Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.91 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 410132/tftp-deploy-eqgj1pgf/kernel/Image tftp 0x82000000 410132/tftp-deploy-eqgj1pgf/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '410132/tftp-deploy-eqgj1pgf/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################### 14.7 MiB/s done Bytes transferred = 37835264 (2415200 hex) => tftp 0x90080000 410132/tftp-deploy-eqgj1pgf/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 410132/tftp-deploy-eqgj1pgf/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '410132/tftp-deploy-eqgj1pgf/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 14.1 MiB/s done Bytes transferred = 22182150 (1527906 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 410132/tftp-deploy-eqgj1pgf/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 410132/tftp-deploy-eqgj1pgf/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '410132/tftp-deploy-eqgj1pgf/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 6.9 MiB/s done Bytes transferred = 28772 (7064 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2023-12-27 23:19:36 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 22182086 Bytes = 21.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a063 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.67-cip12-rt7 (KernelCI@build-j60073-arm64-gcc-10-defconfig-kcqm7) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Wed Dec 27 23:03:09 UTC 2023 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7f6a00-0x20ff7f8fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 20 pages/cpu s44840 r8192 d28888 u81920 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3888224K/4126720K available (16192K kernel code, 3732K rwdata, 9328K rodata, 7552K init, 609K bss, 205728K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008839] Console: colour dummy device 80x25 <6>[ 0.013628] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024348] pid_max: default: 32768 minimum: 301 <6>[ 0.029301] LSM: Security Framework initializing <6>[ 0.034281] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.042028] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051050] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.058622] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.065079] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.072641] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.079195] rcu: Hierarchical SRCU implementation. <6>[ 0.079197] rcu: Max phase no-delay instances is 1000. <6>[ 0.079234] printk: bootconsole [ns16550a0] printing thread started <6>[ 0.096550] Platform MSI: gic-its@6020000 domain created <6>[ 0.096625] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.096669] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.097430] EFI services will not be available. <6>[ 0.097522] smp: Bringing up secondary CPUs ... <6>[ 0.097785] Detected PIPT I-cache on CPU1 <6>[ 0.097837] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.097846] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.097870] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.152225] smp: Brought up 1 node, 2 CPUs <6>[ 0.152230] SMP: Total of 2 processors activated. <6>[ 0.152233] CPU features: detected: 32-bit EL0 Support <6>[ 0.152234] CPU features: detected: 32-bit EL1 Support <6>[ 0.152237] CPU features: detected: CRC32 instructions <6>[ 0.152275] CPU: All CPU(s) started at EL2 <6>[ 0.152286] alternatives: applying system-wide alternatives <6>[ 0.153283] devtmpfs: initialized <6>[ 0.156664] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.156674] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.157269] pinctrl core: initialized pinctrl subsystem <6>[ 0.157670] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.157673] SoC family: QorIQ LS1028A <6>[ 0.157674] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.158020] DMI not present or invalid. <6>[ 0.158416] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.158974] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.159085] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.159235] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.159263] audit: initializing netlink subsys (disabled) <6>[ 0.159877] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.159880] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.159915] cpuidle: using governor menu <6>[ 0.160028] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <5>[ 0.160042] audit: type=2000 audit(0.124:1): state=initialized audit_enabled=0 res=1 <6>[ 0.160064] ASID allocator initialised with 65536 entries <6>[ 0.160916] Serial: AMBA PL011 UART driver <4>[ 0.170878] KASLR disabled due to lack of seed <6>[ 0.175765] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.175769] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.175772] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.175774] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.175777] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.175779] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.175781] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.175783] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.184095] ACPI: Interpreter disabled. <6>[ 0.185360] iommu: Default domain type: Translated <6>[ 0.185363] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.185501] SCSI subsystem initialized <6>[ 0.185687] usbcore: registered new interface driver usbfs <6>[ 0.185705] usbcore: registered new interface driver hub <6>[ 0.185718] usbcore: registered new device driver usb <6>[ 0.186008] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.186255] i2c i2c-0: IMX I2C adapter registered <6>[ 0.186483] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.186574] i2c i2c-1: IMX I2C adapter registered <6>[ 0.186659] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.186817] i2c i2c-2: IMX I2C adapter registered <6>[ 0.187264] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.187266] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.187273] PTP clock support registered <6>[ 0.187340] EDAC MC: Ver: 3.0.0 <6>[ 0.188225] FPGA manager framework <6>[ 0.188270] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.188664] vgaarb: loaded <6>[ 0.188848] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.188967] VFS: Disk quotas dquot_6.6.0 <6>[ 0.188990] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.189083] pnp: PnP ACPI: disabled <6>[ 0.192509] NET: Registered PF_INET protocol family <6>[ 0.192750] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.194818] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.194848] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.194857] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.194947] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.195607] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.195693] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.195724] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.195842] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.196198] RPC: Registered named UNIX socket transport module. <6>[ 0.196202] RPC: Registered udp transport module. <6>[ 0.196203] RPC: Registered tcp transport module. <6>[ 0.196205] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.196212] PCI: CLS 0 bytes, default 64 <6>[ 0.196384] Unpacking initramfs... <6>[ 0.201129] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 0.201372] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.202320] kvm [1]: GICv3: no GICV resource entry <6>[ 0.202323] kvm [1]: disabling GICv2 emulation <6>[ 0.202335] kvm [1]: GIC system register CPU interface enabled <6>[ 0.202377] kvm [1]: vgic interrupt IRQ9 <6>[ 0.202408] kvm [1]: Hyp mode initialized successfully <5>[ 0.203034] Initialise system trusted keyrings <6>[ 0.212898] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.216540] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.225100] NFS: Registering the id_resolver key type <5>[ 0.225120] Key type id_resolver registered <5>[ 0.225122] Key type id_legacy registered <6>[ 0.225164] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.225167] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.225282] 9p: Installing v9fs 9p2000 file system support <5>[ 0.279021] Key type asymmetric registered <5>[ 0.279027] Asymmetric key parser 'x509' registered <6>[ 0.279086] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.279090] io scheduler mq-deadline registered <6>[ 0.279093] io scheduler kyber registered <6>[ 0.295410] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.295437] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.295454] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.295467] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.295480] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.295492] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.295504] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.295512] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.295560] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.295627] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.295631] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.295635] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.295638] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.295642] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.295645] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.295648] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.295651] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.295654] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.295672] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 0.295704] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.295710] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.295716] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.295721] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.295740] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 0.295750] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 0.295755] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 0.295892] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 0.295917] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.295923] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.295928] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.295933] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.295950] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 0.295959] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 0.295963] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 0.296093] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 0.296121] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.296128] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.296144] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 0.296270] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 0.296299] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.296304] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.296320] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 0.296423] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 0.296447] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.296452] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.296468] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 0.296599] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 0.296624] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.296629] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.296635] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.296650] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 0.296781] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 0.296805] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.296811] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.296828] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 0.297731] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 0.297774] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 0.297917] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 0.298019] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 0.304887] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 0.305508] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 0.305532] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 0.305545] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 0.305594] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 0.305598] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 0.959051] Freeing initrd memory: 21656K <3>[ 1.304898] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 1.305014] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 1.305019] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 1.305025] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 1.305030] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.305056] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.305123] pci 0001:00:00.0: supports D1 D2 <6>[ 1.305126] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.306073] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.306087] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 1.306228] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 1.306251] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 1.306263] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 1.306309] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 1.306312] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 2.306411] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 2.306467] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 2.306471] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 2.306476] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 2.306481] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.306498] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.354633] printk: c[ 2.30655<6>[ 2.354641] printk: console [ttyS0] enabled 5] pci 0002:00:00.0: supports D1 D2 <6>[ 2.354645] printk: bootconsole [ns16550a0] disabled <6>[ 2.306557] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.381066] printk: bootconsole [ns16550a0] printing thread stopped <6>[ 2.381423] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 2.381786] SuperH (H)SCI(F) driver initialized <6>[ 2.382090] msm_serial: driver initialized <6>[ 2.382487] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 2.384595] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 2.384600] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 2.384604] arm-smmu 5000000.iommu: stage 1 translation <5>[ 2.384606] arm-smmu 5000000.iommu: stage 2 translation <5>[ 2.384609] arm-smmu 5000000.iommu: nested translation <5>[ 2.384613] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 2.384617] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 2.384623] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 2.384626] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 2.384630] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 2.384866] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 2.394098] loop: module loaded <4>[ 2.399552] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 2.419701] megasas: 07.719.03.00-rc1 <6>[ 2.436574] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 2.475406] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 2.503534] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 2.503544] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 2.503548] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 2.504177] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 2.504718] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 2.505246] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 2.505773] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 2.508446] tun: Universal TUN/TAP device driver, 1.6 <6>[ 2.509032] thunder_xcv, ver 1.0 <6>[ 2.509055] thunder_bgx, ver 1.0 <6>[ 2.509078] nicpf, ver 1.0 <6>[ 2.509638] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 2.509848] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 2.616854] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.617774] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.617855] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 2.724855] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.725192] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.725264] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 2.832854] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.833194] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.833525] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 2.940856] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 2.955119] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 2.955215] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 2.955333] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 2.955445] pps pps0: new PPS source ptp0 <6>[ 2.955922] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 2.955926] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 2.955963] hclge is initializing <6>[ 2.955972] e1000: Intel(R) PRO/1000 Network Driver <6>[ 2.955974] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 2.955999] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.956001] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.956029] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.956031] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.956052] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.956053] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.956275] sky2: driver version 1.30 <6>[ 2.957055] VFIO - User Level meta-driver version: 0.3 <6>[ 2.957422] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 2.957864] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 3.018961] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.018974] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 3.019105] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.019120] xhci-hcd xhci-hcd.0.auto: irq 99, io mem 0x03100000 <6>[ 3.019212] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.019218] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 3.019224] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.019544] hub 1-0:1.0: USB hub found <6>[ 3.019558] hub 1-0:1.0: 1 port detected <6>[ 3.019724] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.019956] hub 2-0:1.0: USB hub found <6>[ 3.019972] hub 2-0:1.0: 1 port detected <6>[ 3.020167] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.020175] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 3.020285] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.020311] xhci-hcd xhci-hcd.1.auto: irq 100, io mem 0x03110000 <6>[ 3.020402] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.020410] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 3.020417] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.020664] hub 3-0:1.0: USB hub found <6>[ 3.020678] hub 3-0:1.0: 1 port detected <6>[ 3.020829] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.021096] hub 4-0:1.0: USB hub found <6>[ 3.021109] hub 4-0:1.0: 1 port detected <6>[ 3.021635] usbcore: registered new interface driver usb-storage <6>[ 3.023531] i2c_dev: i2c /dev entries driver <6>[ 3.026912] sp805-wdt c000000.watchdog: registration successful <6>[ 3.027035] sp805-wdt c010000.watchdog: registration successful <6>[ 3.028606] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 3.029323] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.029327] sdhci: Copyright(c) Pierre Ossman <6>[ 3.029813] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.030461] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.031801] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 3.031931] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 3.035393] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.036984] usbcore: registered new interface driver usbhid <6>[ 3.036989] usbhid: USB HID core driver <6>[ 3.041415] NET: Registered PF_PACKET protocol family <6>[ 3.041504] 9pnet: Installing 9P2000 support <5>[ 3.041534] Key type dns_resolver registered <6>[ 3.041779] registered taskstats version 1 <5>[ 3.041794] Loading compiled-in X.509 certificates <6>[ 3.048821] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 3.049889] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 3.050041] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 3.050291] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 3.050433] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 3.050580] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 3.050712] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 3.064930] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 3.073943] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 3.160861] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 3.161782] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using ae:93:fe:b2:f5:3d <6>[ 3.161791] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using be:8c:77:2e:ca:6e <6>[ 3.242519] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 3.286027] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 3.309754] mmc0: new HS400 MMC card at address 0001 <6>[ 3.310134] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 3.311284] mmcblk0: p1 p2 <6>[ 3.311696] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 3.312648] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 3.313469] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 3.318346] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 3.329035] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 3.532618] hub 3-1:1.0: USB hub found <6>[ 3.532684] hub 3-1:1.0: 7 ports detected <6>[ 6.401823] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 6.432877] Sending DHCP requests ., OK <6>[ 6.448926] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.91 <6>[ 6.448950] IP-Config: Complete: <6>[ 6.448955] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.91, mask=255.255.255.0, gw=172.16.0.254 <6>[ 6.448977] host=172.16.0.91, domain=lava.lan, nis-domain=(none) <6>[ 6.448987] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 6.449000] nameserver0=8.8.8.8 <6>[ 6.449528] ALSA device list: <6>[ 6.449545] No soundcards found. <6>[ 6.454685] Freeing unused kernel memory: 7552K <6>[ 6.512911] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.560076] udevd[134]: starting version 3.2.9 <5>[ 7.576852] random: crng init done <27>[ 7.579683] udevd[134]: specified user 'tss' unknown <27>[ 7.579727] udevd[134]: specified group 'tss' unknown <30>[ 7.580614] udevd[135]: starting eudev-3.2.9 <27>[ 7.991828] udevd[148]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <28>[ 7.991855] udevd[148]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 8.018077] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 8.018143] fsl_ddr_edac acquired irq 111 for MC <6>[ 8.018146] fsl_ddr_edac MC err registered <6>[ 8.049873] NET: Registered PF_INET6 protocol family <6>[ 8.067241] Segment Routing with IPv6 <6>[ 8.067254] In-situ OAM (IOAM) with IPv6 <4>[ 8.111193] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 8.123688] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 8.139324] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 8.139339] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 8.140456] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 8.140570] rtc-rv8803 0-0032: registered as rtc0 <6>[ 8.141999] mscc_felix 0000:00:00.5: Adding to iommu group 13 <6>[ 8.142127] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 8.158860] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 8.158944] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 8.158974] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 8.158995] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 8.159014] wm8904 2-001a: supply MICVDD not found, using dummy regulator <4>[ 8.159626] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 8.159632] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 8.162117] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 8.163964] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 8.164487] wm8904 2-001a: revision A <6>[ 8.164840] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 8.166785] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 8.167880] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 8.259871] CAN device driver interface <4>[ 8.306781] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <4>[ 8.326212] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 8.342515] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 8.474622] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.474668] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 8.477356] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.505860] mali-dp f080000.display: Adding to iommu group 14 <6>[ 8.506201] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 8.514805] caam 8000000.crypto: Entropy delay = 3200 <6>[ 8.534892] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 8.554963] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 8.554977] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 8.554982] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 8.637475] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 8.657787] caam algorithms registered in /proc/crypto <6>[ 8.658748] caam 8000000.crypto: registering rng-caam <6>[ 8.658923] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 8.659183] caam_jr 8020000.jr: Adding to iommu group 16 done <6>[ 8.659624] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 8.660190] caam_jr 8040000.jr: Adding to iommu group 18 Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-410132/environment . /lava-410132/environment / # /lava-410132/bin/lava-test-runner /lava-410132/0 /lava-410132/bin/lava-test-runner /lava-410132/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-410132/0/tests/0_dmesg <8>[ 9.278669] + cat uuid + UUID=410132_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.293948] <8>[ 9.306976] <8>[ 9.320734] + set +x <8>[ 9.329771] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-410132/environment / # . /lava-410132/environment/lava-410132/bin/lava-test-runner /lava-410132/1 / # /lava-410132/bin/lava-test-runner /lava-410132/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-410132/1/tests/1_bootrr<8>[ 9.786508] + cat uuid + UUID=410132_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-410132/<8>[ 9.802463] 1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-au<8>[ 9.817409] to /lava-410132<8>[ 9.823216] /1/../bin/lava-test-case /lava-410132/1/../bin/lava-test-case /lava-410132/1/.<8>[ 9.842129] ./bin/lava-test-case /lava-410132/1/../bin/lava-test-case /lava-410132/1/../bin/lava-test-case<8>[ 9.857001] /lava-410132/1/../bin/lava-test-case <8>[ 9.872468] /lava-410132/1/../bin/lava-test-case <8>[ 9.885232] /lava-410132/1/../bin/lava-test-case <8>[ 9.900588] /lava-410132/1/../bin/lava-test-case <8>[ 9.913305] /lava-410132/1/../bin/lava-test-case <8>[ 9.928763] /lava-410132/1/../bin/lava-test-case <8>[ 9.940485] /lava-410132/1/../bin/lava-test-case <8>[ 9.951720] /lava-410132/1/../bin/lava-test-case <8>[ 9.964391] /lava-410132/1/../bin/lava-test-case <8>[ 9.975431] /lava-410132/1/../bin/lava-test-case <8>[ 9.987284] /lava-410132/1/../bin/lava-test-case <8>[ 9.999918] /lava-410132/1/../bin/lava-test-case <8>[ 10.011792] /lava-410132/1/../bin/lava-test-case <8>[ 10.023575] /lava-410132/1/../bin/lava-test-case <8>[ 10.035492] /lava-410132/1/../bin/lava-test-case <8>[ 10.049056] /lava-410132/1/../bin/lava-test-case <8>[ 10.060874] /lava-410132/1/../bin/lava-test-case <8>[ 10.072810] /lava-410132/1/../bin/lava-test-case <8>[ 10.084566] /lava-410132/1/../bin/lava-test-case <8>[ 10.097456] /lava-410132/1/../bin/lava-test-case <8>[ 10.115713] /lava-410132/1/../bin/lava-test-case <8>[ 10.128831] /lava-410132/1/../bin/lava-test-case <8>[ 10.140514] /lava-410132/1/../bin/lava-test-case <8>[ 10.152710] /lava-410132/1/../bin/lava-test-case <8>[ 10.163882] /lava-410132/1/../bin/lava-test-case <8>[ 10.176507] /lava-410132/1/../bin/lava-test-case <8>[ 10.188156] /lava-410132/1/../bin/lava-test-case <8>[ 10.199768] /lava-410132/1/../bin/lava-test-case <8>[ 10.211584] /lava-410132/1/../bin/lava-test-case <8>[ 10.223579] /lava-410132/1/../bin/lava-test-case <8>[ 10.235274] /lava-410132/1/../bin/lava-test-case <8>[ 10.247234] /lava-410132/1/../bin/lava-test-case <8>[ 10.259210] /lava-410132/1/../bin/lava-test-case <8>[ 10.271517] /lava-410132/1/../bin/lava-test-case <8>[ 10.283513] /lava-410132/1/../bin/lava-test-case <8>[ 10.296404] /lava-410132/1/../bin/lava-test-case <8>[ 10.308567] /lava-410132/1/../bin/lava-test-case <8>[ 10.320743] /lava-410132/1/../bin/lava-test-case <8>[ 10.332417] /lava-410132/1/../bin/lava-test-case <8>[ 10.344902] /lava-410132/1/../bin/lava-test-case <8>[ 10.356807] /lava-410132/1/../bin/lava-test-case <8>[ 10.368665] /lava-410132/1/../bin/lava-test-case <8>[ 10.379784] /lava-410132/1/../bin/lava-test-case <8>[ 10.392238] /lava-410132/1/../bin/lava-test-case <8>[ 10.404549] /lava-410132/1/../bin/lava-test-case <8>[ 10.416508] /lava-410132/1/../bin/lava-test-case <8>[ 10.428032] /lava-410132/1/../bin/lava-test-case <8>[ 10.440201] /lava-410132/1/../bin/lava-test-case <8>[ 10.451588] /lava-410132/1/../bin/lava-test-case <8>[ 10.465539] /lava-410132/1/../bin/lava-test-case <8>[ 10.478368] /lava-410132/1/../bin/lava-test-case <8>[ 10.491126] /lava-410132/1/../bin/lava-test-case <8>[ 10.503569] /lava-410132/1/../bin/lava-test-case <8>[ 10.515215] /lava-410132/1/../bin/lava-test-case <8>[ 10.527251] /lava-410132/1/../bin/lava-test-case <8>[ 10.538662] /lava-410132/1/../bin/lava-test-case <8>[ 10.552605] /lava-410132/1/../bin/lava-test-case <8>[ 10.564055] /lava-410132/1/../bin/lava-test-case <8>[ 10.575983] /lava-410132/1/../bin/lava-test-case <8>[ 10.587923] /lava-410132/1/../bin/lava-test-case <8>[ 10.599902] /lava-410132/1/../bin/lava-test-case <8>[ 10.612738] /lava-410132/1/../bin/lava-test-case <8>[ 10.624908] /lava-410132/1/../bin/lava-test-case <8>[ 10.637130] /lava-410132/1/../bin/lava-test-case <8>[ 10.655604] /lava-410132/1/../bin/lava-test-case <8>[ 10.668372] /lava-410132/1/../bin/lava-test-case <8>[ 10.681276] /lava-410132/1/../bin/lava-test-case <8>[ 10.697096] /lava-410132/1/../bin/lava-test-case <8>[ 10.708624] /lava-410132/1/../bin/lava-test-case <8>[ 10.719403] /lava-410132/1/../bin/lava-test-case <8>[ 10.732800] /lava-410132/1/../bin/lava-test-case <8>[ 10.743951] /lava-410132/1/../bin/lava-test-case <8>[ 10.757262] /lava-410132/1/../bin/lava-test-case <8>[ 10.768794] /lava-410132/1/../bin/lava-test-case <8>[ 10.781114] /lava-410132/1/../bin/lava-test-case <8>[ 10.792783] /lava-410132/1/../bin/lava-test-case <8>[ 10.806902] /lava-410132/1/../bin/lava-test-case <8>[ 10.820063] /lava-410132/1/../bin/lava-test-case <8>[ 10.832688] /lava-410132/1/../bin/lava-test-case <8>[ 10.844134] /lava-410132/1/../bin/lava-test-case <8>[ 10.855978] /lava-410132/1/../bin/lava-test-case <8>[ 10.868839] /lava-410132/1/../bin/lava-test-case <8>[ 10.880571] /lava-410132/1/../bin/lava-test-case <8>[ 10.892653] /lava-410132/1/../bin/lava-test-case <8>[ 10.904391] /lava-410132/1/../bin/lava-test-case <8>[ 10.916178] /lava-410132/1/../bin/lava-test-case <8>[ 10.929237] /lava-410132/1/../bin/lava-test-case <8>[ 10.941110] /lava-410132/1/../bin/lava-test-case <8>[ 10.952989] /lava-410132/1/../bin/lava-test-case <8>[ 10.967935] /lava-410132/1/../bin/lava-test-case <8>[ 10.980151] /lava-410132/1/../bin/lava-test-case <8>[ 10.991766] /lava-410132/1/../bin/lava-test-case <8>[ 11.004394] /lava-410132/1/../bin/lava-test-case <8>[ 11.016713] /lava-410132/1/../bin/lava-test-case <8>[ 11.029560] /lava-410132/1/../bin/lava-test-case <8>[ 11.045266] + set +x