[Enter `^Ec?' for help] U-Boot SPL 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45) U-Boot 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45 +0000) Model: Radxa Rock 2 Square DRAM: 2 GiB MMC: dwmmc@ff0c0000: 0, dwmmc@ff0f0000: 1 In: serial@ff690000 Out: serial@ff690000 Err: serial@ff690000 Incorrect eeprom header Net: eth0: ethernet@ff290000 Hit any key to stop autoboot: 1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@ff290000 Waiting for PHY auto negotiation to complete...... done Speed: 1000, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.201.22 (761 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x2000000 14173440/tftp-deploy-v4grmmg0/kernel/zImage tftp 0x2000000 14173440/tftp-deploy-v4grmmg0/kernel/zImage Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '14173440/tftp-deploy-v4grmmg0/kernel/zImage'. Load address: 0x2000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ### 3.1 MiB/s done Bytes transferred = 10535424 (a0c200 hex) => tftp 0x4000000 14173440/tftp-deploy-v4grmmg0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4000000 14173440/tftp-deploy-v4grmmg0/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '14173440/tftp-deploy-v4grmmg0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# # 3.3 MiB/s done Bytes transferred = 17188781 (10647ad hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x1f00000 14173440/tftp-deploy-v4grmmg0/dtb/rk3288-rock2-square.dtb tftp 0x1f00000 14173440/tftp-deploy-v4grmmg0/dtb/rk3288-rock2-square.dtb Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '14173440/tftp-deploy-v4grmmg0/dtb/rk3288-rock2-square.dtb'. Load address: 0x1f00000 Loading: *### 2.5 MiB/s done Bytes transferred = 41716 (a2f4 hex) => setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x2000000 0x4000000 0x1f00000 bootz 0x2000000 0x4000000 0x1f00000 Kernel image @ 0x2000000 [ 0x000000 - 0xa0c200 ] ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17188717 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Using Device Tree in place at 01f00000, end 01f0d2f3 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 6.1.92-cip22-rt12 (KernelCI@build-j217257-arm-gcc-10-multi-v7-defconfig-z4j96) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Jun 5 00:22:26 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Radxa Rock 2 Square [ 0.000000] earlycon: uart0 at MMIO32 0xff690000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1970740K/2097152K available (14336K kernel code, 2470K rwdata, 6212K rodata, 2048K init, 427K bss, 60876K reserved, 65536K cma-reserved, 1245184K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009084] Switching to timer-based delay loop, resolution 41ns <6>[ 0.023464] Console: colour dummy device 80x30 <6>[ 0.028685] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.040361] CPU: Testing write buffer coherency: ok <6>[ 0.046040] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.051886] pid_max: default: 32768 minimum: 301 <6>[ 0.057421] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.065762] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.075513] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500 <6>[ 0.083131] Setting up static identity map for 0x300000 - 0x3000ac <6>[ 0.092396] rcu: Hierarchical SRCU implementation. <6>[ 0.092401] rcu: Max phase no-delay instances is 1000. <6>[ 0.092493] printk: bootconsole [uart0] printing thread started <6>[ 0.115688] EFI services will not be available. <6>[ 0.116037] smp: Bringing up secondary CPUs ... <6>[ 0.117847] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501 <6>[ 0.117866] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.119788] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502 <6>[ 0.119807] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.121717] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503 <6>[ 0.121735] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.121857] smp: Brought up 1 node, 4 CPUs <6>[ 0.121870] SMP: Total of 4 processors activated (192.00 BogoMIPS). <6>[ 0.121881] CPU: All CPU(s) started in SVC mode. <6>[ 0.122495] devtmpfs: initialized <6>[ 0.132310] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0 <6>[ 0.132547] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.132569] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.134578] pinctrl core: initialized pinctrl subsystem <6>[ 0.138469] DMI not present or invalid. <6>[ 0.139304] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.243379] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.246376] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.246443] cpuidle: using governor menu <6>[ 0.247116] No ATAGs? <6>[ 0.247256] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.247268] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.250742] Serial: AMBA PL011 UART driver <6>[ 0.274889] platform ff940000.vop: Fixed dependency cycle(s) with /hdmi@ff980000 <6>[ 0.274985] platform ff930000.vop: Fixed dependency cycle(s) with /hdmi@ff980000 <6>[ 0.275073] platform ff980000.hdmi: Fixed dependency cycle(s) with /vop@ff940000 <6>[ 0.275161] platform ff980000.hdmi: Fixed dependency cycle(s) with /vop@ff930000 <6>[ 0.291029] rockchip-gpio ff750000.gpio: probed /pinctrl/gpio@ff750000 <6>[ 0.291772] rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000 <6>[ 0.292502] rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000 <6>[ 0.293255] rockchip-gpio ff7a0000.gpio: probed /pinctrl/gpio@ff7a0000 <6>[ 0.294061] rockchip-gpio ff7b0000.gpio: probed /pinctrl/gpio@ff7b0000 <6>[ 0.294765] rockchip-gpio ff7c0000.gpio: probed /pinctrl/gpio@ff7c0000 <6>[ 0.295487] rockchip-gpio ff7d0000.gpio: probed /pinctrl/gpio@ff7d0000 <6>[ 0.296212] rockchip-gpio ff7e0000.gpio: probed /pinctrl/gpio@ff7e0000 <6>[ 0.296923] rockchip-gpio ff7f0000.gpio: probed /pinctrl/gpio@ff7f0000 <6>[ 0.412305] iommu: Default domain type: Translated <6>[ 0.412314] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.413211] SCSI subsystem initialized <6>[ 0.413710] usbcore: registered new interface driver usbfs <6>[ 0.413764] usbcore: registered new interface driver hub <6>[ 0.413808] usbcore: registered new device driver usb <6>[ 0.416471] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.416478] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.416505] PTP clock support registered <6>[ 0.416773] EDAC MC: Ver: 3.0.0 <6>[ 0.420635] vgaarb: loaded <6>[ 0.483030] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.503452] NET: Registered PF_INET protocol family <6>[ 0.503707] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.506037] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.506071] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.506090] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.506172] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.506545] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.506639] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.506692] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.506892] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.507533] RPC: Registered named UNIX socket transport module. <6>[ 0.507542] RPC: Registered udp transport module. <6>[ 0.507546] RPC: Registered tcp transport module. <6>[ 0.507551] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.507560] PCI: CLS 0 bytes, default 64 <6>[ 0.508216] Trying to unpack rootfs image as initramfs... <6>[ 0.523585] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available <5>[ 0.525456] Initialise system trusted keyrings <6>[ 0.525714] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.533205] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.534010] NFS: Registering the id_resolver key type <5>[ 0.534051] Key type id_resolver registered <5>[ 0.534057] Key type id_legacy registered <6>[ 0.534162] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.534171] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.534207] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.534866] Key type asymmetric registered <5>[ 0.534875] Asymmetric key parser 'x509' registered <6>[ 0.535061] bounce: pool size: 64 pages <6>[ 0.535183] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 0.535192] io scheduler mq-deadline registered <6>[ 0.535198] io scheduler kyber registered <6>[ 0.787131] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 0.787147] dma-pl330 ff250000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 <6>[ 0.807928] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 0.807943] dma-pl330 ffb20000.dma-controller: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10 <6>[ 0.891306] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 0.894777] printk: console [ttyS2] disabled <6>[ 0.905547] printk: console [ttyS2] enabled <6>[ 0.905558] printk: bootconsole [uart0] disabled <6>[ 0.905559] printk: console [ttyS2] printing thread started <6>[ 0.922551] printk: bootconsole [uart0] printing thread stopped <6>[ 0.926313] SuperH (H)SCI(F) driver initialized <6>[ 0.928050] msm_serial: driver initialized <6>[ 0.928056] STMicroelectronics ASC driver initialized <6>[ 0.929901] STM32 USART driver initialized <6>[ 0.967458] brd: module loaded <6>[ 0.974496] loop: module loaded <6>[ 0.992837] CAN device driver interface <6>[ 0.994920] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 0.996939] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 0.996944] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 0.997008] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 0.997013] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.004973] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.005027] usbcore: registered new interface driver pegasus <6>[ 1.005083] usbcore: registered new interface driver asix <6>[ 1.005136] usbcore: registered new interface driver ax88179_178a <6>[ 1.005177] usbcore: registered new interface driver cdc_ether <6>[ 1.005228] usbcore: registered new interface driver smsc75xx <6>[ 1.005279] usbcore: registered new interface driver smsc95xx <6>[ 1.005320] usbcore: registered new interface driver net1080 <6>[ 1.005367] usbcore: registered new interface driver cdc_subset <6>[ 1.005407] usbcore: registered new interface driver zaurus <6>[ 1.005486] usbcore: registered new interface driver cdc_ncm <4>[ 1.008904] dwc2 ff540000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.009070] dwc2 ff540000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.120215] dwc2 ff540000.usb: DWC OTG Controller <6>[ 1.120248] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1 <6>[ 1.120287] dwc2 ff540000.usb: irq 51, io mem 0xff540000 <6>[ 1.121206] hub 1-0:1.0: USB hub found <6>[ 1.121253] hub 1-0:1.0: 1 port detected <4>[ 1.122008] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.122173] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.253118] dwc2 ff580000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM <6>[ 1.321655] dwc2 ff580000.usb: DWC OTG Controller <6>[ 1.321689] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2 <6>[ 1.321727] dwc2 ff580000.usb: irq 52, io mem 0xff580000 <6>[ 1.322552] hub 2-0:1.0: USB hub found <6>[ 1.322601] hub 2-0:1.0: 1 port detected <6>[ 1.328219] usbcore: registered new interface driver usb-storage <6>[ 1.337182] i2c_dev: i2c /dev entries driver <6>[ 1.340756] ehci-platform ff500000.usb: EHCI Host Controller <6>[ 1.340784] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 3 <6>[ 1.344102] i2c 0-005a: Fixed dependency cycle(s) with /i2c@ff650000/act8846@5a/regulators/REG4 <6>[ 1.344214] i2c 0-005a: Fixed dependency cycle(s) with /i2c@ff650000/act8846@5a/regulators/REG2 <6>[ 1.348631] VDD_LOG: Bringing 1100000uV into 1000000-1000000uV <6>[ 1.374848] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! <6>[ 1.379423] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! <4>[ 1.402282] dw_wdt ff800000.watchdog: No valid TOPs array specified <6>[ 1.413273] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 500000 KHz, changing to: 600000 KHz <6>[ 1.416477] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.416483] sdhci: Copyright(c) Pierre Ossman <6>[ 1.419139] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.421467] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.426960] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 1.477027] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.478810] usbcore: registered new interface driver usbhid <6>[ 1.478818] usbhid: USB HID core driver <6>[ 1.482642] NET: Registered PF_INET6 protocol family <6>[ 1.482872] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 1.482878] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 1.482902] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 1.490491] Segment Routing with IPv6 <6>[ 1.490513] In-situ OAM (IOAM) with IPv6 <6>[ 1.490547] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.490805] NET: Registered PF_PACKET protocol family <6>[ 1.490808] can: controller area network core <6>[ 1.490834] NET: Registered PF_CAN protocol family <6>[ 1.490837] can: raw protocol <6>[ 1.490841] can: broadcast manager protocol <6>[ 1.490844] can: netlink gateway - max_hops=1 <5>[ 1.491010] Key type dns_resolver registered <6>[ 1.491058] ThumbEE CPU extension supported. <5>[ 1.491063] Registering SWP/SWPB emulation handler <5>[ 1.491476] Loading compiled-in X.509 certificates <6>[ 1.512671] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 1.512720] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 1.513275] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input). <6>[ 1.513280] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30). <6>[ 1.513284] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10). <6>[ 1.513290] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no). <6>[ 1.513308] rk_gmac-dwmac ff290000.ethernet: clock input from PHY <6>[ 1.518316] rk_gmac-dwmac ff290000.ethernet: init for RGMII <6>[ 1.523069] rk_gmac-dwmac ff290000.ethernet: User ID: 0x10, Synopsys ID: 0x35 <6>[ 1.523079] rk_gmac-dwmac ff290000.ethernet: DWMAC1000 <6>[ 1.523083] rk_gmac-dwmac ff290000.ethernet: DMA HW capability register supported <6>[ 1.523085] rk_gmac-dwmac ff290000.ethernet: RX Checksum Offload Engine supported <6>[ 1.523087] rk_gmac-dwmac ff290000.ethernet: COE Type 2 <6>[ 1.523090] rk_gmac-dwmac ff290000.ethernet: TX Checksum insertion supported <6>[ 1.523092] rk_gmac-dwmac ff290000.ethernet: Wake-Up On Lan supported <6>[ 1.523136] rk_gmac-dwmac ff290000.ethernet: Normal descriptors <6>[ 1.523139] rk_gmac-dwmac ff290000.ethernet: Ring mode enabled <6>[ 1.523142] rk_gmac-dwmac ff290000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 1.707379] Freeing initrd memory: 16788K <6>[ 1.737657] ehci-platform ff500000.usb: irq 54, io mem 0xff500000 <6>[ 1.739242] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL) <6>[ 1.739247] RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bus:phy_addr=stmmac-0:01, irq=POLL) <6>[ 1.744428] dwmmc_rockchip ff0f0000.mmc: IDMAC supports 32-bit address mode. <6>[ 1.744521] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 1.745498] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 1.745883] dwmmc_rockchip ff0c0000.mmc: IDMAC supports 32-bit address mode. <6>[ 1.763025] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00 <6>[ 1.763297] hub 3-0:1.0: USB hub found <6>[ 1.763313] hub 3-0:1.0: 1 port detected <6>[ 1.821893] dwmmc_rockchip ff0f0000.mmc: Using internal DMA controller. <6>[ 1.821901] dwmmc_rockchip ff0f0000.mmc: Version ID is 270a <6>[ 1.821929] dwmmc_rockchip ff0f0000.mmc: DW MMC controller at irq 62,32 bit host data width,256 deep fifo <6>[ 1.822041] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 1.822048] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 1.822058] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 1.822114] dwmmc_rockchip ff0c0000.mmc: Using internal DMA controller. <6>[ 1.822120] dwmmc_rockchip ff0c0000.mmc: Version ID is 270a <6>[ 1.822136] dwmmc_rockchip ff0c0000.mmc: DW MMC controller at irq 63,32 bit host data width,256 deep fifo <6>[ 1.824446] dwmmc_rockchip ff0f0000.mmc: allocated mmc-pwrseq <6>[ 1.824450] mmc_host mmc0: card is non-removable. <6>[ 1.828014] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 1.836948] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 1.837911] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 1.917487] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) <6>[ 1.917958] mmc0: new high speed MMC card at address 0001 <6>[ 1.918277] mmcblk0: mmc0:0001 032GE4 29.1 GiB <6>[ 1.921266] mmcblk0: p1 p2 <6>[ 1.921656] mmcblk0boot0: mmc0:0001 032GE4 4.00 MiB <6>[ 1.922551] mmcblk0boot1: mmc0:0001 032GE4 4.00 MiB <6>[ 1.923306] mmcblk0rpmb: mmc0:0001 032GE4 4.00 MiB, chardev (236:0) <6>[ 1.985355] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 1.985362] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 1.985377] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 1.995280] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.020130] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.020154] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.020194] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.020843] rk_gmac-dwmac ff290000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 <6>[ 2.024835] rk_gmac-dwmac ff290000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet] (irq=POLL) <6>[ 2.033046] rk_gmac-dwmac ff290000.ethernet eth0: No Safety Features support found <6>[ 2.033067] rk_gmac-dwmac ff290000.ethernet eth0: PTP not supported by HW <6>[ 2.053055] usb 3-1: new high-speed USB device number 2 using ehci-platform <6>[ 2.093722] rk_gmac-dwmac ff290000.ethernet eth0: configuring for phy/rgmii link mode <6>[ 2.257381] hub 3-1:1.0: USB hub found <6>[ 2.257898] hub 3-1:1.0: 4 ports detected <6>[ 2.280633] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.280694] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.280701] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.280718] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 5.244291] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 5.244393] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.283021] Sending DHCP requests ., OK <6>[ 5.323305] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.22 <6>[ 5.323358] IP-Config: Complete: <6>[ 5.323370] device=eth0, hwaddr=4a:01:9c:e5:04:ff, ipaddr=192.168.201.22, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.323428] host=rk3288-rock2-square-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 5.323456] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.323489] nameserver0=192.168.201.1 <6>[ 5.324150] clk: Disabling unused clocks <4>[ 5.326614] dw-apb-uart ff690000.serial: forbid DMA for kernel console <6>[ 5.337909] Freeing unused kernel image (initmem) memory: 2048K <6>[ 5.404518] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.459500] udevd[118]: starting version 3.2.9 <5>[ 5.460380] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.460841] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.461234] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.466084] udevd[118]: specified user 'tss' unknown <27>[ 5.466157] udevd[118]: specified group 'tss' unknown <30>[ 5.467313] udevd[119]: starting eudev-3.2.9 <6>[ 5.618812] rockchip-vop ff930000.vop: Adding to iommu group 0 <6>[ 5.619121] rockchip-vop ff940000.vop: Adding to iommu group 1 <6>[ 5.621869] rockchip-drm display-subsystem: bound ff930000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 5.622128] rockchip-drm display-subsystem: bound ff940000.vop (ops vop_component_ops [rockchipdrm]) <4>[ 5.622231] dwhdmi-rockchip ff980000.hdmi: supply avdd-0v9 not found, using dummy regulator <4>[ 5.622321] dwhdmi-rockchip ff980000.hdmi: supply avdd-1v8 not found, using dummy regulator <6>[ 5.622405] dwhdmi-rockchip ff980000.hdmi: Detected HDMI TX controller v2.00a with HDCP (DWC MHL PHY) <6>[ 5.622622] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 5.623322] rockchip-drm display-subsystem: bound ff980000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm]) <6>[ 5.624209] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0 <6>[ 5.624241] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 5.633213] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 5.633226] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 5.644275] usbcore: registered new device driver onboard-usb-hub <6>[ 5.712310] rtc-hym8563 0-0051: registered as rtc0 <6>[ 5.713530] rtc-hym8563 0-0051: setting system clock to 2024-06-05T00:37:59 UTC (1717547879) <6>[ 5.763720] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 5.763729] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 5.763747] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 5.765004] dwmmc_rockchip ff0d0000.mmc: allocated mmc-pwrseq <6>[ 5.765012] mmc_host mmc1: card is non-removable. <6>[ 5.780041] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 5.799707] panfrost ffa30000.gpu: clock rate = 400000000 <6>[ 5.810119] rk3288-crypto ff8a0000.crypto: will run requests pump with realtime priority <6>[ 5.810427] panfrost ffa30000.gpu: mali-t760 id 0x750 major 0x0 minor 0x0 status 0x1 <6>[ 5.810433] panfrost ffa30000.gpu: features: 00000000,00000407, issues: 00000000,24040400 <6>[ 5.810438] panfrost ffa30000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 <6>[ 5.810444] panfrost ffa30000.gpu: shader_present=0xf l2_present=0x1 <6>[ 5.811361] [drm] Initialized panfrost 1.2.0 20180908 for ffa30000.gpu on minor 1 <6>[ 5.812494] rk3288-crypto ff8a0000.crypto: Crypto Accelerator successfully registered <6>[ 5.926048] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) <6>[ 5.928876] mmc1: new high speed SDIO card at address 0001 <6>[ 5.964909] usb 3-1: reset high-speed USB device number 2 using ehci-platform <5>[ 6.060510] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 6.090064] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <5>[ 6.091134] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 6.091198] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 6.091206] cfg80211: failed to load regulatory.db <6>[ 6.100077] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 6.100174] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.radxa,rock2-square.bin failed with error -2 <4>[ 6.100202] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <6>[ 6.404678] hub 3-1:1.0: USB hub found <6>[ 6.405052] hub 3-1:1.0: 4 ports detected <6>[ 6.412572] hub 3-1:1.0: USB hub found <6>[ 6.413237] hub 3-1:1.0: 4 ports detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 6.487308] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-14173440/environment . /lava-14173440/environment / # /lava-14173440/bin/lava-test-runner /lava-14173440/0 /lava-14173440/bin/lava-test-runner /lava-14173440/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-14173440/0/tests/0_dmesg + cat uuid + UUID=14173440_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.<8>[ 7.075059] sh <8>[ 7.100040] <3>[ 7.112537] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 <8>[ 7.115564] + set +x / # <8>[ 7.138387] <8>[ 7.139035]