[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11089937/tftp-deploy-qo2l8wjo/kernel/zImage tftp 0x10000000 11089937/tftp-deploy-qo2l8wjo/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '11089937/tftp-deploy-qo2l8wjo/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 11 MiB/s done Bytes transferred = 10351104 (9df200 hex) => tftp 0x14000000 11089937/tftp-deploy-qo2l8wjo/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11089937/tftp-deploy-qo2l8wjo/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '11089937/tftp-deploy-qo2l8wjo/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################## 10.6 MiB/s done Bytes transferred = 13242547 (ca10b3 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11089937/tftp-deploy-qo2l8wjo/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11089937/tftp-deploy-qo2l8wjo/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '11089937/tftp-deploy-qo2l8wjo/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.7 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11089937/extract-nfsrootfs-km4g6z9s,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11089937/extract-nfsrootfs-km4g6z9s,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x9df200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13242483 Bytes = 12.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.38-cip1-rt1 (KernelCI@build-j2308-arm-gcc-10-multi-v7-defconfig-r6jxb) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Jul 14 20:43:15 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11089937/extract-nfsrootfs-km4g6z9s,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 934216K/1048576K available (14336K kernel code, 2469K rwdata, 6008K rodata, 2048K init, 428K bss, 48824K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022339] Console: colour dummy device 80x30 <6>[ 0.024248] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034648] pid_max: default: 32768 minimum: 301 <6>[ 0.039701] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047101] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055723] CPU: Testing write buffer coherency: ok <6>[ 0.060213] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065840] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072320] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079991] rcu: Hierarchical SRCU implementation. <6>[ 0.079996] rcu: Max phase no-delay instances is 1000. <6>[ 0.080087] printk: bootconsole [ec_imx21] printing thread started <6>[ 0.098719] EFI services will not be available. <6>[ 0.099100] smp: Bringing up secondary CPUs ... <6>[ 0.099923] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099939] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.100854] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.100869] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.101778] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.101793] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.101893] smp: Brought up 1 node, 4 CPUs <6>[ 0.101904] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.101913] CPU: All CPU(s) started in SVC mode. <6>[ 0.102491] devtmpfs: initialized <6>[ 0.110418] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.110644] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.110666] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.113971] pinctrl core: initialized pinctrl subsystem <6>[ 0.117707] DMI not present or invalid. <6>[ 0.118527] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.213613] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.216295] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.220079] cpuidle: using governor menu <6>[ 0.220345] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.229226] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.229347] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.251622] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2100000/i2c@21a4000/camera@40 <6>[ 0.261448] platform 2400000.ipu: Fixed dependency cycle(s) with /disp0 <6>[ 0.261948] platform disp0: Fixed dependency cycle(s) with /panel-lcd <6>[ 0.262442] platform ldb: Fixed dependency cycle(s) with /panel-lvds0 <6>[ 0.263950] No ATAGs? <6>[ 0.286625] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.286636] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.289926] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.297277] Serial: AMBA PL011 UART driver <6>[ 0.301877] printk: console [ramoops-1] enabled <6>[ 0.301915] printk: console [ramoops-1] printing thread started <6>[ 0.302119] pstore: Registered ramoops as persistent store backend <6>[ 0.302126] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.373066] iommu: Default domain type: Translated <6>[ 0.373077] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.373868] SCSI subsystem initialized <6>[ 0.374366] usbcore: registered new interface driver usbfs <6>[ 0.374412] usbcore: registered new interface driver hub <6>[ 0.374452] usbcore: registered new device driver usb <4>[ 0.374687] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.374820] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.374971] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.375100] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.377046] i2c i2c-0: IMX I2C adapter registered <6>[ 0.378407] i2c i2c-1: IMX I2C adapter registered <6>[ 0.379311] i2c i2c-2: IMX I2C adapter registered <6>[ 0.380753] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.380759] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.380777] PTP clock support registered <6>[ 0.381073] EDAC MC: Ver: 3.0.0 <6>[ 0.385060] vgaarb: loaded <6>[ 1.579393] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.589844] NET: Registered PF_INET protocol family <6>[ 1.590354] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.592348] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 1.592381] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.592398] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.592490] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 1.592822] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.593077] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.593135] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.593373] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.594128] RPC: Registered named UNIX socket transport module. <6>[ 1.594138] RPC: Registered udp transport module. <6>[ 1.594143] RPC: Registered tcp transport module. <6>[ 1.594147] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.594159] PCI: CLS 0 bytes, default 64 <4>[ 1.594865] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 1.595379] Trying to unpack rootfs image as initramfs... <6>[ 1.709551] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.711675] Initialise system trusted keyrings <6>[ 1.712018] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.717987] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.718774] NFS: Registering the id_resolver key type <5>[ 1.718864] Key type id_resolver registered <5>[ 1.718870] Key type id_legacy registered <6>[ 1.718962] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.718971] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.719007] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.719639] Key type asymmetric registered <5>[ 1.719650] Asymmetric key parser 'x509' registered <6>[ 1.719810] bounce: pool size: 64 pages <6>[ 1.719918] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.719927] io scheduler mq-deadline registered <6>[ 1.719933] io scheduler kyber registered <6>[ 1.857772] mxs-dma 110000.dma-apbh: initialized <6>[ 1.934511] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.943170] printk: console [ttymxc1] enabled <6>[ 1.943176] printk: console [ttymxc1] printing thread started <6>[ 1.943179] printk: bootconsole [ec_imx21] disabled <6>[ 1.949261] printk: bootconsole [ec_imx21] printing thread stopped <6>[ 1.951997] msm_serial: driver initialized <6>[ 1.952005] STMicroelectronics ASC driver initialized <6>[ 1.953784] STM32 USART driver initialized <6>[ 1.976312] brd: module loaded <6>[ 1.983983] loop: module loaded <6>[ 1.988144] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.988161] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.988170] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.988179] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 1.988272] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 1.988433] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 1.988497] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 1.991416] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.991448] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.991465] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.071818] scsi host0: ahci-imx <6>[ 2.072176] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 <6>[ 2.085896] CAN device driver interface <6>[ 2.087688] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.091622] pps pps0: new PPS source ptp0 <3>[ 2.107609] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address <6>[ 2.107627] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 <6>[ 2.107725] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 <6>[ 2.107808] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 <6>[ 2.107893] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 <6>[ 2.107977] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 <6>[ 2.108059] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 <6>[ 2.108142] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 <6>[ 2.108225] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 7 <6>[ 2.420901] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.420975] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.420985] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.660558] Freeing initrd memory: 12936K <4>[ 2.660936] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.660976] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 2.690376] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.691889] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.691894] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.691955] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.691960] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.698786] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.698837] usbcore: registered new interface driver pegasus <6>[ 2.698883] usbcore: registered new interface driver asix <6>[ 2.698916] usbcore: registered new interface driver ax88179_178a <6>[ 2.698950] usbcore: registered new interface driver cdc_ether <6>[ 2.698992] usbcore: registered new interface driver smsc75xx <6>[ 2.699036] usbcore: registered new interface driver smsc95xx <6>[ 2.699076] usbcore: registered new interface driver net1080 <6>[ 2.699113] usbcore: registered new interface driver cdc_subset <6>[ 2.699144] usbcore: registered new interface driver zaurus <6>[ 2.699273] usbcore: registered new interface driver cdc_ncm <6>[ 2.706231] usbcore: registered new interface driver usb-storage <6>[ 2.715087] i2c_dev: i2c /dev entries driver <6>[ 2.739568] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.739575] sdhci: Copyright(c) Pierre Ossman <6>[ 2.742604] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.745245] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.746657] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 2.746896] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 2.746929] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 2.837562] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.839840] usbcore: registered new interface driver usbhid <6>[ 2.839848] usbhid: USB HID core driver <6>[ 2.850128] NET: Registered PF_INET6 protocol family <6>[ 2.851578] Segment Routing with IPv6 <6>[ 2.851637] In-situ OAM (IOAM) with IPv6 <6>[ 2.851724] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.852364] NET: Registered PF_PACKET protocol family <6>[ 2.852372] can: controller area network core <6>[ 2.852440] NET: Registered PF_CAN protocol family <6>[ 2.852448] can: raw protocol <6>[ 2.852456] can: broadcast manager protocol <6>[ 2.852467] can: netlink gateway - max_hops=1 <5>[ 2.852811] Key type dns_resolver registered <6>[ 2.857547] ThumbEE CPU extension supported. <5>[ 2.857563] Registering SWP/SWPB emulation handler <5>[ 2.861012] Loading compiled-in X.509 certificates <6>[ 2.869598] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 2.870233] pstore: Using crash dump compression: deflate <6>[ 2.882409] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 2.930527] mmc2: new high speed SDHC card at address e624 <6>[ 2.931407] mmcblk2: mmc2:e624 SL16G 14.8 GiB <4>[ 2.939433] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.939440] GPT:29296874 != 31116287 <4>[ 2.939445] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.939448] GPT:29296874 != 31116287 <4>[ 2.939451] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.939535] mmcblk2: p1 p2 p3 <4>[ 2.985729] imx_usb 2184200.usb: No over current polarity defined <6>[ 2.989329] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.989367] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.039285] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.040824] hub 1-0:1.0: USB hub found <6>[ 3.040903] hub 1-0:1.0: 1 port detected <6>[ 3.045939] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 3.064812] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 3.081746] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.329309] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.531043] hub 1-1:1.0: USB hub found <6>[ 3.531245] hub 1-1:1.0: 3 ports detected <6>[ 6.239709] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.239770] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.269320] Sending DHCP requests ., OK <6>[ 6.309349] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 6.309374] IP-Config: Complete: <6>[ 6.309380] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.309405] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 6.309419] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.309432] nameserver0=192.168.201.1 <6>[ 6.318110] Freeing unused kernel image (initmem) memory: 2048K <6>[ 6.390238] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 7.319404] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.322292] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 7.446052] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 7.497952] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.506262] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.513649] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.513781] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.514128] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.514202] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.514215] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.519684] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 7.618415] caam 2100000.crypto: Entropy delay = 3200 <4>[ 7.630086] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 7.679218] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 7.702772] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.706993] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.739980] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.740013] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.740025] caam 2100000.crypto: job rings = 2, qi = 0 <3>[ 7.801529] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' <6>[ 8.146495] caam algorithms registered in /proc/crypto <6>[ 8.147955] caam 2100000.crypto: registering rng-caam <6>[ 8.148315] caam 2100000.crypto: rng crypto API alg registered prng-caam Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f0:fd mtu 1500 DHCP IP-Config: eth0 complete (dhcp fr<5>[ 8.330407] random: crng init done om 192.168.201.1): address: 192.168.201.37 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-7 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 9.393075] systemd[1]: System time before build time, advancing clock. Welcome to Debian GNU/Linux<30>[ 9.481356] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) 11 (bullseye)! <30>[ 9.482096] systemd[1]: Detected architecture arm. <30>[ 9.542094] systemd[1]: Set hostname to . [ OK ] Created slice<30>[ 10.356175] systemd[1]: Queued start job for default target Graphical Interface. system-getty.slice.<28>[ 10.357637] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 10.357660] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 10.358529] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 10.410874] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 10.440647] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice<30>[ 10.470443] systemd[1]: Created slice User and Session Slice. User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 10.510155] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 10.540276] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. <30>[ 10.570171] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 10.570677] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. <30>[ 10.599755] systemd[1]: Reached target Paths. [ OK ] Reached targe<30>[ 10.629455] systemd[1]: Reached target Remote File Systems. t Remote File Systems. [ OK ] Reached target Slices. <30>[ 10.669591] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. <30>[ 10.699789] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 10.730514] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on <30>[ 10.796137] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. Journal Socket (/dev/log<30>[ 10.797653] systemd[1]: Listening on Journal Socket (/dev/log). ). [ OK ] Listening on Journal Socket. <30>[ 10.840867] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 10.871697] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. <30>[ 10.902891] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 10.930808] systemd[1]: Listening on udev Kernel Socket. <30>[ 10.960552] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 10.961478] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. Mounting Kernel Debug File System... <30>[ 10.999634] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel<30>[ 11.037347] systemd[1]: Mounting Kernel Trace File System... Trace File System... Starting Create<30>[ 11.074555] systemd[1]: Starting Create list of static device nodes for the current kernel... list of st…odes for the current kernel... Starting Load Kernel Module configfs... <30>[ 11.123439] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module drm... <30>[ 11.153494] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... <30>[ 11.183490] systemd[1]: Starting Load Kernel Module fuse... Starting Journa<30>[ 11.212422] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. l Service... <30>[ 11.216558] systemd[1]: Starting Journal Service... Starting Load Kernel Modules... <30>[ 11.270697] systemd[1]: Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems... <30>[ 11.302935] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Coldplug All udev Devices... <30>[ 11.333502] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0<30>[ 11.365152] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted Kernel Trace File System. <30>[ 11.399983] systemd[1]: Mounted Kernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 11.430554] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Started [0;1<30>[ 11.478219] systemd[1]: Started Journal Service. ;39mJournal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 11.867045] systemd-journald[247]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Sound Card. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 6.1.38-cip1-rt1 #1 SMP Fri Jul 14 20:43:15 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11089937/extract-nfsrootfs-km4g6z9s' expor<6>[ 18.423216] platform panel-lcd: deferred probe pending <6>[ 18.423228] platform ldb: deferred probe pending <6>[ 18.423234] platform panel-lvds0: deferred probe pending <6>[ 18.423239] platform backlight-lcd: deferred probe pending <6>[ 18.423244] platform backlight-lvds: deferred probe pending <6>[ 18.423248] platform disp0: deferred probe pending t NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11089937/extract-nfsrootfs-km4g6z9s' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11089937/environment . /lava-11089937/environment / # /lava-11089937/bin/lava-test-runner /lava-11089937/0 /lava-11089937/bin/lava-test-runner /lava-11089937/0 + export TESTRUN_ID=0_dmesg + cd /lava-11089937/0/tests/0_dmesg + cat uuid + UUID=11089937_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /<8>[ 26.186928] bin/sh /opt/kernelci/dmesg.sh <8>[ 26.271678] <8>[ 26.341485] <8>[ 26.418758] + set +x <8>[ 26.428160] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11089937/environment / # . /lava-11089937/environment/lava-11089937/bin/lava-test-runner /lava-11089937/1 / # /lava-11089937/bin/lava-test-runner /lava-11089937/1 + export TESTRUN_ID=1_bootrr + cd /lava-11089937/1/tests/1_bootrr + cat uuid + UUID=11089937_1.6.2.4.5 + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11089937/1/../bin:/usr/loc<8>[ 27.019807] al/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd platform: supplier backlight-lcd not ready ldb panel-lvds0 platform: supplier backlight-lvds not ready backlight-lcd backlight-lvds disp0 /lava-11089937/1/../bin/lava-test-case <8>[ 28.163459] /lava-11089937/1/../bin/lava-test-case <8>[ 28.238048] /lava-11089937/1/../bin/lava-test-case <8>[ 28.285668] + set +x <8>[ 28.317682] / #