connecting to NetworkSerialPort(target=Target(name='imx6ul-pico-hobbit-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4007, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4007 connected to 10.8.254.5 (port 4007) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2017.10.1-00009-gbc5d99d030 #1 Wed Nov 1 17:19:43 CET 2017 Board: Technexion Pico i.MX6UL Board detected i.MX6 UltraLite revision 1.0 mdio_bus: miibus0: probed imx-usb 2184200.usb: USB EHCI 1.00 imx-esdhc 2190000.usdhc: registered as 2190000.usdhc imx-esdhc 2194000.usdhc: registered as 2194000.usdhc netconsole: registered as netconsole-1 malloc space: 0x8fefca40 -> 0x9fdf947f (size 255 MiB) mmc0: detected MMC card version 5.1 mmc0: registered mmc0.boot0 mmc0: registered mmc0.boot1 mmc0: registered mmc0 running /env/bin/init... [?25h Hit m for menu or any other key to stop autoboot: 3 type exit to get to the menu [1;32mbarebox@[1;36mTechnexion Pico i.MX6UL Board:/[0m bootm -v -r /mnt/tftp/829790/tftp-deploy-u7a4sasf/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/829790/tftp-deploy-u7a4sasf/dtb/imx6ul-pico-hobbit.dtb /mnt/tftp/829790/tftp-deploy-u7a4sasf/kernel/zImage [1;32mbarebox@[1;36mTechnexion Pico i.MX6UL Board:/[0m bootm -v -r /mnt/tftp/829790/tftp-deploy-u7a4sasf/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/829790/tftp-deploy-u7a4sasf/dtb/imx6ul-pico-hobbit.dtb /mnt/tftp/829790/tftp-deploy-u7a4sasf/kernel/zImage warning: No MAC address set. Using random address a2:ff:ad:48:63:2a eth1: 100Mbps full duplex link detected T DHCP client bound to address 10.8.254.69 Loading ARM Linux zImage '/mnt/tftp/829790/tftp-deploy-u7a4sasf/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler no OS load address, defaulting to 0x82a13000 no initrd load address, defaulting to 0x8337e000 Loaded initrd GZIP compressed '/mnt/tftp/829790/tftp-deploy-u7a4sasf/ramdisk/ramdisk.cpio.gz' initrd is at 0x8337e000-0x84033d53 Loading devicetree from '/mnt/tftp/829790/tftp-deploy-u7a4sasf/dtb/imx6ul-pico-hobbit.dtb' mmc0: Cannot find nodepath /soc/aips-bus@02100000/usdhc@02190000, cannot fixup Failed to fixup node in of_partition_fixup+0x1/0x1f8: Invalid argument commandline: console=ttymxc5,115200n8 Starting kernel at 0x82a13000, initrd at 0x8337e000, oftree at 0x84034000... Starting kernel in secure mode [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.265-cip85-rt27 (KernelCI@build-j511275-arm-gcc-10-multi-v7-defconfig-preempt-rt-t7bjz) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Wed Nov 16 01:40:40 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Technexion Pico i.MX6UL Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc5,115200n8 [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 418240K/524288K available (12288K kernel code, 1636K rwdata, 4692K rodata, 2048K init, 406K bss, 40512K reserved, 65536K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] No expedited grace period (rcu_normal_after_boot). [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.000049] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.005829] Console: colour dummy device 80x30 [ 0.006202] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.006227] pid_max: default: 32768 minimum: 301 [ 0.006608] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.006635] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.008479] CPU: Testing write buffer coherency: ok [ 0.009420] /cpus/cpu@0 missing clock-frequency property [ 0.009510] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.011981] Setting up static identity map for 0x80300000 - 0x803000a0 [ 0.014930] rcu: Hierarchical SRCU implementation. [ 0.022280] EFI services will not be available. [ 0.022872] smp: Bringing up secondary CPUs ... [ 0.022911] smp: Brought up 1 node, 1 CPU [ 0.022941] SMP: Total of 1 processors activated (48.00 BogoMIPS). [ 0.022964] CPU: All CPU(s) started in SVC mode. [ 0.024794] devtmpfs: initialized [ 0.044519] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.045873] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.045942] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.051311] pinctrl core: initialized pinctrl subsystem [ 0.056038] DMI not present or invalid. [ 0.058487] NET: Registered protocol family 16 [ 0.070240] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.077956] cpuidle: using governor menu [ 0.102729] vdd3p0: supplied by regulator-dummy [ 0.104125] cpu: supplied by regulator-dummy [ 0.106107] vddsoc: supplied by regulator-dummy [ 0.145587] No ATAGs? [ 0.145738] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.145785] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.156246] imx6ul-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e4000 debugfs directory [ 0.156970] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.169578] Serial: AMBA PL011 UART driver [ 0.253203] mxs-dma 1804000.dma-apbh: initialized [ 0.272909] vgaarb: loaded [ 0.276035] SCSI subsystem initialized [ 0.277646] usbcore: registered new interface driver usbfs [ 0.277837] usbcore: registered new interface driver hub [ 0.277992] usbcore: registered new device driver usb [ 0.282672] i2c i2c-0: IMX I2C adapter registered [ 0.282732] i2c i2c-0: can't use DMA, using PIO instead. [ 0.285592] i2c i2c-1: IMX I2C adapter registered [ 0.285651] i2c i2c-1: can't use DMA, using PIO instead. [ 0.287785] i2c i2c-2: IMX I2C adapter registered [ 0.287843] i2c i2c-2: can't use DMA, using PIO instead. [ 0.291924] pps_core: LinuxPPS API ver. 1 registered [ 0.291957] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.292051] PTP clock support registered [ 0.292727] EDAC MC: Ver: 3.0.0 [ 0.302408] clocksource: Switched to clocksource mxc_timer1 [ 0.542292] NET: Registered protocol family 2 [ 0.543201] IP idents hash table entries: 8192 (order: 4, 65536 bytes) [ 0.545525] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 8192 bytes) [ 0.545624] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.545767] TCP bind hash table entries: 4096 (order: 4, 114688 bytes) [ 0.546102] TCP: Hash tables configured (established 4096 bind 4096) [ 0.546399] UDP hash table entries: 256 (order: 2, 16384 bytes) [ 0.546497] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes) [ 0.547101] NET: Registered protocol family 1 [ 0.548860] RPC: Registered named UNIX socket transport module. [ 0.548902] RPC: Registered udp transport module. [ 0.548927] RPC: Registered tcp transport module. [ 0.548950] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.550314] Trying to unpack rootfs image as initramfs... [ 3.402051] Freeing initrd memory: 13016K [ 3.407687] Initialise system trusted keyrings [ 3.408493] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 3.439404] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.442650] NFS: Registering the id_resolver key type [ 3.442852] Key type id_resolver registered [ 3.442883] Key type id_legacy registered [ 3.443035] ntfs: driver 2.1.32 [Flags: R/O]. [ 3.451373] Key type asymmetric registered [ 3.451418] Asymmetric key parser 'x509' registered [ 3.451591] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 3.451627] io scheduler noop registered [ 3.451652] io scheduler deadline registered [ 3.453037] io scheduler cfq registered (default) [ 3.453077] io scheduler mq-deadline registered [ 3.453106] io scheduler kyber registered [ 3.516404] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 3.516696] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 3.517005] pwm-backlight backlight: Dropping the link to regulator.0 [ 3.548216] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 3.548282] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 3.768607] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.780297] SuperH (H)SCI(F) driver initialized [ 3.783889] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 60, base_baud = 5000000) is a IMX [ 3.786735] 21fc000.serial: ttymxc5 at MMIO 0x21fc000 (irq = 61, base_baud = 5000000) is a IMX [ 4.532559] console [ttymxc5] enabled [ 4.539945] msm_serial: driver initialized [ 4.544871] STMicroelectronics ASC driver initialized [ 4.554151] STM32 USART driver initialized [ 4.622209] brd: module loaded [ 4.654572] loop: module loaded [ 4.699793] CAN device driver interface [ 4.707015] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 4.715434] fec 20b4000.ethernet: 20b4000.ethernet supply phy not found, using dummy regulator [ 4.724359] fec 20b4000.ethernet: Linked as a consumer to regulator.0 [ 4.734577] pps pps0: new PPS source ptp0 [ 4.804199] fec 20b4000.ethernet eth0: registered PHC device 0 [ 4.814149] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 4.820020] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 4.826293] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 4.833360] igb: Copyright (c) 2007-2014 Intel Corporation. [ 4.855749] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 4.863455] usbcore: registered new interface driver pegasus [ 4.869351] usbcore: registered new interface driver asix [ 4.874946] usbcore: registered new interface driver ax88179_178a [ 4.881192] usbcore: registered new interface driver cdc_ether [ 4.887254] usbcore: registered new interface driver smsc75xx [ 4.893221] usbcore: registered new interface driver smsc95xx [ 4.899127] usbcore: registered new interface driver net1080 [ 4.904987] usbcore: registered new interface driver cdc_subset [ 4.911052] usbcore: registered new interface driver zaurus [ 4.916959] usbcore: registered new interface driver cdc_ncm [ 4.930790] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.937373] ehci-pci: EHCI PCI platform driver [ 4.942053] ehci-platform: EHCI generic platform driver [ 4.948186] ehci-orion: EHCI orion driver [ 4.953082] SPEAr-ehci: EHCI SPEAr driver [ 4.957696] ehci-st: EHCI STMicroelectronics driver [ 4.963213] ehci-exynos: EHCI EXYNOS driver [ 4.967989] ehci-atmel: EHCI Atmel driver [ 4.972774] tegra-ehci: Tegra EHCI driver [ 4.977454] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.983745] ohci-pci: OHCI PCI platform driver [ 4.988410] ohci-platform: OHCI generic platform driver [ 4.994487] SPEAr-ohci: OHCI SPEAr driver [ 4.999108] ohci-st: OHCI STMicroelectronics driver [ 5.004630] ohci-atmel: OHCI Atmel driver [ 5.011512] usbcore: registered new interface driver usb-storage [ 5.024147] imx_usb 2184000.usb: Linked as a consumer to regulator.7 [ 5.040753] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator [ 5.049229] imx_usb 2184200.usb: Linked as a consumer to regulator.0 [ 5.060771] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 5.065791] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 5.102567] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 5.110695] hub 1-0:1.0: USB hub found [ 5.114631] hub 1-0:1.0: 1 port detected [ 5.139969] i2c /dev entries driver [ 5.188068] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 5.209237] sdhci: Secure Digital Host Controller Interface driver [ 5.215469] sdhci: Copyright(c) Pierre Ossman [ 5.226322] Synopsys Designware Multimedia Card Interface Driver [ 5.238249] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.281558] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA [ 5.291755] sdhci-esdhc-imx 2194000.usdhc: Linked as a consumer to regulator.8 [ 5.352740] mmc0: new DDR MMC card at address 0001 [ 5.360412] mmcblk0: mmc0:0001 M62704 3.56 GiB [ 5.366572] mmcblk0boot0: mmc0:0001 M62704 partition 1 2.00 MiB [ 5.374191] mmcblk0boot1: mmc0:0001 M62704 partition 2 2.00 MiB [ 5.380771] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB, chardev (235:0) [ 5.390933] mmcblk0: p1 p2 [ 5.555341] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 5.585573] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 5.593193] usbcore: registered new interface driver usbhid [ 5.598800] usbhid: USB HID core driver [ 5.604520] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 5.624539] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 5.634953] NET: Registered protocol family 10 [ 5.645610] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 5.651239] Segment Routing with IPv6 [ 5.655305] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 5.665183] NET: Registered protocol family 17 [ 5.669734] can: controller area network core (rev 20170425 abi 9) [ 5.676242] NET: Registered protocol family 29 [ 5.680987] can: raw protocol (rev 20170425) [ 5.685312] can: broadcast manager protocol (rev 20170425 t) [ 5.691055] can: netlink gateway (rev 20170425) max_hops=1 [ 5.699201] Key type dns_resolver registered [ 5.708634] cpu cpu0: Linked as a consumer to regulator.2 [ 5.714624] cpu cpu0: Linked as a consumer to regulator.3 [ 5.725116] ThumbEE CPU extension supported. [ 5.729457] Registering SWP/SWPB emulation handler [ 5.736980] Loading compiled-in X.509 certificates [ 5.797094] mmc1: new high speed SDIO card at address 0001 [ 5.832106] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 5.840804] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 5.847775] pwm-backlight backlight: Dropping the link to regulator.0 [ 5.861342] imx_thermal tempmon: Industrial CPU temperature grade - max:105C critical:100C passive:95C [ 5.873839] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 5.882725] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 5.889682] pwm-backlight backlight: Dropping the link to regulator.0 [ 5.900087] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 5.908899] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 5.915917] pwm-backlight backlight: Dropping the link to regulator.0 [ 5.926176] hctosys: unable to open rtc device (rtc0) [ 5.941706] Freeing unused kernel memory: 2048K [ 5.946799] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 6.324900] udevd[101]: starting version 3.2.9 [ 6.331775] random: udevd: uninitialized urandom read (16 bytes read) [ 6.339209] random: udevd: uninitialized urandom read (16 bytes read) [ 6.346174] random: udevd: uninitialized urandom read (16 bytes read) [ 6.372970] udevd[101]: specified user 'tss' unknown [ 6.378384] udevd[101]: specified group 'tss' unknown [ 6.403054] udevd[102]: starting eudev-3.2.9 [ 9.148338] flexcan 2090000.flexcan: 2090000.flexcan supply xceiver not found, using dummy regulator [ 9.258984] flexcan 2090000.flexcan: Linked as a consumer to regulator.0 [ 9.284436] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=22) [ 9.294499] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 9.362926] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 9.369894] pwm-backlight backlight: Dropping the link to regulator.0 [ 9.472987] flexcan 2094000.flexcan: 2094000.flexcan supply xceiver not found, using dummy regulator [ 9.502971] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 9.522145] flexcan 2094000.flexcan: Linked as a consumer to regulator.0 [ 9.584448] flexcan 2094000.flexcan: device registered (reg_base=(ptrval), irq=23) [ 9.607484] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 9.648289] pwm-backlight backlight: Dropping the link to regulator.0 [ 9.691733] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 9.732110] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 9.751389] pwm-backlight backlight: Dropping the link to regulator.0 [ 10.071918] sgtl5000 1-000a: Linked as a consumer to regulator.4 [ 10.181811] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 10.183739] sgtl5000 1-000a: Linked as a consumer to regulator.5 [ 10.200670] sgtl5000 1-000a: sgtl5000 revision 0x11 [ 10.222684] sgtl5000 1-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 10.236379] [drm] No driver support for vblank timestamp query. [ 10.372254] OF: graph: no port node found in /soc/aips-bus@2100000/lcdif@21c8000 [ 10.379715] mxsfb 21c8000.lcdif: Failed to create outputs [ 10.398030] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 10.398237] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 10.398465] pwm-backlight backlight: Dropping the link to regulator.0 [ 10.591409] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 11.353668] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 11.360570] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 11.369239] cfg80211: failed to load regulatory.db [ 11.489162] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 11.521421] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 11.548125] pwm-backlight backlight: Dropping the link to regulator.0 [ 11.553520] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430a0-sdio for chip BCM43430/0 [ 11.599055] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 11.634150] pwm-backlight backlight: Linked as a consumer to regulator.0 [ 11.641119] pwm-backlight backlight: Dropping the link to regulator.0 [ 11.685282] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430a0-sdio.bin failed with error -2 [ 12.733067] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 done Saving random seed: [ 13.099498] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: [ 13.321328] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-829790/environment . /lava-829790/environment / # /lava-829790/bin/lava-test-runner /lava-829790/0 /lava-829790/bin/lava-test-runne /lava-829790/0 /bin/sh: /lava-829790/bin/lava-test-runne: not found / # [ 36.335447] VSD_3V3: disabling [ 36.338592] usb_otg_vbus: disabling