[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.12 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12919893/tftp-deploy-ouejk2za/kernel/zImage tftp 0x10000000 12919893/tftp-deploy-ouejk2za/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '12919893/tftp-deploy-ouejk2za/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 3.4 MiB/s done Bytes transferred = 10523136 (a09200 hex) => tftp 0x14000000 12919893/tftp-deploy-ouejk2za/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12919893/tftp-deploy-ouejk2za/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '12919893/tftp-deploy-ouejk2za/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 3.1 MiB/s done Bytes transferred = 17166620 (105f11c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12919893/tftp-deploy-ouejk2za/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12919893/tftp-deploy-ouejk2za/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '12919893/tftp-deploy-ouejk2za/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.3 MiB/s done Bytes transferred = 42711 (a6d7 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xa09200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17166556 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6d6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.80-cip15 (KernelCI@build-j128602-arm-gcc-10-multi-v7-defconfig-dmx9z) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Mar 2 22:07:31 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 930384K/1048576K available (14336K kernel code, 2469K rwdata, 6208K rodata, 2048K init, 428K bss, 52656K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000001] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008088] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021991] Console: colour dummy device 80x30 <6>[ 0.023896] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034562] CPU: Testing write buffer coherency: ok <6>[ 0.039691] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044989] pid_max: default: 32768 minimum: 301 <6>[ 0.050035] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057454] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066377] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072242] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079778] rcu: Hierarchical SRCU implementation. <6>[ 0.083180] rcu: Max phase no-delay instances is 1000. <6>[ 0.092249] EFI services will not be available. <6>[ 0.094563] smp: Bringing up secondary CPUs ... <6>[ 0.099815] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099831] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.111124] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.111140] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.122333] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.122350] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.132749] smp: Brought up 1 node, 4 CPUs <6>[ 0.137014] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.143517] CPU: All CPU(s) started in SVC mode. <6>[ 0.148985] devtmpfs: initialized <6>[ 0.160073] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.165375] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.175302] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.185739] pinctrl core: initialized pinctrl subsystem <6>[ 0.192040] DMI not present or invalid. <6>[ 0.194107] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.202985] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.209946] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.210011] cpuidle: using governor menu <6>[ 0.217984] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.230085] platform soc: Fixed dependency cycle(s) with /soc/bus@2000000/gpc@20dc000 <6>[ 0.250457] platform 20dc000.gpc: Fixed dependency cycle(s) with /soc/bus@2000000/clock-controller@20c4000 <6>[ 0.258994] platform 20e0000.pinctrl: Fixed dependency cycle(s) with /soc/bus@2000000/pinctrl@20e0000/imx6q-sabrelite/hoggrp <6>[ 0.284719] No ATAGs? <6>[ 0.284900] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.292686] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.302069] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.315090] Serial: AMBA PL011 UART driver <6>[ 0.319492] printk: console [ramoops-1] enabled <6>[ 0.321676] pstore: Registered ramoops as persistent store backend <6>[ 0.327912] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.365895] iommu: Default domain type: Translated <6>[ 0.368197] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.375535] SCSI subsystem initialized <6>[ 0.379260] usbcore: registered new interface driver usbfs <6>[ 0.384506] usbcore: registered new interface driver hub <6>[ 0.390112] usbcore: registered new device driver usb <4>[ 0.395573] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.403454] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.411857] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.419761] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.430069] i2c i2c-0: IMX I2C adapter registered <6>[ 0.434251] i2c i2c-1: IMX I2C adapter registered <6>[ 0.438836] i2c i2c-2: IMX I2C adapter registered <6>[ 0.444361] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.448170] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.457573] PTP clock support registered <6>[ 0.461978] EDAC MC: Ver: 3.0.0 <6>[ 0.468966] vgaarb: loaded <6>[ 0.475043] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.487804] NET: Registered PF_INET protocol family <6>[ 0.490534] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.499665] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.506421] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.514389] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.522479] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.530166] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.536695] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.543378] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.550876] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.557193] RPC: Registered named UNIX socket transport module. <6>[ 0.562749] RPC: Registered udp transport module. <6>[ 0.567733] RPC: Registered tcp transport module. <6>[ 0.572663] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.579381] PCI: CLS 0 bytes, default 64 <4>[ 0.584162] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 0.584273] Trying to unpack rootfs image as initramfs... <6>[ 0.602456] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 0.610008] Initialise system trusted keyrings <6>[ 0.612992] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.625426] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.629538] NFS: Registering the id_resolver key type <5>[ 0.634031] Key type id_resolver registered <5>[ 0.638475] Key type id_legacy registered <6>[ 0.642830] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.649736] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.657397] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.662538] Key type asymmetric registered <5>[ 0.666296] Asymmetric key parser 'x509' registered <6>[ 0.671599] bounce: pool size: 64 pages <6>[ 0.675649] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.683152] io scheduler mq-deadline registered <6>[ 0.687955] io scheduler kyber registered <6>[ 0.757672] mxs-dma 110000.dma-apbh: initialized <6>[ 0.836369] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.845432] SuperH (H)SCI(F) driver initialized <6>[ 0.848540] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 269, base_baud = 5000000) is a IMX <6>[ 0.857493] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 270, base_baud = 5000000) is a IMX <6>[ 0.865385] printk: console [ttymxc1] enabled <6>[ 0.865385] printk: console [ttymxc1] enabled <6>[ 0.874522] printk: bootconsole [ec_imx21] disabled <6>[ 0.874522] printk: bootconsole [ec_imx21] disabled <6>[ 0.886456] msm_serial: driver initialized <6>[ 0.892028] STMicroelectronics ASC driver initialized <6>[ 0.899357] STM32 USART driver initialized <6>[ 0.926387] brd: module loaded <6>[ 0.937263] loop: module loaded <6>[ 0.944757] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 0.953010] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 0.961315] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 0.969786] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 0.977838] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 0.985647] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 0.993262] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 1.004012] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.011331] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.020454] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.032001] scsi host0: ahci-imx <6>[ 1.035933] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 <6>[ 1.058098] CAN device driver interface <6>[ 1.064159] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.074172] pps pps0: new PPS source ptp0 <3>[ 1.100192] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address <6>[ 1.107676] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 <6>[ 1.115049] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 <6>[ 1.122388] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 <6>[ 1.129738] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 <6>[ 1.137112] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 <6>[ 1.144435] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 <6>[ 1.151792] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 <6>[ 1.385563] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 1.391329] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 1.397911] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.068165] Freeing initrd memory: 16768K <4>[ 2.072806] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.083528] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 2.111845] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.119485] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.124727] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.131015] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.136703] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.149353] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.155268] usbcore: registered new interface driver pegasus <6>[ 2.161248] usbcore: registered new interface driver asix <6>[ 2.166978] usbcore: registered new interface driver ax88179_178a <6>[ 2.173377] usbcore: registered new interface driver cdc_ether <6>[ 2.179543] usbcore: registered new interface driver smsc75xx <6>[ 2.185624] usbcore: registered new interface driver smsc95xx <6>[ 2.191683] usbcore: registered new interface driver net1080 <6>[ 2.197665] usbcore: registered new interface driver cdc_subset <6>[ 2.203889] usbcore: registered new interface driver zaurus <6>[ 2.209821] usbcore: registered new interface driver cdc_ncm <6>[ 2.222607] usbcore: registered new interface driver usb-storage <6>[ 2.237737] i2c_dev: i2c /dev entries driver <6>[ 2.266328] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.272790] sdhci: Copyright(c) Pierre Ossman <6>[ 2.280468] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.289405] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.301093] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 2.301313] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 2.306398] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 2.317120] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.325491] usbcore: registered new interface driver usbhid <6>[ 2.331343] usbhid: USB HID core driver <6>[ 2.345561] NET: Registered PF_INET6 protocol family <6>[ 2.348907] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 2.359256] Segment Routing with IPv6 <6>[ 2.363255] In-situ OAM (IOAM) with IPv6 <6>[ 2.367575] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.374409] NET: Registered PF_PACKET protocol family <6>[ 2.379761] can: controller area network core <6>[ 2.384461] NET: Registered PF_CAN protocol family <6>[ 2.389560] can: raw protocol <6>[ 2.389671] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 2.392799] can: broadcast manager protocol <6>[ 2.404442] can: netlink gateway - max_hops=1 <5>[ 2.409479] Key type dns_resolver registered <6>[ 2.415956] ThumbEE CPU extension supported. <5>[ 2.420514] Registering SWP/SWPB emulation handler <5>[ 2.426469] Loading compiled-in X.509 certificates <6>[ 2.437832] pstore: Using crash dump compression: deflate <4>[ 2.479100] imx_usb 2184200.usb: No over current polarity defined <6>[ 2.486512] mmc2: new high speed SDHC card at address 0001 <6>[ 2.493285] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 2.497949] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.503138] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 2.511141] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.518847] GPT:29296874 != 30965759 <4>[ 2.522697] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.528991] GPT:29296874 != 30965759 <4>[ 2.532840] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.538350] mmcblk2: p1 p2 p3 <6>[ 2.565101] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.572274] hub 1-0:1.0: USB hub found <6>[ 2.576573] hub 1-0:1.0: 1 port detected <3>[ 2.585798] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 2.593395] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 2.601812] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <6>[ 2.618167] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 2.634966] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 2.865093] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.066723] hub 1-1:1.0: USB hub found <6>[ 3.070942] hub 1-1:1.0: 3 ports detected <6>[ 5.775509] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 5.783504] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.825102] Sending DHCP requests ., OK <6>[ 5.869302] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.12 <6>[ 5.877673] IP-Config: Complete: <6>[ 5.881187] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.12, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.891944] host=imx6q-sabrelite-lava-cbg-1, domain=lava-rack, nis-domain=(none) <6>[ 5.900066] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.900078] nameserver0=192.168.201.1 <6>[ 5.917756] Freeing unused kernel image (initmem) memory: 2048K <6>[ 5.946084] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.124067] udevd[125]: starting version 3.2.9 <5>[ 8.725055] random: crng init done <27>[ 8.737945] udevd[125]: specified user 'tss' unknown <27>[ 8.743407] udevd[125]: specified group 'tss' unknown <30>[ 8.751624] udevd[126]: starting eudev-3.2.9 <6>[ 9.173793] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 9.181497] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 9.335835] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 9.392544] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.413323] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.435165] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 9.442128] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 9.495225] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 9.525157] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 9.531559] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 9.585142] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 9.768498] caam 2100000.crypto: Entropy delay = 3200 <4>[ 9.800878] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 9.834632] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 9.895392] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 9.900828] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 9.907758] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 10.097099] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 10.107102] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <3>[ 10.234489] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' <6>[ 10.490937] caam algorithms registered in /proc/crypto <6>[ 10.497984] caam 2100000.crypto: registering rng-caam <6>[ 10.503650] caam 2100000.crypto: rng crypto API alg registered prng-caam done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12919893/environment . /lava-12919893/environment / # /lava-12919893/bin/lava-test-runner /lava-12919893/0 /lava-12919893/bin/lava-test-runner /lava-12919893/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12919893/0/tests/0_dmesg + cat uuid + UUID=12919893_1.5.2.4.1<8>[ 11.332045] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.398573] <8>[ 11.442486] <8>[ 11.486010] + set<8>[ 11.496143] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12919893/environment / # . /lava-12919893/environment/lava-12919893/bin/lava-test-runner /lava-12919893/1 / # /lava-12919893/bin/lava-test-runner /lava-12919893/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12919893/1/tests/1_bootrr + cat uuid <8>[ 12.032427] + UUID=12919893_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12919893/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd platform: supplier 2080000.pwm not ready backlight-lvds platform: supplier 208c000.pwm not ready panel-lcd platform: supplier backlight-lcd not ready panel-lvds0 platform: supplier backlight-lvds not ready ldb disp0 /lava-12919893/1/../bin/lava-test-case <8>[ 13.125592] /lava-12919893/1/../bin/lava-test-case <8>[ 13.183687] /lava-12919893/1/../bin/lava-test-case <8>[ 13.215592] + set +x <8>[ 13.246182] / #