Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.2 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1088606/tftp-deploy-pcpqun2u/kernel/zImage tftp 0x82000000 1088606/tftp-deploy-pcpqun2u/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1088606/tftp-deploy-pcpqun2u/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 5.1 MiB/s done Bytes transferred = 4608448 (4651c0 hex) => tftp 0x83000000 1088606/tftp-deploy-pcpqun2u/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1088606/tftp-deploy-pcpqun2u/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1088606/tftp-deploy-pcpqun2u/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.2 MiB/s done Bytes transferred = 14175143 (d84ba7 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1088606/tftp-deploy-pcpqun2u/dtb/am335x-boneblack.dtb tftp 0x88000000 1088606/tftp-deploy-pcpqun2u/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1088606/tftp-deploy-pcpqun2u/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 5 MiB/s done Bytes transferred = 62861 (f58d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-02-05 14:34:25 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14175079 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801258c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.209-cip44 (KernelCI@build-j98718-arm-gcc-10-omap2plus-defconfig-nr758) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Feb 5 13:58:33 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472024K/522240K available (9216K kernel code, 1027K rwdata, 2176K rodata, 1024K init, 278K bss, 33832K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008343] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018567] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030224] Console: colour dummy device 80x30 <3>[ 0.035094] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042154] This ensures that you still see kernel messages. Please <3>[ 0.048880] update your kernel commandline. <6>[ 0.053480] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095547] CPU: Testing write buffer coherency: ok <6>[ 0.100928] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106393] pid_max: default: 32768 minimum: 301 <6>[ 0.111551] LSM: Security Framework initializing <6>[ 0.116651] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124465] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134126] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140640] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147841] rcu: Hierarchical SRCU implementation. <6>[ 0.153626] smp: Bringing up secondary CPUs ... <6>[ 0.158562] smp: Brought up 1 node, 1 CPU <6>[ 0.162991] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169720] CPU: All CPU(s) started in SVC mode. <6>[ 0.175447] devtmpfs: initialized <6>[ 0.191011] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199611] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210051] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218560] pinctrl core: initialized pinctrl subsystem <6>[ 0.226220] NET: Registered protocol family 16 <6>[ 0.233928] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260398] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266484] audit: initializing netlink subsys (disabled) <6>[ 0.273542] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273557] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280163] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.286901] cpuidle: using governor menu <5>[ 1.147498] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.270238] No ATAGs? <6>[ 1.272865] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.297008] Kprobes globally optimized <6>[ 1.310303] iommu: Default domain type: Translated <6>[ 1.317354] vgaarb: loaded <5>[ 1.321054] SCSI subsystem initialized <6>[ 1.326344] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.331836] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.341564] PTP clock support registered <6>[ 1.347119] clocksource: Switched to clocksource dmtimer <5>[ 1.985578] VFS: Disk quotas dquot_6.6.0 <6>[ 1.990087] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.006656] NET: Registered protocol family 2 <6>[ 2.011836] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.020497] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.029454] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.037749] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.045408] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.052352] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.059383] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.066985] NET: Registered protocol family 1 <6>[ 2.072766] RPC: Registered named UNIX socket transport module. <6>[ 2.079221] RPC: Registered udp transport module. <6>[ 2.084328] RPC: Registered tcp transport module. <6>[ 2.089456] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.096362] PCI: CLS 0 bytes, default 64 <6>[ 2.101413] Trying to unpack rootfs image as initramfs... <6>[ 3.088362] Freeing initrd memory: 13844K <6>[ 3.094024] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.104420] Initialise system trusted keyrings <6>[ 3.109813] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.118062] NFS: Registering the id_resolver key type <5>[ 3.123611] Key type id_resolver registered <5>[ 3.128252] Key type id_legacy registered <6>[ 3.132705] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.140696] Key type asymmetric registered <5>[ 3.145189] Asymmetric key parser 'x509' registered <6>[ 3.150537] io scheduler mq-deadline registered <6>[ 3.155468] io scheduler kyber registered <3>[ 3.291116] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.299815] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.406750] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.448417] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.519029] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.527729] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.586655] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.595373] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.612692] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.621380] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.683983] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.692548] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.719371] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.733899] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.744788] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.754218] printk: console [ttyS0] enabled <6>[ 3.754218] printk: console [ttyS0] enabled <6>[ 3.763286] printk: bootconsole [omap8250] disabled <6>[ 3.763286] printk: bootconsole [omap8250] disabled <6>[ 3.786917] brd: module loaded <6>[ 3.797720] loop: module loaded <3>[ 3.803198] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.867117] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.909801] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.919723] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.926378] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.932218] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.939777] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 3.948822] i2c /dev entries driver <5>[ 3.954348] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 3.962294] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.968838] sdhci: Copyright(c) Pierre Ossman <6>[ 3.974206] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 3.982504] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.992290] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.000768] Initializing XFRM netlink socket <6>[ 4.005571] NET: Registered protocol family 10 <6>[ 4.012025] Segment Routing with IPv6 <6>[ 4.016078] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.023141] NET: Registered protocol family 17 <6>[ 4.027996] NET: Registered protocol family 15 <5>[ 4.032832] Key type dns_resolver registered <6>[ 4.038027] oprofile: using arm/armv7 <6>[ 4.042070] ThumbEE CPU extension supported. <5>[ 4.046633] Registering SWP/SWPB emulation handler <3>[ 4.052191] omap_voltage_late_init: Voltage driver support not added <3>[ 4.058909] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.067324] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.075988] SmartReflex Class3 initialized <6>[ 4.080947] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.089863] Loading compiled-in X.509 certificates <6>[ 4.114870] OMAP GPIO hardware version 0.1 <4>[ 4.147799] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.161438] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.170202] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.176548] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.186444] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.197928] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.206942] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.212173] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.225413] mmc1: new high speed MMC card at address 0001 <6>[ 4.232277] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.237854] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.244515] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.251119] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.260625] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.269609] mmcblk1: p1 <6>[ 4.277855] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.368646] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.487752] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.507093] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.537224] Sending DHCP requests ., OK <6>[ 7.581200] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.2 <6>[ 7.589274] IP-Config: Complete: <6>[ 7.592783] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.2, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.603281] host=192.168.11.2, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.610311] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.610318] nameserver0=192.168.11.1 <6>[ 7.623766] Freeing unused kernel memory: 1024K <6>[ 7.647565] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.883348] udevd[100]: starting version 3.2.9 <5>[ 7.890116] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.898042] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.904940] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.922385] udevd[100]: specified user 'tss' unknown <27>[ 7.928292] udevd[100]: specified group 'tss' unknown <30>[ 7.939827] udevd[101]: starting eudev-3.2.9 <6>[ 8.829767] remoteproc remoteproc0: wkup_m3 is available <4>[ 8.860032] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.869236] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 8.926712] usbcore: registered new interface driver usbfs <6>[ 8.932736] usbcore: registered new interface driver hub <6>[ 8.938482] usbcore: registered new device driver usb <4>[ 9.056714] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.065911] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.262010] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.267835] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.497325] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.505922] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.513494] usb usb1: Product: MUSB HDRC host driver <6>[ 9.518780] usb usb1: Manufacturer: Linux 5.10.209-cip44 musb-hcd <6>[ 9.525164] usb usb1: SerialNumber: musb-hdrc.1 <4>[ 9.595870] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 9.765975] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 9.773735] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 9.792727] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <3>[ 9.884109] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.908694] hub 1-0:1.0: USB hub found <6>[ 9.934514] hub 1-0:1.0: 1 port detected <6>[ 9.939521] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <4>[ 9.979732] at24 2-0055: supply vcc not found, using dummy regulator <6>[ 10.035206] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 10.040766] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <4>[ 10.072771] at24 2-0056: supply vcc not found, using dummy regulator <6>[ 10.091083] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 10.140593] tda998x 0-0070: found TDA19988 <4>[ 10.171385] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 10.292643] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.662256] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 10.689608] remoteproc remoteproc0: powering up wkup_m3 <4>[ 10.695282] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 10.705208] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 10.711453] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <3>[ 10.813390] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 11.443402] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 11.450630] random: crng init done <6>[ 11.464302] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 11.510527] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 11.549901] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 11.560707] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 11.893138] PM: Cannot get wkup_m3_ipc handle <6>[ 12.031646] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.056322] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.109793] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 12.123540] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 12.230835] PM: Cannot get wkup_m3_ipc handle <3>[ 12.254556] PM: Cannot get wkup_m3_ipc handle <3>[ 12.733364] PM: Cannot get wkup_m3_ipc handle <3>[ 12.763974] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1088606/environment . /lava-1088606/environment / # /lava-1088606/bin/lava-test-runner /lava-1088606/0 /lava-1088606/bin/lava-test-runner /lava-1088606/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1088606/0/tests/0_dmesg + cat uuid + UUID=1088606_1.5.2.4.1 <8>[ 13.692151] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 13.758152] <8>[ 13.818172] <8>[ 13.878221] + set +x <8>[ 13.889759] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1088606/environment / # . /lava-1088606/environment/lava-1088606/bin/lava-test-runner /lava-1088606/1 / # /lava-1088606/bin/lava-test-runner /lava-1088606/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1088606/1/tests/1_bootrr + cat uuid + UUID=1088606_1.5.2.4.5 + <8>[ 14.416309] set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1088606/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto pm33xx /lava-1088606/1/../bin/lava-test-case <8>[ 15.523969] /lava-1088606/1/../bin/lava-test-case <8>[ 15.579332] /lava-1088606/1/../bin/lava-test-case <8>[ 15.612107] /lava-1088606/1/../bin/lava-test-case <8>[ 15.673641] /lava-1088606/1/../bin/lava-test-case <8>[ 15.724869] /lava-1088606/1/../bin/lava-test-case <8>[ 15.765785] /lava-1088606/1/../bin/lava-test-case <8>[ 15.816670] /lava-1088606/1/../bin/lava-test-case <8>[ 15.866639] /lava-1088606/1/../bin/lava-test-case <8>[ 15.923969] /lava-1088606/1/../bin/lava-test-case <8>[ 15.974830] /lava-1088606/1/../bin/lava-test-case <8>[ 16.015590] /lava-1088606/1/../bin/lava-test-case <8>[ 16.066351] /lava-1088606/1/../bin/lava-test-case <8>[ 16.106568] /lava-1088606/1/../bin/lava-test-case <8>[ 16.147474] /lava-1088606/1/../bin/lava-test-case <8>[ 16.188238] /lava-1088606/1/../bin/lava-test-case <8>[ 16.238015] /lava-1088606/1/../bin/lava-test-case <8>[ 16.279557] /lava-1088606/1/../bin/lava-test-case <8>[ 16.330377] /lava-1088606/1/../bin/lava-test-case <8>[ 16.380441] /lava-1088606/1/../bin/lava-test-case <8>[ 16.420851] /lava-1088606/1/../bin/lava-test-case <8>[ 16.471725] /lava-1088606/1/../bin/lava-test-case <8>[ 16.522491] /lava-1088606/1/../bin/lava-test-case <8>[ 16.564373] /lava-1088606/1/../bin/lava-test-case <8>[ 16.615622] /lava-1088606/1/../bin/lava-test-case <8>[ 16.656899] /lava-1088606/1/../bin/lava-test-case <8>[ 16.707647] /lava-1088606/1/../bin/lava-test-case <8>[ 16.748128] /lava-1088606/1/../bin/lava-test-case <8>[ 17.827364] /lava-1088606/1/../bin/lava-test-case <8>[ 17.868742] /lava-1088606/1/../bin/lava-test-case <8>[ 17.919742] /lava-1088606/1/../bin/lava-test-case <8>[ 17.960888] /lava-1088606/1/../bin/lava-test-case <8>[ 18.011462] /lava-1088606/1/../bin/lava-test-case <8>[ 18.052030] /lava-1088606/1/../bin/lava-test-case <8>[ 18.102871] /lava-1088606/1/../bin/lava-test-case <8>[ 18.144126] /lava-1088606/1/../bin/lava-test-case <8>[ 18.195042] /lava-1088606/1/../bin/lava-test-case <8>[ 18.236063] /lava-1088606/1/../bin/lava-test-case <8>[ 18.287579] /lava-1088606/1/../bin/lava-test-case <8>[ 18.328138] /lava-1088606/1/../bin/lava-test-case <8>[ 18.378959] /lava-1088606/1/../bin/lava-test-case <8>[ 18.419486] /lava-1088606/1/../bin/lava-test-case <8>[ 18.470568] /lava-1088606/1/../bin/lava-test-case <8>[ 18.511353] /lava-1088606/1/../bin/lava-test-case <8>[ 18.562082] /lava-1088606/1/../bin/lava-test-case <8>[ 18.602465] /lava-1088606/1/../bin/lava-test-case <8>[ 18.652910] /lava-1088606/1/../bin/lava-test-case <8>[ 18.694313] /lava-1088606/1/../bin/lava-test-case <8>[ 18.744434] /lava-1088606/1/../bin/lava-test-case <8>[ 18.785447] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-1088606/1/../bin/lava-test-case <8>[ 18.828286] /lava-1088606/1/../bin/lava-test-case <8>[ 18.879144] /lava-1088606/1/../bin/lava-test-case <8>[ 18.926950] + set +x <8>[ 18.943913] / #