[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.101 (2 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 7989985/tftp-deploy-hsgtxoa_/kernel/zImage tftp 0x10000000 7989985/tftp-deploy-hsgtxoa_/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '7989985/tftp-deploy-hsgtxoa_/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 2.2 MiB/s done Bytes transferred = 8823296 (86a200 hex) => tftp 0x14000000 7989985/tftp-deploy-hsgtxoa_/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7989985/tftp-deploy-hsgtxoa_/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '7989985/tftp-deploy-hsgtxoa_/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################### 2.5 MiB/s done Bytes transferred = 13315262 (cb2cbe hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7989985/tftp-deploy-hsgtxoa_/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7989985/tftp-deploy-hsgtxoa_/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '7989985/tftp-deploy-hsgtxoa_/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.1 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x86a200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13315198 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.265-cip85-rt27 (KernelCI@build-j511275-arm-gcc-10-multi-v7-defconfig-preempt-rt-t7bjz) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Wed Nov 16 01:40:40 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') <6>[ 0.000000] bootconsole [ec_imx21] enabled <6>[ 0.000000] Memory policy: Data cache writealloc <6>[ 0.000000] efi: Getting EFI parameters from FDT: <6>[ 0.000000] efi: UEFI not found. <3>[ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring <6>[ 0.000000] cma: Reserved 64 MiB at 0x4c000000 <6>[ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 <5>[ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 938584K/1048576K available (12288K kernel code, 1636K rwdata, 4692K rodata, 2048K init, 406K bss, 44456K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. <6>[ 0.000000] No expedited grace period (rcu_normal_after_boot). <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000006] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.000018] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.003138] Console: colour dummy device 80x30 <6>[ 0.271159] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.271170] pid_max: default: 32768 minimum: 301 <6>[ 0.271329] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.271348] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.272071] CPU: Testing write buffer coherency: ok <6>[ 0.272100] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.272539] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.318122] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.325771] rcu: Hierarchical SRCU implementation. <6>[ 0.332982] EFI services will not be available. <6>[ 0.335301] smp: Bringing up secondary CPUs ... <6>[ 0.341059] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.341066] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.342553] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.342559] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.344026] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.344032] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.344178] smp: Brought up 1 node, 4 CPUs <6>[ 0.379358] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.385878] CPU: All CPU(s) started in SVC mode. <6>[ 0.391960] devtmpfs: initialized <6>[ 0.405654] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.411320] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.420852] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.430600] pinctrl core: initialized pinctrl subsystem <6>[ 0.435350] DMI not present or invalid. <6>[ 0.438255] NET: Registered protocol family 16 <6>[ 0.447686] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.455158] cpuidle: using governor menu <6>[ 0.456714] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.474891] vdd1p1: supplied by regulator-dummy <6>[ 0.477542] vdd3p0: supplied by regulator-dummy <6>[ 0.482325] vdd2p5: supplied by regulator-dummy <6>[ 0.487103] vddarm: supplied by regulator-dummy <6>[ 0.492141] vddpu: supplied by regulator-dummy <6>[ 0.496376] vddsoc: supplied by regulator-dummy <6>[ 0.519782] No ATAGs? <6>[ 0.519906] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.527848] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.538357] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.545312] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.558841] Serial: AMBA PL011 UART driver <6>[ 0.563349] console [pstore-1] enabled <6>[ 0.564728] pstore: Registered ramoops as persistent store backend <6>[ 0.570949] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.610665] mxs-dma 110000.dma-apbh: initialized <6>[ 0.622838] vgaarb: loaded <5>[ 0.624101] SCSI subsystem initialized <6>[ 0.627523] usbcore: registered new interface driver usbfs <6>[ 0.632771] usbcore: registered new interface driver hub <6>[ 0.638316] usbcore: registered new device driver usb <6>[ 0.645499] i2c i2c-0: IMX I2C adapter registered <6>[ 0.648543] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.655128] i2c i2c-1: IMX I2C adapter registered <6>[ 0.659067] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.665403] i2c i2c-2: IMX I2C adapter registered <6>[ 0.669594] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.677089] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.680374] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.689791] PTP clock support registered <6>[ 0.694271] EDAC MC: Ver: 3.0.0 <6>[ 0.701150] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.799391] NET: Registered protocol family 2 <6>[ 0.801691] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.809272] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.816184] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.823538] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) <6>[ 0.830604] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.837101] UDP hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.843087] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.849916] NET: Registered protocol family 1 <6>[ 0.854988] RPC: Registered named UNIX socket transport module. <6>[ 0.860412] RPC: Registered udp transport module. <6>[ 0.865373] RPC: Registered tcp transport module. <6>[ 0.870329] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.877666] Trying to unpack rootfs image as initramfs... <6>[ 2.108517] Freeing initrd memory: 13004K <4>[ 2.110354] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.117642] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.128486] Initialise system trusted keyrings <6>[ 2.130722] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.148317] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.152701] NFS: Registering the id_resolver key type <5>[ 2.156908] Key type id_resolver registered <5>[ 2.161313] Key type id_legacy registered <6>[ 2.165626] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.172941] Key type asymmetric registered <5>[ 2.174537] Asymmetric key parser 'x509' registered <6>[ 2.179783] bounce: pool size: 64 pages <6>[ 2.183800] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 2.191417] io scheduler noop registered <6>[ 2.195588] io scheduler deadline registered <6>[ 2.200458] io scheduler cfq registered (default) <6>[ 2.205075] io scheduler mq-deadline registered <6>[ 2.209858] io scheduler kyber registered <6>[ 2.243311] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.247890] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.255061] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.262319] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.282719] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.289631] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <4>[ 2.296382] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.296463] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.296526] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.296658] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 2.296811] PU : no governor for states <6>[ 2.296829] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 2.375633] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.384293] SuperH (H)SCI(F) driver initialized <6>[ 2.387522] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 2.396334] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 2.406893] console [ttymxc1] enabled <6>[ 2.406893] console [ttymxc1] enabled <6>[ 2.411883] bootconsole [ec_imx21] disabled <6>[ 2.411883] bootconsole [ec_imx21] disabled <6>[ 2.422505] msm_serial: driver initialized <6>[ 2.428279] STMicroelectronics ASC driver initialized <6>[ 2.435421] STM32 USART driver initialized <4>[ 2.453230] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.461959] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.468975] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.475772] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.484828] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.492011] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.510987] brd: module loaded <6>[ 2.528496] loop: module loaded <6>[ 2.536088] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.544288] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.552570] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.561022] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.571302] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.578566] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.587633] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.598827] scsi host0: ahci-imx <6>[ 2.603100] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.626016] CAN device driver interface <6>[ 2.631774] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.639076] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.648059] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.657500] pps pps0: new PPS source ptp0 <6>[ 2.691895] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.699581] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.705689] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.711973] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.719205] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.732536] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.740261] usbcore: registered new interface driver pegasus <6>[ 2.746272] usbcore: registered new interface driver asix <6>[ 2.751995] usbcore: registered new interface driver ax88179_178a <6>[ 2.758405] usbcore: registered new interface driver cdc_ether <6>[ 2.764578] usbcore: registered new interface driver smsc75xx <6>[ 2.770659] usbcore: registered new interface driver smsc95xx <6>[ 2.776730] usbcore: registered new interface driver net1080 <6>[ 2.782724] usbcore: registered new interface driver cdc_subset <6>[ 2.788962] usbcore: registered new interface driver zaurus <6>[ 2.794902] usbcore: registered new interface driver cdc_ncm <6>[ 2.804664] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.811468] ehci-pci: EHCI PCI platform driver <6>[ 2.816247] ehci-platform: EHCI generic platform driver <6>[ 2.822127] ehci-orion: EHCI orion driver <6>[ 2.826697] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.831303] ehci-st: EHCI STMicroelectronics driver <6>[ 2.836712] ehci-exynos: EHCI EXYNOS driver <6>[ 2.841460] ehci-atmel: EHCI Atmel driver <6>[ 2.845986] tegra-ehci: Tegra EHCI driver <6>[ 2.850544] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.857020] ohci-pci: OHCI PCI platform driver <6>[ 2.861800] ohci-platform: OHCI generic platform driver <6>[ 2.867633] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.872201] ohci-st: OHCI STMicroelectronics driver <6>[ 2.877612] ohci-atmel: OHCI Atmel driver <6>[ 2.883131] usbcore: registered new interface driver usb-storage <6>[ 2.892341] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.905284] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.915722] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.920900] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.942778] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.948486] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.951223] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.952195] hub 1-0:1.0: USB hub found <6>[ 2.952243] hub 1-0:1.0: 1 port detected <6>[ 2.960975] i2c /dev entries driver <6>[ 2.972647] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <3>[ 2.975734] imx_thermal tempmon: invalid sensor calibration data <3>[ 2.975743] imx_thermal tempmon: failed to init from from fsl,tempmon-data <4>[ 2.975764] imx_thermal: probe of tempmon failed with error -22 <6>[ 2.980143] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.987218] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.987222] sdhci: Copyright(c) Pierre Ossman <6>[ 2.990007] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.992626] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.993589] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.993624] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.993764] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.026028] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 3.026650] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 3.026797] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.061605] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 3.069181] mmc0: new high speed SDHC card at address 0001 <6>[ 3.071062] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 3.074158] usbcore: registered new interface driver usbhid <6>[ 3.074163] usbhid: USB HID core driver <6>[ 3.082354] NET: Registered protocol family 10 <6>[ 3.083876] Segment Routing with IPv6 <6>[ 3.083962] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <4>[ 3.084343] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.084350] GPT:29296874 != 30965759 <4>[ 3.084354] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.084358] GPT:29296874 != 30965759 <4>[ 3.084361] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.084416] mmcblk0: p1 p2 p3 <6>[ 3.084781] NET: Registered protocol family 17 <6>[ 3.084802] can: controller area network core (rev 20170425 abi 9) <6>[ 3.084930] NET: Registered protocol family 29 <6>[ 3.084941] can: raw protocol (rev 20170425) <6>[ 3.084949] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.084965] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 3.085737] Key type dns_resolver registered <6>[ 3.086927] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 3.087020] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 3.087138] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 3.088334] ThumbEE CPU extension supported. <5>[ 3.088352] Registering SWP/SWPB emulation handler <5>[ 3.089077] Loading compiled-in X.509 certificates <6>[ 3.091125] pstore: Using compression: deflate <6>[ 3.121748] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.121869] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.124027] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.124139] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.126338] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.126425] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.126549] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.128363] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.128445] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.128566] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.130099] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.130201] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.132112] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.132216] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.134340] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.134427] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.134551] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.136343] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.136425] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.136542] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.140288] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.141408] hctosys: unable to open rtc device (rtc0) <6>[ 3.141674] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.141782] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.144185] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.144331] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.147497] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.147626] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.147796] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.150385] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.150532] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.150696] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.241207] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.252021] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 3.252218] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 3.442455] hub 1-1:1.0: USB hub found <6>[ 3.442630] hub 1-1:1.0: 3 ports detected <6>[ 3.444860] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.444980] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.446905] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.447010] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.449144] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.449237] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.449356] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.451295] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.451384] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.451502] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.352115] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 5.361323] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.391409] Sending DHCP requests ., OK <6>[ 5.555499] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.101 <6>[ 5.563882] IP-Config: Complete: <6>[ 5.567407] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.101.101, mask=255.255.255.0, gw=192.168.101.1 <6>[ 5.578221] host=imx6q-sabrelite-cbg-2, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 5.587276] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 5.587281] nameserver0=192.168.101.1 <6>[ 5.606123] Freeing unused kernel memory: 2048K <6>[ 5.611422] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.793637] udevd[140]: starting version 3.2.9 <5>[ 5.799600] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.806706] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.813555] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.829941] udevd[140]: specified user 'tss' unknown <27>[ 5.835453] udevd[140]: specified group 'tss' unknown <30>[ 5.844094] udevd[141]: starting eudev-3.2.9 <6>[ 6.943069] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.950523] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.964202] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.971742] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.988079] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.997611] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.998385] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.998523] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.000986] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.001083] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.001363] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.003056] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.003164] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.004855] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.005772] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.006739] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.006851] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.009191] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.009299] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.009426] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.011369] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.012068] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.012203] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.015084] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.015191] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.149866] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.170093] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.176918] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.202294] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.227253] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.233638] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.248631] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.258042] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.265587] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.283523] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.292437] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.299487] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.309035] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.318126] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.325355] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.335657] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.343121] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.612144] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.619673] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.632919] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.642105] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.649139] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.659582] sgtl5000 0-000a: Linked as a consumer to regulator.7 <4>[ 7.666093] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.666542] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.668444] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.686627] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.689369] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.701701] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.710567] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.718026] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.751096] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.762084] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.774061] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.783849] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.791751] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.804135] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.815371] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.822613] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.836959] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.844433] pwm-backlight backlight-lcd: Dropping the link to regulator.8 done Saving random seed: <5>[ 8.154612] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.293500] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7989985/environment . /lava-7989985/environment / # /lava-7989985/bin/lava-test-runner /lava-7989985/0 /lava-7989985/bin/lava-test-runner /lava-7989985/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-7989985/0/tests/0_dmesg + cat uuid + UUID=7989985_1.5.2.4.1 <8>[ 8.908836] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.971935] <8>[ 9.018912] <8>[ 9.066133] + set +x <8>[ 9.076317] / ## export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7989985/environment / # . /lava-7989985/environment/lava-7989985/bin/lava-test-runner /lava-7989985/1 / # /lava-7989985/bin/lava-test-runner /lava-7989985/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-7989985/1/tests/1_bootrr + cat uuid + UUID=7989985_1.5.2.4.5 <8>[ 9.596019] + set +x + export 'PATH=/opt/bootrr/helpers:/lava-7989985/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7989985/1/../bin/lava-test-case <8>[ 10.680340] /lava-7989985/1/../bin/lava-test-case <8>[ 10.727183] /lava-7989985/1/../bin/lava-test-case <8>[ 10.766163] + set +x <8>[ 10.787535] / #