[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (12 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12172596/tftp-deploy-1imv36m5/kernel/zImage tftp 0x10000000 12172596/tftp-deploy-1imv36m5/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12172596/tftp-deploy-1imv36m5/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 13.5 MiB/s done Bytes transferred = 10519040 (a08200 hex) => tftp 0x14000000 12172596/tftp-deploy-1imv36m5/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12172596/tftp-deploy-1imv36m5/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12172596/tftp-deploy-1imv36m5/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 14.1 MiB/s done Bytes transferred = 13239698 (ca0592 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12172596/tftp-deploy-1imv36m5/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12172596/tftp-deploy-1imv36m5/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12172596/tftp-deploy-1imv36m5/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 8.1 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12172596/extract-nfsrootfs-br7q4qv0,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12172596/extract-nfsrootfs-br7q4qv0,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xa08200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13239634 Bytes = 12.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.64-cip10-rt5 (KernelCI@build-j33731-arm-gcc-10-multi-v7-defconfig-sbk8b) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun Dec 3 22:58:49 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12172596/extract-nfsrootfs-br7q4qv0,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 934220K/1048576K available (14336K kernel code, 2470K rwdata, 6208K rodata, 2048K init, 427K bss, 48820K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008439] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022725] Console: colour dummy device 80x30 <6>[ 0.024634] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.035032] CPU: Testing write buffer coherency: ok <6>[ 0.040164] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.045461] pid_max: default: 32768 minimum: 301 <6>[ 0.050510] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057925] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066824] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072714] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080420] rcu: Hierarchical SRCU implementation. <6>[ 0.080426] rcu: Max phase no-delay instances is 1000. <6>[ 0.080517] printk: bootconsole [ec_imx21] printing thread started <6>[ 0.099266] EFI services will not be available. <6>[ 0.099646] smp: Bringing up secondary CPUs ... <6>[ 0.100477] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.100494] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.101418] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.101433] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.102333] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.102348] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.102449] smp: Brought up 1 node, 4 CPUs <6>[ 0.102460] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.102468] CPU: All CPU(s) started in SVC mode. <6>[ 0.103043] devtmpfs: initialized <6>[ 0.111565] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.111870] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.111891] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.115210] pinctrl core: initialized pinctrl subsystem <6>[ 0.119042] DMI not present or invalid. <6>[ 0.119903] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.213976] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.216684] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.216746] cpuidle: using governor menu <6>[ 0.217022] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.224599] platform soc: Fixed dependency cycle(s) with /soc/bus@2000000/gpc@20dc000 <6>[ 0.241325] platform 20e0000.pinctrl: Fixed dependency cycle(s) with /soc/bus@2000000/pinctrl@20e0000/imx6q-sabrelite/hoggrp <6>[ 0.246859] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu2_csi1_mux/port@0/endpoint <6>[ 0.246912] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux/port@0/endpoint <6>[ 0.247815] platform 2400000.ipu: Fixed dependency cycle(s) with /ldb/lvds-channel@0/port@1/endpoint <6>[ 0.247850] platform 2400000.ipu: Fixed dependency cycle(s) with /soc/hdmi@120000/ports/port@1/endpoint <6>[ 0.247885] platform 2400000.ipu: Fixed dependency cycle(s) with /ldb/lvds-channel@0/port@0/endpoint <6>[ 0.247915] platform 2400000.ipu: Fixed dependency cycle(s) with /soc/hdmi@120000/ports/port@0/endpoint <6>[ 0.247970] platform 2400000.ipu: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000/port@2/endpoint <6>[ 0.248017] platform 2400000.ipu: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux/port@2/endpoint <6>[ 0.249382] platform 2800000.ipu: Fixed dependency cycle(s) with /ldb/lvds-channel@0/port@3/endpoint <6>[ 0.249513] platform 2800000.ipu: Fixed dependency cycle(s) with /soc/hdmi@120000/ports/port@3/endpoint <6>[ 0.249636] platform 2800000.ipu: Fixed dependency cycle(s) with /ldb/lvds-channel@0/port@2/endpoint <6>[ 0.249760] platform 2800000.ipu: Fixed dependency cycle(s) with /soc/hdmi@120000/ports/port@2/endpoint <6>[ 0.249857] platform 2800000.ipu: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu2_csi1_mux/port@2/endpoint <6>[ 0.249958] platform 2800000.ipu: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000/port@3/endpoint <6>[ 0.256777] platform disp0: Fixed dependency cycle(s) with /soc/ipu@2400000/port@2/endpoint@0 <6>[ 0.257601] platform panel-lcd: Fixed dependency cycle(s) with /disp0/port@1/endpoint <6>[ 0.259123] platform panel-lvds0: Fixed dependency cycle(s) with /ldb/lvds-channel@0/port@4/endpoint <6>[ 0.260475] No ATAGs? <6>[ 0.434901] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.434912] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.438247] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.447034] Serial: AMBA PL011 UART driver <6>[ 0.453125] printk: console [ramoops-1] enabled <6>[ 0.453149] printk: console [ramoops-1] printing thread started <6>[ 0.453922] pstore: Registered ramoops as persistent store backend <6>[ 0.453928] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.515457] iommu: Default domain type: Translated <6>[ 0.515468] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.516282] SCSI subsystem initialized <6>[ 0.516772] usbcore: registered new interface driver usbfs <6>[ 0.516818] usbcore: registered new interface driver hub <6>[ 0.516865] usbcore: registered new device driver usb <4>[ 0.517096] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.517229] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.517377] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.517517] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.519486] i2c i2c-0: IMX I2C adapter registered <6>[ 0.521231] i2c 1-0040: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000/port@0/endpoint <6>[ 0.521793] i2c i2c-1: IMX I2C adapter registered <6>[ 0.522674] i2c i2c-2: IMX I2C adapter registered <6>[ 0.524115] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.524121] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.524140] PTP clock support registered <6>[ 0.524391] EDAC MC: Ver: 3.0.0 <6>[ 0.527950] vgaarb: loaded <6>[ 0.633265] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.643268] NET: Registered PF_INET protocol family <6>[ 0.643684] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.645541] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.645570] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.645586] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.645671] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.645951] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.646142] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.646188] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.646389] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.646970] RPC: Registered named UNIX socket transport module. <6>[ 0.646978] RPC: Registered udp transport module. <6>[ 0.646982] RPC: Registered tcp transport module. <6>[ 0.646986] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.646996] PCI: CLS 0 bytes, default 64 <4>[ 0.647595] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 0.648072] Trying to unpack rootfs image as initramfs... <6>[ 0.769297] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 0.771380] Initialise system trusted keyrings <6>[ 0.771721] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.777745] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.778508] NFS: Registering the id_resolver key type <5>[ 0.778547] Key type id_resolver registered <5>[ 0.778552] Key type id_legacy registered <6>[ 0.778652] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.778661] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.778697] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.779182] Key type asymmetric registered <5>[ 0.779191] Asymmetric key parser 'x509' registered <6>[ 0.779349] bounce: pool size: 64 pages <6>[ 0.779462] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.779471] io scheduler mq-deadline registered <6>[ 0.779477] io scheduler kyber registered <6>[ 0.926270] mxs-dma 110000.dma-apbh: initialized <6>[ 1.011210] printk: console [ttymxc1] enabled <6>[ 1.011210] printk: console [ttymxc1] printing thread started <6>[ 1.011219] printk: bootconsole [ec_imx21] disabled <6>[ 1.027079] printk: bootconsole [ec_imx21] printing thread stopped <6>[ 1.028717] msm_serial: driver initialized <6>[ 1.028725] STMicroelectronics ASC driver initialized <6>[ 1.030526] STM32 USART driver initialized <6>[ 1.062836] brd: module loaded <6>[ 1.070449] loop: module loaded <6>[ 1.074661] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.074678] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.074687] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.074695] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 1.074779] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 1.074959] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 1.075022] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 1.077940] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.077971] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.077987] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.159790] scsi host0: ahci-imx <6>[ 1.160156] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 <6>[ 1.173863] CAN device driver interface <6>[ 1.175713] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.179630] pps pps0: new PPS source ptp0 <3>[ 1.202849] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address <6>[ 1.202867] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 <6>[ 1.202965] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 <6>[ 1.203051] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 <6>[ 1.203133] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 <6>[ 1.203289] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 <6>[ 1.203377] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 <6>[ 1.203460] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 <6>[ 1.203540] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 7 <6>[ 1.514794] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 1.514868] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 1.514877] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 1.708064] Freeing initrd memory: 12932K <4>[ 1.708775] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.708813] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 1.728329] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.729821] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.729826] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.729890] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.729894] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.736811] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.736858] usbcore: registered new interface driver pegasus <6>[ 1.736909] usbcore: registered new interface driver asix <6>[ 1.736943] usbcore: registered new interface driver ax88179_178a <6>[ 1.736976] usbcore: registered new interface driver cdc_ether <6>[ 1.737022] usbcore: registered new interface driver smsc75xx <6>[ 1.737076] usbcore: registered new interface driver smsc95xx <6>[ 1.737112] usbcore: registered new interface driver net1080 <6>[ 1.737146] usbcore: registered new interface driver cdc_subset <6>[ 1.737176] usbcore: registered new interface driver zaurus <6>[ 1.737241] usbcore: registered new interface driver cdc_ncm <6>[ 1.744164] usbcore: registered new interface driver usb-storage <6>[ 1.752846] i2c_dev: i2c /dev entries driver <6>[ 1.776966] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.776974] sdhci: Copyright(c) Pierre Ossman <6>[ 1.779989] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.782600] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.784077] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 1.784119] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 1.788504] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 1.882107] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.884807] usbcore: registered new interface driver usbhid <6>[ 1.884817] usbhid: USB HID core driver <6>[ 1.895114] NET: Registered PF_INET6 protocol family <6>[ 1.896528] Segment Routing with IPv6 <6>[ 1.896586] In-situ OAM (IOAM) with IPv6 <6>[ 1.896668] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.897306] NET: Registered PF_PACKET protocol family <6>[ 1.897314] can: controller area network core <6>[ 1.897387] NET: Registered PF_CAN protocol family <6>[ 1.897395] can: raw protocol <6>[ 1.897402] can: broadcast manager protocol <6>[ 1.897413] can: netlink gateway - max_hops=1 <5>[ 1.897737] Key type dns_resolver registered <6>[ 1.901535] ThumbEE CPU extension supported. <5>[ 1.901550] Registering SWP/SWPB emulation handler <5>[ 1.902266] Loading compiled-in X.509 certificates <6>[ 1.913739] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 1.913760] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 1.915064] pstore: Using crash dump compression: deflate <4>[ 1.989312] imx_usb 2184200.usb: No over current polarity defined <6>[ 1.993191] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 1.993224] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.033075] mmc2: new high speed SDHC card at address 0001 <6>[ 2.033295] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.034921] hub 1-0:1.0: USB hub found <6>[ 2.035013] hub 1-0:1.0: 1 port detected <6>[ 2.035084] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 2.040284] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.057403] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 2.118810] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.118824] GPT:29296874 != 30965759 <4>[ 2.118838] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.118844] GPT:29296874 != 30965759 <4>[ 2.118854] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.119035] mmcblk2: p1 p2 p3 <6>[ 2.135008] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 2.323226] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.524942] hub 1-1:1.0: USB hub found <6>[ 2.525147] hub 1-1:1.0: 3 ports detected <6>[ 5.293623] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 5.293673] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.343185] Sending DHCP requests ., OK <6>[ 5.393315] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 5.393340] IP-Config: Complete: <6>[ 5.393345] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.393371] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 5.393384] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.393399] nameserver0=192.168.201.1 <6>[ 5.402215] Freeing unused kernel image (initmem) memory: 2048K <6>[ 5.504171] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 6.632245] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 6.635756] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 6.691231] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.694421] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.704115] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.704256] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.705062] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 6.729624] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 6.729706] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.729722] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.730279] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 6.890243] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 6.912024] caam 2100000.crypto: Entropy delay = 3200 <6>[ 6.972829] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 7.010031] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.014501] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.033587] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.033616] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.033631] caam 2100000.crypto: job rings = 2, qi = 0 <3>[ 7.128323] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' <6>[ 7.539277] caam algorithms registered in /proc/crypto <6>[ 7.541118] caam 2100000.crypto: registering rng-caam <6>[ 7.541535] caam 2100000.crypto: rng crypto API alg registered prng-caam Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.<5>[ 7.723564] random: crng init done 1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 8.393308] systemd[1]: System time before build time, advancing clock. <30>[ 8.438315] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 8.439054] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 8.506003] systemd[1]: Set hostname to . <30>[ 9.401704] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 9.403624] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 9.403646] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 9.404399] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 9.474683] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 9.504708] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. <30>[ 9.534383] systemd[1]: Created slice User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 9.564067] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 9.593950] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. <30>[ 9.623552] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 9.623816] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. <30>[ 9.653668] systemd[1]: Reached target Paths. [ OK ] Reached target Remote File Systems. <30>[ 9.683400] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. <30>[ 9.713615] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. <30>[ 9.743761] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 9.774538] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/l<30>[ 9.838322] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. og). <30>[ 9.839824] systemd[1]: Listening on Journal Socket (/dev/log). <30>[ 9.863007] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 9.894521] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. <30>[ 9.925499] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 9.954669] systemd[1]: Listening on udev Kernel Socket. <30>[ 9.983877] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 9.984358] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. Mounting Kernel<30>[ 10.033645] systemd[1]: Mounting Kernel Debug File System... Debug File System... Mounting Kernel<30>[ 10.079444] systemd[1]: Mounting Kernel Trace File System... Trace File System... Starting Create list of st…odes for the curr<30>[ 10.119166] systemd[1]: Starting Create list of static device nodes for the current kernel... ent kernel... Starting Load Kernel Module configfs... <30>[ 10.169052] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module drm... <30>[ 10.207393] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... <30>[ 10.237399] systemd[1]: Starting Load Kernel Module fuse... Starting Journa<30>[ 10.266843] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. l Service... <30>[ 10.271010] systemd[1]: Starting Journal Service... Starting Load Kernel Modules... <30>[ 10.299627] systemd[1]: Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems<30>[ 10.329285] systemd[1]: Starting Remount Root and Kernel File Systems... [0m... Starting Coldplug All udev Devices... <30>[ 10.367398] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted [0;1<30>[ 10.401034] systemd[1]: Mounted Kernel Debug File System. ;39mKernel Debug File System. [ OK ] Mounted Kernel Trace File System. <30>[ 10.434137] systemd[1]: Mounted Kernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 10.474689] systemd[1]: Finished Create list of static device nodes for the current kernel. <30>[ 10.522940] systemd[1]: modprobe@configfs.service: Succeeded. [ OK ] Finished Load Kernel Module configf<30>[ 10.523966] systemd[1]: Finished Load Kernel Module configfs. s. [ OK ] Started Journal Service. <30>[ 10.573983] systemd[1]: Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 10.905370] systemd-journald[238]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [* ] A start job is running for User Login Management (7s / 1min 34s) M [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Sound Card. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 6.1.64-cip10-rt5 #1 SMP Sun Dec 3 22:58:49 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12172596/extract-nfsrootfs-br7q4qv0' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12172596/extract-nfsrootfs-br7q4qv0' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12172596/environment . /lava-12172596/environment / # /lava-12172596/bin/lava-test-runner /lava-12172596/0 /lava-12172596/bin/lava-test-runner /lava-12172596/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12172596/0/tests/0_timesync-off ++ cat uuid + UUID=12172596_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-12172596/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=12172596_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v6.1.64-cip10-rt5/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-12-03 23:12:25-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v6.1.64-cip10-rt5/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1533744 (1.5M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 1%[ ] 17.63K 67.1KB/s kselftest.tar.xz 4%[ ] 64.29K 112KB/s kselftest.tar.xz 5%[> ] 84.57K 107KB/s kselftest.tar.xz 7%[> ] 111.44K 105KB/s kselftest.tar.xz 9%[> ] 140.65K 106KB/s kselftest.tar.xz 10%[=> ] 159.52K 104KB/s kselftest.tar.xz 12%[=> ] 184.97K 105KB/s kselftest.tar.xz 14%[=> ] 209.94K 106KB/s kselftest.tar.xz 15%[==> ] 234.46K 107KB/s kselftest.tar.xz 17%[==> ] 265.57K 109KB/s kselftest.tar.xz 19%[==> ] 291.03K 110KB/s kselftest.tar.xz 21%[===> ] 327.79K 115KB/s kselftest.tar.xz 24%[===> ] 365.97K 119KB/s eta 10s kselftest.tar.xz 26%[====> ] 394.25K 119KB/s eta 10s kselftest.tar.xz 29%[====> ] 436.67K 124KB/s eta 10s kselftest.tar.xz 32%[=====> ] 483.34K 129KB/s eta 10s kselftest.tar.xz 34%[=====> ] 514.45K 130KB/s eta 10s kselftest.tar.xz 37%[======> ] 563.94K 138KB/s eta 7s kselftest.tar.xz 41%[=======> ] 617.67K 147KB/s eta 7s kselftest.tar.xz 43%[=======> ] 644.06K 145KB/s eta 7s kselftest.tar.xz 46%[========> ] 700.62K 154KB/s eta 7s kselftest.tar.xz 49%[========> ] 737.87K 158KB/s eta 7s kselftest.tar.xz 52%[=========> ] 784.53K 164KB/s eta 5s kselftest.tar.xz 54%[=========> ] 821.30K 170KB/s eta 5s kselftest.tar.xz 58%[==========> ] 870.79K 176KB/s eta 5s kselftest.tar.xz 60%[===========> ] 907.56K 179KB/s eta 5s kselftest.tar.xz 62%[===========> ] 935.84K 177KB/s eta 5s kselftest.tar.xz 65%[============> ] 979.67K 183KB/s eta 3s kselftest.tar.xz 67%[============> ] 1016K 181KB/s eta 3s kselftest.tar.xz 70%[=============> ] 1.03M 182KB/s eta 3s kselftest.tar.xz 73%[=============> ] 1.07M 186KB/s eta 3s kselftest.tar.xz 76%[==============> ] 1.11M 186KB/s eta 3s kselftest.tar.xz 79%[==============> ] 1.16M 188KB/s eta 2s kselftest.tar.xz 82%[===============> ] 1.21M 188KB/s eta 2s kselftest.tar.xz 85%[================> ] 1.25M 190KB/s eta 2s kselftest.tar.xz 89%[================> ] 1.31M 197KB/s eta 2s kselftest.tar.xz 93%[=================> ] 1.36M 197KB/s eta 2s kselftest.tar.xz 96%[==================> ] 1.42M 202KB/s eta 0s kselftest.tar.xz 99%[==================> ] 1.46M 197KB/s eta 0s kselftest.tar.xz 100%[===================>] 1.46M 199KB/s in 8.9s 2023-12-03 23:12:35 (168 KB/s) - 'kselftest.tar.xz' saved [1533744/1533744] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== shardfile-filesystems pass <12>[ 41.796679] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #