Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.64 (1254 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 469666/tftp-deploy-lp4gijog/kernel/Image tftp 0x82000000 469666/tftp-deploy-lp4gijog/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '469666/tftp-deploy-lp4gijog/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################### 14.6 MiB/s done Bytes transferred = 32055808 (1e92200 hex) => tftp 0x90080000 469666/tftp-deploy-lp4gijog/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 469666/tftp-deploy-lp4gijog/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '469666/tftp-deploy-lp4gijog/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 14.4 MiB/s done Bytes transferred = 18931266 (120de42 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 469666/tftp-deploy-lp4gijog/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 469666/tftp-deploy-lp4gijog/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.64; sending through gateway 172.16.0.254 Filename '469666/tftp-deploy-lp4gijog/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 6 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-06-11 11:22:10 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18931202 Bytes = 18.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.218-cip49-rt20 (KernelCI@build-j224642-arm64-gcc-10-defconfig-rsvbd) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue Jun 11 11:02:04 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7feb00-0x20ff800fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0 totalpages: 1031680 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 507392 pages, LIFO batch:63 [ 0.000000] Normal zone: 8192 pages used for memmap [ 0.000000] Normal zone: 524288 pages, LIFO batch:63 [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 19 pages/cpu s40408 r8192 d29224 u77824 [ 0.000000] pcpu-alloc: s40408 r8192 d29224 u77824 alloc=19*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3897580K/4126720K available (14592K kernel code, 2888K rwdata, 7680K rodata, 6016K init, 504K bss, 196372K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008715] Console: colour dummy device 80x25 <6>[ 0.013507] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024224] pid_max: default: 32768 minimum: 301 <6>[ 0.029181] LSM: Security Framework initializing <6>[ 0.034147] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041904] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050951] rcu: Hierarchical SRCU implementation. <6>[ 0.056188] Platform MSI: gic-its@6020000 domain created <6>[ 0.061879] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069740] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075864] EFI services will not be available. <6>[ 0.080798] smp: Bringing up secondary CPUs ... <6>[ 0.085890] Detected PIPT I-cache on CPU1 <6>[ 0.090213] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.097418] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.104991] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.111898] smp: Brought up 1 node, 2 CPUs <6>[ 0.116308] SMP: Total of 2 processors activated. <6>[ 0.121320] CPU features: detected: 32-bit EL0 Support <6>[ 0.126778] CPU features: detected: CRC32 instructions <6>[ 0.132229] CPU features: detected: 32-bit EL1 Support <6>[ 0.148816] CPU: All CPU(s) started at EL2 <6>[ 0.153233] alternatives: patching kernel code <6>[ 0.158712] devtmpfs: initialized <4>[ 0.164357] KASLR disabled due to lack of seed <6>[ 0.169213] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.179323] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.187004] pinctrl core: initialized pinctrl subsystem <6>[ 0.193179] DMI not present or invalid. <6>[ 0.197691] NET: Registered protocol family 16 <6>[ 0.203206] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210694] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218948] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.227226] audit: initializing netlink subsys (disabled) <5>[ 0.233055] audit: type=2000 audit(0.156:1): state=initialized audit_enabled=0 res=1 <6>[ 0.233589] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.233592] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.241147] cpuidle: using governor menu <6>[ 0.258637] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.265776] ASID allocator initialised with 65536 entries <6>[ 0.272169] Serial: AMBA PL011 UART driver <6>[ 0.287253] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.294903] SoC family: QorIQ LS1028A <6>[ 0.298855] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.311441] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.318484] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.325513] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.332544] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.340326] cryptd: max_cpu_qlen set to 1000 <6>[ 0.346321] ACPI: Interpreter disabled. <6>[ 0.351420] iommu: Default domain type: Translated <6>[ 0.356751] vgaarb: loaded <5>[ 0.359885] SCSI subsystem initialized <7>[ 0.364090] libata version 3.00 loaded. <6>[ 0.368346] usbcore: registered new interface driver usbfs <6>[ 0.374173] usbcore: registered new interface driver hub <6>[ 0.379818] usbcore: registered new device driver usb <6>[ 0.385441] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.393385] i2c i2c-0: IMX I2C adapter registered <6>[ 0.398553] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.406230] i2c i2c-1: IMX I2C adapter registered <6>[ 0.411327] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.419102] i2c i2c-2: IMX I2C adapter registered <6>[ 0.424388] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.429663] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.439163] PTP clock support registered <6>[ 0.443454] EDAC MC: Ver: 3.0.0 <6>[ 0.447593] FPGA manager framework <6>[ 0.451332] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.458152] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.464668] VFS: Disk quotas dquot_6.6.0 <6>[ 0.468916] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.476218] pnp: PnP ACPI: disabled <6>[ 0.483214] NET: Registered protocol family 2 <6>[ 0.488172] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.497230] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.506156] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.514495] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.522510] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.529461] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.536518] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.544090] NET: Registered protocol family 1 <6>[ 0.549051] RPC: Registered named UNIX socket transport module. <6>[ 0.555296] RPC: Registered udp transport module. <6>[ 0.560306] RPC: Registered tcp transport module. <6>[ 0.565315] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.572083] PCI: CLS 0 bytes, default 64 <6>[ 0.576396] Unpacking initramfs... <6>[ 1.207070] Freeing initrd memory: 18480K <6>[ 1.211696] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.220400] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.225620] kvm [1]: GICv3: no GICV resource entry <6>[ 1.230728] kvm [1]: disabling GICv2 emulation <6>[ 1.235494] kvm [1]: GIC system register CPU interface enabled <6>[ 1.241674] kvm [1]: vgic interrupt IRQ9 <6>[ 1.245958] kvm [1]: Hyp mode initialized successfully <5>[ 1.252378] Initialise system trusted keyrings <6>[ 1.257232] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.267137] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.273741] NFS: Registering the id_resolver key type <5>[ 1.279124] Key type id_resolver registered <5>[ 1.283609] Key type id_legacy registered <6>[ 1.287965] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.294999] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.302824] 9p: Installing v9fs 9p2000 file system support <5>[ 1.336984] Key type asymmetric registered <5>[ 1.341389] Asymmetric key parser 'x509' registered <6>[ 1.346594] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.354330] io scheduler mq-deadline registered <6>[ 1.359169] io scheduler kyber registered <6>[ 1.368531] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.376654] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 1.385805] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 1.394952] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 1.404098] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 1.413245] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 1.422395] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 1.431536] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 1.440722] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.449837] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.457133] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.462672] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 1.473388] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 1.484547] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.495263] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.506417] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.517132] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.528287] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 1.539017] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.545377] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.556187] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.567432] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.578500] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.590020] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.595828] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.606109] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.616979] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.623331] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.634136] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.645379] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.656446] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.667969] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.673776] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.684054] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.694887] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.701242] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.712047] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.723302] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.729221] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.735575] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.746380] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.757634] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.763542] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.769893] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.780700] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.791957] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.797865] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.804215] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.815020] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.826263] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.837078] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.842989] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.849340] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.860148] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.871402] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.878015] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.884381] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.892340] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <3>[ 1.900354] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-22 <6>[ 1.907700] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.915369] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.924255] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.933224] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 1.940259] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 1.946061] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 1.952564] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.963483] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.969865] pci 0001:00:00.0: supports D1 D2 <6>[ 1.974438] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.982264] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.989219] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 1.994637] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.002302] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.011183] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.020137] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 2.027170] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 2.032972] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 2.042287] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.053192] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.059572] pci 0002:00:00.0: supports D1 D2 <6>[ 2.064144] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.071945] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.078894] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 2.084893] EINJ: ACPI disabled. <6>[ 2.096243] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.104197] printk: console [ttyS0] disabled <6>[ 2.108819] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.118030] printk: console [ttyS0] enabled <6>[ 2.118030] printk: console [ttyS0] enabled <6>[ 2.126969] printk: bootconsole [ns16550a0] disabled <6>[ 2.126969] printk: bootconsole [ns16550a0] disabled <6>[ 2.137802] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.147177] SuperH (H)SCI(F) driver initialized <6>[ 2.152288] msm_serial: driver initialized <6>[ 2.157012] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 2.167570] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 2.174305] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 2.179202] arm-smmu 5000000.iommu: stage 1 translation <5>[ 2.184794] arm-smmu 5000000.iommu: stage 2 translation <5>[ 2.190384] arm-smmu 5000000.iommu: nested translation <5>[ 2.195890] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 2.203317] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 2.210137] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 2.216864] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 2.223590] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 2.233605] loop: module loaded <6>[ 2.242226] megasas: 07.714.04.00-rc1 <6>[ 2.248250] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 2.263236] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 2.276136] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 2.283223] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 2.288734] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 2.298511] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 2.306489] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 2.314483] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 2.322483] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 2.330484] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 2.338481] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 2.346479] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 2.356202] tun: Universal TUN/TAP device driver, 1.6 <6>[ 2.361999] thunder_xcv, ver 1.0 <6>[ 2.365524] thunder_bgx, ver 1.0 <6>[ 2.369049] nicpf, ver 1.0 <6>[ 2.372538] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 2.486169] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 2.492682] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using e6:ec:dc:b8:be:93 <6>[ 2.501509] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using c2:cb:23:22:6f:cf <6>[ 2.520879] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 2.634165] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.641558] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.647932] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 2.758166] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.764981] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.771343] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 2.882165] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.888969] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.895391] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 3.006179] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 3.013354] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 3.019639] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 3.026556] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 3.035561] pps pps0: new PPS source ptp0 <6>[ 3.040309] hclge is initializing <6>[ 3.043912] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 3.051426] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 3.057046] e1000: Intel(R) PRO/1000 Network Driver <6>[ 3.062202] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 3.068259] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.073502] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.079728] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.085408] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.091283] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 3.097834] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 3.104235] sky2: driver version 1.30 <6>[ 3.108817] VFIO - User Level meta-driver version: 0.3 <6>[ 3.114565] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 3.120459] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 3.127100] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.133934] ehci-pci: EHCI PCI platform driver <6>[ 3.138684] ehci-platform: EHCI generic platform driver <6>[ 3.144269] ehci-orion: EHCI orion driver <6>[ 3.148610] ehci-exynos: EHCI Exynos driver <6>[ 3.153119] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.159591] ohci-pci: OHCI PCI platform driver <6>[ 3.164332] ohci-platform: OHCI generic platform driver <6>[ 3.169903] ohci-exynos: OHCI Exynos driver <6>[ 3.174594] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.180376] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 3.188468] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.198188] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 3.204484] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.210255] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 3.218206] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.225328] hub 1-0:1.0: USB hub found <6>[ 3.229367] hub 1-0:1.0: 1 port detected <6>[ 3.233731] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.242363] hub 2-0:1.0: USB hub found <6>[ 3.246400] hub 2-0:1.0: 1 port detected <6>[ 3.250795] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.256577] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 3.264661] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.274380] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 3.280672] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.286444] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 3.294398] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.301464] hub 3-0:1.0: USB hub found <6>[ 3.305505] hub 3-0:1.0: 1 port detected <6>[ 3.309859] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.318465] hub 4-0:1.0: USB hub found <6>[ 3.322502] hub 4-0:1.0: 1 port detected <6>[ 3.327125] usbcore: registered new interface driver usb-storage <6>[ 3.335069] i2c /dev entries driver <6>[ 3.341697] sp805-wdt c000000.watchdog: registration successful <6>[ 3.348006] sp805-wdt c010000.watchdog: registration successful <6>[ 3.355438] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 3.364200] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.370689] sdhci: Copyright(c) Pierre Ossman <6>[ 3.375649] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.382531] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.388977] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 3.389569] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 3.400886] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.408169] usbcore: registered new interface driver usbhid <6>[ 3.414032] usbhid: USB HID core driver <6>[ 3.418188] mmc0: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 3.420918] NET: Registered protocol family 17 <6>[ 3.426532] mmc1: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 3.430204] 9pnet: Installing 9P2000 support <5>[ 3.441854] Key type dns_resolver registered <6>[ 3.446658] printk: console [ttyS0]: printing thread started <6>[ 3.446695] registered taskstats version 1 <5>[ 3.446700] Loading compiled-in X.509 certificates <6>[ 3.449068] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 3.450121] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 3.450350] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 3.450488] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 3.450625] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 3.493669] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 3.555555] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 3.558728] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 3.576495] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 3.598575] mmc1: new HS400 MMC card at address 0001 <6>[ 3.599008] mmcblk1: mmc1:0001 S0J56X 7.34 GiB <6>[ 3.599198] mmcblk1boot0: mmc1:0001 S0J56X partition 1 31.5 MiB <6>[ 3.599417] mmcblk1boot1: mmc1:0001 S0J56X partition 2 31.5 MiB <6>[ 3.599528] mmcblk1rpmb: mmc1:0001 S0J56X partition 3 4.00 MiB, chardev (234:0) <6>[ 3.610811] mmcblk1: p1 p2 <6>[ 3.781574] hub 3-1:1.0: USB hub found <6>[ 3.781688] hub 3-1:1.0: 7 ports detected <6>[ 6.635135] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 6.666201] Sending DHCP requests ., OK <6>[ 6.682250] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.64 <6>[ 6.682275] IP-Config: Complete: <6>[ 6.682280] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.64, mask=255.255.255.0, gw=172.16.0.254 <6>[ 6.682304] host=172.16.0.64, domain=lava.lan, nis-domain=(none) <6>[ 6.682315] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 6.682327] nameserver0=8.8.8.8 <6>[ 6.682763] clk: Disabling unused clocks <6>[ 6.682849] ALSA device list: Starting syslogd<6>[ 6.682862] No soundcards found. : <6>[ 6.688276] Freeing unused kernel memory: 6016K <6>[ 6.714377] Run /init as init process OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.769289] udevd[127]: starting version 3.2.9 <5>[ 6.769649] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.769739] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.769766] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.776576] udevd[127]: specified user 'tss' unknown <27>[ 6.776621] udevd[127]: specified group 'tss' unknown <30>[ 6.782286] udevd[128]: starting eudev-3.2.9 <27>[ 6.999379] udevd[142]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <28>[ 6.999409] udevd[142]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 7.025255] mali-dp f080000.display: Adding to iommu group 13 <6>[ 7.050038] NET: Registered protocol family 10 <6>[ 7.098614] Segment Routing with IPv6 <4>[ 7.099537] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 7.119243] mscc_felix 0000:00:00.5: Adding to iommu group 14 <6>[ 7.119378] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 7.155029] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 7.155037] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 7.155878] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.155973] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 7.156906] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 7.156991] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 7.158408] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 7.158508] rtc-rv8803 0-0032: registered as rtc0 <6>[ 7.158562] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.160246] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 7.160253] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <4>[ 7.175058] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 7.175147] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 7.175169] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 7.175189] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 7.175215] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 7.200945] wm8904 2-001a: revision A <6>[ 7.237491] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 7.436329] caam 8000000.crypto: Entropy delay = 3200 <6>[ 7.462365] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 7.476486] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 7.476500] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 7.476506] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 7.503582] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 7.504497] caam algorithms registered in /proc/crypto <6>[ 7.505399] caam 8000000.crypto: registering rng-caam <6>[ 7.505623] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 7.505982] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 7.506369] caam_jr 8040000.jr: Adding to iommu group 18 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL <5>[ 7.565707] random: crng init done <5>[ 7.565713] random: 3 urandom warning(s) missed due to ratelimiting Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-469666/environment . /lava-469666/environment / # /lava-469666/bin/lava-test-runner /lava-469666/0 /lava-469666/bin/lava-test-runner /lava-469666/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-469666/0<8>[ 8.128117] /tests/0_dmesg + cat uuid + UUID=469666_1.5.2.4.1 + set +x + KERNELCI_LAVA=y<8>[ 8.141667] /bin/sh /opt/kernelci/dmesg.sh<8>[ 8.153291] + set +x <8>[ 8.165053] [ 8.165588] R EXIT> / #