[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 13684913/tftp-deploy-l7papv_n/kernel/zImage tftp 0x10000000 13684913/tftp-deploy-l7papv_n/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '13684913/tftp-deploy-l7papv_n/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ### 14 MiB/s done Bytes transferred = 10531328 (a0b200 hex) => tftp 0x14000000 13684913/tftp-deploy-l7papv_n/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 13684913/tftp-deploy-l7papv_n/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '13684913/tftp-deploy-l7papv_n/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 14.3 MiB/s done Bytes transferred = 17168614 (105f8e6 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 13684913/tftp-deploy-l7papv_n/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 13684913/tftp-deploy-l7papv_n/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '13684913/tftp-deploy-l7papv_n/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 6.8 MiB/s done Bytes transferred = 42719 (a6df hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xa0b200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17168550 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6de Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.90-cip20-rt11 (KernelCI@build-j189238-arm-gcc-10-multi-v7-defconfig-zs8dw) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed May 8 00:28:30 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 930384K/1048576K available (14336K kernel code, 2470K rwdata, 6212K rodata, 2048K init, 427K bss, 52656K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022579] Console: colour dummy device 80x30 <6>[ 0.024481] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034887] CPU: Testing write buffer coherency: ok <6>[ 0.040018] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.045315] pid_max: default: 32768 minimum: 301 <6>[ 0.050361] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057782] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066676] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072562] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080320] rcu: Hierarchical SRCU implementation. <6>[ 0.080325] rcu: Max phase no-delay instances is 1000. <6>[ 0.080417] printk: bootconsole [ec_imx21] printing thread started <6>[ 0.099179] EFI services will not be available. <6>[ 0.099553] smp: Bringing up secondary CPUs ... <6>[ 0.100379] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.100396] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.101319] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.101336] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.102239] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.102256] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.102356] smp: Brought up 1 node, 4 CPUs <6>[ 0.102368] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.102378] CPU: All CPU(s) started in SVC mode. <6>[ 0.102961] devtmpfs: initialized <6>[ 0.110897] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.111119] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.111142] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.114464] pinctrl core: initialized pinctrl subsystem <6>[ 0.118441] DMI not present or invalid. <6>[ 0.119275] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.214039] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.216828] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.219853] cpuidle: using governor menu <6>[ 0.220111] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.227658] platform soc: Fixed dependency cycle(s) with /soc/bus@2000000/gpc@20dc000 <6>[ 0.228863] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.229046] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.243274] platform 20dc000.gpc: Fixed dependency cycle(s) with /soc/bus@2000000/clock-controller@20c4000 <6>[ 0.244284] platform 20e0000.iomuxc-gpr:ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.244376] platform 20e0000.iomuxc-gpr:ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000 <6>[ 0.244740] platform 20e0000.iomuxc-gpr:ipu2_csi1_mux: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.244828] platform 20e0000.iomuxc-gpr:ipu2_csi1_mux: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000 <6>[ 0.245139] platform 20e0000.pinctrl: Fixed dependency cycle(s) with /soc/bus@2000000/pinctrl@20e0000/imx6q-sabrelite/hoggrp <6>[ 0.250984] platform 20e0000.iomuxc-gpr:ipu2_csi1_mux: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000 <6>[ 0.251147] platform 20e0000.iomuxc-gpr:ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000 <6>[ 0.251242] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2100000/i2c@21a4000/camera@40 <6>[ 0.251294] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu2_csi1_mux <6>[ 0.251407] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.251448] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.251483] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux <6>[ 0.252452] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.252647] platform 20e0000.iomuxc-gpr:ipu1_csi0_mux: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.252826] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.252996] platform ldb: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.253116] platform 2400000.ipu: Fixed dependency cycle(s) with /ldb/lvds-channel@0 <6>[ 0.253171] platform 2400000.ipu: Fixed dependency cycle(s) with /soc/hdmi@120000 <6>[ 0.253281] platform 2400000.ipu: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000 <6>[ 0.253390] platform 2400000.ipu: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux <6>[ 0.254768] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.254950] platform 20e0000.iomuxc-gpr:ipu2_csi1_mux: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.255118] platform 120000.hdmi: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.255288] platform ldb: Fixed dependency cycle(s) with /soc/ipu@2800000 <6>[ 0.255401] platform 2800000.ipu: Fixed dependency cycle(s) with /ldb/lvds-channel@0 <6>[ 0.255456] platform 2800000.ipu: Fixed dependency cycle(s) with /soc/hdmi@120000 <6>[ 0.255586] platform 2800000.ipu: Fixed dependency cycle(s) with /soc/bus@2000000/iomuxc-gpr@20e0000/ipu2_csi1_mux <6>[ 0.255698] platform 2800000.ipu: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000 <6>[ 0.262023] platform 2400000.ipu: Fixed dependency cycle(s) with /disp0 <6>[ 0.262248] platform disp0: Fixed dependency cycle(s) with /soc/ipu@2400000 <6>[ 0.262609] platform disp0: Fixed dependency cycle(s) with /panel-lcd <6>[ 0.262841] platform panel-lcd: Fixed dependency cycle(s) with /disp0 <6>[ 0.263252] platform ldb: Fixed dependency cycle(s) with /panel-lvds0 <6>[ 0.263565] platform panel-lvds0: Fixed dependency cycle(s) with /ldb/lvds-channel@0 <6>[ 0.264952] No ATAGs? <6>[ 0.571815] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.571827] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.575267] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.584291] Serial: AMBA PL011 UART driver <6>[ 0.587238] printk: console [ramoops-1] enabled <6>[ 0.587276] printk: console [ramoops-1] printing thread started <6>[ 0.587490] pstore: Registered ramoops as persistent store backend <6>[ 0.587498] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.653767] iommu: Default domain type: Translated <6>[ 0.653777] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.654576] SCSI subsystem initialized <6>[ 0.655081] usbcore: registered new interface driver usbfs <6>[ 0.655126] usbcore: registered new interface driver hub <6>[ 0.655166] usbcore: registered new device driver usb <4>[ 0.655396] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 0.655532] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 0.655688] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 0.655817] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 0.657833] i2c i2c-0: IMX I2C adapter registered <6>[ 0.658589] platform 21dc000.mipi: Fixed dependency cycle(s) with /soc/bus@2100000/i2c@21a4000/camera@40 <6>[ 0.658853] i2c 1-0040: Fixed dependency cycle(s) with /soc/bus@2100000/mipi@21dc000 <6>[ 0.659381] i2c i2c-1: IMX I2C adapter registered <6>[ 0.660309] i2c i2c-2: IMX I2C adapter registered <6>[ 0.661833] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.661841] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.661860] PTP clock support registered <6>[ 0.662123] EDAC MC: Ver: 3.0.0 <6>[ 0.666014] vgaarb: loaded <6>[ 0.781448] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.791691] NET: Registered PF_INET protocol family <6>[ 0.792124] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.794028] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.794057] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.794074] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.794159] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.794444] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.794657] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.794703] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.794897] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.795488] RPC: Registered named UNIX socket transport module. <6>[ 0.795498] RPC: Registered udp transport module. <6>[ 0.795502] RPC: Registered tcp transport module. <6>[ 0.795506] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.795515] PCI: CLS 0 bytes, default 64 <4>[ 0.796155] armv7-pmu pmu: hw perfevents: no interrupt-affinity property, guessing. <6>[ 0.796196] Trying to unpack rootfs image as initramfs... <6>[ 0.815853] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 0.817972] Initialise system trusted keyrings <6>[ 0.818312] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.824454] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.825268] NFS: Registering the id_resolver key type <5>[ 0.825347] Key type id_resolver registered <5>[ 0.825353] Key type id_legacy registered <6>[ 0.825442] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.825450] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.825485] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.825968] Key type asymmetric registered <5>[ 0.825977] Asymmetric key parser 'x509' registered <6>[ 0.826133] bounce: pool size: 64 pages <6>[ 0.826257] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 0.826266] io scheduler mq-deadline registered <6>[ 0.826273] io scheduler kyber registered <6>[ 1.060170] mxs-dma 110000.dma-controller: initialized <6>[ 1.139314] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.144841] SuperH (H)SCI(F) driver initialized <6>[ 1.145983] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 269, base_baud = 5000000) is a IMX <6>[ 1.159221] printk: console [ttymxc1] enabled <6>[ 1.159230] printk: bootconsole [ec_imx21] disabled <6>[ 1.159270] printk: console [ttymxc1] printing thread started <6>[ 1.159268] printk: bootconsole [ec_imx21] printing thread stopped <6>[ 1.185770] msm_serial: driver initialized <6>[ 1.185783] STMicroelectronics ASC driver initialized <6>[ 1.187600] STM32 USART driver initialized <6>[ 1.210428] brd: module loaded <6>[ 1.218299] loop: module loaded <6>[ 1.222513] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.222531] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.222540] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.222549] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 1.222644] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 1.222817] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 1.222907] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 1.225817] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.225846] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.225863] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.307999] scsi host0: ahci-imx <6>[ 1.308353] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 271 <6>[ 1.322192] CAN device driver interface <6>[ 1.324039] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.327989] pps pps0: new PPS source ptp0 <3>[ 1.352609] mdio_bus 2188000.ethernet-1: ethernet-phy has invalid PHY address <6>[ 1.352628] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 0 <6>[ 1.352728] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 1 <6>[ 1.352813] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 2 <6>[ 1.352895] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 3 <6>[ 1.352977] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 4 <6>[ 1.353057] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 5 <6>[ 1.353139] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 6 <6>[ 1.353219] mdio_bus 2188000.ethernet-1: scan phy ethernet-phy at address 7 <6>[ 1.663094] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 1.663168] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 1.663178] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.253814] Freeing initrd memory: 16768K <4>[ 2.254223] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.254254] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 2.287902] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.289431] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.289436] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.289503] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.289509] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.296457] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 2.296503] usbcore: registered new interface driver pegasus <6>[ 2.296549] usbcore: registered new interface driver asix <6>[ 2.296594] usbcore: registered new interface driver ax88179_178a <6>[ 2.296630] usbcore: registered new interface driver cdc_ether <6>[ 2.296676] usbcore: registered new interface driver smsc75xx <6>[ 2.296720] usbcore: registered new interface driver smsc95xx <6>[ 2.296752] usbcore: registered new interface driver net1080 <6>[ 2.296783] usbcore: registered new interface driver cdc_subset <6>[ 2.296816] usbcore: registered new interface driver zaurus <6>[ 2.296893] usbcore: registered new interface driver cdc_ncm <6>[ 2.303886] usbcore: registered new interface driver usb-storage <6>[ 2.312838] i2c_dev: i2c /dev entries driver <6>[ 2.337087] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.337095] sdhci: Copyright(c) Pierre Ossman <6>[ 2.340096] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.342816] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.348620] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 2.348657] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 2.348828] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 2.439714] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.441974] usbcore: registered new interface driver usbhid <6>[ 2.441983] usbhid: USB HID core driver <6>[ 2.452263] NET: Registered PF_INET6 protocol family <6>[ 2.453985] Segment Routing with IPv6 <6>[ 2.454043] In-situ OAM (IOAM) with IPv6 <6>[ 2.454130] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.454774] NET: Registered PF_PACKET protocol family <6>[ 2.454782] can: controller area network core <6>[ 2.454855] NET: Registered PF_CAN protocol family <6>[ 2.454863] can: raw protocol <6>[ 2.454871] can: broadcast manager protocol <6>[ 2.454881] can: netlink gateway - max_hops=1 <5>[ 2.455231] Key type dns_resolver registered <6>[ 2.459704] ThumbEE CPU extension supported. <5>[ 2.459720] Registering SWP/SWPB emulation handler <5>[ 2.463280] Loading compiled-in X.509 certificates <6>[ 2.469388] pstore: Using crash dump compression: deflate <6>[ 2.493796] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 2.494291] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 2.528686] mmc2: new high speed SDHC card at address 0001 <6>[ 2.529598] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 2.557408] imx_usb 2184200.usb: No over current polarity defined <6>[ 2.561103] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.561126] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 2.583788] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.583796] GPT:7812499 != 30560255 <4>[ 2.583803] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.583806] GPT:7812499 != 30560255 <4>[ 2.583812] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.583859] mmcblk2: p1 p2 p3 <6>[ 2.611446] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.613420] hub 1-0:1.0: USB hub found <6>[ 2.613509] hub 1-0:1.0: 1 port detected <6>[ 2.618573] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.625827] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 2.641159] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 2.901495] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.103149] hub 1-1:1.0: USB hub found <6>[ 3.103349] hub 1-1:1.0: 3 ports detected <6>[ 5.761872] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 5.761934] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.791509] Sending DHCP requests ., OK <6>[ 5.831552] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 5.831578] IP-Config: Complete: <6>[ 5.831584] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.831611] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 5.831624] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.831639] nameserver0=192.168.201.1 <6>[ 5.831985] clk: Disabling unused clocks <6>[ 5.840302] Freeing unused kernel image (initmem) memory: 2048K <6>[ 5.841342] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.970287] udevd[129]: starting version 3.2.9 <5>[ 11.131398] random: crng init done <27>[ 11.138765] udevd[129]: specified user 'tss' unknown <27>[ 11.138872] udevd[129]: specified group 'tss' unknown <30>[ 11.141311] udevd[130]: starting eudev-3.2.9 <6>[ 11.571146] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 11.574068] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 11.653523] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 11.762149] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.792086] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.801579] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 11.801696] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 11.824137] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 11.824244] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 11.824259] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 11.891738] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 12.022444] caam 2100000.crypto: Entropy delay = 3200 <4>[ 12.070987] fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW <6>[ 12.083246] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 12.144007] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 12.144028] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 12.144037] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 12.308752] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 12.313218] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <3>[ 12.408533] fsl-asoc-card sound: ASoC: driver name too long 'imx6q-sabrelite-sgtl5000' -> 'imx6q-sabrelite' <6>[ 12.669440] caam algorithms registered in /proc/crypto <6>[ 12.670749] caam 2100000.crypto: registering rng-caam <6>[ 12.671063] caam 2100000.crypto: rng crypto API alg registered prng-caam done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-13684913/environment . /lava-13684913/environment / # /lava-13684913/bin/lava-test-runner /lava-13684913/0 /lava-13684913/bin/lava-test-runner /lava-13684913/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-13684913/0/tests/0_dmesg + cat uuid + UUID=13684913_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 13.471838] <8>[ 13.512404] <8>[ 13.547055] + set +x