[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10597217/tftp-deploy-k9ubkqxu/kernel/zImage tftp 0x10000000 10597217/tftp-deploy-k9ubkqxu/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10597217/tftp-deploy-k9ubkqxu/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.7 MiB/s done Bytes transferred = 10347008 (9de200 hex) => tftp 0x14000000 10597217/tftp-deploy-k9ubkqxu/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10597217/tftp-deploy-k9ubkqxu/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10597217/tftp-deploy-k9ubkqxu/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 11.6 MiB/s done Bytes transferred = 13233038 (c9eb8e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10597217/tftp-deploy-k9ubkqxu/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10597217/tftp-deploy-k9ubkqxu/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10597217/tftp-deploy-k9ubkqxu/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.4 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10597217/extract-nfsrootfs-hvn33nd4,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10597217/extract-nfsrootfs-hvn33nd4,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9de200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13232974 Bytes = 12.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.31 (KernelCI@build-j1612325-arm-gcc-10-multi-v7-defconfig-cnjxw) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Jun 5 22:04:32 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10597217/extract-nfsrootfs-hvn33nd4,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 934228K/1048576K available (14336K kernel code, 2468K rwdata, 6008K rodata, 2048K init, 429K bss, 48812K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000017] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004063] Console: colour dummy device 80x30 [ 0.004127] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004141] pid_max: default: 32768 minimum: 301 [ 0.004331] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004356] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004982] CPU: Testing write buffer coherency: ok [ 0.005040] CPU0: Spectre v2: using BPIALL workaround [ 0.005350] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006248] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007877] rcu: Hierarchical SRCU implementation. [ 0.007883] rcu: Max phase no-delay instances is 1000. [ 0.011545] EFI services will not be available. [ 0.011923] smp: Bringing up secondary CPUs ... [ 0.012750] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012766] CPU1: Spectre v2: using BPIALL workaround [ 0.013694] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013709] CPU2: Spectre v2: using BPIALL workaround [ 0.014612] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014626] CPU3: Spectre v2: using BPIALL workaround [ 0.014725] smp: Brought up 1 node, 4 CPUs [ 0.014736] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.014747] CPU: All CPU(s) started in SVC mode. [ 0.015315] devtmpfs: initialized [ 0.023091] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.023317] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.023341] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.026625] pinctrl core: initialized pinctrl subsystem [ 0.030373] DMI not present or invalid. [ 0.031193] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.034683] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.037316] thermal_sys: Registered thermal governor 'step_wise' [ 0.037378] cpuidle: using governor menu [ 0.037620] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.046198] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2800000 [ 0.046311] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2400000 [ 0.068453] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2100000/i2c@21a4000/camera@40 [ 0.078286] platform 2400000.ipu: Fixed dependency cycle(s) with /disp0 [ 0.078787] platform disp0: Fixed dependency cycle(s) with /panel-lcd [ 0.079314] platform ldb: Fixed dependency cycle(s) with /panel-lvds0 [ 0.080766] No ATAGs? [ 0.080921] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.080932] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.084212] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.091557] Serial: AMBA PL011 UART driver [ 0.094286] printk: console [ramoops-1] enabled [ 0.094532] pstore: Registered ramoops as persistent store backend [ 0.094547] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.134909] iommu: Default domain type: Translated [ 0.134933] iommu: DMA domain TLB invalidation policy: strict mode [ 0.135733] SCSI subsystem initialized [ 0.136263] usbcore: registered new interface driver usbfs [ 0.136318] usbcore: registered new interface driver hub [ 0.136367] usbcore: registered new device driver usb [ 0.136611] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 0.136756] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 0.136921] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 0.137059] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 0.139008] i2c i2c-0: IMX I2C adapter registered [ 0.140382] i2c i2c-1: IMX I2C adapter registered [ 0.141273] i2c i2c-2: IMX I2C adapter registered [ 0.142702] pps_core: LinuxPPS API ver. 1 registered [ 0.142717] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.142771] PTP clock support registered [ 0.143037] EDAC MC: Ver: 3.0.0 [ 0.146914] vgaarb: loaded [ 1.336501] clocksource: Switched to clocksource mxc_timer1 [ 1.347723] NET: Registered PF_INET protocol family [ 1.348243] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.350243] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.350296] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.350320] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.350425] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 1.350765] TCP: Hash tables configured (established 8192 bind 8192) [ 1.351029] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.351093] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.351353] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.352102] RPC: Registered named UNIX socket transport module. [ 1.352125] RPC: Registered udp transport module. [ 1.352136] RPC: Registered tcp transport module. [ 1.352145] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.352162] PCI: CLS 0 bytes, default 64 [ 1.352916] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 1.353071] Trying to unpack rootfs image as initramfs... [ 1.378304] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.380425] Initialise system trusted keyrings [ 1.380745] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.386731] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.387529] NFS: Registering the id_resolver key type [ 1.387593] Key type id_resolver registered [ 1.387606] Key type id_legacy registered [ 1.387705] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.387722] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.387762] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.388287] Key type asymmetric registered [ 1.388308] Asymmetric key parser 'x509' registered [ 1.388474] bounce: pool size: 64 pages [ 1.388592] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.388609] io scheduler mq-deadline registered [ 1.388622] io scheduler kyber registered [ 1.439174] mxs-dma 110000.dma-apbh: initialized [ 1.521157] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.526564] SuperH (H)SCI(F) driver initialized [ 1.527717] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 269, base_baud = 5000000) is a IMX [ 1.528747] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 270, base_baud = 5000000) is a IMX [ 2.417357] Freeing initrd memory: 12924K [ 2.422465] printk: console [ttymxc1] enabled [ 2.431399] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.441823] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware [ 2.443027] msm_serial: driver initialized [ 2.454409] STMicroelectronics ASC driver initialized [ 2.461295] STM32 USART driver initialized [ 2.487670] brd: module loaded [ 2.498158] loop: module loaded [ 2.505361] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.513343] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.521381] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.529587] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.537353] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 2.544848] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 2.552159] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 2.562573] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.569593] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.578415] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.589028] scsi host0: ahci-imx [ 2.592585] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 [ 2.613883] CAN device driver interface [ 2.619601] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.629146] pps pps0: new PPS source ptp0 [ 2.635204] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address [ 2.642390] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 [ 2.649472] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 [ 2.656543] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 [ 2.663596] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 [ 2.670666] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 [ 2.677734] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 [ 2.684785] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 [ 2.691853] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 7 [ 2.714256] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.721616] e1000e: Intel(R) PRO/1000 Network Driver [ 2.726614] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.732604] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.738038] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.750499] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 2.756132] usbcore: registered new interface driver pegasus [ 2.761867] usbcore: registered new interface driver asix [ 2.767329] usbcore: registered new interface driver ax88179_178a [ 2.773467] usbcore: registered new interface driver cdc_ether [ 2.779370] usbcore: registered new interface driver smsc75xx [ 2.785171] usbcore: registered new interface driver smsc95xx [ 2.790986] usbcore: registered new interface driver net1080 [ 2.796705] usbcore: registered new interface driver cdc_subset [ 2.802667] usbcore: registered new interface driver zaurus [ 2.808329] usbcore: registered new interface driver cdc_ncm [ 2.820949] usbcore: registered new interface driver usb-storage [ 2.835721] i2c_dev: i2c /dev entries driver [ 2.864340] sdhci: Secure Digital Host Controller Interface driver [ 2.870584] sdhci: Copyright(c) Pierre Ossman [ 2.878050] Synopsys Designware Multimedia Card Interface Driver [ 2.886736] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.897127] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 2.898477] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 2.902144] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 2.912344] ledtrig-cpu: registered to indicate activity on CPUs [ 2.920582] usbcore: registered new interface driver usbhid [ 2.926174] usbhid: USB HID core driver [ 2.927876] ata1: SATA link down (SStatus 0 SControl 300) [ 2.935464] ahci-imx 2200000.sata: no device found, disabling link. [ 2.940269] NET: Registered PF_INET6 protocol family [ 2.941789] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 2.948174] Segment Routing with IPv6 [ 2.949975] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 2.964528] In-situ OAM (IOAM) with IPv6 [ 2.968575] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.975141] NET: Registered PF_PACKET protocol family [ 2.978868] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 2.980230] can: controller area network core [ 2.991558] NET: Registered PF_CAN protocol family [ 2.996387] can: raw protocol [ 2.999369] can: broadcast manager protocol [ 3.003567] can: netlink gateway - max_hops=1 [ 3.008307] Key type dns_resolver registered [ 3.014761] ThumbEE CPU extension supported. [ 3.019093] Registering SWP/SWPB emulation handler [ 3.025298] Loading compiled-in X.509 certificates [ 3.036196] pstore: Using crash dump compression: deflate [ 3.072931] imx_usb 2184200.usb: No over current polarity defined [ 3.078158] mmc2: new high speed SDHC card at address aaaa [ 3.082895] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.085546] mmcblk2: mmc2:aaaa SL16G 14.8 GiB [ 3.089461] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.108288] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.115703] GPT:7812499 != 31116287 [ 3.119235] GPT:Alternate GPT header not at the end of the disk. [ 3.125250] GPT:7812499 != 31116287 [ 3.126345] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.128766] GPT: Use GNU Parted to correct GPT errors. [ 3.139370] mmcblk2: p1 p2 p3 [ 3.139787] hub 1-0:1.0: USB hub found [ 3.146343] hub 1-0:1.0: 1 port detected [ 3.152835] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 3.170938] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.189239] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.436374] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.638001] hub 1-1:1.0: USB hub found [ 3.641971] hub 1-1:1.0: 3 ports detected [ 6.326798] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.334354] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.376368] Sending DHCP requests ., OK [ 6.420306] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 [ 6.428414] IP-Config: Complete: [ 6.431663] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 [ 6.442175] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) [ 6.450058] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.450079] nameserver0=192.168.201.1 [ 6.470364] Freeing unused kernel image (initmem) memory: 2048K [ 6.506827] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 [ 7.468805] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.482236] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.536547] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) [ 7.559755] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.580155] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.596402] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.603084] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.645065] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.686421] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.692554] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.698692] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.705478] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.726225] caam 2100000.crypto: Entropy delay = 3200 [ 7.792155] caam 2100000.crypto: Instantiated RNG4 SH0 [ 7.802199] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.842677] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.852917] caam 2100000.crypto: Instantiated RNG4 SH1 [ 7.858099] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 7.864734] caam 2100000.crypto: job rings = 2, qi = 0 [ 7.956555] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' [ 8.217296] caam algorithms registered in /proc/crypto [ 8.223903] caam 2100000.crypto: registering rng-caam [ 8.229352] caam 2100000.crypto: rng crypto API alg registered prng-caam Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: 192.[ 8.411450] random: crng init done 168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.705585] systemd[1]: System time before build time, advancing clock. [ 9.767803] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 9.791599] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 9.839028] systemd[1]: Set hostname to . [ 10.743469] systemd[1]: Queued start job for default target Graphical Interface. [ 10.752727] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.765239] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 10.774544] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 10.807771] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 10.847940] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.886921] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 10.927214] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 10.967322] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 11.006737] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.018684] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 11.057370] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 11.086878] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 11.126724] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 11.156916] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 11.187640] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 11.262646] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 11.272972] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 11.308053] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 11.349385] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 11.390658] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 11.428061] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 11.467666] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 11.477121] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.526832] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 11.560248] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 11.601755] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 11.687656] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 11.730469] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 11.770445] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 11.810087] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 11.823310] systemd[1]: Starting Journal Service... Starting Journal Service... [ 11.865186] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 11.899917] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 11.940005] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 11.982690] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 12.017042] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 12.056990] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Create list of st… nodes for the current kernel. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... [ 12.456413] systemd-journald[237]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Sound Card. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 6.1.31 #1 SMP Mon Jun 5 22:04:32 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent p[ 18.429840] platform backlight-lcd: deferred probe pending ermitted by applicable law. [ 18.435841] platform backlight-lvds: deferred probe pending [ 18.443944] platform disp0: deferred probe pending [ 18.448958] platform panel-lcd: deferred probe pending [ 18.454183] platform ldb: deferred probe pending [ 18.458933] platform panel-lvds0: deferred probe pending / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10597217/extract-nfsrootfs-hvn33nd4' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10597217/extract-nfsrootfs-hvn33nd4' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10597217/environment . /lava-10597217/environment / # /lava-10597217/bin/lava-test-runner /lava-10597217/0 /lava-10597217/bin/lava-test-runner /lava-10597217/0 + export TESTRUN_ID=0_dmesg + cd /lava-10597217/0/tests/0_dmesg + cat uuid + UUID=10597217_1.6.2.4.1[ 26.976121] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 27.072178] [ 27.149200] [ 27.225920] + set[ 27.235323] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10597217/environment / # . /lava-10597217/environment/lava-10597217/bin/lava-test-runner /lava-10597217/1 / # /lava-10597217/bin/lava-test-runner /lava-10597217/1 + export TESTRUN_ID=1_bootrr + cd /lava-10597217/1/tests/1_bootrr + cat uuid + UUID=10597217_1.6.2.4.5[ 27.828477] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10597217/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds disp0 panel-lcd platform: supplier backlight-lcd not ready ldb panel-lvds0 platform: supplier backlight-lvds not ready /lava-10597217/1/../bin/lava-test-case [ 28.980655] /lava-10597217/1/../bin/lava-test-case [ 29.057157] /lava-10597217/1/../bin/lava-test-case [ 29.108802] + set[ 29.138710] +x / #