Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.107 (255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 503384/tftp-deploy-8mzr4__4/kernel/Image tftp 0x82000000 503384/tftp-deploy-8mzr4__4/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.107; sending through gateway 172.16.0.254 Filename '503384/tftp-deploy-8mzr4__4/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 14.9 MiB/s done Bytes transferred = 37902848 (2425a00 hex) => tftp 0x90080000 503384/tftp-deploy-8mzr4__4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 503384/tftp-deploy-8mzr4__4/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.107; sending through gateway 172.16.0.254 Filename '503384/tftp-deploy-8mzr4__4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################## 14 MiB/s done Bytes transferred = 22209747 (152e4d3 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 503384/tftp-deploy-8mzr4__4/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 503384/tftp-deploy-8mzr4__4/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.107; sending through gateway 172.16.0.254 Filename '503384/tftp-deploy-8mzr4__4/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 6.9 MiB/s done Bytes transferred = 28772 (7064 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-10-10 10:03:32 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 22209683 Bytes = 21.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a063 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.111-cip29-rt15 (KernelCI@build-j339961-arm64-gcc-12-defconfig-lf8cz) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Thu Oct 10 09:48:29 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7f6a00-0x20ff7f8fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 21 pages/cpu s47848 r8192 d29976 u86016 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3888124K/4126720K available (16192K kernel code, 3734K rwdata, 9360K rodata, 7616K init, 609K bss, 205828K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008843] Console: colour dummy device 80x25 <6>[ 0.013634] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024354] pid_max: default: 32768 minimum: 301 <6>[ 0.029309] LSM: Security Framework initializing <6>[ 0.034302] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.042049] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051088] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.058661] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.065117] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.072679] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.079238] rcu: Hierarchical SRCU implementation. <6>[ 0.079240] rcu: Max phase no-delay instances is 1000. <6>[ 0.079279] printk: bootconsole [ns16550a0] printing thread started <6>[ 0.096597] Platform MSI: gic-its@6020000 domain created <6>[ 0.096675] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.096718] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.097487] EFI services will not be available. <6>[ 0.097580] smp: Bringing up secondary CPUs ... <6>[ 0.097857] Detected PIPT I-cache on CPU1 <6>[ 0.097906] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.097915] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.097940] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.152297] smp: Brought up 1 node, 2 CPUs <6>[ 0.152301] SMP: Total of 2 processors activated. <6>[ 0.152304] CPU features: detected: 32-bit EL0 Support <6>[ 0.152305] CPU features: detected: 32-bit EL1 Support <6>[ 0.152308] CPU features: detected: CRC32 instructions <6>[ 0.152346] CPU: All CPU(s) started at EL2 <6>[ 0.152358] alternatives: applying system-wide alternatives <6>[ 0.153435] devtmpfs: initialized <6>[ 0.156794] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.156805] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.157406] pinctrl core: initialized pinctrl subsystem <6>[ 0.157808] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.157810] SoC family: QorIQ LS1028A <6>[ 0.157812] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.158157] DMI not present or invalid. <6>[ 0.158564] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.159143] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.159256] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.159407] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.159438] audit: initializing netlink subsys (disabled) <6>[ 0.160059] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.160062] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.160100] cpuidle: using governor menu <6>[ 0.160216] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <5>[ 0.160229] audit: type=2000 audit(0.124:1): state=initialized audit_enabled=0 res=1 <6>[ 0.160253] ASID allocator initialised with 65536 entries <6>[ 0.161122] Serial: AMBA PL011 UART driver <4>[ 0.171432] KASLR disabled due to lack of seed <6>[ 0.176325] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.176328] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.176332] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.176334] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.176337] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.176339] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.176341] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.176343] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.178632] ACPI: Interpreter disabled. <6>[ 0.179986] iommu: Default domain type: Translated <6>[ 0.179989] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.180129] SCSI subsystem initialized <6>[ 0.180322] usbcore: registered new interface driver usbfs <6>[ 0.180341] usbcore: registered new interface driver hub <6>[ 0.180359] usbcore: registered new device driver usb <6>[ 0.180648] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.180896] i2c i2c-0: IMX I2C adapter registered <6>[ 0.181023] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.181112] i2c i2c-1: IMX I2C adapter registered <6>[ 0.181198] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.181351] i2c i2c-2: IMX I2C adapter registered <6>[ 0.181743] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.181746] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.181753] PTP clock support registered <6>[ 0.181988] EDAC MC: Ver: 3.0.0 <6>[ 0.182854] FPGA manager framework <6>[ 0.182899] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.183319] vgaarb: loaded <6>[ 0.183506] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.183626] VFS: Disk quotas dquot_6.6.0 <6>[ 0.183648] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.183742] pnp: PnP ACPI: disabled <6>[ 0.187147] NET: Registered PF_INET protocol family <6>[ 0.187450] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.189532] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.189563] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.189572] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.189654] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.190309] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.190397] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.190423] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.190543] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.190856] RPC: Registered named UNIX socket transport module. <6>[ 0.190860] RPC: Registered udp transport module. <6>[ 0.190861] RPC: Registered tcp transport module. <6>[ 0.190863] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.190869] PCI: CLS 0 bytes, default 64 <6>[ 0.191133] Unpacking initramfs... <6>[ 0.195553] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 0.195811] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.196725] kvm [1]: GICv3: no GICV resource entry <6>[ 0.196729] kvm [1]: disabling GICv2 emulation <6>[ 0.196744] kvm [1]: GIC system register CPU interface enabled <6>[ 0.196784] kvm [1]: vgic interrupt IRQ9 <6>[ 0.196821] kvm [1]: Hyp mode initialized successfully <5>[ 0.197435] Initialise system trusted keyrings <6>[ 0.203560] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.207179] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.211793] NFS: Registering the id_resolver key type <5>[ 0.211814] Key type id_resolver registered <5>[ 0.211816] Key type id_legacy registered <6>[ 0.211858] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.211861] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.211966] 9p: Installing v9fs 9p2000 file system support <5>[ 0.264892] Key type asymmetric registered <5>[ 0.264898] Asymmetric key parser 'x509' registered <6>[ 0.264954] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.264958] io scheduler mq-deadline registered <6>[ 0.264961] io scheduler kyber registered <6>[ 0.282066] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.282092] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.282107] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.282120] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.282133] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.282145] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.282157] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.282168] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.282218] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.282282] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.282287] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.282291] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.282294] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.282299] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.282302] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.282305] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.282308] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.282311] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.282330] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 0.282364] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.282370] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.282377] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.282383] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.282401] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.282411] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 0.282416] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 0.282554] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 0.282579] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.282585] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.282591] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.282596] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.282614] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 0.282623] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 0.282627] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 0.282775] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 0.282803] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.282810] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.282826] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 0.282956] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 0.282984] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.282991] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.283007] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 0.283111] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 0.283135] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.283141] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.283158] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 0.283288] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 0.283312] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.283318] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.283323] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.283339] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 0.283475] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 0.283499] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.283648] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.283666] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 0.284495] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 0.284537] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 0.284682] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 0.284789] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 0.291586] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 0.292238] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 0.292261] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 0.292273] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 0.292320] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 0.292323] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 0.965228] Freeing initrd memory: 21684K <3>[ 1.287517] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 1.287634] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 1.287640] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 1.287646] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 1.287651] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.287678] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.287745] pci 0001:00:00.0: supports D1 D2 <6>[ 1.287749] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.288692] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.288706] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 1.288843] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 1.288865] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 1.288877] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 1.288925] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 1.288928] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 2.289032] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 2.289090] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 2.289094] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 2.289100] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 2.289105] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.289124] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.337317] printk: c[ 2.337324] printk: console [ttyS0] enabled >[ 2.289180<6>[ 2.337327] printk: bootconsole [ns16550a0] disabled ] pci 0002:00:00.0: supports D1 D2 <6>[ 2.357425] printk: bootconsole [ns16550a0] printing thread stopped <6>[ 2.357801] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 2.358166] SuperH (H)SCI(F) driver initialized <6>[ 2.358469] msm_serial: driver initialized <6>[ 2.358871] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 2.361003] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 2.361008] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 2.361012] arm-smmu 5000000.iommu: stage 1 translation <5>[ 2.361014] arm-smmu 5000000.iommu: stage 2 translation <5>[ 2.361016] arm-smmu 5000000.iommu: nested translation <5>[ 2.361020] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 2.361024] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 2.361030] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 2.361033] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 2.361036] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 2.361254] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 2.368752] loop: module loaded <4>[ 2.374242] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 2.375194] megasas: 07.719.03.00-rc1 <6>[ 2.377317] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 2.391194] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 2.403334] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 2.403344] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 2.403348] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 2.404029] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 2.404561] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 2.405075] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 2.405592] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 2.408303] tun: Universal TUN/TAP device driver, 1.6 <6>[ 2.408867] thunder_xcv, ver 1.0 <6>[ 2.408888] thunder_bgx, ver 1.0 <6>[ 2.408910] nicpf, ver 1.0 <6>[ 2.409462] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 2.409680] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 2.515514] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.516422] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.516503] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 2.623517] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.623849] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.623922] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 2.731516] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.731854] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.732187] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 2.839517] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 2.854377] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 2.854475] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 2.854596] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 2.854699] pps pps0: new PPS source ptp0 <6>[ 2.855180] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 2.855184] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 2.855222] hclge is initializing <6>[ 2.855233] e1000: Intel(R) PRO/1000 Network Driver <6>[ 2.855235] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 2.855260] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.855261] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.855288] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.855290] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.855312] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.855314] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.855590] sky2: driver version 1.30 <6>[ 2.856327] VFIO - User Level meta-driver version: 0.3 <6>[ 2.856687] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 2.857128] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 2.859410] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 2.859422] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 2.859997] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 2.860025] xhci-hcd xhci-hcd.0.auto: irq 100, io mem 0x03110000 <6>[ 2.860111] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 2.860117] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 2.860123] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 2.860438] hub 1-0:1.0: USB hub found <6>[ 2.860452] hub 1-0:1.0: 1 port detected <6>[ 2.860610] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 2.860837] hub 2-0:1.0: USB hub found <6>[ 2.860852] hub 2-0:1.0: 1 port detected <6>[ 2.861363] usbcore: registered new interface driver usb-storage <6>[ 2.862742] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 2.862753] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 2.862875] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 2.862889] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03100000 <6>[ 2.862990] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 2.862996] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 2.863002] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 2.863344] hub 3-0:1.0: USB hub found <6>[ 2.863360] hub 3-0:1.0: 1 port detected <6>[ 2.863553] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 2.863800] hub 4-0:1.0: USB hub found <6>[ 2.863815] hub 4-0:1.0: 1 port detected <6>[ 2.877903] i2c_dev: i2c /dev entries driver <6>[ 2.881280] sp805-wdt c000000.watchdog: registration successful <6>[ 2.881410] sp805-wdt c010000.watchdog: registration successful <6>[ 2.895171] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 2.895927] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.895931] sdhci: Copyright(c) Pierre Ossman <6>[ 2.896420] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.897077] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.897657] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 2.897938] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 2.903629] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.910984] usbcore: registered new interface driver usbhid <6>[ 2.910989] usbhid: USB HID core driver <6>[ 2.915151] NET: Registered PF_PACKET protocol family <6>[ 2.915234] 9pnet: Installing 9P2000 support <5>[ 2.915281] Key type dns_resolver registered <6>[ 2.915657] registered taskstats version 1 <5>[ 2.915672] Loading compiled-in X.509 certificates <6>[ 2.924471] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 2.925519] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 2.925673] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 2.925868] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 2.926012] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 2.926155] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 2.926299] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 2.927540] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 2.927579] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 3.016104] mmc0: new HS400 MMC card at address 0001 <6>[ 3.016457] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 3.017595] mmcblk0: p1 p2 <6>[ 3.018011] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 3.018965] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 3.019813] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 3.031523] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 3.032469] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 1e:c8:5e:0c:9e:76 <6>[ 3.032478] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using f6:d6:71:46:ec:cb <6>[ 3.035781] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 3.097056] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 3.107695] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 3.115543] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 3.308246] hub 1-1:1.0: USB hub found <6>[ 3.308284] hub 1-1:1.0: 7 ports detected <6>[ 6.176520] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 6.199558] Sending DHCP requests ., OK <6>[ 6.215583] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.107 <6>[ 6.215609] IP-Config: Complete: <6>[ 6.215614] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.107, mask=255.255.255.0, gw=172.16.0.254 Starting syslogd<6>[ 6.215636] host=172.16.0.107, domain=lava.lan, nis-domain=(none) : <6>[ 6.215646] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 6.215659] nameserver0=8.8.8.8 <6>[ 6.216124] clk: Disabling unused clocks OK<6>[ 6.216214] ALSA device list: <6>[ 6.216228] No soundcards found. Starting klogd: <6>[ 6.221348] Freeing unused kernel memory: 7616K OK<6>[ 6.221417] Run /init as init process Running sysctl: OK Populating /dev using udev: <30>[ 6.298856] udevd[133]: starting version 3.2.9 <5>[ 7.303511] random: crng init done <27>[ 7.306327] udevd[133]: specified user 'tss' unknown <27>[ 7.306372] udevd[133]: specified group 'tss' unknown <30>[ 7.307258] udevd[134]: starting eudev-3.2.9 <6>[ 7.535323] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 7.535392] fsl_ddr_edac acquired irq 111 for MC <6>[ 7.535396] fsl_ddr_edac MC err registered <27>[ 7.552663] udevd[142]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <28>[ 7.552691] udevd[142]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 7.568223] NET: Registered PF_INET6 protocol family <4>[ 7.589206] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 7.590116] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 7.590218] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 7.591151] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 7.602886] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <4>[ 7.610624] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 7.623979] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 7.683643] Segment Routing with IPv6 <6>[ 7.683657] In-situ OAM (IOAM) with IPv6 <4>[ 7.698647] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <4>[ 7.709397] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 7.709405] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 7.712321] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 7.712448] rtc-rv8803 0-0032: registered as rtc0 <6>[ 7.719685] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 7.729138] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 7.729145] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 7.730133] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <4>[ 7.741422] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 7.741690] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 7.741714] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 7.741740] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 7.741874] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 7.754921] wm8904 2-001a: revision A <6>[ 7.782549] CAN device driver interface <6>[ 7.793604] mscc_felix 0000:00:00.5: Adding to iommu group 13 <6>[ 7.793746] mscc_felix 0000:00:00.5: device is disabled, skipping <6>[ 7.825213] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 7.850795] caam 8000000.crypto: Entropy delay = 3200 <6>[ 7.871481] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 7.890954] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 7.890969] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 7.890974] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 7.928579] mali-dp f080000.display: Adding to iommu group 14 <6>[ 7.947885] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.947930] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 7.948218] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 8.027877] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 8.031144] caam algorithms registered in /proc/crypto <6>[ 8.036532] caam 8000000.crypto: registering rng-caam <6>[ 8.037296] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 8.037690] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 8.038537] caam_jr 8030000.jr: Adding to iommu group 17 done <6>[ 8.039288] caam_jr 8040000.jr: Adding to iommu group 18 Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-503384/environment . /lava-503384/environment / # /lava-503384/bin/lava-test-runner /lava-503384/0 /lava-503384/bin/lava-test-runner /lava-503384/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 8.655129] d /lava-503384/0/tests/0_dmesg + cat uuid + UUID=503384_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.672756] <8>[ 8.693570] <8>[ 8.714361] + set +x <8>[ 8.723362] / #