connecting to NetworkSerialPort(target=Target(name='tegra124-jetson-tk1', env=None), name='USBSerialPort', state=, avail=True, host='nuc-1', port=42709, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:42709 connected to 192.168.0.1 (port 42709) Escape character: Ctrl-\ Type the escape character to get to the prompt. U-Boot SPL 2015.10 (Dec 03 2015 - 13:25:02) U-Boot 2015.10 (Dec 03 2015 - 13:25:02 -0800) TEGRA124 Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MC: Tegra SD/MMC: 0, Tegra SD/MMC: 1 tegra-pcie: PCI regions: tegra-pcie: I/O: 0x12000000-0x12010000 tegra-pcie: non-prefetchable memory: 0x13000000-0x20000000 tegra-pcie: prefetchable memory: 0x20000000-0x40000000 tegra-pcie: 2x1, 1x1 configuration tegra-pcie: probing port 0, using 2 lanes tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, retrying tegra-pcie: link 0 down, ignoring tegra-pcie: probing port 1, using 1 lanes In: serial Out: serial Err: serial Net: RTL8169#0 Hit any key to stop autoboot: 2  0 Tegra124 (Jetson TK1) # setenv autoload no setenv autoload no Tegra124 (Jetson TK1) # setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff Tegra124 (Jetson TK1) # setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff Tegra124 (Jetson TK1) # dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.0.213 (7 ms) Tegra124 (Jetson TK1) # setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 Tegra124 (Jetson TK1) # tftp 0x81000000 3163203/tftp-deploy-cvb9pry0/kernel/zImage tftp 0x81000000 3163203/tftp-deploy-cvb9pry0/kernel/zImage Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '3163203/tftp-deploy-cvb9pry0/kernel/zImage'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 2.9 MiB/s done Bytes transferred = 8729088 (853200 hex) Tegra124 (Jetson TK1) # tftp 0x82800000 3163203/tftp-deploy-cvb9pry0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x82800000 3163203/tftp-deploy-cvb9pry0/ramdisk/ramdisk.cpio.gz.uboot Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '3163203/tftp-deploy-cvb9pry0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x82800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 3 MiB/s done Bytes transferred = 13339845 (cb8cc5 hex) Tegra124 (Jetson TK1) # setenv initrd_size ${filesize} setenv initrd_size ${filesize} Tegra124 (Jetson TK1) # tftp 0x83f80000 3163203/tftp-deploy-cvb9pry0/dtb/tegra124-jetson-tk1.dtb tftp 0x83f80000 3163203/tftp-deploy-cvb9pry0/dtb/tegra124-jetson-tk1.dtb Using RTL8169#0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.213 Filename '3163203/tftp-deploy-cvb9pry0/dtb/tegra124-jetson-tk1.dtb'. Load address: 0x83f80000 Loading: *##### 2.9 MiB/s done Bytes transferred = 66552 (103f8 hex) Tegra124 (Jetson TK1) # setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp' Tegra124 (Jetson TK1) #bootz 0x81000000 0x82800000 0x83f80000 bootz 0x81000000 0x82800000 0x83f80000 Kernel image @ 0x81000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 82800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13339781 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83f80000 Booting using the fdt blob at 0x83f80000 Using Device Tree in place at 83f80000, end 83f933f7 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.269-cip88-rt28 (KernelCI@build-j877169-arm-gcc-10-multi-v7-defconfig-rcrmc) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Jan 18 20:44:00 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc0f3] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: NVIDIA Tegra124 Jetson TK1 [ 0.000000] earlycon: uart0 at MMIO 0x70006300 (options '115200n8') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xfb800000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522496 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 1978396K/2096128K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 52196K reserved, 65536K cma-reserved, 1244160K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] /interrupt-controller@60004000: 160 interrupts forwarded to /interrupt-controller@50041000 <6>[ 0.000010] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns <6>[ 0.008947] clocksource: timer_us: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns <6>[ 0.019139] Switching to timer-based delay loop, resolution 1000ns <6>[ 0.031319] arch_timer: cp15 timer(s) running at 12.00MHz (virt). <6>[ 0.037914] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2c47f4ee7, max_idle_ns: 440795202497 ns <6>[ 0.049371] sched_clock: 56 bits at 12MHz, resolution 83ns, wraps every 4398046511096ns <6>[ 0.057942] Switching to timer-based delay loop, resolution 83ns <6>[ 0.064941] Console: colour dummy device 80x30 <6>[ 0.069845] Calibrating delay loop (skipped), value calculated using timer frequency.. 24.00 BogoMIPS (lpj=120000) <6>[ 0.080862] pid_max: default: 32768 minimum: 301 <6>[ 0.086027] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.093171] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.101247] CPU: Testing write buffer coherency: ok <6>[ 0.106612] CPU0: Spectre v2: using ICIALLU workaround <6>[ 0.112209] CPU0: Spectre BHB: enabling loop workaround for all CPUs <3>[ 0.119342] /cpus/cpu@0 missing clock-frequency property <3>[ 0.125149] /cpus/cpu@1 missing clock-frequency property <3>[ 0.130974] /cpus/cpu@2 missing clock-frequency property <3>[ 0.136783] /cpus/cpu@3 missing clock-frequency property <6>[ 0.142574] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.149216] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.158261] rcu: Hierarchical SRCU implementation. <6>[ 0.166825] Tegra Revision: A01 SKU: 129 CPU Process: 1 SoC Process: 1 <6>[ 0.174588] EFI services will not be available. <6>[ 0.179782] smp: Bringing up secondary CPUs ... <6>[ 0.185442] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.185448] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.202498] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <3>[ 0.202504] CPU2: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.219537] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <3>[ 0.219543] CPU3: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.235897] smp: Brought up 1 node, 4 CPUs <6>[ 0.240435] SMP: Total of 4 processors activated (96.00 BogoMIPS). <6>[ 0.247111] CPU: All CPU(s) started in SVC mode. <6>[ 0.253790] devtmpfs: initialized <6>[ 0.270557] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.279135] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.289622] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.297662] pinctrl core: initialized pinctrl subsystem <6>[ 0.305005] DMI not present or invalid. <6>[ 0.309889] NET: Registered protocol family 16 <6>[ 0.316952] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.327022] cpuidle: using governor menu <6>[ 0.350351] No ATAGs? <6>[ 0.350481] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.361686] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.383084] Serial: AMBA PL011 UART driver <6>[ 0.389095] iommu: Adding device 50000000.host1x to group 0 <6>[ 0.395224] iommu: Adding device 54200000.dc to group 1 <6>[ 0.400950] iommu: Adding device 54240000.dc to group 1 <6>[ 0.406717] iommu: Adding device 57000000.gpu to group 2 <6>[ 0.436524] +5V_SYS: supplied by +VDD_MUX <6>[ 0.441262] +3.3V_SYS: supplied by +VDD_MUX <6>[ 0.446603] +USB0_VBUS_SW: supplied by +5V_SYS <6>[ 0.451802] +5V_USB_HS: supplied by +5V_SYS <6>[ 0.457062] +5V_HDMI_CON: supplied by +5V_SYS <6>[ 0.462189] +5V_SATA: supplied by +5V_SYS <6>[ 0.466910] +12V_SATA: supplied by +VDD_MUX <6>[ 0.474558] vgaarb: loaded <5>[ 0.478374] SCSI subsystem initialized <6>[ 0.482940] usbcore: registered new interface driver usbfs <6>[ 0.488941] usbcore: registered new interface driver hub <6>[ 0.494780] usbcore: registered new device driver usb <6>[ 0.504041] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.509479] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.519234] PTP clock support registered <6>[ 0.523774] EDAC MC: Ver: 3.0.0 <6>[ 0.530373] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.600902] NET: Registered protocol family 2 <6>[ 0.605874] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.614095] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.622364] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.630017] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.637149] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.644098] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.650566] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.657564] NET: Registered protocol family 1 <6>[ 0.662843] RPC: Registered named UNIX socket transport module. <6>[ 0.669254] RPC: Registered udp transport module. <6>[ 0.674429] RPC: Registered tcp transport module. <6>[ 0.679579] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.686937] Trying to unpack rootfs image as initramfs... <6>[ 1.656722] Freeing initrd memory: 13028K <6>[ 1.662037] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <5>[ 1.672189] Initialise system trusted keyrings <6>[ 1.677267] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 1.690883] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.697871] NFS: Registering the id_resolver key type <5>[ 1.703436] Key type id_resolver registered <5>[ 1.708044] Key type id_legacy registered <6>[ 1.712521] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.719156] Key type asymmetric registered <5>[ 1.723698] Asymmetric key parser 'x509' registered <6>[ 1.729072] bounce: pool size: 64 pages <6>[ 1.733368] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.741325] io scheduler noop registered <6>[ 1.745661] io scheduler deadline registered <6>[ 1.750582] io scheduler cfq registered (default) <6>[ 1.755729] io scheduler mq-deadline registered <6>[ 1.760710] io scheduler kyber registered <4>[ 1.769564] usb2-0: usb2-0 supply vbus not found, using dummy regulator <6>[ 1.776877] usb2-0: Linked as a consumer to regulator.0 <4>[ 1.782744] usb2-1: usb2-1 supply vbus not found, using dummy regulator <6>[ 1.790008] usb2-1: Linked as a consumer to regulator.0 <6>[ 1.795907] usb2-2: Linked as a consumer to regulator.6 <4>[ 1.801783] usb3-0: usb3-0 supply vbus not found, using dummy regulator <6>[ 1.809052] usb3-0: Linked as a consumer to regulator.0 <6>[ 1.828274] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <3>[ 1.834378] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 <3>[ 1.850024] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator <6>[ 1.864684] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels <6>[ 1.876510] tegra-pmc 7000e400.pmc: emergency thermal reset enabled <6>[ 1.934430] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.944443] console [ttyS0] disabled <6>[ 1.948450] 70006300.serial: ttyS0 at MMIO 0x70006300 (irq = 79, base_baud = 25500000) is a Tegra <6>[ 1.957965] console [ttyS0] enabled <6>[ 1.957965] console [ttyS0] enabled <6>[ 1.965596] bootconsole [uart0] disabled <6>[ 1.965596] bootconsole [uart0] disabled <6>[ 1.975108] SuperH (H)SCI(F) driver initialized <6>[ 1.981068] msm_serial: driver initialized <6>[ 1.985623] STMicroelectronics ASC driver initialized <6>[ 1.991664] 70006000.serial: ttyTHS1 at MMIO 0x70006000 (irq = 77, base_baud = 0) is a TEGRA_UART <6>[ 2.001237] 70006040.serial: ttyTHS2 at MMIO 0x70006040 (irq = 78, base_baud = 0) is a TEGRA_UART <6>[ 2.011176] STM32 USART driver initialized <4>[ 2.021502] Failed to attached device 54200000.dc to IOMMU_mapping <4>[ 2.036154] Failed to attached device 54240000.dc to IOMMU_mapping <6>[ 2.051360] tegra-hdmi 54280000.hdmi: Linked as a consumer to regulator.8 <3>[ 2.058428] tegra-hdmi 54280000.hdmi: failed to get PLL regulator <6>[ 2.064856] tegra-hdmi 54280000.hdmi: Dropping the link to regulator.8 <6>[ 2.082547] brd: module loaded <6>[ 2.092932] loop: module loaded <6>[ 2.097605] at24 0-0056: 256 byte 24c02 EEPROM, writable, 8 bytes/write <6>[ 2.106314] as3722 4-0040: AS3722 with revision 0x1 found <6>[ 2.118876] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 2.124182] +1.35V_LP0(sd3): Bringing 0uV into 1350000-1350000uV <6>[ 2.130610] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 2.136056] +1.05V_RUN: supplied by +5V_SYS <6>[ 2.140774] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 2.147085] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 2.153539] +1.8V_RUN_CAM: Bringing 0uV into 1800000-1800000uV <6>[ 2.160146] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 2.166362] +1.05V_LP0_VDD_RTC: Bringing 1100000uV into 1000000-1000000uV <6>[ 2.173551] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 2.179901] +2.8V_RUN_CAM: Bringing 0uV into 2800000-2800000uV <6>[ 2.186336] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 2.191459] +1.2V_RUN_CAM_FRONT: Bringing 0uV into 1200000-1200000uV <6>[ 2.198406] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 2.204235] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 2.210148] +VDDIO_SDMMC3: failed to get the current voltage(-517) <3>[ 2.216625] as3722-regulator as3722-regulator: regulator 13 register failed -517 <3>[ 2.229857] tegra-ahci 70027000.sata: Failed to get supply 'avdd': -517 <3>[ 2.236757] tegra-ahci 70027000.sata: Failed to get regulators <6>[ 2.259679] m25p80 spi1.0: w25q32dw (4096 Kbytes) <6>[ 2.268519] CAN device driver interface <6>[ 2.273652] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 2.280893] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.286978] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.293216] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.300442] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.311070] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.318755] usbcore: registered new interface driver pegasus <6>[ 2.324732] usbcore: registered new interface driver asix <6>[ 2.330435] usbcore: registered new interface driver ax88179_178a <6>[ 2.336807] usbcore: registered new interface driver cdc_ether <6>[ 2.342950] usbcore: registered new interface driver smsc75xx <6>[ 2.348989] usbcore: registered new interface driver smsc95xx <6>[ 2.355042] usbcore: registered new interface driver net1080 <6>[ 2.361005] usbcore: registered new interface driver cdc_subset <6>[ 2.367204] usbcore: registered new interface driver zaurus <6>[ 2.373106] usbcore: registered new interface driver cdc_ncm <5>[ 2.379251] tegra-phy 7d000000.usb-phy: no vbus regulator <5>[ 2.385143] tegra-phy 7d004000.usb-phy: no vbus regulator <6>[ 2.391014] tegra-phy 7d008000.usb-phy: Linked as a consumer to regulator.6 <6>[ 2.400563] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.407342] ehci-pci: EHCI PCI platform driver <6>[ 2.412096] ehci-platform: EHCI generic platform driver <6>[ 2.417795] ehci-orion: EHCI orion driver <6>[ 2.422252] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.426672] ehci-st: EHCI STMicroelectronics driver <6>[ 2.431979] ehci-exynos: EHCI EXYNOS driver <6>[ 2.436570] ehci-atmel: EHCI Atmel driver <6>[ 2.440999] tegra-ehci: Tegra EHCI driver <6>[ 2.449583] tegra-ehci 7d004000.usb: EHCI Host Controller <6>[ 2.455279] tegra-ehci 7d004000.usb: new USB bus registered, assigned bus number 1 <6>[ 2.463282] tegra-ehci 7d004000.usb: irq 100, io mem 0x7d004000 <6>[ 2.490401] tegra-ehci 7d004000.usb: USB 2.0 started, EHCI 1.10 <6>[ 2.497234] hub 1-0:1.0: USB hub found <6>[ 2.501307] hub 1-0:1.0: 1 port detected <6>[ 2.508032] tegra-ehci 7d008000.usb: EHCI Host Controller <6>[ 2.513726] tegra-ehci 7d008000.usb: new USB bus registered, assigned bus number 2 <6>[ 2.521726] tegra-ehci 7d008000.usb: irq 101, io mem 0x7d008000 <6>[ 2.550401] tegra-ehci 7d008000.usb: USB 2.0 started, EHCI 1.10 <6>[ 2.557192] hub 2-0:1.0: USB hub found <6>[ 2.561262] hub 2-0:1.0: 1 port detected <6>[ 2.565863] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.572329] ohci-pci: OHCI PCI platform driver <6>[ 2.577066] ohci-platform: OHCI generic platform driver <6>[ 2.582788] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.587212] ohci-st: OHCI STMicroelectronics driver <6>[ 2.592522] ohci-atmel: OHCI Atmel driver <6>[ 2.597593] usbcore: registered new interface driver usb-storage <6>[ 2.615144] as3722-rtc as3722-rtc: rtc core: registered as3722-rtc as rtc0 <6>[ 2.622302] as3722-rtc as3722-rtc: RTC interrupt 379 <6>[ 2.631293] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1 <5>[ 2.638720] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock <6>[ 2.645794] i2c /dev entries driver <4>[ 2.657619] lm90 0-004c: 0-004c supply vcc not found, using dummy regulator <6>[ 2.664912] lm90 0-004c: Linked as a consumer to regulator.0 <6>[ 2.682827] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.689260] sdhci: Copyright(c) Pierre Ossman <6>[ 2.695731] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.703620] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.710407] sdhci-tegra 700b0400.sdhci: Got CD GPIO <6>[ 2.715566] sdhci-tegra 700b0400.sdhci: Got WP GPIO <3>[ 2.737120] mmc0: Unknown controller version (3). You may experience problems. <4>[ 2.744653] mmc0: Invalid maximum block size, assuming 512 bytes <6>[ 2.781916] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA <6>[ 2.792254] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.799200] usbcore: registered new interface driver usbhid <6>[ 2.805050] usbhid: USB HID core driver <6>[ 2.813911] NET: Registered protocol family 10 <6>[ 2.819572] Segment Routing with IPv6 <6>[ 2.823592] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.830297] NET: Registered protocol family 17 <6>[ 2.835028] can: controller area network core (rev 20170425 abi 9) <6>[ 2.841543] NET: Registered protocol family 29 <6>[ 2.846245] can: raw protocol (rev 20170425) <6>[ 2.850791] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.856715] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.862800] Key type dns_resolver registered <6>[ 2.867664] ThumbEE CPU extension supported. <5>[ 2.872219] Registering SWP/SWPB emulation handler <5>[ 2.878007] Loading compiled-in X.509 certificates <6>[ 2.900596] +3.3V_RUN: supplied by +3.3V_SYS <6>[ 2.906464] +3.3V_LP0: supplied by +3.3V_SYS <6>[ 2.911654] +3.3V_AVDD_HDMI_AP_GATED: supplied by +3.3V_RUN <6>[ 2.918335] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <3>[ 2.924281] tegra-pcie 1003000.pcie: Failed to get supply 'avddio-pex': -517 <3>[ 2.935514] tegra124-dfll 70110000.clock: couldn't get vdd_cpu regulator <6>[ 2.947797] tegra-hdmi 54280000.hdmi: Linked as a consumer to regulator.8 <3>[ 2.954952] tegra-hdmi 54280000.hdmi: failed to get PLL regulator <6>[ 2.961505] tegra-hdmi 54280000.hdmi: Dropping the link to regulator.8 <4>[ 2.969761] as3722-regulator as3722-regulator: DMA mask not set <6>[ 2.977830] +1.35V_LP0(sd2): supplied by +5V_SYS <6>[ 2.983117] +1.35V_LP0(sd3): supplied by +5V_SYS <6>[ 2.988404] +1.05V_RUN: supplied by +5V_SYS <6>[ 2.992987] +1.8V_VDDIO: supplied by +5V_SYS <6>[ 2.999068] +1.05V_RUN_AVDD: supplied by +1.35V_LP0(sd2) <6>[ 3.005467] +1.8V_RUN_CAM: supplied by +3.3V_RUN <6>[ 3.010486] +1.2V_GEN_AVDD: supplied by +1.8V_VDDIO <6>[ 3.016558] +1.05V_LP0_VDD_RTC: supplied by +3.3V_SYS <6>[ 3.022901] +2.8V_RUN_CAM: supplied by +3.3V_SYS <6>[ 3.028015] +1.2V_RUN_CAM_FRONT: supplied by +1.8V_VDDIO <3>[ 3.033730] +VDDIO_SDMMC3: bypassed regulator has no supply! <3>[ 3.039645] +VDDIO_SDMMC3: failed to get the current voltage(-517) <6>[ 3.046117] +VDDIO_SDMMC3: supplied by +3.3V_RUN <6>[ 3.051966] +1.05V_RUN_CAM_REAR: Bringing 0uV into 1050000-1050000uV <6>[ 3.059018] +1.05V_RUN_CAM_REAR: supplied by +1.8V_VDDIO <6>[ 3.065158] +3.3V_RUN_TOUCH: Bringing 0uV into 2800000-2800000uV <6>[ 3.072591] +3.3V_RUN_TOUCH: supplied by +5V_SYS <6>[ 3.077707] +2.8V_RUN_CAM_AF: Bringing 0uV into 2800000-2800000uV <6>[ 3.084504] +2.8V_RUN_CAM_AF: supplied by +5V_SYS <6>[ 3.089722] +1.8V_RUN_VPP_FUSE: Bringing 0uV into 1800000-1800000uV <6>[ 3.096597] +1.8V_RUN_VPP_FUSE: supplied by +3.3V_RUN <6>[ 3.103287] tegra-ahci 70027000.sata: Linked as a consumer to regulator.31 <6>[ 3.110528] tegra-ahci 70027000.sata: Linked as a consumer to regulator.26 <6>[ 3.117826] tegra-ahci 70027000.sata: Linked as a consumer to regulator.9 <6>[ 3.124971] tegra-ahci 70027000.sata: Linked as a consumer to regulator.10 <6>[ 3.133592] tegra-ahci 70027000.sata: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl platform mode <6>[ 3.142928] tegra-ahci 70027000.sata: flags: 64bit ncq sntf pm led pmp pio slum part sadm sds apst <6>[ 3.153851] mmc0: new high speed MMC card at address 0001 <6>[ 3.159808] scsi host0: tegra-ahci <6>[ 3.164453] mmcblk0: mmc0:0001 SEM16G 14.7 GiB <6>[ 3.169707] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB <6>[ 3.176333] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB <6>[ 3.182841] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB, chardev (235:0) <6>[ 3.190736] scsi host1: tegra-ahci <6>[ 3.194719] ata1: SATA max UDMA/133 mmio [mem 0x70027000-0x70028fff] port 0x100 irq 89 <6>[ 3.202924] ata2: DUMMY <6>[ 3.206591] cpu cpu0: Linked as a consumer to regulator.27 <6>[ 3.212911] cpu cpu0: Dropping the link to regulator.27 <6>[ 3.220171] sdhci-tegra 700b0400.sdhci: Got CD GPIO <6>[ 3.225381] sdhci-tegra 700b0400.sdhci: Got WP GPIO <6>[ 3.232892] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 <6>[ 3.241945] sdhci-tegra 700b0400.sdhci: Linked as a consumer to regulator.40 <3>[ 3.249270] mmc1: Unknown controller version (3). You may experience problems. <4>[ 3.257755] mmc1: Invalid maximum block size, assuming 512 bytes <6>[ 3.296444] mmc1: SDHCI controller on 700b0400.sdhci [700b0400.sdhci] using ADMA <6>[ 3.304989] tegra-pcie 1003000.pcie: 2x1, 1x1 configuration <6>[ 3.311004] tegra-pcie 1003000.pcie: Linked as a consumer to regulator.31 <6>[ 3.318261] tegra-pcie 1003000.pcie: Linked as a consumer to regulator.26 <6>[ 3.325606] tegra-pcie 1003000.pcie: Linked as a consumer to regulator.34 <6>[ 3.334498] tegra-pcie 1003000.pcie: probing port 0, using 2 lanes <3>[ 3.342559] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000008 <6>[ 3.533379] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.682423] mmc1: new high speed SD card at address 0260 <6>[ 3.688919] mmcblk1: mmc1:0260 1232 961 MiB <6>[ 3.695588] mmcblk1: p1 p2 <3>[ 3.760487] tegra-pcie 1003000.pcie: link 0 down, retrying <3>[ 4.168875] tegra-pcie 1003000.pcie: link 0 down, retrying <3>[ 4.576780] tegra-pcie 1003000.pcie: link 0 down, retrying <6>[ 4.584667] tegra-pcie 1003000.pcie: link 0 down, ignoring <6>[ 4.590469] tegra-pcie 1003000.pcie: probing port 1, using 1 lanes <3>[ 4.599019] tegra-pcie 1003000.pcie: Slot present pin change, signature: 00000000 <6>[ 4.612758] tegra-pcie 1003000.pcie: PCI host bridge to bus 0000:00 <6>[ 4.619287] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] <6>[ 4.625756] pci_bus 0000:00: root bus resource [mem 0x13000000-0x1fffffff] <6>[ 4.632899] pci_bus 0000:00: root bus resource [mem 0x20000000-0x3fffffff pref] <6>[ 4.640474] pci_bus 0000:00: root bus resource [bus 00-ff] <4>[ 4.646643] pci_bus 0000:00: 2-byte config write to 0000:00:02.0 offset 0x4 may corrupt adjacent RW1C bits <6>[ 4.656599] pci 0000:00:02.0: enabling Extended Tags <6>[ 4.666194] PCI: bus0: Fast back to back transfers disabled <6>[ 4.672045] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring <6>[ 4.714893] PCI: bus1: Fast back to back transfers disabled <6>[ 4.720790] pci 0000:00:02.0: BAR 8: assigned [mem 0x13000000-0x130fffff] <6>[ 4.727835] pci 0000:00:02.0: BAR 9: assigned [mem 0x20000000-0x200fffff 64bit pref] <6>[ 4.735849] pci 0000:00:02.0: BAR 7: assigned [io 0x1000-0x1fff] <6>[ 4.742217] pci 0000:01:00.0: BAR 4: assigned [mem 0x20000000-0x20003fff 64bit pref] <6>[ 4.750233] pci 0000:01:00.0: BAR 2: assigned [mem 0x13000000-0x13000fff 64bit] <6>[ 4.757828] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] <6>[ 4.764197] pci 0000:00:02.0: PCI bridge to [bus 01] <6>[ 4.769419] pci 0000:00:02.0: bridge window [io 0x1000-0x1fff] <6>[ 4.775784] pci 0000:00:02.0: bridge window [mem 0x13000000-0x130fffff] <6>[ 4.782840] pci 0000:00:02.0: bridge window [mem 0x20000000-0x200fffff 64bit pref] <4>[ 4.790879] pci 0000:00:02.0: nv_msi_ht_cap_quirk didn't locate host bridge <6>[ 4.798227] pcieport 0000:00:02.0: enabling device (0140 -> 0143) <6>[ 4.804840] pcieport 0000:00:02.0: Signaling PME with IRQ 395 <6>[ 4.811172] r8169 0000:01:00.0: enabling device (0140 -> 0143) <6>[ 4.862401] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 00:04:4b:21:2a:66, XID 4c000800, IRQ 396 <6>[ 4.871247] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko] <6>[ 4.883138] tegra124-dfll 70110000.clock: Linked as a consumer to regulator.27 <6>[ 4.893323] tegra-hdmi 54280000.hdmi: Linked as a consumer to regulator.8 <6>[ 4.900450] +1.05V_RUN_AVDD_HDMI_PLL: supplied by +1.05V_RUN <6>[ 4.906500] tegra-hdmi 54280000.hdmi: Linked as a consumer to regulator.7 <6>[ 4.913710] tegra-hdmi 54280000.hdmi: Linked as a consumer to regulator.4 <6>[ 4.923776] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 4.930685] [drm] No driver support for vblank timestamp query. <6>[ 4.936917] [drm] Cannot find any crtc or sizes <6>[ 4.941937] [drm] Initialized tegra 0.0.0 20120330 for drm on minor 0 <6>[ 4.949434] cpu cpu0: Linked as a consumer to regulator.27 <4>[ 4.956296] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 696000 KHz <4>[ 4.963954] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 714000 KHz <6>[ 4.973169] [drm] Cannot find any crtc or sizes <6>[ 4.978249] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 4.985806] as3722-rtc as3722-rtc: setting system clock to 2000-01-01 00:00:17 UTC (946684817) <4>[ 4.995476] r8169 0000:01:00.0: Direct firmware load for rtl_nic/rtl8168g-2.fw failed with error -2 <4>[ 5.004807] r8169 0000:01:00.0 eth0: unable to load firmware patch rtl_nic/rtl8168g-2.fw (-2) <6>[ 5.013803] Generic PHY r8169-100:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=r8169-100:00, irq=IGNORE) <6>[ 5.163374] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.170097] r8169 0000:01:00.0 eth0: Link is Down <6>[ 6.835645] r8169 0000:01:00.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 6.843882] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.870722] Sending DHCP requests ., OK <6>[ 6.914989] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.213 <6>[ 6.923041] IP-Config: Complete: <6>[ 6.926534] device=eth0, hwaddr=00:04:4b:21:2a:66, ipaddr=192.168.0.213, mask=255.255.255.0, gw=192.168.0.254 <6>[ 6.937158] host=192.168.0.213, domain=lan, nis-domain=(none) <6>[ 6.943634] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 6.943637] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 6.958920] Freeing unused kernel memory: 2048K <6>[ 6.980700] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.074406] udevd[119]: starting version 3.2.9 <5>[ 7.079655] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.086710] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.093583] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.103046] udevd[119]: specified user 'tss' unknown <27>[ 7.108387] udevd[119]: specified group 'tss' unknown <30>[ 7.115363] udevd[120]: starting eudev-3.2.9 <6>[ 7.219432] tegra-wdt 60005000.timer: initialized (heartbeat = 120 sec, nowayout = 0) <27>[ 7.221360] udevd[129]: Error changing net interface name eth0 to enp1s0: Device or resource busy <28>[ 7.236835] udevd[129]: could not rename interface '3' from 'eth0' to 'enp1s0': Device or resource busy <6>[ 7.251813] nouveau 57000000.gpu: Linked as a consumer to regulator.33 <6>[ 7.258791] nouveau 57000000.gpu: NVIDIA GK20A (0ea000a1) <6>[ 7.261073] tegra-xusb 70090000.usb: Linked as a consumer to regulator.31 <6>[ 7.264530] nouveau 57000000.gpu: imem: using IOMMU <6>[ 7.271646] tegra-xusb 70090000.usb: Linked as a consumer to regulator.26 <4>[ 7.276887] nouveau 57000000.gpu: Direct firmware load for nvidia/gk20a/fecs_inst.bin failed with error -2 <6>[ 7.283905] tegra-snd-rt5640 sound: ASoC: CPU DAI (null) not registered <6>[ 7.292393] tegra-xusb 70090000.usb: Linked as a consumer to regulator.32 <6>[ 7.292454] tegra-xusb 70090000.usb: Linked as a consumer to regulator.34 <4>[ 7.293611] nouveau 57000000.gpu: Direct firmware load for nouveau/nvea_fuc409c failed with error -2 <3>[ 7.300427] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <6>[ 7.302082] tegra-snd-rt5640 sound: ASoC: CPU DAI (null) not registered <4>[ 7.307578] nouveau 57000000.gpu: Direct firmware load for nouveau/fuc409c failed with error -2 <3>[ 7.314504] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <3>[ 7.323878] nouveau 57000000.gpu: gr: failed to load fuc409c <4>[ 7.330629] tegra-xusb 70090000.usb: Direct firmware load for nvidia/tegra124/xusb.bin failed with error -2 <3>[ 7.330635] tegra-xusb 70090000.usb: failed to request firmware: -2 <3>[ 7.330639] tegra-xusb 70090000.usb: failed to load firmware: -2 <6>[ 7.331478] tegra-xusb 70090000.usb: Dropping the link to regulator.32 <6>[ 7.388975] tegra-xusb 70090000.usb: Dropping the link to regulator.34 <4>[ 7.395962] tegra-xusb: probe of 70090000.usb failed with error -2 <6>[ 7.465212] [TTM] Zone kernel: Available graphics memory: 374656 kiB <6>[ 7.471971] [TTM] Zone highmem: Available graphics memory: 1029504 kiB <6>[ 7.478742] [TTM] Initializing pool allocator <6>[ 7.483448] nouveau 57000000.gpu: DRM: VRAM: 0 MiB <6>[ 7.488522] nouveau 57000000.gpu: DRM: GART: 1048576 MiB <3>[ 7.496851] nouveau 57000000.gpu: DRM: failed to create kernel channel, -22 <4>[ 7.515869] tegra30-i2s 70301100.i2s: DMA channels sourced from device 70300000.ahub <3>[ 7.525007] tegra-snd-rt5640 sound: ASoC: CODEC DAI rt5640-aif1 not registered <3>[ 7.532485] tegra-snd-rt5640 sound: snd_soc_register_card failed (-517) <6>[ 7.715285] tegra-snd-rt5640 sound: rt5640-aif1 <-> 70301100.i2s mapping ok <4>[ 7.722621] tegra-snd-rt5640 sound: ASoC: no DMI vendor name! <6>[ 7.731182] input: NVIDIA Tegra Jetson TK1 Headphones as /devices/soc0/sound/sound/card1/input1 <6>[ 7.941108] [drm] Initialized nouveau 1.3.1 20120801 for 57000000.gpu on minor 1 <6>[ 8.201431] input: tegra-hda HDMI/DP,pcm=3 as /devices/soc0/70030000.hda/sound/card0/input2 done Saving random seed: <5>[ 8.223612] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.282824] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-3163203/environment . /lava-3163203/environment / # /lava-3163203/bin/lava-test-runner /lava-3163203/0 /lava-3163203/bin/lava-test-runner /lava-3163203/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3163203/0/tests/0_dmesg + cat uuid + UUID=3163203_1.5.2.4.1 <8>[ 8.909601] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.942554] <8>[ 8.969372] <8>[ 8.996587] + set +x <8>[ 9.006376] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-3163203/environment / # . /lava-3163203/environment/lava-3163203/bin/lava-test-runner /lava-3163203/1 / # /lava-3163203/bin/lava-test-runner /lava-3163203/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-3163203/1/tests/1_bootrr + cat uuid + UUID=3163203_1.5<8>[ 9.516724] .2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-3163203/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-3163203/1/../bin/lava-test-case <8>[ 9.554987] /lava-3163203/1/../bin/lava-test-case <8>[ 9.578192] /lava-3163203/1/../bin/lava-test-case <8>[ 9.594690] + set +x <8>[ 9.608275] / #