[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7990005/tftp-deploy-seiwb6me/kernel/zImage tftp 0x10000000 7990005/tftp-deploy-seiwb6me/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '7990005/tftp-deploy-seiwb6me/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 11.5 MiB/s done Bytes transferred = 8819200 (869200 hex) => tftp 0x14000000 7990005/tftp-deploy-seiwb6me/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7990005/tftp-deploy-seiwb6me/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '7990005/tftp-deploy-seiwb6me/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 11.5 MiB/s done Bytes transferred = 13349199 (cbb14f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7990005/tftp-deploy-seiwb6me/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7990005/tftp-deploy-seiwb6me/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '7990005/tftp-deploy-seiwb6me/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.6 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x869200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13349135 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.265-cip85-rt27 (KernelCI@build-j511216-arm-gcc-10-defconfig-preempt-rt-lvlkj) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Wed Nov 16 01:38:48 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') <6>[ 0.000000] bootconsole [ec_imx21] enabled <6>[ 0.000000] Memory policy: Data cache writealloc <6>[ 0.000000] efi: Getting EFI parameters from FDT: <6>[ 0.000000] efi: UEFI not found. <3>[ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring <6>[ 0.000000] cma: Reserved 64 MiB at 0x4c000000 <6>[ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 <5>[ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 938548K/1048576K available (12288K kernel code, 1636K rwdata, 4692K rodata, 2048K init, 406K bss, 44492K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. <6>[ 0.000000] No expedited grace period (rcu_normal_after_boot). <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.000020] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.003125] Console: colour dummy device 80x30 <6>[ 0.271669] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.271679] pid_max: default: 32768 minimum: 301 <6>[ 0.271838] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.271858] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.272578] CPU: Testing write buffer coherency: ok <6>[ 0.272608] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.273047] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.318387] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.326014] rcu: Hierarchical SRCU implementation. <6>[ 0.333166] EFI services will not be available. <6>[ 0.335492] smp: Bringing up secondary CPUs ... <6>[ 0.341242] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.341249] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.342737] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.342743] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.344204] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.344210] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.344352] smp: Brought up 1 node, 4 CPUs <6>[ 0.379531] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.385965] CPU: All CPU(s) started in SVC mode. <6>[ 0.392052] devtmpfs: initialized <6>[ 0.405717] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.411377] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.420914] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.430670] pinctrl core: initialized pinctrl subsystem <6>[ 0.435409] DMI not present or invalid. <6>[ 0.438337] NET: Registered protocol family 16 <6>[ 0.447814] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.455250] cpuidle: using governor menu <6>[ 0.456811] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.474982] vdd1p1: supplied by regulator-dummy <6>[ 0.477631] vdd3p0: supplied by regulator-dummy <6>[ 0.482430] vdd2p5: supplied by regulator-dummy <6>[ 0.487193] vddarm: supplied by regulator-dummy <6>[ 0.492230] vddpu: supplied by regulator-dummy <6>[ 0.496461] vddsoc: supplied by regulator-dummy <6>[ 0.519886] No ATAGs? <6>[ 0.520012] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.527955] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.538474] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.545429] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.558979] Serial: AMBA PL011 UART driver <6>[ 0.563475] console [pstore-1] enabled <6>[ 0.564851] pstore: Registered ramoops as persistent store backend <6>[ 0.571074] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.610879] mxs-dma 110000.dma-apbh: initialized <6>[ 0.622998] vgaarb: loaded <5>[ 0.624269] SCSI subsystem initialized <6>[ 0.627681] usbcore: registered new interface driver usbfs <6>[ 0.632931] usbcore: registered new interface driver hub <6>[ 0.638479] usbcore: registered new device driver usb <6>[ 0.645655] i2c i2c-0: IMX I2C adapter registered <6>[ 0.648703] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.655293] i2c i2c-1: IMX I2C adapter registered <6>[ 0.659228] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.665565] i2c i2c-2: IMX I2C adapter registered <6>[ 0.669755] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.677253] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.680534] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.689954] PTP clock support registered <6>[ 0.694428] EDAC MC: Ver: 3.0.0 <6>[ 0.701190] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.799322] NET: Registered protocol family 2 <6>[ 0.801646] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.809203] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.816114] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.823471] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) <6>[ 0.830529] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.837038] UDP hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.843018] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.849846] NET: Registered protocol family 1 <6>[ 0.854907] RPC: Registered named UNIX socket transport module. <6>[ 0.860343] RPC: Registered udp transport module. <6>[ 0.865304] RPC: Registered tcp transport module. <6>[ 0.870258] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.877586] Trying to unpack rootfs image as initramfs... <6>[ 2.108618] Freeing initrd memory: 13040K <4>[ 2.110458] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.117751] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.128592] Initialise system trusted keyrings <6>[ 2.130921] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.148473] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.152859] NFS: Registering the id_resolver key type <5>[ 2.157136] Key type id_resolver registered <5>[ 2.161471] Key type id_legacy registered <6>[ 2.165784] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.173099] Key type asymmetric registered <5>[ 2.174694] Asymmetric key parser 'x509' registered <6>[ 2.179940] bounce: pool size: 64 pages <6>[ 2.183958] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 2.191575] io scheduler noop registered <6>[ 2.195747] io scheduler deadline registered <6>[ 2.200628] io scheduler cfq registered (default) <6>[ 2.205234] io scheduler mq-deadline registered <6>[ 2.210015] io scheduler kyber registered <6>[ 2.243464] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.248042] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.255218] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.262477] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.282781] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.289693] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <4>[ 2.296470] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.296550] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.296606] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.296736] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 2.296886] PU : no governor for states <6>[ 2.296905] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 2.378454] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.387001] SuperH (H)SCI(F) driver initialized <6>[ 2.390244] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 2.399066] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 2.409602] console [ttymxc1] enabled <6>[ 2.409602] console [ttymxc1] enabled <6>[ 2.414592] bootconsole [ec_imx21] disabled <6>[ 2.414592] bootconsole [ec_imx21] disabled <6>[ 2.425119] msm_serial: driver initialized <6>[ 2.430982] STMicroelectronics ASC driver initialized <6>[ 2.438107] STM32 USART driver initialized <4>[ 2.455886] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.464602] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.471626] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.478414] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.487470] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.494651] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.513720] brd: module loaded <6>[ 2.531173] loop: module loaded <6>[ 2.538897] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.547100] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.555384] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.563841] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.574665] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.581929] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.590994] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.602283] scsi host0: ahci-imx <6>[ 2.606554] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.629556] CAN device driver interface <6>[ 2.635207] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.642593] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.651573] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.661000] pps pps0: new PPS source ptp0 <6>[ 2.695373] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.703089] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.709194] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.715465] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.722700] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.736021] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.743760] usbcore: registered new interface driver pegasus <6>[ 2.749766] usbcore: registered new interface driver asix <6>[ 2.755495] usbcore: registered new interface driver ax88179_178a <6>[ 2.761918] usbcore: registered new interface driver cdc_ether <6>[ 2.768086] usbcore: registered new interface driver smsc75xx <6>[ 2.774174] usbcore: registered new interface driver smsc95xx <6>[ 2.780237] usbcore: registered new interface driver net1080 <6>[ 2.786235] usbcore: registered new interface driver cdc_subset <6>[ 2.792482] usbcore: registered new interface driver zaurus <6>[ 2.798419] usbcore: registered new interface driver cdc_ncm <6>[ 2.808095] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.814899] ehci-pci: EHCI PCI platform driver <6>[ 2.819679] ehci-platform: EHCI generic platform driver <6>[ 2.825566] ehci-orion: EHCI orion driver <6>[ 2.830138] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.834688] ehci-st: EHCI STMicroelectronics driver <6>[ 2.840102] ehci-exynos: EHCI EXYNOS driver <6>[ 2.844818] ehci-atmel: EHCI Atmel driver <6>[ 2.849341] tegra-ehci: Tegra EHCI driver <6>[ 2.853913] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.860387] ohci-pci: OHCI PCI platform driver <6>[ 2.865166] ohci-platform: OHCI generic platform driver <6>[ 2.871004] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.875556] ohci-st: OHCI STMicroelectronics driver <6>[ 2.880959] ohci-atmel: OHCI Atmel driver <6>[ 2.886472] usbcore: registered new interface driver usb-storage <6>[ 2.895602] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.908527] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.918973] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.924162] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.942783] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.948488] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.955032] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.961258] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.962232] hub 1-0:1.0: USB hub found <6>[ 2.962290] hub 1-0:1.0: 1 port detected <6>[ 2.971134] i2c /dev entries driver <6>[ 2.990375] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.003402] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.009854] sdhci: Copyright(c) Pierre Ossman <6>[ 3.017293] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.026100] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.032997] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 3.038442] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 3.043994] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.085323] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 3.094433] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 3.100037] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.139000] mmc0: new high speed SDHC card at address 59b4 <6>[ 3.141540] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 3.147219] usbcore: registered new interface driver usbhid <6>[ 3.147223] usbhid: USB HID core driver <6>[ 3.155392] NET: Registered protocol family 10 <6>[ 3.156903] Segment Routing with IPv6 <6>[ 3.156993] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.157807] NET: Registered protocol family 17 <6>[ 3.157825] can: controller area network core (rev 20170425 abi 9) <6>[ 3.157938] NET: Registered protocol family 29 <6>[ 3.157950] can: raw protocol (rev 20170425) <6>[ 3.157958] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.157973] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 3.158557] Key type dns_resolver registered <6>[ 3.160140] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 3.160236] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 3.160340] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 3.161655] ThumbEE CPU extension supported. <5>[ 3.161673] Registering SWP/SWPB emulation handler <5>[ 3.163080] Loading compiled-in X.509 certificates <6>[ 3.164799] pstore: Using compression: deflate <6>[ 3.190073] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.190176] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.192122] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.192212] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.194041] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.194143] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.194247] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.195709] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.195776] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.195874] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.198041] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 3.199200] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.199289] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.200805] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.200891] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.202718] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.202812] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.202910] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.204365] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.204433] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.204532] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.205816] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.205897] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.207312] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.207394] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.209076] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.209144] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.209241] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.210678] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.210763] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.210859] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.214064] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.214407] hctosys: unable to open rtc device (rtc0) <6>[ 3.221566] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.221662] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.223317] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.223403] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.225161] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.225239] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.225340] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.226780] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.226870] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.226964] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.251239] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.331918] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.332043] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 3.458899] hub 1-1:1.0: USB hub found <6>[ 3.458994] hub 1-1:1.0: 3 ports detected <6>[ 3.603647] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.611053] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.619757] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.622559] mmcblk0: mmc0:59b4 SD 14.7 GiB <6>[ 3.632522] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.642966] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.653451] panel-simple panel-lcd: Linked as a consumer to regulator.0 <4>[ 3.658464] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.658469] GPT:29296874 != 30863359 <4>[ 3.658472] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.658476] GPT:29296874 != 30863359 <4>[ 3.658478] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.658520] mmcblk0: p1 p2 p3 <6>[ 3.692116] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.700506] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.709559] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.716720] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.724812] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.732217] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.740766] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.748254] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.757140] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.765833] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.772815] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.472141] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.481338] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.511261] Sending DHCP requests ., OK <6>[ 6.565576] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 6.573862] IP-Config: Complete: <6>[ 6.577367] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.588076] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 6.596181] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.596187] nameserver0=192.168.201.1 <6>[ 6.614612] Freeing unused kernel memory: 2048K <6>[ 6.619735] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.765006] udevd[143]: starting version 3.2.9 <5>[ 6.770968] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.778018] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.784847] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.799050] udevd[143]: specified user 'tss' unknown <27>[ 6.804527] udevd[143]: specified group 'tss' unknown <30>[ 6.812562] udevd[144]: starting eudev-3.2.9 <4>[ 7.573772] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.583029] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.590625] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.602701] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.610158] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.621538] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.629063] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.637743] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <4>[ 7.647580] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.656924] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.663987] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.676557] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.682966] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.683965] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.684215] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.733833] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.765256] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.772087] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.778114] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.780893] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.781003] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.786674] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.786783] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.815364] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.824682] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.832734] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.843457] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 7.846707] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.846974] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.847080] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.889509] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.895889] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.916127] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.924442] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.933032] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.946566] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.954087] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.965286] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.974451] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.981477] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.992499] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 8.001925] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 8.009096] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 8.301593] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 8.309084] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 8.319888] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 8.329796] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 8.336606] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 8.337835] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.345729] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.357276] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 8.371929] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 8.382505] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 8.389566] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 8.401510] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 8.412603] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 8.419794] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 8.429892] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 8.438060] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 8.447477] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 8.455856] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 8.468366] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 8.477087] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 8.484100] panel-simple panel-lcd: Dropping the link to regulator.0 done Saving random seed: <5>[ 8.759622] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.867963] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7990005/environment . /lava-7990005/environment / # /lava-7990005/bin/lava-test-runner /lava-7990005/0 /lava-7990005/bin/lava-test-runner /lava-7990005/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-7990005/0/tests/0_dmesg + cat uuid + UUID=7990005_1.5.2.4.1 + set <8>[ 9.488789] +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.542756] <8>[ 9.590028] <8>[ 9.637987] + set +x <8>[ 9.648112] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7990005/environment / # . /lava-7990005/environment/lava-7990005/bin/lava-test-runner /lava-7990005/1 / # /lava-7990005/bin/lava-test-runner /lava-7990005/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-7990005/1/tests/1_bootrr + cat uuid + UUID=7990005_1.5.2.4.5 + <8>[ 10.178239] set +x + export 'PATH=/opt/bootrr/helpers:/lava-7990005/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7990005/1/../bin/lava-test-case <8>[ 11.243867] /lava-7990005/1/../bin/lava-test-case <8>[ 11.290158] /lava-7990005/1/../bin/lava-test-case <8>[ 11.318594] + set<8>[ 11.339820] +x / #