Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3009 device /dev/ttyimx7d-sdb-2 [115200 N81] (Debian GNU/Linux) U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 26C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.166 (1409 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1140208/tftp-deploy-68tvaexz/kernel/zImage tftp 0x80800000 1140208/tftp-deploy-68tvaexz/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1140208/tftp-deploy-68tvaexz/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 10.2 MiB/s done Bytes transferred = 8513544 (81e808 hex) => tftp 0x86800000 1140208/tftp-deploy-68tvaexz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1140208/tftp-deploy-68tvaexz/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1140208/tftp-deploy-68tvaexz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 11.1 MiB/s done Bytes transferred = 9268003 (8d6b23 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1140208/tftp-deploy-68tvaexz/dtb/imx7d-sdb.dtb tftp 0x83000000 1140208/tftp-deploy-68tvaexz/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1140208/tftp-deploy-68tvaexz/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 415 KiB/s done Bytes transferred = 33576 (8328 hex) =>setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x81e808 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9267939 Bytes = 8.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300b327 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.269-cip88-rt28 (KernelCI@build-j877155-arm-gcc-10-imx-v6-v7-defconfig-svxzb) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Jan 18 20:43:37 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] percpu: Embedded 17 pages/cpu s38184 r8192 d23256 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939796K/1048576K available (11264K kernel code, 880K rwdata, 3616K rodata, 1024K init, 7651K bss, 43244K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 881 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7652 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000009] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008290] Switching to timer-based delay loop, resolution 125ns <6>[ 0.015203] Switching to timer-based delay loop, resolution 41ns <6>[ 0.020981] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029117] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.040946] Console: colour dummy device 80x30 <4>[ 0.043726] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.051809] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.056147] ... MAX_LOCK_DEPTH: 48 <4>[ 0.060609] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.065275] ... CLASSHASH_SIZE: 4096 <4>[ 0.069884] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.074609] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.079362] ... CHAINHASH_SIZE: 32768 <4>[ 0.084060] memory used by lock dependency info: 4655 kB <4>[ 0.089773] per task-struct memory footprint: 1536 bytes <6>[ 0.095506] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.106145] pid_max: default: 32768 minimum: 301 <6>[ 0.111432] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.117973] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.128042] CPU: Testing write buffer coherency: ok <6>[ 0.131934] CPU0: update cpu_capacity 1024 <6>[ 0.134814] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.143140] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.148142] rcu: Hierarchical SRCU implementation. <6>[ 0.155172] smp: Bringing up secondary CPUs ... <6>[ 0.160291] smp: Brought up 1 node, 1 CPU <6>[ 0.161765] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.168353] CPU: All CPU(s) started in SVC mode. <6>[ 0.176201] devtmpfs: initialized <6>[ 0.204611] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.210541] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.220027] futex hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.229162] pinctrl core: initialized pinctrl subsystem <6>[ 0.237944] NET: Registered protocol family 16 <6>[ 0.265037] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.273415] cpuidle: using governor menu <6>[ 0.276322] No ATAGs? <6>[ 0.276589] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.285732] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.304793] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <4>[ 0.311324] imx7d-pinctrl 30330000.iomuxc: Failed to create dummy-iomuxc-gpr@30340000 debugfs directory <6>[ 0.320306] imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver <6>[ 0.329176] vdd1p0d: Bringing 0uV into 800000-800000uV <6>[ 0.332406] vdd1p0d: supplied by regulator-dummy <6>[ 0.338283] vdd1p2: supplied by regulator-dummy <6>[ 0.439953] mxs-dma 33000000.dma-apbh: initialized <6>[ 0.450158] vgaarb: loaded <5>[ 0.451468] SCSI subsystem initialized <6>[ 0.455801] usbcore: registered new interface driver usbfs <6>[ 0.460279] usbcore: registered new interface driver hub <6>[ 0.465935] usbcore: registered new device driver usb <4>[ 0.471445] usb_phy_generic usbphynop1: usbphynop1 supply vcc not found, using dummy regulator <6>[ 0.480467] usb_phy_generic usbphynop1: Linked as a consumer to regulator.0 <4>[ 0.487608] usb_phy_generic usbphynop3: usbphynop3 supply vcc not found, using dummy regulator <6>[ 0.496463] usb_phy_generic usbphynop3: Linked as a consumer to regulator.0 <4>[ 0.504000] usb_phy_generic usbphynop2: usbphynop2 supply vcc not found, using dummy regulator <6>[ 0.512615] usb_phy_generic usbphynop2: Linked as a consumer to regulator.0 <6>[ 0.523100] i2c i2c-0: IMX I2C adapter registered <6>[ 0.525261] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.532802] i2c i2c-1: IMX I2C adapter registered <6>[ 0.535845] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.543204] i2c i2c-2: IMX I2C adapter registered <6>[ 0.546431] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.553733] i2c i2c-3: IMX I2C adapter registered <6>[ 0.557018] i2c i2c-3: can't use DMA, using PIO instead. <6>[ 0.563131] media: Linux media interface: v0.10 <6>[ 0.567519] videodev: Linux video capture interface: v2.00 <6>[ 0.573730] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.578440] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.588002] PTP clock support registered <6>[ 0.592972] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.601471] Bluetooth: Core ver 2.22 <6>[ 0.602574] NET: Registered protocol family 31 <6>[ 0.607198] Bluetooth: HCI device and connection manager initialized <6>[ 0.613998] Bluetooth: HCI socket layer initialized <6>[ 0.619036] Bluetooth: L2CAP socket layer initialized <6>[ 0.624618] Bluetooth: SCO socket layer initialized <6>[ 0.631805] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.905190] VFS: Disk quotas dquot_6.6.0 <6>[ 0.906698] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 0.941953] NET: Registered protocol family 2 <6>[ 0.944248] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.953473] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.958910] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.966538] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.974319] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.980399] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.986263] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.993175] NET: Registered protocol family 1 <6>[ 0.999144] RPC: Registered named UNIX socket transport module. <6>[ 1.003431] RPC: Registered udp transport module. <6>[ 1.008323] RPC: Registered tcp transport module. <6>[ 1.013363] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.022817] Trying to unpack rootfs image as initramfs... <6>[ 1.998456] Freeing initrd memory: 9052K <6>[ 2.002416] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 2.013317] Initialise system trusted keyrings <6>[ 2.016047] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <5>[ 2.042635] NFS: Registering the id_resolver key type <5>[ 2.045269] Key type id_resolver registered <5>[ 2.049608] Key type id_legacy registered <6>[ 2.054176] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. <6>[ 2.062087] fuse init (API version 7.27) <5>[ 2.080078] Key type asymmetric registered <5>[ 2.081866] Asymmetric key parser 'x509' registered <6>[ 2.087180] bounce: pool size: 64 pages <6>[ 2.090997] io scheduler noop registered <6>[ 2.095168] io scheduler deadline registered <6>[ 2.100511] io scheduler cfq registered (default) <6>[ 2.104711] io scheduler mq-deadline registered <6>[ 2.109437] io scheduler kyber registered <4>[ 2.121544] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 2.128076] pwm-backlight backlight: Linked as a consumer to regulator.0 <4>[ 2.147344] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <4>[ 2.157428] imx7-pgc imx7-pgc-domain.1: DMA mask not set <6>[ 2.160512] imx7-pgc imx7-pgc-domain.1: Linked as a consumer to regulator.1 <6>[ 2.168010] imx-sdma 30bd0000.sdma: external firmware not found, using ROM firmware <6>[ 2.178682] pfuze100-regulator 0-0008: Full layer: 1, Metal layer: 1 <6>[ 2.183508] pfuze100-regulator 0-0008: FAB: 0, FIN: 0 <6>[ 2.187824] pfuze100-regulator 0-0008: pfuze3000 found. <6>[ 2.219812] VLDO4: Bringing 3300000uV into 2800000-2800000uV <4>[ 2.225392] reset_imx7 30390000.src: Failed to create dummy-src@30390000 debugfs�O��<6>[ 2.235431] console [ttymxc0] enabled <6>[ 2.235431] console [ttymxc0] enabled <6>[ 2.240466] bootconsole [ec_imx6q0] disabled <6>[ 2.240466] bootconsole [ec_imx6q0] disabled <6>[ 2.253053] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 57, base_baud = 15000000) is a IMX <6>[ 2.274648] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 2.281572] [drm] No driver support for vblank timestamp query. <3>[ 2.288333] mxsfb 30730000.lcdif: Failed to create outputs <6>[ 2.324414] brd: module loaded <6>[ 2.358139] loop: module loaded <3>[ 2.375759] spi_imx 30840000.ecspi: dma setup error -19, use pio <6>[ 2.383696] spi_imx 30840000.ecspi: probed <6>[ 2.391320] CAN device driver interface <6>[ 2.396497] flexcan 30a10000.can: Linked as a consumer to regulator.7 <6>[ 2.405284] flexcan 30a10000.can: device registered (reg_base=(ptrval), irq=52) <4>[ 2.417476] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 2.426928] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.437922] pps pps0: new PPS source ptp0 <6>[ 2.510231] fec 30be0000.ethernet eth0: registered PHC device 0 <4>[ 2.519745] fec 30bf0000.ethernet: 30bf0000.ethernet supply phy not found, using dummy regulator <6>[ 2.529296] fec 30bf0000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.537422] pps pps1: new PPS source ptp1 <3>[ 2.543470] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 2.550602] fec 30bf0000.ethernet: Using random MAC address: 6e:47:56:90:06:42 <6>[ 3.473071] fec 30bf0000.ethernet eth1: registered PHC device 1 <6>[ 3.480924] usbcore: registered new interface driver asix <6>[ 3.486976] usbcore: registered new interface driver ax88179_178a <6>[ 3.493687] usbcore: registered new interface driver cdc_ether <6>[ 3.499925] usbcore: registered new interface driver net1080 <6>[ 3.506142] usbcore: registered new interface driver cdc_subset <6>[ 3.512609] usbcore: registered new interface driver zaurus <6>[ 3.518659] usbcore: registered new interface driver cdc_ncm <6>[ 3.524656] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.531463] ehci-pci: EHCI PCI platform driver <6>[ 3.536338] ehci-mxc: Freescale On-Chip EHCI Host driver <6>[ 3.542811] usbcore: registered new interface driver usb-storage <6>[ 3.553409] imx_usb 30b10000.usb: Linked as a consumer to regulator.3 <6>[ 3.569028] imx_usb 30b20000.usb: Linked as a consumer to regulator.4 <6>[ 3.579067] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.584784] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.621861] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.632558] hub 1-0:1.0: USB hub found <6>[ 3.636868] hub 1-0:1.0: 1 port detected <6>[ 3.648514] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc/30000000.aips-bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 <4>[ 3.664250] ads7846 spi2.0: spi2.0 supply vcc not found, using dummy regulator <6>[ 3.674115] ads7846 spi2.0: Linked as a consumer to regulator.0 <6>[ 3.682224] ads7846 spi2.0: touchscreen, irq 135 <6>[ 3.689429] input: ADS7846 Touchscreen as /devices/platform/soc/30800000.aips-bus/30800000.spba-bus/30840000.ecspi/spi_master/spi2/spi2.0/input/input1 <6>[ 3.710084] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 <6>[ 3.716993] i2c /dev entries driver <6>[ 3.730279] imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.737376] Bluetooth: HCI UART driver ver 2.3 <6>[ 3.742171] Bluetooth: HCI UART protocol H4 registered <6>[ 3.748121] Bluetooth: HCI UART protocol LL registered <6>[ 3.754861] cpu cpu0: Linked as a consumer to regulator.8 <6>[ 3.761010] cpu cpu0: Dropping the link to regulator.8 <6>[ 3.769366] cpu cpu0: Linked as a consumer to regulator.8 <6>[ 3.780953] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.787784] sdhci: Copyright(c) Pierre Ossman <6>[ 3.792512] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.803803] sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO <6>[ 3.809370] sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO <6>[ 3.850885] mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA <6>[ 3.862523] sdhci-esdhc-imx 30b50000.usdhc: Linked as a consumer to regulator.6 <6>[ 3.912870] mmc0: new high speed SDHC card at address aaaa <6>[ 3.923299] mmcblk0: mmc0:aaaa SA16G 14.8 GiB <6>[ 3.935639] mmcblk0: p1 p2 <6>[ 4.123585] mmc1: SDHCI controller on 30b50000.usdhc [30b50000.usdhc] using ADMA <6>[ 4.169539] mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA <4>[ 4.177979] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 4.190663] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <6>[ 4.199325] caam 30900000.caam: Entropy delay = 3200 <6>[ 4.204963] caam 30900000.caam: Instantiated RNG4 SH0 <6>[ 4.264374] caam 30900000.caam: Instantiated RNG4 SH1 <6>[ 4.269707] caam 30900000.caam: device ID = 0x0a16030000000000 (Era 8) <6>[ 4.276545] caam 30900000.caam: job rings = 3, qi = 0 <4>[ 4.285953] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <6>[ 4.312161] caam algorithms registered in /proc/crypto <6>[ 4.325299] caam_jr 30901000.jr0: registering rng-caam <6>[ 4.332448] caam 30900000.caam: caam pkc algorithms registered in /proc/crypto <6>[ 4.342974] usbcore: registered new interface driver usbhid <6>[ 4.348824] usbhid: USB HID core driver <6>[ 4.356656] imx7d_adc 30610000.adc: Linked as a consumer to regulator.5 <6>[ 4.367980] imx7d_adc 30620000.adc: Linked as a consumer to regulator.5 <6>[ 4.491857] NET: Registered protocol family 10 <6>[ 4.497971] mmc1: new ultra high speed SDR104 SDIO card at address 0001 <6>[ 4.513765] Segment Routing with IPv6 <6>[ 4.517911] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.526134] NET: Registered protocol family 17 <6>[ 4.530884] can: controller area network core (rev 20170425 abi 9) <6>[ 4.537741] NET: Registered protocol family 29 <6>[ 4.542550] can: raw protocol (rev 20170425) <6>[ 4.547201] can: broadcast manager protocol (rev 20170425 t) <6>[ 4.553328] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 4.559686] Key type dns_resolver registered <5>[ 4.564570] Registering SWP/SWPB emulation handler <5>[ 4.571099] Loading compiled-in X.509 certificates <6>[ 4.714372] imx6q-pcie 33800000.pcie: host bridge /soc/aips-bus@30800000/pcie@33800000 ranges: <6>[ 4.723521] imx6q-pcie 33800000.pcie: IO 0x4ff80000..0x4ff8ffff -> 0x00000000 <6>[ 4.731439] imx6q-pcie 33800000.pcie: MEM 0x40000000..0x4fefffff -> 0x40000000 <3>[ 5.852291] imx6q-pcie 33800000.pcie: Phy link never came up <6>[ 5.862395] imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00 <6>[ 5.869050] pci_bus 0000:00: root bus resource [bus 00-ff] <6>[ 5.874904] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 5.881372] pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fefffff] <6>[ 5.893318] PCI: bus0: Fast back to back transfers disabled <6>[ 5.902078] PCI: bus1: Fast back to back transfers enabled <6>[ 5.907905] pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x400fffff 64bit] <6>[ 5.915582] pci 0000:00:00.0: BAR 6: assigned [mem 0x40100000-0x4010ffff pref] <6>[ 5.923149] pci 0000:00:00.0: PCI bridge to [bus 01-ff] <6>[ 5.930726] panel-simple panel: Linked as a consumer to regulator.21 <6>[ 5.940163] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 5.947145] [drm] No driver support for vblank timestamp query. <6>[ 5.969142] Console: switching to colour frame buffer device 60x34 <6>[ 5.977290] mxsfb 30730000.lcdif: fb0: DRM emulated frame buffer device <6>[ 5.987953] [drm] Initialized mxsfb-drm 1.0.0 20160824 for 30730000.lcdif on minor 0 <6>[ 5.999697] imx_thermal tempmon: Commercial CPU temperature grade - max:95C critical:90C passive:85C <6>[ 6.013984] input: gpio-keys as /devices/platform/gpio-keys/input/input2 <6>[ 6.021948] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:02 UTC (2) <6>[ 6.042932] Generic PHY 30be0000.ethernet-1:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL) <6>[ 6.057753] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.072422] Generic PHY 30be0000.ethernet-1:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=30be0000.ethernet-1:01, irq=POLL) <6>[ 6.085780] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready <6>[ 10.193435] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 10.202107] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 10.233559] Sending DHCP requests .., OK <6>[ 12.936112] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.166 <6>[ 12.944057] IP-Config: Complete: <6>[ 12.947570] device=eth0, hwaddr=00:04:9f:05:b3:72, ipaddr=172.16.1.166, mask=255.255.255.0, gw=172.16.1.4 <6>[ 12.957925] host=172.16.1.166, domain=example.org, nis-domain=(none) <6>[ 12.965045] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 12.965052] nameserver0=172.16.1.4 <5>[ 12.989607] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 13.047158] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <6>[ 13.058197] ALSA device list: <6>[ 13.061447] No soundcards found. <4>[ 13.066046] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 13.075240] cfg80211: failed to load regulatory.db <6>[ 13.084390] Freeing unused kernel memory: 1024K <6>[ 13.102317] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 13.439589] udevd[197]: starting version 3.2.9 <5>[ 13.446772] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.454840] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.461806] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 13.480088] udevd[197]: specified user 'tss' unknown <27>[ 13.486239] udevd[197]: specified group 'tss' unknown <30>[ 13.499457] udevd[198]: starting eudev-3.2.9 <6>[ 14.870353] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 14.934922] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 done Saving random seed: <5>[ 15.407764] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 15.583714] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh exp<3>[ 16.022294] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 ort SHELL=/bin/sh / # . /lava-1140208/environment . /lava-1140208/environment / # /lava-1140208/bin/lava-test-runner /lava-1140208/0 /lava-1140208/bin/lava-test-runner /lava-1140208/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1140208/0/tests/0_dmesg + cat uuid + UUID=1140208_1.5.2.4.1<8>[ 21.506469] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 21.590655] <8>[ 21.666415] <8>[ 21.741638] + set +x <8>[ 21.753312] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1140208/environment / # . /lava-1140208/environment/lava-1140208/bin/lava-test-runner /lava-1140208/1 / # /lava-1140208/bin/lava-test-runner /lava-1140208/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1140208/1/tests/1_bootrr + cat uuid + UUID=1140208_1.5.2.4.5<8>[ 27.554082] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1140208/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-1140208/1/../bin/lava-test-case <8>[ 27.654297] /lava-1140208/1/../bin/lava-test-case <8>[ 28.740545] /lava-1140208/1/../bin/lava-test-case <8>[ 28.782867] + set +x <8>[ 28.813016] / #