[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.191 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10860267/tftp-deploy-hidm5nvp/kernel/zImage tftp 0x10000000 10860267/tftp-deploy-hidm5nvp/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '10860267/tftp-deploy-hidm5nvp/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 2.9 MiB/s done Bytes transferred = 10347008 (9de200 hex) => tftp 0x14000000 10860267/tftp-deploy-hidm5nvp/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10860267/tftp-deploy-hidm5nvp/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '10860267/tftp-deploy-hidm5nvp/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 2.9 MiB/s done Bytes transferred = 13237648 (c9fd90 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10860267/tftp-deploy-hidm5nvp/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10860267/tftp-deploy-hidm5nvp/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '10860267/tftp-deploy-hidm5nvp/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.3 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10860267/extract-nfsrootfs-iqbe6px9,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10860267/extract-nfsrootfs-iqbe6px9,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9de200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13237584 Bytes = 12.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.31 (KernelCI@build-j77256-arm-gcc-10-multi-v7-defconfig-rqnhb) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jun 22 12:05:40 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10860267/extract-nfsrootfs-iqbe6px9,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 934224K/1048576K available (14336K kernel code, 2468K rwdata, 6008K rodata, 2048K init, 429K bss, 48816K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000000] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008089] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021983] Console: colour dummy device 80x30 <6>[ 0.023891] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034553] pid_max: default: 32768 minimum: 301 <6>[ 0.039603] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047005] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055598] CPU: Testing write buffer coherency: ok <6>[ 0.060117] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065738] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072226] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079779] rcu: Hierarchical SRCU implementation. <6>[ 0.083172] rcu: Max phase no-delay instances is 1000. <6>[ 0.092263] EFI services will not be available. <6>[ 0.094573] smp: Bringing up secondary CPUs ... <6>[ 0.099821] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099837] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.111133] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.111148] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.122344] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.122361] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.132763] smp: Brought up 1 node, 4 CPUs <6>[ 0.137026] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.143531] CPU: All CPU(s) started in SVC mode. <6>[ 0.149008] devtmpfs: initialized <6>[ 0.159852] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.165153] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.175079] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.185721] pinctrl core: initialized pinctrl subsystem <6>[ 0.192016] DMI not present or invalid. <6>[ 0.194072] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.202946] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.209931] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.209999] cpuidle: using governor menu <6>[ 0.217956] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.231484] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.236515] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.266397] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2100000/i2c@21a4000/camera@40 <6>[ 0.283207] platform 2400000.ipu: Fixed dependency cycle(s) with /disp0 <6>[ 0.287760] platform disp0: Fixed dependency cycle(s) with /panel-lcd <6>[ 0.294434] platform ldb: Fixed dependency cycle(s) with /panel-lvds0 <6>[ 0.302099] No ATAGs? <6>[ 0.303313] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.311451] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.320802] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.332413] Serial: AMBA PL011 UART driver <6>[ 0.336776] printk: console [ramoops-1] enabled <6>[ 0.338957] pstore: Registered ramoops as persistent store backend <6>[ 0.345159] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.383206] iommu: Default domain type: Translated <6>[ 0.385507] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.392883] SCSI subsystem initialized <6>[ 0.396589] usbcore: registered new interface driver usbfs <6>[ 0.401814] usbcore: registered new interface driver hub <6>[ 0.407444] usbcore: registered new device driver usb <4>[ 0.412882] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.420730] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.429166] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.437082] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.447372] i2c i2c-0: IMX I2C adapter registered <6>[ 0.451673] i2c i2c-1: IMX I2C adapter registered <6>[ 0.456210] i2c i2c-2: IMX I2C adapter registered <6>[ 0.461676] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.465457] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.474890] PTP clock support registered <6>[ 0.479298] EDAC MC: Ver: 3.0.0 <6>[ 0.486300] vgaarb: loaded <6>[ 1.599479] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.613152] NET: Registered PF_INET protocol family <6>[ 1.616024] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.625290] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 1.631810] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.639799] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.647827] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 1.655573] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.662129] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.668744] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.676298] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.682717] RPC: Registered named UNIX socket transport module. <6>[ 1.688104] RPC: Registered udp transport module. <6>[ 1.693109] RPC: Registered tcp transport module. <6>[ 1.698020] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.704756] PCI: CLS 0 bytes, default 64 <6>[ 1.709470] Trying to unpack rootfs image as initramfs... <4>[ 1.709623] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 1.722825] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.732887] Initialise system trusted keyrings <6>[ 1.735899] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.748407] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.752530] NFS: Registering the id_resolver key type <5>[ 1.757021] Key type id_resolver registered <5>[ 1.761451] Key type id_legacy registered <6>[ 1.765795] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.772664] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.780378] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.785496] Key type asymmetric registered <5>[ 1.789251] Asymmetric key parser 'x509' registered <6>[ 1.794597] bounce: pool size: 64 pages <6>[ 1.798603] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.806170] io scheduler mq-deadline registered <6>[ 1.810928] io scheduler kyber registered <6>[ 1.866987] mxs-dma 110000.dma-apbh: initialized <6>[ 1.946353] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.955419] SuperH (H)SCI(F) driver initialized <6>[ 1.958563] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 269, base_baud = 5000000) is a IMX <6>[ 1.967490] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 270, base_baud = 5000000) is a IMX <6>[ 1.975406] printk: console [ttymxc1] enabled <6>[ 1.975406] printk: console [ttymxc1] enabled <6>[ 1.984540] printk: bootconsole [ec_imx21] disabled <6>[ 1.984540] printk: bootconsole [ec_imx21] disabled <6>[ 1.996443] msm_serial: driver initialized <6>[ 2.002078] STMicroelectronics ASC driver initialized <6>[ 2.009323] STM32 USART driver initialized <6>[ 2.036316] brd: module loaded <6>[ 2.047150] loop: module loaded <6>[ 2.054690] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.062938] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.071241] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.079714] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 2.087764] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 2.095606] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 2.103235] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 2.114014] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.121318] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.130412] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.141689] scsi host0: ahci-imx <6>[ 2.145591] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 <6>[ 2.167724] CAN device driver interface <6>[ 2.173806] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.183831] pps pps0: new PPS source ptp0 <3>[ 2.190822] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address <6>[ 2.198250] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 <6>[ 2.205635] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 <6>[ 2.213004] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 <6>[ 2.220349] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 <6>[ 2.227672] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 <6>[ 2.235024] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 <6>[ 2.242374] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 <6>[ 2.481147] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.486900] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.493495] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.777305] Freeing initrd memory: 12928K <4>[ 2.781986] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.792693] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 2.802974] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.810640] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.815881] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.822159] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.827832] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.840604] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.846498] usbcore: registered new interface driver pegasus <6>[ 2.852503] usbcore: registered new interface driver asix <6>[ 2.858211] usbcore: registered new interface driver ax88179_178a <6>[ 2.864631] usbcore: registered new interface driver cdc_ether <6>[ 2.870801] usbcore: registered new interface driver smsc75xx <6>[ 2.876864] usbcore: registered new interface driver smsc95xx <6>[ 2.882939] usbcore: registered new interface driver net1080 <6>[ 2.888913] usbcore: registered new interface driver cdc_subset <6>[ 2.895160] usbcore: registered new interface driver zaurus <6>[ 2.901096] usbcore: registered new interface driver cdc_ncm <6>[ 2.913991] usbcore: registered new interface driver usb-storage <6>[ 2.929081] i2c_dev: i2c /dev entries driver <6>[ 2.958024] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.964531] sdhci: Copyright(c) Pierre Ossman <6>[ 2.972237] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.981207] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.988598] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 2.988818] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 2.999162] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.004648] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.013030] usbcore: registered new interface driver usbhid <6>[ 3.018883] usbhid: USB HID core driver <6>[ 3.033332] NET: Registered PF_INET6 protocol family <6>[ 3.036517] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.039980] Segment Routing with IPv6 <6>[ 3.049746] In-situ OAM (IOAM) with IPv6 <6>[ 3.054026] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.060881] NET: Registered PF_PACKET protocol family <6>[ 3.066212] can: controller area network core <6>[ 3.070504] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.070926] NET: Registered PF_CAN protocol family <6>[ 3.083061] can: raw protocol <6>[ 3.086304] can: broadcast manager protocol <6>[ 3.090780] can: netlink gateway - max_hops=1 <5>[ 3.095814] Key type dns_resolver registered <6>[ 3.102292] ThumbEE CPU extension supported. <5>[ 3.106850] Registering SWP/SWPB emulation handler <5>[ 3.112646] Loading compiled-in X.509 certificates <6>[ 3.113077] mmc2: new high speed SDHC card at address 0001 <6>[ 3.123640] pstore: Using crash dump compression: deflate <6>[ 3.124959] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 3.164172] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.174395] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.179617] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 3.190375] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.198051] GPT:29296874 != 30560255 <4>[ 3.201925] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.208200] GPT:29296874 != 30560255 <4>[ 3.212071] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.217578] mmcblk2: p1 p2 p3 <6>[ 3.219487] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.227345] hub 1-0:1.0: USB hub found <6>[ 3.231445] hub 1-0:1.0: 1 port detected <3>[ 3.238193] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 3.245832] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 3.254220] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <6>[ 3.270642] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 3.287533] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 3.519551] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.721149] hub 1-1:1.0: USB hub found <6>[ 3.725367] hub 1-1:1.0: 3 ports detected <6>[ 5.359918] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 5.367913] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.409518] Sending DHCP requests ., OK <6>[ 5.453700] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.191 <6>[ 5.462161] IP-Config: Complete: <6>[ 5.465676] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.191, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.476553] host=192.168.201.191, domain=lava-rack, nis-domain=(none) <6>[ 5.483764] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.483787] nameserver0=192.168.201.1 <6>[ 5.503011] Freeing unused kernel image (initmem) memory: 2048K <6>[ 5.530517] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 6.681325] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 6.727318] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 6.763338] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 6.801034] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.808470] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.825574] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.832594] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.839589] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 6.879021] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.885469] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.901100] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 6.923845] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 6.977507] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.043700] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 7.104463] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.109945] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.116863] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 7.138979] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.148989] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <3>[ 7.249654] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' <6>[ 7.685147] caam algorithms registered in /proc/crypto <6>[ 7.692350] caam 2100000.crypto: registering rng-caam <6>[ 7.698090] caam 2100000.crypto: rng crypto API alg registered prng-caam Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. <5>[ 7.880122] random: crng init done IP-Config: eth0 hardware address 0e:cc:7b:b0:7c:c7 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.191 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.998251] systemd[1]: System time before build time, advancing clock. <30>[ 9.094588] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 9.118733] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 9.172489] systemd[1]: Set hostname to . <30>[ 10.241081] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 10.250423] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 10.263349] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 10.273120] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 10.310942] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 10.350926] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 10.390620] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 10.430341] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 10.470316] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 10.510231] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 10.522752] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 10.560572] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 10.589882] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 10.629864] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 10.660000] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 10.690835] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 10.770347] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 10.781383] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 10.831174] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 10.872358] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 10.913719] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 10.950981] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.990820] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.000489] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.050229] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 11.096428] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 11.142734] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 11.183646] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 11.226931] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 11.263631] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 11.305506] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 11.322430] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 11.430437] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 11.464022] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 11.503609] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 11.545479] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 11.560292] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 11.602392] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Create list of st… nodes for the current kernel. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply <46>[ 12.056967] systemd-journald[243]: Received client request to flush runtime journal. Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. <6>[ 17.774199] platform panel-lvds0: deferred probe pending <6>[ 17.779828] platform backlight-lcd: deferred probe pending <6>[ 17.785591] platform ldb: deferred probe pending <6>[ 17.790509] platform backlight-lvds: deferred probe pending <6>[ 17.796555] platform panel-lcd: deferred probe pending <6>[ 17.802725] platform disp0: deferred probe pending [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Sound Card. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 6.1.31 #1 SMP Thu Jun 22 12:05:40 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10860267/extract-nfsrootfs-iqbe6px9' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10860267/extract-nfsrootfs-iqbe6px9' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-10860267/environment . /lava-10860267/environment / # /lava-10860267/bin/lava-test-runner /lava-10860267/0 /lava-10860267/bin/lava-test-runner /lava-10860267/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-10860267/0/tests/0_timesync-off ++ cat uuid + UUID=10860267_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-10860267/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=10860267_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v6.1.31-61-g32a95f5a4e3b/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-06-22 12:14:55-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v6.1.31-61-g32a95f5a4e3b/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1447224 (1.4M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 43.57K 170KB/s kselftest.tar.xz 15%[==> ] 214.67K 418KB/s kselftest.tar.xz 48%[========> ] 689.79K 893KB/s kselftest.tar.xz 79%[==============> ] 1.09M 1.06MB/s kselftest.tar.xz 100%[===================>] 1.38M 1.18MB/s in 1.2s 2023-06-22 12:14:57 (1.18 MB/s) - 'kselftest.tar.xz' saved [1447224/1447224] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== <12>[ 39.192104] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #