Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.9 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 999445/tftp-deploy-j0ufgmmb/kernel/zImage tftp 0x82000000 999445/tftp-deploy-j0ufgmmb/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '999445/tftp-deploy-j0ufgmmb/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 5.1 MiB/s done Bytes transferred = 10473984 (9fd200 hex) => tftp 0x83000000 999445/tftp-deploy-j0ufgmmb/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 999445/tftp-deploy-j0ufgmmb/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '999445/tftp-deploy-j0ufgmmb/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 5.2 MiB/s done Bytes transferred = 17166522 (105f0ba hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 999445/tftp-deploy-j0ufgmmb/dtb/am335x-boneblack.dtb tftp 0x88000000 999445/tftp-deploy-j0ufgmmb/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '999445/tftp-deploy-j0ufgmmb/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.8 MiB/s done Bytes transferred = 69937 (11131 hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-08-22 15:39:34 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17166458 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 88014130 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.45-cip3 (KernelCI@build-j17693-arm-gcc-10-multi-v7-defconfig-gpbrv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Aug 22 15:18:56 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 408496K/522240K available (14336K kernel code, 2468K rwdata, 6256K rodata, 2048K init, 428K bss, 48208K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008338] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019108] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033833] Console: colour dummy device 80x30 <3>[ 0.038709] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045766] This ensures that you still see kernel messages. Please <3>[ 0.052488] update your kernel commandline. <6>[ 0.057095] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096102] CPU: Testing write buffer coherency: ok <6>[ 0.101466] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106929] pid_max: default: 32768 minimum: 301 <6>[ 0.112137] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.119957] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.129268] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135816] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.145268] rcu: Hierarchical SRCU implementation. <6>[ 0.150532] rcu: Max phase no-delay instances is 1000. <6>[ 0.161303] EFI services will not be available. <6>[ 0.166513] smp: Bringing up secondary CPUs ... <6>[ 0.171487] smp: Brought up 1 node, 1 CPU <6>[ 0.175881] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.182610] CPU: All CPU(s) started in SVC mode. <6>[ 0.188277] devtmpfs: initialized <6>[ 0.204425] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.212959] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.223402] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.235754] pinctrl core: initialized pinctrl subsystem <6>[ 0.246418] DMI not present or invalid. <6>[ 0.251579] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.260532] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.271235] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.271384] cpuidle: using governor menu <6>[ 0.300091] No ATAGs? <6>[ 0.302728] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.314261] Serial: AMBA PL011 UART driver <6>[ 1.426250] iommu: Default domain type: Translated <6>[ 1.431706] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 1.439199] SCSI subsystem initialized <6>[ 1.444173] usbcore: registered new interface driver usbfs <6>[ 1.450192] usbcore: registered new interface driver hub <6>[ 1.455970] usbcore: registered new device driver usb <6>[ 1.462444] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.467827] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.477552] PTP clock support registered <6>[ 1.482038] EDAC MC: Ver: 3.0.0 <6>[ 1.488298] vgaarb: loaded <6>[ 1.492043] clocksource: Switched to clocksource dmtimer <6>[ 1.556026] NET: Registered PF_INET protocol family <6>[ 1.561627] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.570472] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 1.579402] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.587663] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 1.595953] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 1.603667] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 1.610576] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 1.617602] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 1.625204] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.632242] RPC: Registered named UNIX socket transport module. <6>[ 1.638623] RPC: Registered udp transport module. <6>[ 1.643762] RPC: Registered tcp transport module. <6>[ 1.648866] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.655781] PCI: CLS 0 bytes, default 64 <5>[ 1.661507] Initialise system trusted keyrings <6>[ 1.666787] Trying to unpack rootfs image as initramfs... <6>[ 1.712491] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 1.726178] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.752746] NFS: Registering the id_resolver key type <5>[ 1.758330] Key type id_resolver registered <5>[ 1.762969] Key type id_legacy registered <6>[ 1.767490] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.774687] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.782647] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.822675] Key type asymmetric registered <5>[ 1.827195] Asymmetric key parser 'x509' registered <6>[ 1.832758] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 1.840643] io scheduler mq-deadline registered <6>[ 1.845644] io scheduler kyber registered <6>[ 2.019879] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 2.045200] SuperH (H)SCI(F) driver initialized <6>[ 2.050798] msm_serial: driver initialized <6>[ 2.055421] STMicroelectronics ASC driver initialized <6>[ 2.062448] STM32 USART driver initialized <6>[ 2.113166] brd: module loaded <6>[ 2.137017] loop: module loaded <6>[ 2.150546] CAN device driver interface <6>[ 2.155660] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.162522] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.167903] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.174393] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.180215] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.188907] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.195061] usbcore: registered new interface driver pegasus <6>[ 2.201206] usbcore: registered new interface driver asix <6>[ 2.207107] usbcore: registered new interface driver ax88179_178a <6>[ 2.213699] usbcore: registered new interface driver cdc_ether <6>[ 2.220008] usbcore: registered new interface driver smsc75xx <6>[ 2.226272] usbcore: registered new interface driver smsc95xx <6>[ 2.232505] usbcore: registered new interface driver net1080 <6>[ 2.238623] usbcore: registered new interface driver cdc_subset <6>[ 2.245037] usbcore: registered new interface driver zaurus <6>[ 2.251108] usbcore: registered new interface driver cdc_ncm <6>[ 2.260478] usbcore: registered new interface driver usb-storage <6>[ 2.270942] i2c_dev: i2c /dev entries driver <5>[ 2.288069] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 2.297396] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.304175] sdhci: Copyright(c) Pierre Ossman <6>[ 2.310466] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.318280] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.522764] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.532200] usbcore: registered new interface driver usbhid <6>[ 2.538231] usbhid: USB HID core driver <6>[ 2.549552] NET: Registered PF_INET6 protocol family <6>[ 2.593949] Segment Routing with IPv6 <6>[ 2.598072] In-situ OAM (IOAM) with IPv6 <6>[ 2.602583] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.609772] NET: Registered PF_PACKET protocol family <6>[ 2.615308] can: controller area network core <6>[ 2.620141] NET: Registered PF_CAN protocol family <6>[ 2.625366] can: raw protocol <6>[ 2.628690] can: broadcast manager protocol <6>[ 2.633288] can: netlink gateway - max_hops=1 <5>[ 2.638649] Key type dns_resolver registered <6>[ 2.643552] ThumbEE CPU extension supported. <5>[ 2.648230] Registering SWP/SWPB emulation handler <3>[ 2.653910] omap_voltage_late_init: Voltage driver support not added <5>[ 2.733253] Loading compiled-in X.509 certificates <6>[ 2.829734] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <4>[ 2.851525] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 2.968769] ti-sysc: probe of 48040000.target-module failed with error -16 <4>[ 3.009470] gpio gpiochip0: (gpio-0-31): not an immutable chip, please consider fixing it! <6>[ 3.092470] OMAP GPIO hardware version 0.1 <4>[ 3.154329] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 3.187379] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 3.226169] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 3.267721] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 3.305029] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <4>[ 3.319275] gpio gpiochip1: (gpio-32-63): not an immutable chip, please consider fixing it! <4>[ 3.356573] gpio gpiochip2: (gpio-64-95): not an immutable chip, please consider fixing it! <6>[ 3.403425] platform 4830e000.lcdc: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@b000/i2c@0/tda19988@70 <4>[ 3.428616] sdhci-omap 481d8000.mmc: supply pbias not found, using dummy regulator <4>[ 3.442451] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.512496] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 3.536068] random: crng init done <6>[ 3.592607] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.759997] Freeing initrd memory: 16768K <6>[ 3.796138] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.806215] cpsw-switch 4a100000.switch: initialized cpsw ale version 1.4 <6>[ 3.813524] cpsw-switch 4a100000.switch: ALE Table size 1024 <6>[ 3.819792] cpsw-switch 4a100000.switch: cpts: overflow check period 500 (jiffies) <6>[ 3.827913] cpsw-switch 4a100000.switch: CPTS: ref_clk_freq:250000000 calc_mult:2147483648 calc_shift:29 error:0 nsec/sec <6>[ 3.839549] cpsw-switch 4a100000.switch: Detected MACID = 64:cf:d9:3f:a0:d5 <5>[ 3.848472] cpsw-switch 4a100000.switch: initialized (regs 0x4a100000, pool size 256) hw_ver:0019010C 1.12 (0) <3>[ 3.876296] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.884853] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.943763] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <4>[ 3.960577] gpio gpiochip3: (gpio-96-127): not an immutable chip, please consider fixing it! <3>[ 3.974885] l3-aon-clkctrl:0000:0: failed to disable <6>[ 3.984362] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 35, base_baud = 3000000) is a 8250 <6>[ 3.993803] printk: console [ttyS0] enabled <6>[ 3.993803] printk: console [ttyS0] enabled <6>[ 4.002880] printk: bootconsole [omap8250] disabled <6>[ 4.002880] printk: bootconsole [omap8250] disabled <4>[ 4.042730] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.056060] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.072271] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.079566] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 4.087600] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.105519] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.114713] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.119829] sdhci-omap 48060000.mmc: supply pbias not found, using dummy regulator <4>[ 4.136000] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <4>[ 4.144674] sdhci-omap 481d8000.mmc: supply pbias not found, using dummy regulator <4>[ 4.178758] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.252235] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.287182] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <6>[ 4.295999] cpsw-switch 4a100000.switch: starting ndev. mode: dual_mac <6>[ 4.352100] mmc1: new high speed MMC card at address 0001 <6>[ 4.359909] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.370696] mmcblk1: p1 <6>[ 4.376894] mmcblk1boot0: mmc1:0001 M62704 2.00 MiB <6>[ 4.383811] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 4.398056] mmcblk1boot1: mmc1:0001 M62704 2.00 MiB <6>[ 4.413569] mmcblk1rpmb: mmc1:0001 M62704 512 KiB, chardev (236:0) <6>[ 7.552984] cpsw-switch 4a100000.switch eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.561746] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.612075] Sending DHCP requests ., OK <6>[ 7.656421] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.9 <6>[ 7.664608] IP-Config: Complete: <6>[ 7.668135] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.9, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.678753] host=192.168.11.9, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.685828] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.685859] nameserver0=192.168.11.1 <6>[ 7.710752] Freeing unused kernel image (initmem) memory: 2048K <6>[ 7.732868] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.956114] udevd[100]: starting version 3.2.9 <27>[ 7.973040] udevd[100]: specified user 'tss' unknown <27>[ 7.978615] udevd[100]: specified group 'tss' unknown <30>[ 7.994139] udevd[101]: starting eudev-3.2.9 <4>[ 10.504472] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 10.513641] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 10.723579] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 10.732703] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 10.941397] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 10.947272] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 11.183262] hub 1-0:1.0: USB hub found <6>[ 11.220301] hub 1-0:1.0: 1 port detected <6>[ 11.814936] tda998x 0-0070: found TDA19988 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-999445/environment . /lava-999445/environment / # /lava-999445/bin/lava-test-runner /lava-999445/0 /lava-999445/bin/lava-test-runner /lava-999445/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-999445/0/tests/0_dmesg + cat uuid + UUID=999445_1.5.2.4.1 + <8>[ 16.955641] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.016880] <8>[ 17.072889] <8>[ 17.128362] + set +x <8>[ 17.139374] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-999445/environment / # . /lava-999445/environment/lava-999445/bin/lava-test-runner /lava-999445/1 / # /lava-999445/bin/lava-test-runner /lava-999445/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-999445/1/tests/1_bootrr + cat uuid + UUID=999445_1.5.2.4.5 + <8>[ 17.660958] set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-999445/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-999445/1/../bin/lava-test-case <8>[ 17.785682] /lava-999445/1/../bin/lava-test-case <8>[ 17.838206] /lava-999445/1/../bin/lava-test-case <8>[ 17.869936] /lava-999445/1/../bin/lava-test-case <8>[ 17.928522] /lava-999445/1/../bin/lava-test-case <8>[ 17.978187] /lava-999445/1/../bin/lava-test-case <8>[ 18.017727] /lava-999445/1/../bin/lava-test-case <8>[ 18.066871] /lava-999445/1/../bin/lava-test-case <8>[ 18.115572] /lava-999445/1/../bin/lava-test-case <8>[ 18.155232] /lava-999445/1/../bin/lava-test-case <8>[ 18.204195] /lava-999445/1/../bin/lava-test-case <8>[ 19.261385] /lava-999445/1/../bin/lava-test-case <8>[ 20.330402] /lava-999445/1/../bin/lava-test-case <8>[ 20.369409] /lava-999445/1/../bin/lava-test-case <8>[ 20.408067] /lava-999445/1/../bin/lava-test-case <8>[ 20.447934] /lava-999445/1/../bin/lava-test-case <8>[ 20.496307] /lava-999445/1/../bin/lava-test-case <8>[ 20.536681] /lava-999445/1/../bin/lava-test-case <8>[ 20.586006] /lava-999445/1/../bin/lava-test-case <8>[ 20.633975] /lava-999445/1/../bin/lava-test-case <8>[ 20.672918] /lava-999445/1/../bin/lava-test-case <8>[ 20.721532] /lava-999445/1/../bin/lava-test-case <8>[ 20.770397] /lava-999445/1/../bin/lava-test-case <8>[ 20.810908] /lava-999445/1/../bin/lava-test-case <8>[ 20.860282] /lava-999445/1/../bin/lava-test-case <8>[ 20.900412] /lava-999445/1/../bin/lava-test-case <8>[ 20.949799] /lava-999445/1/../bin/lava-test-case <8>[ 20.989650] /lava-999445/1/../bin/lava-test-case <8>[ 21.039250] /lava-999445/1/../bin/lava-test-case <8>[ 21.079811] /lava-999445/1/../bin/lava-test-case <8>[ 21.129303] /lava-999445/1/../bin/lava-test-case <8>[ 21.169735] /lava-999445/1/../bin/lava-test-case <8>[ 21.218571] /lava-999445/1/../bin/lava-test-case <8>[ 22.283378] /lava-999445/1/../bin/lava-test-case <8>[ 23.351269] /lava-999445/1/../bin/lava-test-case <8>[ 23.390694] /lava-999445/1/../bin/lava-test-case <8>[ 23.439910] /lava-999445/1/../bin/lava-test-case <8>[ 24.498908] /lava-999445/1/../bin/lava-test-case <8>[ 25.569672] /lava-999445/1/../bin/lava-test-case <8>[ 26.638604] /lava-999445/1/../bin/lava-test-case <8>[ 27.708655] /lava-999445/1/../bin/lava-test-case <8>[ 28.773128] /lava-999445/1/../bin/lava-test-case <8>[ 29.840238] /lava-999445/1/../bin/lava-test-case <8>[ 30.909547] /lava-999445/1/../bin/lava-test-case <8>[ 31.978882] /lava-999445/1/../bin/lava-test-case <8>[ 32.018468] /lava-999445/1/../bin/lava-test-case <8>[ 32.067089] /lava-999445/1/../bin/lava-test-case <8>[ 32.107083] /lava-999445/1/../bin/lava-test-case <8>[ 32.156169] /lava-999445/1/../bin/lava-test-case <8>[ 32.195959] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-999445/1/../bin/lava-test-case <8>[ 32.237404] /lava-999445/1/../bin/lava-test-case <8>[ 32.286589] /lava-999445/1/../bin/lava-test-case <8>[ 32.332849] + set +x <8>[ 32.348266] / #