[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11111701/tftp-deploy-ysogfzk3/kernel/zImage tftp 0x10000000 11111701/tftp-deploy-ysogfzk3/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11111701/tftp-deploy-ysogfzk3/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 14.4 MiB/s done Bytes transferred = 10347008 (9de200 hex) => tftp 0x14000000 11111701/tftp-deploy-ysogfzk3/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11111701/tftp-deploy-ysogfzk3/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11111701/tftp-deploy-ysogfzk3/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 11 MiB/s done Bytes transferred = 13235241 (c9f429 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11111701/tftp-deploy-ysogfzk3/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11111701/tftp-deploy-ysogfzk3/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '11111701/tftp-deploy-ysogfzk3/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.8 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11111701/extract-nfsrootfs-fsggbrs7,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11111701/extract-nfsrootfs-fsggbrs7,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9de200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13235177 Bytes = 12.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.38-cip1 (KernelCI@build-j5365-arm-gcc-10-multi-v7-defconfig-94k72) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Jul 19 12:25:25 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11111701/extract-nfsrootfs-fsggbrs7,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 934224K/1048576K available (14336K kernel code, 2468K rwdata, 6008K rodata, 2048K init, 429K bss, 48816K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000018] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004079] Console: colour dummy device 80x30 [ 0.004141] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004156] pid_max: default: 32768 minimum: 301 [ 0.004349] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004373] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005007] CPU: Testing write buffer coherency: ok [ 0.005063] CPU0: Spectre v2: using BPIALL workaround [ 0.005375] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006270] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007917] rcu: Hierarchical SRCU implementation. [ 0.007923] rcu: Max phase no-delay instances is 1000. [ 0.011573] EFI services will not be available. [ 0.011951] smp: Bringing up secondary CPUs ... [ 0.012781] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012797] CPU1: Spectre v2: using BPIALL workaround [ 0.013723] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013739] CPU2: Spectre v2: using BPIALL workaround [ 0.014649] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014665] CPU3: Spectre v2: using BPIALL workaround [ 0.014762] smp: Brought up 1 node, 4 CPUs [ 0.014773] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.014783] CPU: All CPU(s) started in SVC mode. [ 0.015355] devtmpfs: initialized [ 0.023406] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.023632] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.023656] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.026959] pinctrl core: initialized pinctrl subsystem [ 0.030694] DMI not present or invalid. [ 0.031514] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.035064] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.037723] thermal_sys: Registered thermal governor 'step_wise' [ 0.037790] cpuidle: using governor menu [ 0.038037] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.046984] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2800000 [ 0.047106] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2400000 [ 0.069529] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2100000/i2c@21a4000/camera@40 [ 0.079442] platform 2400000.ipu: Fixed dependency cycle(s) with /disp0 [ 0.079948] platform disp0: Fixed dependency cycle(s) with /panel-lcd [ 0.080456] platform ldb: Fixed dependency cycle(s) with /panel-lvds0 [ 0.081932] No ATAGs? [ 0.082084] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.082096] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.085416] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.092794] Serial: AMBA PL011 UART driver [ 0.095534] printk: console [ramoops-1] enabled [ 0.095779] pstore: Registered ramoops as persistent store backend [ 0.095795] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.135039] iommu: Default domain type: Translated [ 0.135064] iommu: DMA domain TLB invalidation policy: strict mode [ 0.135878] SCSI subsystem initialized [ 0.136407] usbcore: registered new interface driver usbfs [ 0.136465] usbcore: registered new interface driver hub [ 0.136514] usbcore: registered new device driver usb [ 0.136764] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 0.136915] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 0.137080] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 0.137220] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 0.139191] i2c i2c-0: IMX I2C adapter registered [ 0.140578] i2c i2c-1: IMX I2C adapter registered [ 0.141477] i2c i2c-2: IMX I2C adapter registered [ 0.142963] pps_core: LinuxPPS API ver. 1 registered [ 0.142979] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.143007] PTP clock support registered [ 0.143272] EDAC MC: Ver: 3.0.0 [ 0.147154] vgaarb: loaded [ 1.336306] clocksource: Switched to clocksource mxc_timer1 [ 1.347690] NET: Registered PF_INET protocol family [ 1.348243] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.350241] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.350288] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.350315] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.350409] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 1.350753] TCP: Hash tables configured (established 8192 bind 8192) [ 1.351009] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.351077] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.351325] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.352076] RPC: Registered named UNIX socket transport module. [ 1.352102] RPC: Registered udp transport module. [ 1.352112] RPC: Registered tcp transport module. [ 1.352122] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.352139] PCI: CLS 0 bytes, default 64 [ 1.352912] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. [ 1.353039] Trying to unpack rootfs image as initramfs... [ 1.378318] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.380458] Initialise system trusted keyrings [ 1.380825] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.387034] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.387806] NFS: Registering the id_resolver key type [ 1.387855] Key type id_resolver registered [ 1.387869] Key type id_legacy registered [ 1.387967] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.387985] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.388032] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.388556] Key type asymmetric registered [ 1.388576] Asymmetric key parser 'x509' registered [ 1.388746] bounce: pool size: 64 pages [ 1.388866] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.388884] io scheduler mq-deadline registered [ 1.388897] io scheduler kyber registered [ 1.439826] mxs-dma 110000.dma-apbh: initialized [ 1.521852] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 1.527291] SuperH (H)SCI(F) driver initialized [ 1.528415] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 269, base_baud = 5000000) is a IMX [ 1.529462] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 270, base_baud = 5000000) is a IMX [ 2.423029] Freeing initrd memory: 12928K [ 2.424105] printk: console [ttymxc1] enabled [ 2.433041] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.443471] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware [ 2.444742] msm_serial: driver initialized [ 2.456057] STMicroelectronics ASC driver initialized [ 2.462964] STM32 USART driver initialized [ 2.489303] brd: module loaded [ 2.499858] loop: module loaded [ 2.507139] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.515080] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.523122] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.531328] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.539082] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 2.546573] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 2.553862] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 2.564284] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.571306] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.580128] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.590830] scsi host0: ahci-imx [ 2.594407] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 [ 2.615842] CAN device driver interface [ 2.621550] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.631064] pps pps0: new PPS source ptp0 [ 2.637168] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address [ 2.644324] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 [ 2.651410] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 [ 2.658483] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 [ 2.665537] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 [ 2.672609] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 [ 2.679679] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 [ 2.686747] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 [ 2.693800] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 7 [ 2.716290] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.723650] e1000e: Intel(R) PRO/1000 Network Driver [ 2.728648] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.734640] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.740074] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.752513] pegasus: Pegasus/Pegasus II USB Ethernet driver [ 2.758168] usbcore: registered new interface driver pegasus [ 2.763889] usbcore: registered new interface driver asix [ 2.769352] usbcore: registered new interface driver ax88179_178a [ 2.775487] usbcore: registered new interface driver cdc_ether [ 2.781388] usbcore: registered new interface driver smsc75xx [ 2.787202] usbcore: registered new interface driver smsc95xx [ 2.792992] usbcore: registered new interface driver net1080 [ 2.798718] usbcore: registered new interface driver cdc_subset [ 2.804682] usbcore: registered new interface driver zaurus [ 2.810346] usbcore: registered new interface driver cdc_ncm [ 2.822949] usbcore: registered new interface driver usb-storage [ 2.837895] i2c_dev: i2c /dev entries driver [ 2.866869] sdhci: Secure Digital Host Controller Interface driver [ 2.873068] sdhci: Copyright(c) Pierre Ossman [ 2.880547] Synopsys Designware Multimedia Card Interface Driver [ 2.889283] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.896411] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 2.897183] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 2.901440] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 2.911723] ledtrig-cpu: registered to indicate activity on CPUs [ 2.919937] usbcore: registered new interface driver usbhid [ 2.925525] usbhid: USB HID core driver [ 2.928379] ata1: SATA link down (SStatus 0 SControl 300) [ 2.934813] ahci-imx 2200000.sata: no device found, disabling link. [ 2.939695] NET: Registered PF_INET6 protocol family [ 2.941126] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 2.946671] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 2.947686] Segment Routing with IPv6 [ 2.947745] In-situ OAM (IOAM) with IPv6 [ 2.947828] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.948469] NET: Registered PF_PACKET protocol family [ 2.948478] can: controller area network core [ 2.948548] NET: Registered PF_CAN protocol family [ 2.948557] can: raw protocol [ 2.948565] can: broadcast manager protocol [ 2.948576] can: netlink gateway - max_hops=1 [ 2.948937] Key type dns_resolver registered [ 2.955297] ThumbEE CPU extension supported. [ 2.964165] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 2.967806] Registering SWP/SWPB emulation handler [ 3.005130] mmc2: new high speed SDHC card at address aaaa [ 3.008666] Loading compiled-in X.509 certificates [ 3.015776] mmcblk2: mmc2:aaaa SL16G 14.8 GiB [ 3.031706] pstore: Using crash dump compression: deflate [ 3.052569] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.060063] GPT:7812499 != 31116287 [ 3.063568] GPT:Alternate GPT header not at the end of the disk. [ 3.069604] GPT:7812499 != 31116287 [ 3.073100] GPT: Use GNU Parted to correct GPT errors. [ 3.078334] mmcblk2: p1 p2 p3 [ 3.085017] imx_usb 2184200.usb: No over current polarity defined [ 3.094952] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.099961] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.136163] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.143056] hub 1-0:1.0: USB hub found [ 3.146973] hub 1-0:1.0: 1 port detected [ 3.155886] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 3.173891] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.191613] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.436187] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.637894] hub 1-1:1.0: USB hub found [ 3.641848] hub 1-1:1.0: 3 ports detected [ 6.326607] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.334167] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.376182] Sending DHCP requests ., OK [ 6.420119] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 [ 6.428187] IP-Config: Complete: [ 6.431423] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 [ 6.441896] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) [ 6.449764] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.449774] nameserver0=192.168.201.1 [ 6.467437] Freeing unused kernel image (initmem) memory: 2048K [ 6.497280] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 [ 7.432291] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.443881] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.460201] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) [ 7.492365] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.500978] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.507914] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.514561] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.521049] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.527163] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.533302] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.556250] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.600351] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW [ 7.671115] caam 2100000.crypto: Entropy delay = 3200 [ 7.704722] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.736639] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.737034] caam 2100000.crypto: Instantiated RNG4 SH0 [ 7.797798] caam 2100000.crypto: Instantiated RNG4 SH1 [ 7.802989] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 7.809661] caam 2100000.crypto: job rings = 2, qi = 0 [ 7.842850] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' [ 8.214251] caam algorithms registered in /proc/crypto [ 8.221523] caam 2100000.crypto: registering rng-caam [ 8.226955] caam 2100000.crypto: rng crypto API alg registered prng-caam Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: [ 8.409064] random: crng init done 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.086020] systemd[1]: System time before build time, advancing clock. [ 9.146417] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 9.170151] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 9.218223] systemd[1]: Set hostname to . [ 10.334799] systemd[1]: Queued start job for default target Graphical Interface. [ 10.343755] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.356303] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 10.365608] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 10.407675] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 10.447657] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.487321] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 10.527199] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 10.567144] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.606512] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.618468] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 10.656966] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 10.686602] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 10.726506] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 10.756705] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 10.787472] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.860055] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 10.870230] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 10.907844] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 10.948636] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 10.989476] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 11.027681] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 11.067450] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 11.076709] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.137037] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 11.180093] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 11.466935] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 11.509634] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 11.550334] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 11.590331] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 11.629475] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 11.642804] systemd[1]: Starting Journal Service... Starting Journal Service... [ 11.683652] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 11.720843] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 11.759876] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 11.802074] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 11.836910] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 11.876728] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Create list of st… nodes for the current kernel. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 12.303150] systemd-journald[238]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Sound Card. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 6.1.38-cip1 #1 SMP Wed Jul 19 12:25:25 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11111701/extract-nfsrootfs-fsggbrs7' [ 18.430666] platform disp0: deferred probe pending [ 18.435489] platform ldb: deferred probe pending [ 18.440172] platform panel-lvds0: deferred probe pending [ 18.445499] platform backlight-lcd: deferred probe pending [ 18.451042] platform backlight-lvds: deferred probe pending [ 18.456661] platform panel-lcd: deferred probe pending export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11111701/extract-nfsrootfs-fsggbrs7' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11111701/environment . /lava-11111701/environment / # /lava-11111701/bin/lava-test-runner /lava-11111701/0 /lava-11111701/bin/lava-test-runner /lava-11111701/0 + export TESTRUN_ID=0_dmesg + cd /lava-11111701/0/tests/0_dmesg + cat uuid + UUID=11111701_1.6.2.4.1[ 26.627345] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 26.726809] [ 26.808880] [ 26.893753] + set[ 26.903286] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11111701/environment / # . /lava-11111701/environment/lava-11111701/bin/lava-test-runner /lava-11111701/1 / # /lava-11111701/bin/lava-test-runner /lava-11111701/1 + export TESTRUN_ID=1_bootrr + cd /lava-11111701/1/tests/1_bootrr + cat uuid + UUID=11111701_1.6.2.4.5[ 27.483343] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11111701/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto disp0 ldb panel-lvds0 platform: supplier backlight-lvds not ready backlight-lcd backlight-lvds panel-lcd platform: supplier backlight-lcd not ready /lava-11111701/1/../bin/lava-test-case [ 28.828176] /lava-11111701/1/../bin/lava-test-case [ 28.894816] /lava-11111701/1/../bin/lava-test-case [ 28.939155] + set[ 28.992496] +x / #