Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1051262/tftp-deploy-_qgp31pj/kernel/zImage tftp 0x82000000 1051262/tftp-deploy-_qgp31pj/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1051262/tftp-deploy-_qgp31pj/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 5.3 MiB/s done Bytes transferred = 10519040 (a08200 hex) => tftp 0x83000000 1051262/tftp-deploy-_qgp31pj/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1051262/tftp-deploy-_qgp31pj/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1051262/tftp-deploy-_qgp31pj/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################## 5.1 MiB/s done Bytes transferred = 13242355 (ca0ff3 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1051262/tftp-deploy-_qgp31pj/dtb/am335x-boneblack.dtb tftp 0x88000000 1051262/tftp-deploy-_qgp31pj/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1051262/tftp-deploy-_qgp31pj/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.8 MiB/s done Bytes transferred = 69937 (11131 hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1051262/extract-nfsrootfs-r2z2ruxm,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1051262/extract-nfsrootfs-r2z2ruxm,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-12-04 0:13:41 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13242291 Bytes = 12.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 88014130 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.64-cip10-rt5 (KernelCI@build-j33731-arm-gcc-10-multi-v7-defconfig-sbk8b) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun Dec 3 22:58:49 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/1051262/extract-nfsrootfs-r2z2ruxm,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 412332K/522240K available (14336K kernel code, 2470K rwdata, 6208K rodata, 2048K init, 427K bss, 44372K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000003] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008331] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019101] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033841] Console: colour dummy device 80x30 <3>[ 0.038724] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045783] This ensures that you still see kernel messages. Please <3>[ 0.052509] update your kernel commandline. <6>[ 0.057117] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096103] CPU: Testing write buffer coherency: ok <6>[ 0.101463] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106924] pid_max: default: 32768 minimum: 301 <6>[ 0.112137] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.119957] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.129269] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135820] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.145399] rcu: Hierarchical SRCU implementation. <6>[ 0.145411] rcu: Max phase no-delay instances is 1000. <6>[ 0.145514] printk: bootconsole [omap8250] printing thread started <6>[ 0.168015] EFI services will not be available. <6>[ 0.168273] smp: Bringing up secondary CPUs ... <6>[ 0.168280] smp: Brought up 1 node, 1 CPU <6>[ 0.168289] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.168299] CPU: All CPU(s) started in SVC mode. <6>[ 0.168961] devtmpfs: initialized <6>[ 0.211218] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.211486] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.211513] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.216617] pinctrl core: initialized pinctrl subsystem <6>[ 0.221757] DMI not present or invalid. <6>[ 0.222603] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.225127] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.228391] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.228539] cpuidle: using governor menu <6>[ 0.246444] No ATAGs? <6>[ 0.246463] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.251823] Serial: AMBA PL011 UART driver <6>[ 0.355075] iommu: Default domain type: Translated <6>[ 0.355094] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.355820] SCSI subsystem initialized <6>[ 0.356581] usbcore: registered new interface driver usbfs <6>[ 0.356630] usbcore: registered new interface driver hub <6>[ 0.356679] usbcore: registered new device driver usb <6>[ 0.357645] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.357657] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.357683] PTP clock support registered <6>[ 0.357842] EDAC MC: Ver: 3.0.0 <6>[ 0.372203] vgaarb: loaded <6>[ 0.372799] clocksource: Switched to clocksource dmtimer <6>[ 0.395979] NET: Registered PF_INET protocol family <6>[ 0.396260] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.397354] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.397392] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.397406] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.397449] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 0.397547] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.397655] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.397679] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.397836] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.398701] RPC: Registered named UNIX socket transport module. <6>[ 0.398715] RPC: Registered udp transport module. <6>[ 0.398719] RPC: Registered tcp transport module. <6>[ 0.398723] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.398736] PCI: CLS 0 bytes, default 64 <5>[ 0.400146] Initialise system trusted keyrings <6>[ 0.400810] Trying to unpack rootfs image as initramfs... <6>[ 0.413313] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 0.420035] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.423477] NFS: Registering the id_resolver key type <5>[ 0.423556] Key type id_resolver registered <5>[ 0.423563] Key type id_legacy registered <6>[ 0.423671] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.423681] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.423726] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.439632] Key type asymmetric registered <5>[ 0.439647] Asymmetric key parser 'x509' registered <6>[ 0.439846] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 0.439859] io scheduler mq-deadline registered <6>[ 0.439866] io scheduler kyber registered <6>[ 0.908764] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.921578] SuperH (H)SCI(F) driver initialized <6>[ 0.922211] msm_serial: driver initialized <6>[ 0.922219] STMicroelectronics ASC driver initialized <6>[ 0.923822] STM32 USART driver initialized <6>[ 0.994018] brd: module loaded <6>[ 1.012208] loop: module loaded <6>[ 1.022307] CAN device driver interface <6>[ 1.023181] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.023859] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.023866] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.023959] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.023965] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.026640] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.026707] usbcore: registered new interface driver pegasus <6>[ 1.026763] usbcore: registered new interface driver asix <6>[ 1.026813] usbcore: registered new interface driver ax88179_178a <6>[ 1.026847] usbcore: registered new interface driver cdc_ether <6>[ 1.026891] usbcore: registered new interface driver smsc75xx <6>[ 1.026935] usbcore: registered new interface driver smsc95xx <6>[ 1.026974] usbcore: registered new interface driver net1080 <6>[ 1.027008] usbcore: registered new interface driver cdc_subset <6>[ 1.027045] usbcore: registered new interface driver zaurus <6>[ 1.027118] usbcore: registered new interface driver cdc_ncm <6>[ 1.030275] usbcore: registered new interface driver usb-storage <6>[ 1.034228] i2c_dev: i2c /dev entries driver <5>[ 1.046206] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 1.048075] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.048089] sdhci: Copyright(c) Pierre Ossman <6>[ 1.049450] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.050570] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.134850] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.137622] usbcore: registered new interface driver usbhid <6>[ 1.137640] usbhid: USB HID core driver <6>[ 1.144406] NET: Registered PF_INET6 protocol family <6>[ 1.178078] Segment Routing with IPv6 <6>[ 1.178142] In-situ OAM (IOAM) with IPv6 <6>[ 1.178231] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.179037] NET: Registered PF_PACKET protocol family <6>[ 1.179051] can: controller area network core <6>[ 1.179141] NET: Registered PF_CAN protocol family <6>[ 1.179150] can: raw protocol <6>[ 1.179160] can: broadcast manager protocol <6>[ 1.179177] can: netlink gateway - max_hops=1 <5>[ 1.179826] Key type dns_resolver registered <6>[ 1.180020] ThumbEE CPU extension supported. <5>[ 1.180040] Registering SWP/SWPB emulation handler <3>[ 1.180490] omap_voltage_late_init: Voltage driver support not added <5>[ 1.182502] Loading compiled-in X.509 certificates <6>[ 1.270485] platform 44e10800.pinmux: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@10000/scm@0/pinmux@800/pinmux_clkout2_pin <6>[ 1.271878] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <4>[ 1.287868] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 1.410715] ti-sysc: probe of 48040000.target-module failed with error -16 <4>[ 1.444115] gpio gpiochip0: (gpio-0-31): not an immutable chip, please consider fixing it! <6>[ 1.930910] OMAP GPIO hardware version 0.1 <4>[ 2.014624] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 2.058372] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 2.123994] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 2.205996] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 2.239558] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <4>[ 2.247841] gpio gpiochip1: (gpio-32-63): not an immutable chip, please consider fixing it! <4>[ 2.276430] gpio gpiochip2: (gpio-64-95): not an immutable chip, please consider fixing it! <4>[ 2.308987] sdhci-omap 481d8000.mmc: supply pbias not found, using dummy regulator <4>[ 2.309390] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 2.403832] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 2.421126] random: crng init done <6>[ 2.472949] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.425261] Freeing initrd memory: 12932K <6>[ 3.497961] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.498260] cpsw-switch 4a100000.switch: initialized cpsw ale version 1.4 <6>[ 3.498274] cpsw-switch 4a100000.switch: ALE Table size 1024 <6>[ 3.498392] cpsw-switch 4a100000.switch: cpts: overflow check period 500 (jiffies) <6>[ 3.498407] cpsw-switch 4a100000.switch: CPTS: ref_clk_freq:250000000 calc_mult:2147483648 calc_shift:29 error:0 nsec/sec <6>[ 3.498480] cpsw-switch 4a100000.switch: Detected MACID = 64:cf:d9:3f:a0:d5 <5>[ 3.499942] cpsw-switch 4a100000.switch: initialized (regs 0x4a100000, pool size 256) hw_ver:0019010C 1.12 (0) <3>[ 3.517688] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.517722] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.646512] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <4>[ 3.654913] gpio gpiochip3: (gpio-96-127): not an immutable chip, please consider fixing it! <3>[ 3.660107] l3-aon-clkctrl:0000:0: failed to disable <6>[ 3.687518] printk: console [ttyS0] enabled <6>[ 3.687528] printk: bootconsole [omap8250] disabled <6>[ 3.687566] printk: console [ttyS0] printing thread started <6>[ 3.703272] printk: bootconsole [omap8250] printing thread stopped <4>[ 3.733504] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 3.740863] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 3.763084] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 3.764748] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 3.765070] i2c 0-0070: Fixed dependency cycle(s) with /ocp/interconnect@48000000/segment@300000/target-module@e000/lcdc@0/port/endpoint@0 <6>[ 3.765487] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 3.777537] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 3.777563] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 3.777766] sdhci-omap 48060000.mmc: supply pbias not found, using dummy regulator <4>[ 3.778169] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <4>[ 3.807757] sdhci-omap 481d8000.mmc: supply pbias not found, using dummy regulator <4>[ 3.808170] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.965717] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <6>[ 3.967836] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 3.969289] cpsw-switch 4a100000.switch: starting ndev. mode: dual_mac <6>[ 4.042896] mmc1: new high speed MMC card at address 0001 <6>[ 4.044957] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.049709] mmcblk1: p1 <6>[ 4.051589] mmcblk1boot0: mmc1:0001 M62704 2.00 MiB <6>[ 4.056609] mmcblk1boot1: mmc1:0001 M62704 2.00 MiB <6>[ 4.060545] mmcblk1rpmb: mmc1:0001 M62704 512 KiB, chardev (236:0) <6>[ 4.093391] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.233702] cpsw-switch 4a100000.switch eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.233846] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.282875] Sending DHCP requests ., OK <6>[ 7.322994] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 7.323045] IP-Config: Complete: <6>[ 7.323055] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.323091] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.323109] bootserver=0.0.0.0, rootserver=192.168.11.5, rootpath= <6>[ 7.323130] nameserver0=192.168.11.1 <6>[ 7.336148] Freeing unused kernel image (initmem) memory: 2048K Loading, please wait... <6>[ 7.393954] Run /init as init process Starting version 247.3-7+deb11u2 <4>[ 10.690724] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 10.691041] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 10.760168] tda998x 0-0070: found TDA19988 <4>[ 10.775093] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 10.775405] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 10.998355] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 10.998403] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 11.015264] hub 1-0:1.0: USB hub found <6>[ 11.023041] hub 1-0:1.0: 1 port detected Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 64:cf:d9:3f:a0:d5 mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 192.168.11.255 IP-Config: eth0 complete (dhcp from 192.168.11.1): address: 192.168.11.4 broadcast: 192.168.11.255 netmask: 255.255.255.0 gateway: 192.168.11.1 dns0 : 192.168.11.1 dns1 : 0.0.0.0 domain : usen.ad.jp rootserver: 192.168.11.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 14.994033] systemd[1]: System time before build time, advancing clock. <30>[ 15.134538] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 15.135429] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 15.205737] systemd[1]: Set hostname to . [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0<30>[ 17.034207] systemd[1]: Queued start job for default target Graphical Interface. m. <28>[ 17.036494] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 17.036534] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 17.037863] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[0m. <30>[ 17.083396] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. <30>[ 17.114348] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. <30>[ 17.144350] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. <30>[ 17.173976] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. <30>[ 17.204657] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. <30>[ 17.235075] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 17.235646] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. <30>[ 17.265075] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. <30>[ 17.293355] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. <30>[ 17.323697] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. <30>[ 17.353536] systemd[1]: Reached target Swap. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. <30>[ 17.384416] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/l<30>[ 17.466830] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. og)[0m. <30>[ 17.469483] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. <30>[ 17.493201] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlink Socket[0m. <30>[ 17.526090] systemd[1]: Listening on Network Service Netlink Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0<30>[ 17.557236] systemd[1]: Listening on udev Control Socket. m. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. <30>[ 17.594645] systemd[1]: Listening on udev Kernel Socket. <30>[ 17.625745] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 17.627495] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. Mounting [0;1;39mKernel Debug File System[0m... <30>[ 17.683351] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Trace File System[0m... <30>[ 17.719355] systemd[1]: Mounting Kernel Trace File System... Starting [0;1;39mCreate list of st…odes for the curr<30>[ 17.760662] systemd[1]: Starting Create list of static device nodes for the current kernel... ent kernel[0m... Starting [0;1;39mLoad Kernel Module configfs[0m... <30>[ 17.815053] systemd[1]: Starting Load Kernel Module configfs... <30>[ 17.882629] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module drm[0m... Starting [0;1;39mLoad Kernel Module fuse[0m... <30>[ 17.943441] systemd[1]: Starting Load Kernel Module fuse... <30>[ 17.961624] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. Starting [0;1;39mJournal Service[0m... <30>[ 18.004235] systemd[1]: Starting Journal Service... Starting [0;1;39mLoad Kernel Modules[0m... <30>[ 18.064221] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mRemount Root and Kernel File Systems<30>[ 18.097837] systemd[1]: Starting Remount Root and Kernel File Systems... [0m... Starting [0;1;39mColdplug All udev Devices[0m...<30>[ 18.137940] systemd[1]: Starting Coldplug All udev Devices... [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0<30>[ 18.207390] systemd[1]: Mounted Kernel Debug File System. m. [[0;32m OK [0m] Mounted [0;1;39mKernel Trace File System[0m. <30>[ 18.244395] systemd[1]: Mounted Kernel Trace File System. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. <30>[ 18.275547] systemd[1]: Finished Create list of static device nodes for the current kernel. <30>[ 18.470010] systemd[1]: modprobe@configfs.service: Succeeded. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. <30>[ 18.479468] systemd[1]: Finished Load Kernel Module configfs. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. <30>[ 18.515527] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 18.516948] systemd[1]: Finished Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m.<30>[ 18.555644] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 18.561951] systemd[1]: Finished Load Kernel Module fuse. <30>[ 18.596299] systemd[1]: Finished Load Kernel Modules. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. Mounting [0;1;39mKernel Configuration File System[0m... <30>[ 18.622070] systemd[1]: Finished Remount Root and Kernel File Systems. <30>[ 18.637356] systemd[1]: Condition check resulted in FUSE Control File System being skipped. <30>[ 18.656055] systemd[1]: Mounting Kernel Configuration File System... Starting [0;1;39mLoad/Save Random Seed[0m... Starting [0;1;39mApply Kernel Variables[0m... <30>[ 18.702301] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 18.715410] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <30>[ 18.734082] systemd[1]: Starting Load/Save Random Seed... <30>[ 18.774305] systemd[1]: Starting Apply Kernel Variables... Starting [0;1;39mCreate System Users[0m... [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. <30>[ 18.854134] systemd[1]: Starting Create System Users... <30>[ 18.871026] systemd[1]: Mounted Kernel Configuration File System. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. <30>[ 19.176341] systemd[1]: Finished Load/Save Random Seed. <30>[ 19.194201] systemd[1]: Condition check resulted in First Boot Complete being skipped. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m<30>[ 19.259149] systemd[1]: Finished Apply Kernel Variables. . [[0;32m OK [0m] Started [0;1;39mJournal Service[0m.<30>[ 19.409317] systemd[1]: Started Journal Service. Starting [0;1;39mFlush Journal to Persistent Storage[0m... [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... <46>[ 19.754353] systemd-journald[159]: Received client request to flush runtime journal. [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mNetwork Time Synchronization[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Time Synchronization[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Set[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Synchronized[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0m[0;31m* [0m] (1 of 4) A start job is running for… Login Management (11s / 1min 40s) M[K[[0;1;31m*[0m[0;31m* [0m] (1 of 4) A start job is running for… Login Management (12s / 1min 40s) M[K[[0;31m*[0;1;31m*[0m[0;31m* [0m] (1 of 4) A start job is running for… Login Management (12s / 1min 40s) M[K[[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [K[[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [ [0;31m*[0;1;31m*[0m[0;31m* [0m] (2 of 3) A start job is running for /dev/ttyS0 (15s / 1min 30s) M[K[[0;32m OK [0m] Found device [0;1;39m/dev/ttyS0[0m. [K[[0;32m OK [0m] Reached target [0;1;39mSound Card[0m. [[0;32m OK [0m] Reached target [0;1;39mHardware activated USB gadget[0m. [[0;32m OK [0m] Listening on [0;1;39mLoad/Save RF …itch Status /dev/rfkill Watch[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyS0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. Debian GNU/Linux 11 debian-bullseye-armhf ttyS0 debian-bullseye-armhf log Linux debian-bullseye-armhf 6.1.64-cip10-rt5 #1 SMP Sun Dec 3 22:58:49 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/1051262/extract-nfsrootfs-r2z2ruxm' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/1051262/extract-nfsrootfs-r2z2ruxm' / # export NFS_SERVER_IP='192.168.11.5' export NFS_SERVER_IP='192.168.11.5' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-1051262/environment . /lava-1051262/environment / # /lava-1051262/bin/lava-test-runner /lava-1051262/0 /lava-1051262/bin/lava-test-runner /lava-1051262/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-1051262/0/tests/0_timesync-off ++ cat uuid + UUID=1051262_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-clone3 + TESTRUN_ID=1_kselftest-clone3 + cd /lava-1051262/0/tests/1_kselftest-clone3 ++ cat uuid + UUID=1051262_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c clone3 -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v6.1.64-cip10-rt5/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b beaglebone-black -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-12-04 00:15:22-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v6.1.64-cip10-rt5/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1533744 (1.5M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 49.92K 231KB/s kselftest.tar.xz 14%[=> ] 210.23K 477KB/s kselftest.tar.xz 27%[====> ] 418.35K 638KB/s kselftest.tar.xz 72%[=============> ] 1.06M 1.22MB/s kselftest.tar.xz 100%[===================>] 1.46M 1.47MB/s in 1.0s 2023-12-04 00:15:24 (1.47 MB/s) - 'kselftest.tar.xz' saved [1533744/1533744] skiplist: ======================================== ======================================== clone3:clone3 clone3:clone3_clear_sighand clone3:clone3_set_tid clone3:clone3_cap_checkpoint_restore ============== Tests to run =============== clone3:clone3 clone3:clone3_clear_sighand clone3:clone3_set_tid clone3:clone3_cap_checkpoint_restore ===========End Tests to run =============== shardfile-clone3 pass <12>[ 66.049080] kselftest: Running tests in clone3 TAP version 13 1..4 # selftests: clone3: clone3 # TAP version 13 # 1..17 # # clone3() syscall supported # # [339] Trying clone3() with flags 0 (size 0) # # I am the parent (339). My child's pid is 340 # # [339] clone3() with flags says: 0 expected 0 # ok 1 [339] Result (0) matches expectation (0) # # [339] Trying clone3() with flags 0x20000000 (size 0) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected 0 # not ok 2 [339] Result (-22) is different than expected (0) # # [339] Trying clone3() with flags 0 (size 64) # # I am the parent (339). My child's pid is 341 # # [339] clone3() with flags says: 0 expected 0 # ok 3 [339] Result (0) matches expectation (0) # # [339] Trying clone3() with flags 0 (size 56) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected -22 # ok 4 [339] Result (-22) matches expectation (-22) # # [339] Trying clone3() with flags 0 (size 96) # # I am the parent (339). My child's pid is 342 # # [339] clone3() with flags says: 0 expected 0 # ok 5 [339] Result (0) matches expectation (0) # # [339] Trying clone3() with flags 0 (size 0) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected -22 # ok 6 [339] Result (-22) matches expectation (-22) # # [339] Trying clone3() with flags 0 (size 0) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected -22 # ok 7 [339] Result (-22) matches expectation (-22) # # [339] Trying clone3() with flags 0 (size 0) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected -22 # ok 8 [339] Result (-22) matches expectation (-22) # # [339] Trying clone3() with flags 0 (size 0) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected -22 # ok 9 [339] Result (-22) matches expectation (-22) # # [339] Trying clone3() with flags 0 (size 96) # # I am the parent (339). My child's pid is 343 # # [339] clone3() with flags says: 0 expected 0 # ok 10 [339] Result (0) matches expectation (0) # # [339] Trying clone3() with flags 0 (size 104) # # Argument list too long - Failed to create new process # # [339] clone3() with flags says: -7 expected -7 # ok 11 [339] Result (-7) matches expectation (-7) # # [339] Trying clone3() with flags 0 (size 176) # # Argument list too long - Failed to create new process # # [339] clone3() with flags says: -7 expected -7 # ok 12 [339] Result (-7) matches expectation (-7) # # [339] Trying clone3() with flags 0 (size 4104) # # Argument list too long - Failed to create new process # # [339] clone3() with flags says: -7 expected -7 # ok 13 [339] Result (-7) matches expectation (-7) # # [339] Trying clone3() with flags 0x20000000 (size 64) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected 0 # not ok 14 [339] Result (-22) is different than expected (0) # # [339] Trying clone3() with flags 0x20000000 (size 56) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected -22 # ok 15 [339] Result (-22) matches expectation (-22) # # [339] Trying clone3() with flags 0x20000000 (size 96) # # Invalid argument - Failed to create new process # # [339] clone3() with flags says: -22 expected 0 # not ok 16 [339] Result (-22) is different than expected (0) # # [339] Trying clone3() with flags 0x20000000 (size 4104) # # Argument list too long - Failed to create new process # # [339] clone3() with flags says: -7 expected -7 # ok 17 [339] Result (-7) matches expectation (-7) # # Totals: pass:14 fail:3 xfail:0 xpass:0 skip:0 error:0 not ok 1 selftests: clone3: clone3 # exit=1 # selftests: clone3: clone3_clear_sighand # TAP version 13 # 1..1 # # clone3() syscall supported # Bail out! Failed to clear signal handler for child process # # Planned tests != run tests (1 != 0) # # Totals: pass:0 fail:0 xfail:0 xpass:0 skip:0 error:0 not ok 2 selftests: clone3: clone3_clear_sighand # exit=1 # selftests: clone3: clone3_set_tid # TAP version 13 # 1..29 # # clone3() syscall supported # # /proc/sys/kernel/pid_max 32768 # # [382] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 0 says :-22 - expected -22 # ok 1 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 0 says :-22 - expected -22 # ok 2 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 0 says :-22 - expected -22 # ok 3 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 0 says :-22 - expected -22 # ok 4 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 0 says :-22 - expected -22 # ok 5 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID -1 says :-22 - expected -22 # ok 6 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID -1 says :-22 - expected -22 # ok 7 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID -1 says :-22 - expected -22 # ok 8 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID -1 says :-22 - expected -22 # ok 9 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID -1 says :-22 - expected -22 # ok 10 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 0 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 0 says :-22 - expected -22 # ok 11 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID -1 says :-22 - expected -22 # ok 12 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to -1 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID -1 says :-22 - expected -22 # ok 13 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to -1 and 0x20000000 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID -1 says :-22 - expected -22 # ok 14 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 1 and 0x0 # # File exists - Failed to create new process # # [382] clone3() with CLONE_SET_TID 1 says :-17 - expected -17 # ok 15 [382] Result (-17) matches expectation (-17) # # [382] Trying clone3() with CLONE_SET_TID to 1 and 0x20000000 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 1 says :-22 - expected 0 # not ok 16 [382] Result (-22) is different than expected (0) # # [382] Trying clone3() with CLONE_SET_TID to 32768 and 0x0 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 32768 says :-22 - expected -22 # ok 17 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 32768 and 0x20000000 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 32768 says :-22 - expected -22 # ok 18 [382] Result (-22) matches expectation (-22) # # Child has PID 383 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 32768 says :-22 - expected -22 # ok 18 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 383 and 0x0 # # I am the child, my PID is 383 (expected 383) # # I am the parent (382). My child's pid is 383 # # [382] clone3() with CLONE_SET_TID 383 says :0 - expected 0 # ok 19 [382] Result (0) matches expectation (0) # # [382] Trying clone3() with CLONE_SET_TID to 383 and 0x20000000 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 383 says :-22 - expected -22 # ok 20 [382] Result (-22) matches expectation (-22) # # [382] Trying clone3() with CLONE_SET_TID to 1 and 0x20000000 # # Invalid argument - Failed to create new process # # [382] clone3() with CLONE_SET_TID 1 says :-22 - expected 0 # not ok 21 [382] Result (-22) is different than expected (0) # # unshare PID namespace # Bail out! unshare(CLONE_NEWPID) failed: Invalid argument # # Planned tests != run tests (29 != 21) # # Totals: pass:19 fail:2 xfail:0 xpass:0 skip:0 error:0 not ok 3 selftests: clone3: clone3_set_tid # exit=1 # selftests: clone3: clone3_cap_checkpoint_restore # TAP version 13 # 1..1 # # Starting 1 tests from 1 test cases. # # RUN global.clone3_cap_checkpoint_restore ... # # clone3_cap_checkpoint_restore.c:155:clone3_cap_checkpoint_restore:Child has PID 404 # # clone3() syscall supported # # clone3_cap_checkpoint_restore.c:88:clone3_cap_checkpoint_restore:[403] Trying clone3() with CLONE_SET_TID to 404 # # clone3() syscall supported # # clone3_cap_checkpoint_restore.c:55:clone3_cap_checkpoint_restore:Operation not permitted - Failed to create new process # # clone3_cap_checkpoint_restore.c:90:clone3_cap_checkpoint_restore:[403] clone3() with CLONE_SET_TID 404 says:-1 # # clone3_cap_checkpoint_restore.c:88:clone3_cap_checkpoint_restore:[403] Trying clone3() with CLONE_SET_TID to 404 # # clone3_cap_checkpoint_restore.c:70:clone3_cap_checkpoint_restore:I am the parent (403). My child's pid is 404 # # clone3_cap_checkpoint_restore.c:63:clone3_cap_checkpoint_restore:I am the child, my PID is 404 (expected 404) # # clone3_cap_checkpoint_restore.c:90:clone3_cap_checkpoint_restore:[403] clone3() with CLONE_SET_TID 404 says:0 # # OK global.clone3_cap_checkpoint_restore # ok 1 global.clone3_cap_checkpoint_restore # # PASSED: 1 / 1 tests passed. # # Totals: pass:1 fail:0 xfail:0 xpass:0 skip:0 error:0 ok 4 selftests: clone3: clone3_cap_checkpoint_restore clone3_clone3_Result_0_matches_expectation_0 pass clone3_clone3_Result_22_is_different_than_expected_0 fail clone3_clone3_Result_0_matches_expectation_0 pass clone3_clone3_Result_22_matches_expectation_22 pass clone3_clone3_Result_0_matches_expectation_0 pass clone3_clone3_Result_22_matches_expectation_22 pass clone3_clone3_Result_22_matches_expectation_22 pass clone3_clone3_Result_22_matches_expectation_22 pass clone3_clone3_Result_22_matches_expectation_22 pass clone3_clone3_Result_0_matches_expectation_0 pass clone3_clone3_Result_7_matches_expectation_7 pass clone3_clone3_Result_7_matches_expectation_7 pass clone3_clone3_Result_7_matches_expectation_7 pass clone3_clone3_Result_22_is_different_than_expected_0 fail clone3_clone3_Result_22_matches_expectation_22 pass clone3_clone3_Result_22_is_different_than_expected_0 fail clone3_clone3_Result_7_matches_expectation_7 pass clone3_clone3 fail clone3_clone3_clear_sighand fail clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_17_matches_expectation_17 pass clone3_clone3_set_tid_Result_22_is_different_than_expected_0 fail clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_0_matches_expectation_0 pass clone3_clone3_set_tid_Result_22_matches_expectation_22 pass clone3_clone3_set_tid_Result_22_is_different_than_expected_0 fail clone3_clone3_set_tid fail clone3_clone3_cap_checkpoint_restore_global_clone3_cap_checkpoint_restore pass clone3_clone3_cap_checkpoint_restore pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #