Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'.  U-Boot SPL 2020.10 (Apr 28 2023 - 11:09:01 +0100) Trying to boot from MMC2 U-Boot 2020.10 (Apr 28 2023 - 11:09:01 +0100) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... Unable to use mmc 1:1... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.1.91 (1077 ms) => setenv serverip 192.168.1.1 setenv serverip 192.168.1.1 => tftp 0x82000000 1122224/tftp-deploy-_rrsb9lu/kernel/zImage tftp 0x82000000 1122224/tftp-deploy-_rrsb9lu/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.91 Filename '1122224/tftp-deploy-_rrsb9lu/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 2.1 MiB/s done Bytes transferred = 4616936 (4672e8 hex) => tftp 0x83000000 1122224/tftp-deploy-_rrsb9lu/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1122224/tftp-deploy-_rrsb9lu/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.91 Filename '1122224/tftp-deploy-_rrsb9lu/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 2.1 MiB/s done Bytes transferred = 14169506 (d835a2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1122224/tftp-deploy-_rrsb9lu/dtb/am335x-boneblack.dtb tftp 0x88000000 1122224/tftp-deploy-_rrsb9lu/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.91 Filename '1122224/tftp-deploy-_rrsb9lu/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 1.9 MiB/s done Bytes transferred = 62861 (f58d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-04-19 17:44:26 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14169442 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801258c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.214-cip46-rt19 (KernelCI@build-j171793-arm-gcc-10-omap2plus-defconfig-vdv6n) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Apr 19 17:21:01 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] On node 0 totalpages: 130560 [ 0.000000] Normal zone: 1148 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 130560 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s33484 r8192 d23860 u65536 [ 0.000000] pcpu-alloc: s33484 r8192 d23860 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472032K/522240K available (9216K kernel code, 1044K rwdata, 2180K rodata, 1024K init, 272K bss, 33824K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008338] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018547] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030229] Console: colour dummy device 80x30 <3>[ 0.035103] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042161] This ensures that you still see kernel messages. Please <3>[ 0.048885] update your kernel commandline. <6>[ 0.053486] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095547] CPU: Testing write buffer coherency: ok <6>[ 0.100925] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106391] pid_max: default: 32768 minimum: 301 <6>[ 0.111554] LSM: Security Framework initializing <6>[ 0.116650] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124470] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134120] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140638] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147848] rcu: Hierarchical SRCU implementation. <6>[ 0.153627] smp: Bringing up secondary CPUs ... <6>[ 0.158564] smp: Brought up 1 node, 1 CPU <6>[ 0.162992] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169724] CPU: All CPU(s) started in SVC mode. <6>[ 0.175448] devtmpfs: initialized <6>[ 0.191382] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199924] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210362] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218962] pinctrl core: initialized pinctrl subsystem <6>[ 0.226516] NET: Registered protocol family 16 <6>[ 0.234152] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260588] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266666] audit: initializing netlink subsys (disabled) <6>[ 0.273730] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273744] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.273750] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.274015] cpuidle: using governor menu <5>[ 1.152703] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.276158] No ATAGs? <6>[ 1.278789] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.303121] Kprobes globally optimized <7>[ 1.313492] reg-fixed-voltage fixedregulator0: GPIO lookup for consumer (null) <7>[ 1.321358] reg-fixed-voltage fixedregulator0: using device tree for GPIO lookup <7>[ 1.329281] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/fixedregulator0[0]' <7>[ 1.338617] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator0[0]' <7>[ 1.347864] reg-fixed-voltage fixedregulator0: using lookup tables for GPIO lookup <7>[ 1.355938] reg-fixed-voltage fixedregulator0: No GPIO consumer (null) found <6>[ 1.366259] iommu: Default domain type: Translated <6>[ 1.373359] vgaarb: loaded <5>[ 1.376934] SCSI subsystem initialized <7>[ 1.381767] libata version 3.00 loaded. <6>[ 1.386534] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.392008] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.401731] PTP clock support registered <6>[ 1.407267] clocksource: Switched to clocksource dmtimer <5>[ 2.044629] VFS: Disk quotas dquot_6.6.0 <6>[ 2.049139] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.065747] NET: Registered protocol family 2 <6>[ 2.070933] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.079585] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.088549] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.096822] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.104505] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.111438] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.118470] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.126068] NET: Registered protocol family 1 <6>[ 2.131874] RPC: Registered named UNIX socket transport module. <6>[ 2.138346] RPC: Registered udp transport module. <6>[ 2.143454] RPC: Registered tcp transport module. <6>[ 2.148577] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.155483] PCI: CLS 0 bytes, default 64 <6>[ 2.160541] Trying to unpack rootfs image as initramfs... <6>[ 3.146235] Freeing initrd memory: 13840K <6>[ 3.152207] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.162662] Initialise system trusted keyrings <6>[ 3.168185] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.176334] NFS: Registering the id_resolver key type <5>[ 3.181978] Key type id_resolver registered <5>[ 3.186554] Key type id_legacy registered <6>[ 3.191026] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.199038] Key type asymmetric registered <5>[ 3.203534] Asymmetric key parser 'x509' registered <6>[ 3.208874] io scheduler mq-deadline registered <6>[ 3.213805] io scheduler kyber registered <3>[ 3.350197] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.358897] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.466310] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.508062] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.578938] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.587633] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.646830] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.655553] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.672904] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.681592] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.744483] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.753051] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.780138] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <7>[ 3.789136] gpio-clk clk_mcasp0: GPIO lookup for consumer enable <7>[ 3.795611] gpio-clk clk_mcasp0: using device tree for GPIO lookup <7>[ 3.802341] gpio-clk clk_mcasp0: No GPIO consumer enable found <6>[ 3.814190] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <7>[ 3.824972] omap8250 44e09000.serial: GPIO lookup for consumer rs485-term <7>[ 3.832373] omap8250 44e09000.serial: using device tree for GPIO lookup <7>[ 3.839507] of_get_named_gpiod_flags: can't parse 'rs485-term-gpios' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.854594] of_get_named_gpiod_flags: can't parse 'rs485-term-gpio' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.869580] omap8250 44e09000.serial: using lookup tables for GPIO lookup <7>[ 3.876835] omap8250 44e09000.serial: No GPIO consumer rs485-term found <6>[ 3.883966] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.893383] printk: console [ttyS0] enabled <6>[ 3.893383] printk: console [ttyS0] enabled <6>[ 3.902445] printk: bootconsole [omap8250] disabled <6>[ 3.902445] printk: bootconsole [omap8250] disabled <6>[ 3.926192] brd: module loaded <6>[ 3.936871] loop: module loaded <3>[ 3.942518] mtdoops: mtd device (mtddev=name/number) must be supplied <7>[ 3.951661] mdio_bus fixed-0: GPIO lookup for consumer reset <7>[ 3.957711] mdio_bus fixed-0: using lookup tables for GPIO lookup <7>[ 3.964099] mdio_bus fixed-0: No GPIO consumer reset found <7>[ 3.974384] mdio_bus 4a101000.mdio: GPIO lookup for consumer reset <7>[ 3.981020] mdio_bus 4a101000.mdio: using device tree for GPIO lookup <7>[ 3.987796] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 4.002870] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 4.017850] mdio_bus 4a101000.mdio: using lookup tables for GPIO lookup <7>[ 4.024759] mdio_bus 4a101000.mdio: No GPIO consumer reset found <6>[ 4.087227] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <7>[ 4.128318] mdio_bus 4a101000.mdio:00: GPIO lookup for consumer reset <7>[ 4.135096] mdio_bus 4a101000.mdio:00: using device tree for GPIO lookup <7>[ 4.142221] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 4.158636] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 4.174930] mdio_bus 4a101000.mdio:00: using lookup tables for GPIO lookup <7>[ 4.182118] mdio_bus 4a101000.mdio:00: No GPIO consumer reset found <6>[ 4.189974] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.199877] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.206537] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.212327] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.219914] cpsw 4a100000.ethernet: Detected MACID = f4:b8:98:ab:fa:84 <6>[ 4.228965] i2c /dev entries driver <5>[ 4.234486] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.242446] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.248993] sdhci: Copyright(c) Pierre Ossman <6>[ 4.254353] sdhci-pltfm: SDHCI platform and OF driver helper <7>[ 4.261382] sdhci-omap 48060000.mmc: GPIO lookup for consumer cd <7>[ 4.267792] sdhci-omap 48060000.mmc: using device tree for GPIO lookup <7>[ 4.274636] sdhci-omap 48060000.mmc: No GPIO consumer cd found <7>[ 4.281658] sdhci-omap 481d8000.mmc: GPIO lookup for consumer wp <7>[ 4.288057] sdhci-omap 481d8000.mmc: using device tree for GPIO lookup <7>[ 4.294891] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.308788] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.322544] sdhci-omap 481d8000.mmc: using lookup tables for GPIO lookup <7>[ 4.329558] sdhci-omap 481d8000.mmc: No GPIO consumer wp found <4>[ 4.335845] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.344369] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.352739] Initializing XFRM netlink socket <6>[ 4.357553] NET: Registered protocol family 10 <6>[ 4.363770] Segment Routing with IPv6 <6>[ 4.367905] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.374864] NET: Registered protocol family 17 <6>[ 4.379698] NET: Registered protocol family 15 <5>[ 4.384544] Key type dns_resolver registered <6>[ 4.389737] oprofile: using arm/armv7 <6>[ 4.393777] ThumbEE CPU extension supported. <5>[ 4.398414] Registering SWP/SWPB emulation handler <3>[ 4.403889] omap_voltage_late_init: Voltage driver support not added <3>[ 4.410606] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.419041] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.427711] SmartReflex Class3 initialized <6>[ 4.459714] printk: console [ttyS0]: printing thread started <5>[ 4.459801] Loading compiled-in X.509 certificates <6>[ 4.478915] OMAP GPIO hardware version 0.1 <6>[ 4.495414] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <4>[ 4.527940] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.535348] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.549951] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.550735] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.554665] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.559854] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.559865] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.560116] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.657936] mmc1: new high speed MMC card at address 0001 <6>[ 4.658988] mmcblk1: mmc1:0001 MK2704 3.53 GiB <6>[ 4.659426] mmcblk1boot0: mmc1:0001 MK2704 partition 1 2.00 MiB <6>[ 4.659822] mmcblk1boot1: mmc1:0001 MK2704 partition 2 2.00 MiB <6>[ 4.660163] mmcblk1rpmb: mmc1:0001 MK2704 partition 3 512 KiB, chardev (249:0) <6>[ 4.662279] mmcblk1: p1 <6>[ 4.701192] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.702635] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.818783] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.977911] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.997245] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.027371] Sending DHCP requests ., OK <6>[ 8.067225] IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.91 <6>[ 8.067246] IP-Config: Complete: <6>[ 8.067250] device=eth0, hwaddr=f4:b8:98:ab:fa:84, ipaddr=192.168.1.91, mask=255.255.255.0, gw=192.168.1.1 <6>[ 8.067264] host=192.168.1.91, domain=example.org, nis-domain=(none) <6>[ 8.067270] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.067277] nameserver0=192.168.1.1 <6>[ 8.069913] Freeing unused kernel memory: 1024K <6>[ 8.127735] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.359796] udevd[101]: starting version 3.2.9 <5>[ 8.361334] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.361736] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.361870] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.397910] udevd[101]: specified user 'tss' unknown <27>[ 8.398144] udevd[101]: specified group 'tss' unknown <30>[ 8.410235] udevd[102]: starting eudev-3.2.9 <4>[ 9.291378] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.291692] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 9.371572] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.371904] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.393582] usbcore: registered new interface driver usbfs <6>[ 9.393675] usbcore: registered new interface driver hub <6>[ 9.393762] usbcore: registered new device driver usb <6>[ 9.632558] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.632611] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.667663] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.667696] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.667705] usb usb1: Product: MUSB HDRC host driver <6>[ 9.667712] usb usb1: Manufacturer: Linux 5.10.214-cip46-rt19 musb-hcd <6>[ 9.667719] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.674576] hub 1-0:1.0: USB hub found <6>[ 9.674704] hub 1-0:1.0: 1 port detected <4>[ 9.825789] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 9.855170] remoteproc remoteproc0: wkup_m3 is available <6>[ 10.005356] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 10.005836] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 10.039984] at24 2-0055: supply vcc not found, using dummy regulator <6>[ 10.042329] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 10.044106] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 10.044172] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <4>[ 10.070024] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 10.100448] at24 2-0057: supply vcc not found, using dummy regulator <4>[ 10.380075] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 10.427438] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <3>[ 10.447469] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.576240] tda998x 0-0070: found TDA19988 <3>[ 10.610694] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 11.163981] davinci-mcasp 48038000.mcasp: IRQ common not found <3>[ 11.245080] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 11.283929] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 11.346986] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 11.375992] remoteproc remoteproc0: powering up wkup_m3 <4>[ 11.376146] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 11.376165] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 11.376173] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 12.151793] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 12.152346] random: crng init done <6>[ 12.187673] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 12.191941] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 12.192384] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 12.195245] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 12.303179] PM: Cannot get wkup_m3_ipc handle <6>[ 12.501193] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.512485] omap-sham 53100000.sham: will run requests pump with realtime priority <3>[ 12.579296] PM: Cannot get wkup_m3_ipc handle <6>[ 12.651335] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.679469] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 12.707968] PM: Cannot get wkup_m3_ipc handle <3>[ 13.218444] PM: Cannot get wkup_m3_ipc handle <3>[ 13.248246] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1122224/environment . /lava-1122224/environment / # /lava-1122224/bin/lava-test-runner /lava-1122224/0 /lava-1122224/bin/lava-test-runner /lava-1122224/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1122224/0/tests/0_dmesg + cat uuid + UUID=1122224_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.167638] <8>[ 14.232081] <8>[ 14.292509] + set +x <8>[ 14.353316] <8>[ 14.355387] / #