Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1044112/tftp-deploy-m5s7vpjx/kernel/zImage tftp 0x82000000 1044112/tftp-deploy-m5s7vpjx/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1044112/tftp-deploy-m5s7vpjx/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.3 MiB/s done Bytes transferred = 4614144 (466800 hex) => tftp 0x83000000 1044112/tftp-deploy-m5s7vpjx/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1044112/tftp-deploy-m5s7vpjx/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1044112/tftp-deploy-m5s7vpjx/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.4 MiB/s done Bytes transferred = 14175093 (d84b75 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1044112/tftp-deploy-m5s7vpjx/dtb/am335x-boneblack.dtb tftp 0x88000000 1044112/tftp-deploy-m5s7vpjx/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1044112/tftp-deploy-m5s7vpjx/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-11-24 0:02:24 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14175029 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip41-rt17 (KernelCI@build-j21812-arm-gcc-10-omap2plus-defconfig-98bg4) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Nov 23 22:55:16 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] On node 0 totalpages: 130560 [ 0.000000] Normal zone: 1148 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 130560 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s33484 r8192 d23860 u65536 [ 0.000000] pcpu-alloc: s33484 r8192 d23860 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472028K/522240K available (9216K kernel code, 1044K rwdata, 2180K rodata, 1024K init, 272K bss, 33828K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008339] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018550] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030213] Console: colour dummy device 80x30 <3>[ 0.035091] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042147] This ensures that you still see kernel messages. Please <3>[ 0.048870] update your kernel commandline. <6>[ 0.053470] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095550] CPU: Testing write buffer coherency: ok <6>[ 0.100928] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106393] pid_max: default: 32768 minimum: 301 <6>[ 0.111559] LSM: Security Framework initializing <6>[ 0.116653] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124469] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134122] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140663] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147864] rcu: Hierarchical SRCU implementation. <6>[ 0.153643] smp: Bringing up secondary CPUs ... <6>[ 0.158578] smp: Brought up 1 node, 1 CPU <6>[ 0.163002] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169734] CPU: All CPU(s) started in SVC mode. <6>[ 0.175470] devtmpfs: initialized <6>[ 0.191326] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199862] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210304] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218933] pinctrl core: initialized pinctrl subsystem <6>[ 0.226497] NET: Registered protocol family 16 <6>[ 0.234155] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260908] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.267011] audit: initializing netlink subsys (disabled) <6>[ 0.274076] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.274090] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.274095] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.274358] cpuidle: using governor menu <5>[ 1.163576] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.288589] No ATAGs? <6>[ 1.291267] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.315654] Kprobes globally optimized <7>[ 1.325933] reg-fixed-voltage fixedregulator0: GPIO lookup for consumer (null) <7>[ 1.333792] reg-fixed-voltage fixedregulator0: using device tree for GPIO lookup <7>[ 1.341721] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/fixedregulator0[0]' <7>[ 1.351075] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator0[0]' <7>[ 1.360322] reg-fixed-voltage fixedregulator0: using lookup tables for GPIO lookup <7>[ 1.368381] reg-fixed-voltage fixedregulator0: No GPIO consumer (null) found <6>[ 1.378630] iommu: Default domain type: Translated <6>[ 1.385706] vgaarb: loaded <5>[ 1.389404] SCSI subsystem initialized <7>[ 1.394167] libata version 3.00 loaded. <6>[ 1.399039] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.404422] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.414141] PTP clock support registered <6>[ 1.419731] clocksource: Switched to clocksource dmtimer <5>[ 2.059481] VFS: Disk quotas dquot_6.6.0 <6>[ 2.063985] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.080841] NET: Registered protocol family 2 <6>[ 2.085915] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.094617] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.103583] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.111880] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.119543] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.126476] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.133509] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.141132] NET: Registered protocol family 1 <6>[ 2.146944] RPC: Registered named UNIX socket transport module. <6>[ 2.153415] RPC: Registered udp transport module. <6>[ 2.158523] RPC: Registered tcp transport module. <6>[ 2.163646] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.170573] PCI: CLS 0 bytes, default 64 <6>[ 2.175609] Trying to unpack rootfs image as initramfs... <6>[ 3.161860] Freeing initrd memory: 13844K <6>[ 3.167532] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.177957] Initialise system trusted keyrings <6>[ 3.183402] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.191641] NFS: Registering the id_resolver key type <5>[ 3.197185] Key type id_resolver registered <5>[ 3.201829] Key type id_legacy registered <6>[ 3.206279] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.214259] Key type asymmetric registered <5>[ 3.218754] Asymmetric key parser 'x509' registered <6>[ 3.224091] io scheduler mq-deadline registered <6>[ 3.229021] io scheduler kyber registered <3>[ 3.367193] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.375904] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.484897] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.527009] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.598830] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.607543] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.667466] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.676175] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.693728] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.702416] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.766045] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.774610] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.802234] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <7>[ 3.811167] gpio-clk clk_mcasp0: GPIO lookup for consumer enable <7>[ 3.817640] gpio-clk clk_mcasp0: using device tree for GPIO lookup <7>[ 3.824360] gpio-clk clk_mcasp0: No GPIO consumer enable found <6>[ 3.836186] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <7>[ 3.846981] omap8250 44e09000.serial: GPIO lookup for consumer rs485-term <7>[ 3.854400] omap8250 44e09000.serial: using device tree for GPIO lookup <7>[ 3.861526] of_get_named_gpiod_flags: can't parse 'rs485-term-gpios' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.876612] of_get_named_gpiod_flags: can't parse 'rs485-term-gpio' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.891599] omap8250 44e09000.serial: using lookup tables for GPIO lookup <7>[ 3.898852] omap8250 44e09000.serial: No GPIO consumer rs485-term found <6>[ 3.905984] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.915401] printk: console [ttyS0] enabled <6>[ 3.915401] printk: console [ttyS0] enabled <6>[ 3.924464] printk: bootconsole [omap8250] disabled <6>[ 3.924464] printk: bootconsole [omap8250] disabled <6>[ 3.948368] brd: module loaded <6>[ 3.959074] loop: module loaded <3>[ 3.964693] mtdoops: mtd device (mtddev=name/number) must be supplied <7>[ 3.973784] mdio_bus fixed-0: GPIO lookup for consumer reset <7>[ 3.979841] mdio_bus fixed-0: using lookup tables for GPIO lookup <7>[ 3.986227] mdio_bus fixed-0: No GPIO consumer reset found <7>[ 3.996498] mdio_bus 4a101000.mdio: GPIO lookup for consumer reset <7>[ 4.003141] mdio_bus 4a101000.mdio: using device tree for GPIO lookup <7>[ 4.009917] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 4.024992] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 4.039971] mdio_bus 4a101000.mdio: using lookup tables for GPIO lookup <7>[ 4.046880] mdio_bus 4a101000.mdio: No GPIO consumer reset found <6>[ 4.109692] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <7>[ 4.151177] mdio_bus 4a101000.mdio:00: GPIO lookup for consumer reset <7>[ 4.157957] mdio_bus 4a101000.mdio:00: using device tree for GPIO lookup <7>[ 4.165059] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 4.181474] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 4.197768] mdio_bus 4a101000.mdio:00: using lookup tables for GPIO lookup <7>[ 4.204957] mdio_bus 4a101000.mdio:00: No GPIO consumer reset found <6>[ 4.212798] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.222704] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.229361] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.235164] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.242753] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.251790] i2c /dev entries driver <5>[ 4.257281] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.265224] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.271773] sdhci: Copyright(c) Pierre Ossman <6>[ 4.277122] sdhci-pltfm: SDHCI platform and OF driver helper <7>[ 4.284159] sdhci-omap 48060000.mmc: GPIO lookup for consumer cd <7>[ 4.290571] sdhci-omap 48060000.mmc: using device tree for GPIO lookup <7>[ 4.297419] sdhci-omap 48060000.mmc: No GPIO consumer cd found <7>[ 4.304446] sdhci-omap 481d8000.mmc: GPIO lookup for consumer wp <7>[ 4.310852] sdhci-omap 481d8000.mmc: using device tree for GPIO lookup <7>[ 4.317686] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.331586] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.345348] sdhci-omap 481d8000.mmc: using lookup tables for GPIO lookup <7>[ 4.352361] sdhci-omap 481d8000.mmc: No GPIO consumer wp found <4>[ 4.358649] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.367149] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.375486] Initializing XFRM netlink socket <6>[ 4.380327] NET: Registered protocol family 10 <6>[ 4.386557] Segment Routing with IPv6 <6>[ 4.390697] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.397663] NET: Registered protocol family 17 <6>[ 4.402501] NET: Registered protocol family 15 <5>[ 4.407331] Key type dns_resolver registered <6>[ 4.412527] oprofile: using arm/armv7 <6>[ 4.416574] ThumbEE CPU extension supported. <5>[ 4.421214] Registering SWP/SWPB emulation handler <3>[ 4.426687] omap_voltage_late_init: Voltage driver support not added <3>[ 4.433402] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.441835] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.450511] SmartReflex Class3 initialized <6>[ 4.457142] printk: console [ttyS0]: printing thread started <5>[ 4.457225] Loading compiled-in X.509 certificates <6>[ 4.476409] OMAP GPIO hardware version 0.1 <6>[ 4.492949] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <4>[ 4.520395] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.527875] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.542496] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.543248] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.547181] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.570215] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.570226] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.570488] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.578136] mmc1: new high speed MMC card at address 0001 <6>[ 4.579229] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.579809] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.580283] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.580618] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.634752] mmcblk1: p1 <6>[ 4.648216] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.649897] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.741239] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.890370] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.919712] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.949813] Sending DHCP requests ., OK <6>[ 7.989685] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 7.989706] IP-Config: Complete: <6>[ 7.989710] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.989724] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.989730] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.989737] nameserver0=192.168.11.1 <6>[ 7.992365] Freeing unused kernel memory: 1024K <6>[ 8.050189] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.286556] udevd[101]: starting version 3.2.9 <5>[ 8.288034] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.288449] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.288588] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.324938] udevd[101]: specified user 'tss' unknown <27>[ 8.325154] udevd[101]: specified group 'tss' unknown <30>[ 8.332681] udevd[102]: starting eudev-3.2.9 <4>[ 9.134683] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.135016] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 9.196341] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.196689] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.216377] usbcore: registered new interface driver usbfs <6>[ 9.216470] usbcore: registered new interface driver hub <6>[ 9.216556] usbcore: registered new device driver usb <6>[ 9.267557] remoteproc remoteproc0: wkup_m3 is available <6>[ 9.666713] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.666763] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.780186] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.780218] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.780227] usb usb1: Product: MUSB HDRC host driver <6>[ 9.780235] usb usb1: Manufacturer: Linux 5.10.201-cip41-rt17 musb-hcd <6>[ 9.780241] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.790761] hub 1-0:1.0: USB hub found <6>[ 9.791522] hub 1-0:1.0: 1 port detected <6>[ 9.920238] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 9.940542] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 9.940615] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <3>[ 10.318851] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 10.433384] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 10.519961] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 10.520458] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 10.580454] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 10.624298] at24 2-0056: supply vcc not found, using dummy regulator <3>[ 10.653129] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 10.666062] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <3>[ 10.729869] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.780458] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <4>[ 10.792762] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 10.799527] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 10.872566] davinci-mcasp 48038000.mcasp: IRQ common not found <3>[ 10.971801] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 11.052803] tda998x 0-0070: found TDA19988 <3>[ 11.083250] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 11.311963] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 11.370189] remoteproc remoteproc0: powering up wkup_m3 <4>[ 11.370345] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 11.370364] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 11.370373] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 12.057810] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 12.064254] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 12.066892] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 12.078004] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 12.117690] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 12.118707] random: crng init done <3>[ 12.355718] PM: Cannot get wkup_m3_ipc handle <6>[ 12.502786] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.523162] omap-sham 53100000.sham: will run requests pump with realtime priority <3>[ 12.659943] PM: Cannot get wkup_m3_ipc handle <6>[ 12.672998] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.678968] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 12.705541] PM: Cannot get wkup_m3_ipc handle <3>[ 13.284828] PM: Cannot get wkup_m3_ipc handle <3>[ 13.304130] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1044112/environment . /lava-1044112/environment / # /lava-1044112/bin/lava-test-runner /lava-1044112/0 /lava-1044112/bin/lava-test-runner /lava-1044112/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1044112/0/tests/0_dmesg + cat uuid + UUID=1044112_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.206393] <8>[ 14.274652] <8>[ 14.334895] + set +x <8>[ 14.395766] <8>[ 14.397846] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1044112/environment / # . /lava-1044112/environment/lava-1044112/bin/lava-test-runner /lava-1044112/1 / # /lava-1044112/bin/lava-test-runner /lava-1044112/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1044112/1/tests/1_bootrr + cat uuid + UUID=1044112_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lav<8>[ 14.947000] a-1044112/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto pm33xx /lava-1044112/1/../bin/lava-test-case <8>[ 16.058160] /lava-1044112/1/../bin/lava-test-case <8>[ 16.113265] /lava-1044112/1/../bin/lava-test-case <8>[ 16.146201] /lava-1044112/1/../bin/lava-test-case <8>[ 16.207976] /lava-1044112/1/../bin/lava-test-case <8>[ 16.259158] /lava-1044112/1/../bin/lava-test-case <8>[ 16.300636] /lava-1044112/1/../bin/lava-test-case <8>[ 16.351961] /lava-1044112/1/../bin/lava-test-case <8>[ 16.418517] /lava-1044112/1/../bin/lava-test-case <8>[ 16.459583] /lava-1044112/1/../bin/lava-test-case <8>[ 16.510231] /lava-1044112/1/../bin/lava-test-case <8>[ 16.550915] /lava-1044112/1/../bin/lava-test-case <8>[ 16.601935] /lava-1044112/1/../bin/lava-test-case <8>[ 16.642199] /lava-1044112/1/../bin/lava-test-case <8>[ 16.682270] /lava-1044112/1/../bin/lava-test-case <8>[ 16.723848] /lava-1044112/1/../bin/lava-test-case <8>[ 16.774200] /lava-1044112/1/../bin/lava-test-case <8>[ 16.815856] /lava-1044112/1/../bin/lava-test-case <8>[ 16.867339] /lava-1044112/1/../bin/lava-test-case <8>[ 16.917007] /lava-1044112/1/../bin/lava-test-case <8>[ 16.957915] /lava-1044112/1/../bin/lava-test-case <8>[ 17.009043] /lava-1044112/1/../bin/lava-test-case <8>[ 17.060317] /lava-1044112/1/../bin/lava-test-case <8>[ 17.101381] /lava-1044112/1/../bin/lava-test-case <8>[ 17.152810] /lava-1044112/1/../bin/lava-test-case <8>[ 17.194082] /lava-1044112/1/../bin/lava-test-case <8>[ 17.244642] /lava-1044112/1/../bin/lava-test-case <8>[ 17.285354] /lava-1044112/1/../bin/lava-test-case <8>[ 18.367996] /lava-1044112/1/../bin/lava-test-case <8>[ 18.409354] /lava-1044112/1/../bin/lava-test-case <8>[ 18.460836] /lava-1044112/1/../bin/lava-test-case <8>[ 18.502379] /lava-1044112/1/../bin/lava-test-case <8>[ 18.553232] /lava-1044112/1/../bin/lava-test-case <8>[ 18.593860] /lava-1044112/1/../bin/lava-test-case <8>[ 18.644499] /lava-1044112/1/../bin/lava-test-case <8>[ 18.685177] /lava-1044112/1/../bin/lava-test-case <8>[ 18.736349] /lava-1044112/1/../bin/lava-test-case <8>[ 18.776948] /lava-1044112/1/../bin/lava-test-case <8>[ 18.827757] /lava-1044112/1/../bin/lava-test-case <8>[ 18.868726] /lava-1044112/1/../bin/lava-test-case <8>[ 18.920083] /lava-1044112/1/../bin/lava-test-case <8>[ 18.960704] /lava-1044112/1/../bin/lava-test-case <8>[ 19.011621] /lava-1044112/1/../bin/lava-test-case <8>[ 19.052489] /lava-1044112/1/../bin/lava-test-case <8>[ 19.103324] /lava-1044112/1/../bin/lava-test-case <8>[ 19.143968] /lava-1044112/1/../bin/lava-test-case <8>[ 19.194720] /lava-1044112/1/../bin/lava-test-case <8>[ 19.235695] /lava-1044112/1/../bin/lava-test-case <8>[ 19.286735] /lava-1044112/1/../bin/lava-test-case /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: <8>[ 19.327748] line 84: assert_device-present: not found /lava-1044112/1/../bin/lava-test-case <8>[ 19.374558] /lava-1044112/1/../bin/lava-test-case <8>[ 19.425534] /lava-1044112/1/../bin/lava-test-case <8>[ 19.473993] + set +x