Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3009 device /dev/ttyimx7d-sdb-2 [115200 N81] (Debian GNU/Linux) U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 28C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.196 (1312 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1104173/tftp-deploy-64vbjl1d/kernel/zImage tftp 0x80800000 1104173/tftp-deploy-64vbjl1d/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.196; sending through gateway 172.16.1.4 Filename '1104173/tftp-deploy-64vbjl1d/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 10.2 MiB/s done Bytes transferred = 8823296 (86a200 hex) => tftp 0x86800000 1104173/tftp-deploy-64vbjl1d/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1104173/tftp-deploy-64vbjl1d/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.196; sending through gateway 172.16.1.4 Filename '1104173/tftp-deploy-64vbjl1d/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 10 MiB/s done Bytes transferred = 13332927 (cb71bf hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1104173/tftp-deploy-64vbjl1d/dtb/imx7d-sdb.dtb tftp 0x83000000 1104173/tftp-deploy-64vbjl1d/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.196; sending through gateway 172.16.1.4 Filename '1104173/tftp-deploy-64vbjl1d/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 4 MiB/s done Bytes transferred = 33576 (8328 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x86a200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13332863 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300b327 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.265-cip85-rt27 (KernelCI@build-j511275-arm-gcc-10-multi-v7-defconfig-preempt-rt-t7bjz) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Wed Nov 16 01:40:40 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') <6>[ 0.000000] bootconsole [ec_imx6q0] enabled <6>[ 0.000000] Memory policy: Data cache writealloc <6>[ 0.000000] efi: Getting EFI parameters from FDT: <6>[ 0.000000] efi: UEFI not found. <6>[ 0.000000] cma: Reserved 64 MiB at 0xbc000000 <6>[ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 <5>[ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 938740K/1048576K available (12288K kernel code, 1636K rwdata, 4692K rodata, 2048K init, 406K bss, 44300K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. <6>[ 0.000000] No expedited grace period (rcu_normal_after_boot). <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000007] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.000016] Switching to timer-based delay loop, resolution 125ns <6>[ 0.001084] Switching to timer-based delay loop, resolution 41ns <6>[ 0.001098] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.001110] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.004444] Console: colour dummy device 80x30 <6>[ 0.258445] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.258457] pid_max: default: 32768 minimum: 301 <6>[ 0.258635] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.258651] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.259495] CPU: Testing write buffer coherency: ok <6>[ 0.259961] CPU0: update cpu_capacity 1024 <6>[ 0.297778] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.304674] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.312113] rcu: Hierarchical SRCU implementation. <6>[ 0.319342] EFI services will not be available. <6>[ 0.321578] smp: Bringing up secondary CPUs ... <6>[ 0.327415] smp: Brought up 1 node, 1 CPU <6>[ 0.330400] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.336868] CPU: All CPU(s) started in SVC mode. <6>[ 0.342766] devtmpfs: initialized <6>[ 0.356921] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.362662] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.372214] futex hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.381298] pinctrl core: initialized pinctrl subsystem <6>[ 0.386344] DMI not present or invalid. <6>[ 0.389394] NET: Registered protocol family 16 <6>[ 0.398413] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.406443] cpuidle: using governor menu <6>[ 0.408512] No ATAGs? <6>[ 0.408583] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.418638] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.427945] Serial: AMBA PL011 UART driver <6>[ 0.440835] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <4>[ 0.446757] imx7d-pinctrl 30330000.iomuxc: Failed to create dummy-iomuxc-gpr@30340000 debugfs directory <6>[ 0.455622] imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver <6>[ 0.464703] vdd1p0d: Bringing 0uV into 800000-800000uV <6>[ 0.468003] vdd1p0d: supplied by regulator-dummy <6>[ 0.473447] vdd1p2: supplied by regulator-dummy <6>[ 0.541524] mxs-dma 33000000.dma-apbh: initialized <6>[ 0.552712] vgaarb: loaded <5>[ 0.554071] SCSI subsystem initialized <6>[ 0.557606] usbcore: registered new interface driver usbfs <6>[ 0.562726] usbcore: registered new interface driver hub <6>[ 0.568282] usbcore: registered new device driver usb <6>[ 0.575681] i2c i2c-0: IMX I2C adapter registered <6>[ 0.578563] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.585272] i2c i2c-1: IMX I2C adapter registered <6>[ 0.589148] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.595598] i2c i2c-2: IMX I2C adapter registered <6>[ 0.599734] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.606385] i2c i2c-3: IMX I2C adapter registered <6>[ 0.610322] i2c i2c-3: can't use DMA, using PIO instead. <6>[ 0.617863] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.621262] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.630641] PTP clock support registered <6>[ 0.635120] EDAC MC: Ver: 3.0.0 <6>[ 0.642338] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.753745] NET: Registered protocol family 2 <6>[ 0.755868] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.763841] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.770625] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.778040] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) <6>[ 0.785220] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.791580] UDP hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.797693] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.804598] NET: Registered protocol family 1 <6>[ 0.809684] RPC: Registered named UNIX socket transport module. <6>[ 0.815120] RPC: Registered udp transport module. <6>[ 0.820103] RPC: Registered tcp transport module. <6>[ 0.825094] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.832629] Trying to unpack rootfs image as initramfs... <6>[ 2.067597] Freeing initrd memory: 13024K <6>[ 2.069648] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 2.080122] Initialise system trusted keyrings <6>[ 2.082750] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.103352] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.107957] NFS: Registering the id_resolver key type <5>[ 2.112004] Key type id_resolver registered <5>[ 2.116422] Key type id_legacy registered <6>[ 2.120762] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.128831] Key type asymmetric registered <5>[ 2.130351] Asymmetric key parser 'x509' registered <6>[ 2.135680] bounce: pool size: 64 pages <6>[ 2.139678] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.147331] io scheduler noop registered <6>[ 2.151525] io scheduler deadline registered <6>[ 2.156502] io scheduler cfq registered (default) <6>[ 2.161063] io scheduler mq-deadline registered <6>[ 2.165879] io scheduler kyber registered <4>[ 2.198035] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 2.204078] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 2.211062] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 2.231274] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <6>[ 2.238320] imx-sdma 30bd0000.sdma: external firmware not found, using ROM firmware <4>[ 2.247248] imx7-pgc imx7-pgc-domain.1: DMA mask not set <6>[ 2.247417] imx7-pgc imx7-pgc-domain.1: Linked as a consumer to regulator.1 <4>[ 2.264293] reset_imx7 30390000.src: Failed to create dummy-src@30390000 debugfs directory <6>[ 2.354883] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.363833] SuperH (H)SCI(F)W���<6>[ 2.368393] console [ttymxc0] enabled <6>[ 2.368393] console [ttymxc0] enabled <6>[ 2.373445] bootconsole [ec_imx6q0] disabled <6>[ 2.373445] bootconsole [ec_imx6q0] disabled <6>[ 2.383911] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 57, base_baud = 15000000) is a IMX <6>[ 2.396173] msm_serial: driver initialized <6>[ 2.400838] STMicroelectronics ASC driver initialized <6>[ 2.407878] STM32 USART driver initialized <6>[ 2.439447] brd: module loaded <6>[ 2.455764] loop: module loaded <6>[ 2.477717] CAN device driver interface <6>[ 2.483420] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.492123] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 2.501334] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.508346] fec 30be0000.ethernet: Dropping the link to regulator.0 <4>[ 2.517004] fec 30bf0000.ethernet: 30bf0000.ethernet supply phy not found, using dummy regulator <6>[ 2.526207] fec 30bf0000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.533814] pps pps0: new PPS source ptp0 <3>[ 2.539212] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 2.546313] fec 30bf0000.ethernet: Using random MAC address: b2:3c:d4:ca:9d:5e <6>[ 3.406197] fec 30bf0000.ethernet eth0: registered PHC device 0 <6>[ 3.413977] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.420081] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.426404] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.433663] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.446539] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.454321] usbcore: registered new interface driver pegasus <6>[ 3.460320] usbcore: registered new interface driver asix <6>[ 3.466077] usbcore: registered new interface driver ax88179_178a <6>[ 3.472521] usbcore: registered new interface driver cdc_ether <6>[ 3.478694] usbcore: registered new interface driver smsc75xx <6>[ 3.484801] usbcore: registered new interface driver smsc95xx <6>[ 3.490869] usbcore: registered new interface driver net1080 <6>[ 3.496857] usbcore: registered new interface driver cdc_subset <6>[ 3.503102] usbcore: registered new interface driver zaurus <6>[ 3.509064] usbcore: registered new interface driver cdc_ncm <6>[ 3.518510] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.525312] ehci-pci: EHCI PCI platform driver <6>[ 3.530092] ehci-platform: EHCI generic platform driver <6>[ 3.535937] ehci-orion: EHCI orion driver <6>[ 3.540476] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.544991] ehci-st: EHCI STMicroelectronics driver <6>[ 3.550360] ehci-exynos: EHCI EXYNOS driver <6>[ 3.555038] ehci-atmel: EHCI Atmel driver <6>[ 3.559533] tegra-ehci: Tegra EHCI driver <6>[ 3.564081] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.570557] ohci-pci: OHCI PCI platform driver <6>[ 3.575339] ohci-platform: OHCI generic platform driver <6>[ 3.581127] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.585640] ohci-st: OHCI STMicroelectronics driver <6>[ 3.591010] ohci-atmel: OHCI Atmel driver <6>[ 3.596463] usbcore: registered new interface driver usb-storage <6>[ 3.612920] i2c /dev entries driver <6>[ 3.635235] imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.649144] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.655604] sdhci: Copyright(c) Pierre Ossman <6>[ 3.662865] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.671437] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.678371] sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO <6>[ 3.683911] sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO <6>[ 3.723472] mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA <6>[ 3.732173] sdhci-esdhc-imx 30b50000.usdhc: Linked as a consumer to regulator.6 <6>[ 3.782537] mmc0: new high speed SDHC card at address aaaa <6>[ 3.789567] mmcblk0: mmc0:aaaa SA16G 14.8 GiB <6>[ 3.797268] mmcblk0: p1 p2 <6>[ 3.985001] mmc1: SDHCI controller on 30b50000.usdhc [30b50000.usdhc] using ADMA <6>[ 4.029255] mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA <4>[ 4.035640] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 4.039425] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 4.042524] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <6>[ 4.061007] usbcore: registered new interface driver usbhid <6>[ 4.066856] usbhid: USB HID core driver <6>[ 4.083575] NET: Registered protocol family 10 <6>[ 4.091853] Segment Routing with IPv6 <6>[ 4.095958] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.103404] NET: Registered protocol family 17 <6>[ 4.108139] can: controller area network core (rev 20170425 abi 9) <6>[ 4.116857] NET: Registered protocol family 29 <6>[ 4.121574] can: raw protocol (rev 20170425) <6>[ 4.128158] can: broadcast manager protocol (rev 20170425 t) <6>[ 4.135549] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 4.144053] Key type dns_resolver registered <6>[ 4.150907] ThumbEE CPU extension supported. <5>[ 4.155466] Registering SWP/SWPB emulation handler <5>[ 4.162664] Loading compiled-in X.509 certificates <6>[ 4.227435] mmc1: new ultra high speed SDR104 SDIO card at address 0001 <4>[ 4.271443] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 4.280331] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 4.287449] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 4.300867] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 4.310121] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 4.317151] fec 30be0000.ethernet: Dropping the link to regulator.0 <4>[ 4.336419] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 4.345293] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 4.352510] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 4.365908] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 4.375135] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 4.382132] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 4.400430] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.411246] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 4.412630] hctosys: unable to open rtc device (rtc0) <3>[ 4.428717] fec 30bf0000.ethernet eth0: Unable to connect to phy <6>[ 4.439130] pwm-backlight backlight: Linked as a consumer to regulator.0 <3>[ 4.443329] IP-Config: Failed to open eth0 <3>[ 4.443338] IP-Config: No network devices available <6>[ 4.455866] pwm-backlight backlight: Dropping the link to regulator.0 <6>[ 4.481680] Freeing unused kernel memory: 2048K <4>[ 4.486612] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 4.486743] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 4.486949] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 4.519544] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 4.722989] udevd[144]: starting version 3.2.9 <5>[ 4.729084] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 4.736257] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 4.743170] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 4.760736] udevd[144]: specified user 'tss' unknown <27>[ 4.766311] udevd[144]: specified group 'tss' unknown <30>[ 4.784309] udevd[145]: starting eudev-3.2.9 <6>[ 6.240835] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 6.321162] flexcan 30a10000.can: Linked as a consumer to regulator.7 <6>[ 6.322258] flexcan 30a10000.can: device registered (reg_base=(ptrval), irq=52) <4>[ 6.326610] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 6.326793] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 6.326935] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 6.404867] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 6.404989] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 6.405200] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 6.601261] [drm] No driver support for vblank timestamp query. <3>[ 6.632587] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 6.647535] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 6.657423] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 6.668337] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 6.740972] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 6.772790] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 6.779820] fec 30be0000.ethernet: Dropping the link to regulator.0 <5>[ 6.834148] cfg80211: Loading compiled-in X.509 certificates for regulatory database <4>[ 6.843886] usb_phy_generic usbphynop1: usbphynop1 supply vcc not found, using dummy regulator <6>[ 6.894230] usb_phy_generic usbphynop1: Linked as a consumer to regulator.0 <4>[ 6.901729] usb_phy_generic usbphynop3: usbphynop3 supply vcc not found, using dummy regulator <6>[ 6.925863] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 6.925872] [drm] No driver support for vblank timestamp query. <3>[ 6.926003] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 6.929650] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 6.929775] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 6.929910] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 7.010061] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 7.010185] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 7.010398] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 7.024589] imx_usb 30b10000.usb: Linked as a consumer to regulator.3 <6>[ 7.104203] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.104212] [drm] No driver support for vblank timestamp query. <3>[ 7.104324] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 7.108181] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 7.108312] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 7.108451] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 7.192029] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 7.192155] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 7.194618] fec 30be0000.ethernet: Dropping the link to regulator.0 <5>[ 7.417625] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 7.417815] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 7.417825] cfg80211: failed to load regulatory.db <6>[ 7.528297] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <6>[ 7.533011] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.533019] [drm] No driver support for vblank timestamp query. <3>[ 7.533131] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 7.537003] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 7.537130] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 7.537268] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 7.581984] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <4>[ 7.596504] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 7.596636] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 7.596859] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 7.631417] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 7.631426] [drm] No driver support for vblank timestamp query. <3>[ 7.631539] mxsfb 30730000.lcdif: Failed to create outputs <6>[ 7.942621] usb_phy_generic usbphynop3: Linked as a consumer to regulator.0 <4>[ 7.970658] pwm-backlight backlight: backlight supply power not found, using dummy regulator <4>[ 7.973302] usb_phy_generic usbphynop2: usbphynop2 supply vcc not found, using dummy regulator <6>[ 7.973431] usb_phy_generic usbphynop2: Linked as a consumer to regulator.0 <6>[ 8.042029] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 8.061160] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 8.107105] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 8.136630] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 8.148388] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 8.171187] imx_usb 30b20000.usb: Linked as a consumer to regulator.4 <6>[ 8.202886] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.222543] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.262391] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.274973] hub 1-0:1.0: USB hub found <6>[ 8.279295] hub 1-0:1.0: 1 port detected done <6>[ 8.308805] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 8.322052] [drm] No driver support for vblank timestamp query. <3>[ 8.328386] mxsfb 30730000.lcdif: Failed to create outputs Saving random seed: <4>[ 8.338851] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 8.354404] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 8.361520] pwm-backlight backlight: Dropping the link to regulator.0 OK <5>[ 8.367211] random: dd: uninitialized urandom read (32 bytes read) Starting network: <4>[ 8.401126] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 8.420782] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 8.427880] fec 30be0000.ethernet: Dropping the link to regulator.0 ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.514376] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # <3>[ 8.593885] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1104173/environment . /lava-1104173/environment / # /lava-1104173/bin/lava-test-runner /lava-1104173/0 /lava-1104173/bin/lava-test-runner /lava-1104173/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1104173/0/tests/0_dmesg + cat uuid + UUID=1104173_1.5.2.4.1<8>[ 14.363150] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.421171] <8>[ 14.474729] <8>[ 14.527895] + set +x<8>[ 14.538418] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1104173/environment / # . /lava-1104173/environment/lava-1104173/bin/lava-test-runner /lava-1104173/1 / # /lava-1104173/bin/lava-test-runner /lava-1104173/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1104173/1/tests/1_bootrr + cat uuid + UUID=1104173_1.5.2.4.5 <8>[ 20.294435] + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1104173/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1104173/1/../bin/lava-test-case <8>[ 21.350038] /lava-1104173/1/../bin/lava-test-case <8>[ 22.405536] /lava-1104173/1/../bin/lava-test-case <8>[ 22.435374] + set +x<8>[ 22.457873] / #