / 1min 40s) M[K[ [0;31m*[0;1;31m*[0m] (1 of 2) A start job is running for…a Check Snapshots (18s / no limit) M[K[ [0;31m*[0m] (1 of 2) A start job is running for…a Check Snapshots (19s / no limit) M[K[ [0;31m*[0;1;31m*[0m] (1 of 2) A start job is running for…a Check Snapshots (19s / no limit) M[K[[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [K[[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Reached target [0;1;39mHardware activated USB gadget[0m. [[0;32m OK [0m] Listening on [0;1;39mLoad/Save RF …itch Status /dev/rfkill Watch[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyS0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... Debian GNU/Linux 11 dseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.201-cip41 #1 SMP Thu Dec 7 11:37:36 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/1053275/extract-nfsrootfs-phbpbegk' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/1053275/extract-nfsrootfs-phbpbegk' / # export NFS_SERVER_IP='192.168.11.5' export NFS_SERVER_IP='192.168.11.5' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-1053275/environment . /lava-1053275/environment / # /lava-1053275/bin/lava-test-runner /lava-1053275/0 /lava-1053275/bin/lava-test-runner /lava-1053275/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-1053275/0/tests/0_timesync-off ++ cat uuid + UUID=1053275_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-openat2 + TESTRUN_ID=1_kselftest-openat2 + cd /lava-1053275/0/tests/1_kselftest-openat2 ++ cat uuid + UUID=1053275_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c openat2 -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.201-cip41-28-g38e219eb6aa85/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b beaglebone-black -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-12-07 12:26:39-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.201-cip41-28-g38e219eb6aa85/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1410472 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 49.92K 232KB/s kselftest.tar.xz 15%[==> ] 218.67K 504KB/s kselftest.tar.xz 31%[=====> ] 428.20K 654KB/s kselftest.tar.xz 95%[==================> ] 1.29M 1.48MB/s kselftest.tar.xz 100%[===================>] 1.34M 1.53MB/s in 0.9s 2023-12-07 12:26:41 (1.53 MB/s) - 'kselftest.tar.xz' saved [1410472/1410472] skiplist: ======================================== ======================================== openat2:openat2_test openat2:resolve_test openat2:rename_attack_test ============== Tests to run =============== openat2:openat2_test openat2:resolve_test openat2:rename_attack_test ===========End Tests to run =============== shardfile-openat2 pass <12>[ 63.663921] kselftest: Running tests in openat2 TAP version 13 1..3 # selftests: openat2: openat2_test # ./openat2_test: error while loading shared libraries: libasan.so.6: cannot open shared object file: No such file or directory not ok 1 selftests: openat2: openat2_test # exit=127 # selftests: openat2: resolve_test # ./resolve_test: error while loading shared libraries: libasan.so.6: cannot open shared object file: No such file or directory not ok 2 selftests: openat2: resolve_test # exit=127 # selftests: openat2: rename_attack_test # ./rename_attack_test: error while loading shared libraries: libasan.so.6: cannot open shared object file: No such file or directory not ok 3 selftests: openat2: rename_attack_test # exit=127 openat2_openat2_test fail openat2_resolve_test fail openat2_rename_attack_test fail + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #