[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.13 (9 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10597212/tftp-deploy-kc8lm8pp/kernel/zImage tftp 0x10000000 10597212/tftp-deploy-kc8lm8pp/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10597212/tftp-deploy-kc8lm8pp/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 2.8 MiB/s done Bytes transferred = 10347008 (9de200 hex) => tftp 0x14000000 10597212/tftp-deploy-kc8lm8pp/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10597212/tftp-deploy-kc8lm8pp/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10597212/tftp-deploy-kc8lm8pp/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 2.9 MiB/s done Bytes transferred = 17159547 (105d57b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10597212/tftp-deploy-kc8lm8pp/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10597212/tftp-deploy-kc8lm8pp/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10597212/tftp-deploy-kc8lm8pp/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.4 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9de200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17159483 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.31 (KernelCI@build-j1612325-arm-gcc-10-multi-v7-defconfig-cnjxw) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Jun 5 22:04:32 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 930392K/1048576K available (14336K kernel code, 2468K rwdata, 6008K rodata, 2048K init, 429K bss, 52648K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000000] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008088] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021944] Console: colour dummy device 80x30 <6>[ 0.023849] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034514] pid_max: default: 32768 minimum: 301 <6>[ 0.039564] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046967] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055568] CPU: Testing write buffer coherency: ok <6>[ 0.060096] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065710] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072190] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079748] rcu: Hierarchical SRCU implementation. <6>[ 0.083133] rcu: Max phase no-delay instances is 1000. <6>[ 0.092192] EFI services will not be available. <6>[ 0.094499] smp: Bringing up secondary CPUs ... <6>[ 0.099753] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099768] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.111070] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.111084] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.122279] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.122296] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.132691] smp: Brought up 1 node, 4 CPUs <6>[ 0.136955] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.143459] CPU: All CPU(s) started in SVC mode. <6>[ 0.148935] devtmpfs: initialized <6>[ 0.159648] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.164943] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.174872] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.185382] pinctrl core: initialized pinctrl subsystem <6>[ 0.191744] DMI not present or invalid. <6>[ 0.193800] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.202728] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.209662] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.209729] cpuidle: using governor menu <6>[ 0.217712] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.231314] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.236341] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.266036] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2100000/i2c@21a4000/camera@40 <6>[ 0.282746] platform 2400000.ipu: Fixed dependency cycle(s) with /disp0 <6>[ 0.287298] platform disp0: Fixed dependency cycle(s) with /panel-lcd <6>[ 0.293963] platform ldb: Fixed dependency cycle(s) with /panel-lvds0 <6>[ 0.301644] No ATAGs? <6>[ 0.302849] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.310990] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.320358] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.331936] Serial: AMBA PL011 UART driver <6>[ 0.336292] printk: console [ramoops-1] enabled <6>[ 0.338459] pstore: Registered ramoops as persistent store backend <6>[ 0.344669] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.382507] iommu: Default domain type: Translated <6>[ 0.384808] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.392173] SCSI subsystem initialized <6>[ 0.395932] usbcore: registered new interface driver usbfs <6>[ 0.401115] usbcore: registered new interface driver hub <6>[ 0.406712] usbcore: registered new device driver usb <4>[ 0.412184] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.420018] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.428467] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.436382] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.446652] i2c i2c-0: IMX I2C adapter registered <6>[ 0.450984] i2c i2c-1: IMX I2C adapter registered <6>[ 0.455470] i2c i2c-2: IMX I2C adapter registered <6>[ 0.460996] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.464758] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.474189] PTP clock support registered <6>[ 0.478597] EDAC MC: Ver: 3.0.0 <6>[ 0.485576] vgaarb: loaded <6>[ 1.591333] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.604737] NET: Registered PF_INET protocol family <6>[ 1.607600] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.616859] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 1.623405] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.631426] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.639415] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 1.647159] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.653696] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.660330] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.667878] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.674195] RPC: Registered named UNIX socket transport module. <6>[ 1.679689] RPC: Registered udp transport module. <6>[ 1.684679] RPC: Registered tcp transport module. <6>[ 1.689605] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.696329] PCI: CLS 0 bytes, default 64 <6>[ 1.701020] Trying to unpack rootfs image as initramfs... <4>[ 1.701159] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 1.714779] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.724448] Initialise system trusted keyrings <6>[ 1.727436] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.739784] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.743967] NFS: Registering the id_resolver key type <5>[ 1.748389] Key type id_resolver registered <5>[ 1.752833] Key type id_legacy registered <6>[ 1.757206] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.764043] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.771742] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.776924] Key type asymmetric registered <5>[ 1.780630] Asymmetric key parser 'x509' registered <6>[ 1.786045] bounce: pool size: 64 pages <6>[ 1.789989] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.797545] io scheduler mq-deadline registered <6>[ 1.802304] io scheduler kyber registered <6>[ 1.857771] mxs-dma 110000.dma-apbh: initialized <6>[ 1.936409] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.945525] SuperH (H)SCI(F) driver initialized <6>[ 1.948619] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 269, base_baud = 5000000) is a IMX <6>[ 1.957583] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 270, base_baud = 5000000) is a IMX <6>[ 1.965499] printk: console [ttymxc1] enabled <6>[ 1.965499] printk: console [ttymxc1] enabled <6>[ 1.974648] printk: bootconsole [ec_imx21] disabled <6>[ 1.974648] printk: bootconsole [ec_imx21] disabled <6>[ 1.986531] msm_serial: driver initialized <6>[ 1.992189] STMicroelectronics ASC driver initialized <6>[ 1.999464] STM32 USART driver initialized <6>[ 2.026439] brd: module loaded <6>[ 2.037325] loop: module loaded <6>[ 2.044912] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.053164] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.061471] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.069925] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 2.077981] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 2.085799] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 2.093460] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 2.104261] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.111599] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.120673] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.131926] scsi host0: ahci-imx <6>[ 2.135840] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 <6>[ 2.157985] CAN device driver interface <6>[ 2.164071] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.174115] pps pps0: new PPS source ptp0 <3>[ 2.180940] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address <6>[ 2.188422] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 <6>[ 2.195784] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 <6>[ 2.203129] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 <6>[ 2.210450] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 <6>[ 2.217795] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 <6>[ 2.225140] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 <6>[ 2.232477] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 <6>[ 2.473048] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.478801] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.485415] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.164661] Freeing initrd memory: 16760K <4>[ 3.169278] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.180017] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.207947] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.215602] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.220842] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.227124] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.232810] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.245504] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 3.251413] usbcore: registered new interface driver pegasus <6>[ 3.257395] usbcore: registered new interface driver asix <6>[ 3.263117] usbcore: registered new interface driver ax88179_178a <6>[ 3.269514] usbcore: registered new interface driver cdc_ether <6>[ 3.275675] usbcore: registered new interface driver smsc75xx <6>[ 3.281761] usbcore: registered new interface driver smsc95xx <6>[ 3.287815] usbcore: registered new interface driver net1080 <6>[ 3.293805] usbcore: registered new interface driver cdc_subset <6>[ 3.300028] usbcore: registered new interface driver zaurus <6>[ 3.305955] usbcore: registered new interface driver cdc_ncm <6>[ 3.318792] usbcore: registered new interface driver usb-storage <6>[ 3.333959] i2c_dev: i2c /dev entries driver <6>[ 3.362861] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.369322] sdhci: Copyright(c) Pierre Ossman <6>[ 3.376996] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.385962] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.393358] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.393567] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.398640] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.409496] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.417900] usbcore: registered new interface driver usbhid <6>[ 3.423786] usbhid: USB HID core driver <6>[ 3.438127] NET: Registered PF_INET6 protocol family <6>[ 3.441222] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.441282] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.444706] Segment Routing with IPv6 <6>[ 3.461722] In-situ OAM (IOAM) with IPv6 <6>[ 3.466003] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.472861] NET: Registered PF_PACKET protocol family <6>[ 3.478191] can: controller area network core <6>[ 3.482910] NET: Registered PF_CAN protocol family <6>[ 3.485550] mmc2: new high speed SDHC card at address 0001 <6>[ 3.487971] can: raw protocol <6>[ 3.494706] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 3.496981] can: broadcast manager protocol <6>[ 3.505955] can: netlink gateway - max_hops=1 <5>[ 3.511007] Key type dns_resolver registered <6>[ 3.517787] ThumbEE CPU extension supported. <5>[ 3.522375] Registering SWP/SWPB emulation handler <5>[ 3.528152] Loading compiled-in X.509 certificates <4>[ 3.528177] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 3.539151] pstore: Using crash dump compression: deflate <4>[ 3.540896] GPT:29296874 != 30965759 <4>[ 3.540906] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.556774] GPT:29296874 != 30965759 <4>[ 3.560628] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.566155] mmcblk2: p1 p2 p3 <4>[ 3.583161] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.593376] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.598556] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.631504] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.638821] hub 1-0:1.0: USB hub found <6>[ 3.643002] hub 1-0:1.0: 1 port detected <3>[ 3.652300] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 3.659895] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 3.668286] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <6>[ 3.684691] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 3.701350] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 3.931361] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.133072] hub 1-1:1.0: USB hub found <6>[ 4.137308] hub 1-1:1.0: 3 ports detected <6>[ 5.761778] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 5.769774] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.811382] Sending DHCP requests ., OK <6>[ 5.855579] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.13 <6>[ 5.863952] IP-Config: Complete: <6>[ 5.867467] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.201.13, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.878223] host=imx6q-sabrelite-lava-cbg-2, domain=lava-rack, nis-domain=(none) <6>[ 5.886346] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.886357] nameserver0=192.168.201.1 <6>[ 5.904292] Freeing unused kernel image (initmem) memory: 2048K <6>[ 5.931862] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.114585] udevd[124]: starting version 3.2.9 <5>[ 8.711326] random: crng init done <27>[ 8.724273] udevd[124]: specified user 'tss' unknown <27>[ 8.729733] udevd[124]: specified group 'tss' unknown <30>[ 8.738733] udevd[125]: starting eudev-3.2.9 <6>[ 9.224625] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 9.235103] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 9.392590] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 9.479001] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.503177] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.511781] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.518750] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 9.526011] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 9.533058] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 9.539445] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 9.583819] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 9.894535] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 9.969225] caam 2100000.crypto: Entropy delay = 3200 <6>[ 10.035420] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 10.096184] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 10.101654] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 10.108555] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 10.187948] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 10.197791] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <3>[ 10.314328] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' <6>[ 10.543554] caam algorithms registered in /proc/crypto <6>[ 10.550531] caam 2100000.crypto: registering rng-caam <6>[ 10.556546] caam 2100000.crypto: rng crypto API alg registered prng-caam done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10597212/environment . /lava-10597212/environment / # /lava-10597212/bin/lava-test-runner /lava-10597212/0 /lava-10597212/bin/lava-test-runner /lava-10597212/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-10597212/0/tests/0_dmesg + cat uuid + UUID=10597212_1.5.2<8>[ 11.340529] .4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.395425] <8>[ 11.438531] <8>[ 11.481718] + set<8>[ 11.491725] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10597212/environment / # . /lava-10597212/environment/lava-10597212/bin/lava-test-runner /lava-10597212/1 / # /lava-10597212/bin/lava-test-runner /lava-10597212/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10597212/1/tests/1_bootrr + cat uuid + UUID=10597212_1.5.2.4.5<8>[ 12.029048] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10597212/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds platform: supplier 208c000.pwm not ready panel-lcd platform: supplier backlight-lcd not ready panel-lvds0 platform: supplier backlight-lvds not ready ldb disp0 backlight-lcd platform: supplier 2080000.pwm not ready /lava-10597212/1/../bin/lava-test-case <8>[ 13.129271] /lava-10597212/1/../bin/lava-test-case <8>[ 13.193176] /lava-10597212/1/../bin/lava-test-case <8>[ 13.226965] + set<8>[ 13.247286] +x / #