connecting to NetworkSerialPort(target=Target(name='dove-cubox-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4015, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4015 connected to 10.8.254.5 (port 4015) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2020.06.0-00092-gc130f9ac29 #2 Fri Jul 3 17:13:59 CEST 2020 Board: Marvell Dove SoC: Marvell 0510 rev 7 mdio_bus: miibus0: probed [33mWARNING:[0m m25p80 spi-flash@00: found n25q032, expected w25q32 m25p80 spi-flash@00: n25q032 (4096 Kbytes) dove-sdhci f1092000.sdio-host@92000.of: registered as mci0 mci0: detected SD card version 2.0 mci0: registered disk0 malloc space: 0x1fefe1a0 -> 0x3fdfc33f (size 511 MiB) envfs: no envfs (magic mismatch) - envfs never written? [?25h Hit m for menu or any to stop autoboot: 3 [1;32mbarebox@[1;36mMarvell Dove:/[0m bootm -v -r /mnt/tftp/882610/tftp-deploy-ssc0344c/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/882610/tftp-deploy-ssc0344c/dtb/dove-cubox.dtb /mnt/tftp/882610/tftp-deploy-ssc0344c/kernel/zImage -a 0x05000000 -L 0x04000000 [1;32mbarebox@[1;36mMarvell Dove:/[0m bootm -v -r /mnt/tftp/882610/tftp-deploy-ssc0344c/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/882610/tftp-deploy-ssc0344c/dtb/dove-cubox.dtb /mnt/tftp/882610/tftp-deploy-ssc0344c/kernel/zImage -a 0x05000000 -L 0x04000000 eth0: 1000Mbps full duplex link detected [33mWARNING:[0m eth0: No MAC address set. Using random address 16:1b:61:88:d0:9d T eth0: DHCP client bound to address 10.8.254.56 Loading ARM Linux zImage '/mnt/tftp/882610/tftp-deploy-ssc0344c/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler Loaded initrd GZIP compressed '/mnt/tftp/882610/tftp-deploy-ssc0344c/ramdisk/ramdisk.cpio.gz' initrd is at 0x04000000-0x04cb8345 Loading devicetree from '/mnt/tftp/882610/tftp-deploy-ssc0344c/dtb/dove-cubox.dtb' commandline: console=ttyS0,115200n8 earlyprintk Starting kernel at 0x05000000, initrd at 0x04000000, oftree at 0x04cb9000... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.269-cip88-rt28 (KernelCI@build-j877150-arm-gcc-10-defconfig-preempt-rt-tbxj8) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Wed Jan 18 20:47:23 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [560f5815] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: SolidRun CuBox [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x3c000000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 938832K/1048576K available (12288K kernel code, 1636K rwdata, 4692K rodata, 2048K init, 406K bss, 44208K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] No expedited grace period (rcu_normal_after_boot). [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000008] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns [ 0.000044] Switching to timer-based delay loop, resolution 6ns [ 0.001653] Console: colour dummy device 80x30 [ 0.001839] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.001853] pid_max: default: 32768 minimum: 301 [ 0.002042] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.002064] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003055] CPU: Testing write buffer coherency: ok [ 0.003554] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.004985] Setting up static identity map for 0x300000 - 0x3000a0 [ 0.006256] rcu: Hierarchical SRCU implementation. [ 0.009346] EFI services will not be available. [ 0.009664] smp: Bringing up secondary CPUs ... [ 0.009685] smp: Brought up 1 node, 1 CPU [ 0.009699] SMP: Total of 1 processors activated (333.33 BogoMIPS). [ 0.009709] CPU: All CPU(s) started in SVC mode. [ 0.010747] devtmpfs: initialized [ 0.017679] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5 [ 0.018391] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.018431] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.023913] pinctrl core: initialized pinctrl subsystem [ 0.026343] DMI not present or invalid. [ 0.027502] NET: Registered protocol family 16 [ 0.033912] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.037458] cpuidle: using governor menu [ 0.037792] Dove 88AP510 SoC [ 0.037822] Tauros2: Disabling L2 prefetch. [ 0.037834] Tauros2: Disabling burst8 line fill. [ 0.037843] Tauros2: Enabling L2 cache. [ 0.037853] Tauros2: L2 cache support initialised in ARMv7 mode. [ 0.038328] No ATAGs? [ 0.038337] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.041031] Serial: AMBA PL011 UART driver [ 0.084441] vgaarb: loaded [ 0.085503] SCSI subsystem initialized [ 0.086151] usbcore: registered new interface driver usbfs [ 0.086237] usbcore: registered new interface driver hub [ 0.086299] usbcore: registered new device driver usb [ 0.087976] pps_core: LinuxPPS API ver. 1 registered [ 0.087988] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.088026] PTP clock support registered [ 0.088235] EDAC MC: Ver: 3.0.0 [ 0.091621] clocksource: Switched to clocksource orion_clocksource [ 0.205300] NET: Registered protocol family 2 [ 0.205679] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.206886] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes) [ 0.206944] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.207051] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) [ 0.207400] TCP: Hash tables configured (established 8192 bind 8192) [ 0.207554] UDP hash table entries: 512 (order: 3, 32768 bytes) [ 0.207619] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) [ 0.207850] NET: Registered protocol family 1 [ 0.208544] RPC: Registered named UNIX socket transport module. [ 0.208559] RPC: Registered udp transport module. [ 0.208569] RPC: Registered tcp transport module. [ 0.208579] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.209076] Trying to unpack rootfs image as initramfs... [ 1.360796] Freeing initrd memory: 13028K [ 1.363227] Initialise system trusted keyrings [ 1.363567] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.378360] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.379703] NFS: Registering the id_resolver key type [ 1.379757] Key type id_resolver registered [ 1.379769] Key type id_legacy registered [ 1.379829] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.383192] Key type asymmetric registered [ 1.383208] Asymmetric key parser 'x509' registered [ 1.383391] bounce: pool size: 64 pages [ 1.383448] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.383462] io scheduler noop registered [ 1.383474] io scheduler deadline registered [ 1.383916] io scheduler cfq registered (default) [ 1.383930] io scheduler mq-deadline registered [ 1.383942] io scheduler kyber registered [ 1.392776] dove-pinctrl f10d0200.pin-ctrl: falling back to hardcoded PMU resource [ 1.393053] dove-pinctrl f10d0200.pin-ctrl: [Firmware Bug]: Missing pinctrl regs in DTB. Please update your firmware. [ 1.393867] dove-pinctrl f10d0200.pin-ctrl: registered pinctrl driver [ 1.410632] mv_xor f1060800.dma-engine: Marvell shared XOR driver [ 1.473487] mv_xor f1060800.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.473804] mv_xor f1060900.dma-engine: Marvell shared XOR driver [ 1.533483] mv_xor f1060900.dma-engine: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 1.618114] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.623033] console [ttyS0] disabled [ 1.623132] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 21, base_baud = 10416666) is a 16550A [ 2.313953] console [ttyS0] enabled [ 2.318506] SuperH (H)SCI(F) driver initialized [ 2.324058] msm_serial: driver initialized [ 2.328335] STMicroelectronics ASC driver initialized [ 2.334434] STM32 USART driver initialized [ 2.360749] brd: module loaded [ 2.376169] loop: module loaded [ 2.383041] sata_mv f10a0000.sata-host: slots 32 ports 1 [ 2.391338] scsi host0: sata_mv [ 2.395117] ata1: SATA max UDMA/133 irq 30 [ 2.405030] m25p80 spi0.0: found n25q032, expected w25q32 [ 2.410607] m25p80 spi0.0: n25q032 (4096 Kbytes) [ 2.415237] 2 fixed-partitions partitions found on MTD device spi0.0 [ 2.421560] Creating 2 MTD partitions on \"spi0.0\": [ 2.426340] 0x000000000000-0x000000200000 : \"barebox\" [ 2.432761] 0x000000200000-0x000000220000 : \"env\" [ 2.444643] CAN device driver interface [ 2.449397] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.456171] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.461981] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.467976] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.474914] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.481281] [Firmware Warn]: /mbus/internal-regs/mdio-bus@72004/ethernet-phy: Whitelisted compatible string. Please remove [ 2.526861] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 2.536038] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set [ 2.642957] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 16:1b:61:88:d0:9d [ 2.655707] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.663159] usbcore: registered new interface driver pegasus [ 2.668890] usbcore: registered new interface driver asix [ 2.674342] usbcore: registered new interface driver ax88179_178a [ 2.680489] usbcore: registered new interface driver cdc_ether [ 2.686395] usbcore: registered new interface driver smsc75xx [ 2.692195] usbcore: registered new interface driver smsc95xx [ 2.697999] usbcore: registered new interface driver net1080 [ 2.703707] usbcore: registered new interface driver cdc_subset [ 2.709670] usbcore: registered new interface driver zaurus [ 2.715352] usbcore: registered new interface driver cdc_ncm [ 2.723367] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.729904] ata1: SATA link down (SStatus 0 SControl F300) [ 2.735439] ehci-pci: EHCI PCI platform driver [ 2.739934] ehci-platform: EHCI generic platform driver [ 2.745353] ehci-orion: EHCI orion driver [ 2.749649] orion-ehci f1050000.usb-host: EHCI Host Controller [ 2.755496] orion-ehci f1050000.usb-host: new USB bus registered, assigned bus number 1 [ 2.764053] orion-ehci f1050000.usb-host: irq 25, io mem 0xf1050000 [ 2.791678] orion-ehci f1050000.usb-host: USB 2.0 started, EHCI 1.00 [ 2.799126] hub 1-0:1.0: USB hub found [ 2.802922] hub 1-0:1.0: 1 port detected [ 2.807576] orion-ehci f1051000.usb-host: EHCI Host Controller [ 2.813442] orion-ehci f1051000.usb-host: new USB bus registered, assigned bus number 2 [ 2.821964] orion-ehci f1051000.usb-host: irq 26, io mem 0xf1051000 [ 2.851669] orion-ehci f1051000.usb-host: USB 2.0 started, EHCI 1.00 [ 2.859027] hub 2-0:1.0: USB hub found [ 2.862810] hub 2-0:1.0: 1 port detected [ 2.867414] SPEAr-ehci: EHCI SPEAr driver [ 2.871741] ehci-st: EHCI STMicroelectronics driver [ 2.876778] ehci-exynos: EHCI EXYNOS driver [ 2.881106] ehci-atmel: EHCI Atmel driver [ 2.885284] tegra-ehci: Tegra EHCI driver [ 2.889462] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.896454] ohci-pci: OHCI PCI platform driver [ 2.900961] ohci-platform: OHCI generic platform driver [ 2.906367] SPEAr-ohci: OHCI SPEAr driver [ 2.910523] ohci-st: OHCI STMicroelectronics driver [ 2.915547] ohci-atmel: OHCI Atmel driver [ 2.920393] usbcore: registered new interface driver usb-storage [ 2.931215] rtc-mv f10d8500.real-time-clock: rtc core: registered f10d8500.real-time-clock as rtc0 [ 2.942386] i2c /dev entries driver [ 2.951438] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.956743] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.962039] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.974457] orion_wdt: Initial timeout 25 sec [ 2.983658] sdhci: Secure Digital Host Controller Interface driver [ 2.989813] sdhci: Copyright(c) Pierre Ossman [ 2.995805] Synopsys Designware Multimedia Card Interface Driver [ 3.003308] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.009683] mmc0 bounce up to 128 segments into one, max segment size 65536 bytes [ 3.043014] mmc0: SDHCI controller on f1092000.sdio-host [f1092000.sdio-host] using DMA [ 3.055062] usbcore: registered new interface driver usbhid [ 3.060640] usbhid: USB HID core driver [ 3.070399] NET: Registered protocol family 10 [ 3.076566] Segment Routing with IPv6 [ 3.080309] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.087442] NET: Registered protocol family 17 [ 3.092021] can: controller area network core (rev 20170425 abi 9) [ 3.096877] mmc0: new high speed SD card at address 59b4 [ 3.102682] mmcblk0: mmc0:59b4 USD 1.87 GiB [ 3.104472] mmcblk0: p1 [ 3.114945] NET: Registered protocol family 29 [ 3.119379] can: raw protocol (rev 20170425) [ 3.123659] can: broadcast manager protocol (rev 20170425 t) [ 3.129312] can: netlink gateway (rev 20170425) max_hops=1 [ 3.135375] Key type dns_resolver registered [ 3.139707] ThumbEE CPU extension supported. [ 3.143977] Registering SWP/SWPB emulation handler [ 3.148747] PJ4 iWMMXt v2 coprocessor enabled. [ 3.153996] Loading compiled-in X.509 certificates [ 3.165943] rtc-mv f10d8500.real-time-clock: setting system clock to 2022-12-02 02:49:12 UTC (1669949352) [ 3.182388] Freeing unused kernel memory: 2048K [ 3.189213] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 3.387372] udevd[99]: starting version 3.2.9 [ 3.393107] random: udevd: uninitialized urandom read (16 bytes read) [ 3.399912] random: udevd: uninitialized urandom read (16 bytes read) [ 3.406941] random: udevd: uninitialized urandom read (16 bytes read) [ 3.424430] udevd[99]: specified user 'tss' unknown [ 3.429462] udevd[99]: specified group 'tss' unknown [ 3.440349] udevd[100]: starting eudev-3.2.9 [ 4.858955] marvell-cesa f1030000.crypto-engine: CESA device successfully registered [ 4.988796] etnaviv etnaviv: bound f1840000.gpu (ops gpu_ops [etnaviv]) [ 5.001237] etnaviv-gpu f1840000.gpu: model: GC600, revision: 19 [ 5.136932] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 done Saving random seed: [ 5.991032] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: [ 6.109814] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-882610/environment . /lava-882610/environment / # /lava-882610/bin/lava-test-runner /lava-882610/0 /lava-882610/bin/lava-test-runner /lava-882610/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-882610/0/tests/0_dmesg + cat uuid + UUID=882610_1.5.[ 6.704308] 2.3.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 6.759829] [ 6.810732] [ 6.862115] + set +x [ 6.872684] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-882610/environment / # . /lava-882610/environment/lava-882610/bin/lava-test-runner /lava-882610/1 / # /lava-882610/bin/lava-test-runner /lava-882610/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-882610/1/tests/1_bootrr + cat uuid + UUID=882610_1.5.[ 7.368247] 2.3.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-882610/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-882610/1/../bin/lava-test-case [ 7.434144] /lava-882610/1/../bin/lava-test-case [ 7.482512] /lava-882610/1/../bin/lava-test-case [ 7.511582] + set +x [ 7.533960] / #