connecting to NetworkSerialPort(target=Target(name='imx6dl-riotboard-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4011, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4011 connected to 10.8.254.5 (port 4011) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2017.10.1-00009-gbc5d99d030 #1 Wed Nov 1 16:14:48 CET 2017 Board: RIoTboard i.MX6S detected i.MX6 Solo revision 1.1 mdio_bus: miibus0: probed imx-usb 2184200.usb: USB EHCI 1.00 imx-esdhc 2194000.usdhc: registered as 2194000.usdhc imx-esdhc 2198000.usdhc: registered as 2198000.usdhc imx-esdhc 219c000.usdhc: registered as 219c000.usdhc imx-ipuv3 2400000.ipu: IPUv3H probed imx-hdmi 120000.hdmi: Detected HDMI controller 0x13:0x1a:0xa0:0xc1 netconsole: registered as netconsole-1 malloc space: 0x2fefb4e0 -> 0x4fdf69bf (size 511 MiB) mmc3: detected MMC card version 4.41 mmc3: registered mmc3.boot0 mmc3: registered mmc3.boot1 mmc3: registered mmc3 running /env/bin/init... [?25h Hit m for menu or any other key to stop autoboot: 3 type exit to get to the menu [1;32mbarebox@[1;36mRIoTboard i.MX6S:/[0m bootm -v -r /mnt/tftp/882600/tftp-deploy-nejepw4g/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/882600/tftp-deploy-nejepw4g/dtb/imx6dl-riotboard.dtb /mnt/tftp/882600/tftp-deploy-nejepw4g/kernel/zImage [1;32mbarebox@[1;36mRIoTboard i.MX6S:/[0m bootm -v -r /mnt/tftp/882600/tftp-deploy-nejepw4g/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/882600/tftp-deploy-nejepw4g/dtb/imx6dl-riotboard.dtb /mnt/tftp/882600/tftp-deploy-nejepw4g/kernel/zImage warning: No MAC address set. Using random address 3a:40:7c:51:86:c9 eth0: 1000Mbps full duplex link detected T DHCP client bound to address 10.8.254.253 Loading ARM Linux zImage '/mnt/tftp/882600/tftp-deploy-nejepw4g/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler no OS load address, defaulting to 0x129a0000 no initrd load address, defaulting to 0x18000000 Loaded initrd GZIP compressed '/mnt/tftp/882600/tftp-deploy-nejepw4g/ramdisk/ramdisk.cpio.gz' initrd is at 0x18000000-0x18cb6b27 Loading devicetree from '/mnt/tftp/882600/tftp-deploy-nejepw4g/dtb/imx6dl-riotboard.dtb' mmc3: Cannot find nodepath /soc/aips-bus@02100000/usdhc@0219c000, cannot fixup Failed to fixup node in of_partition_fixup+0x1/0x1f8: Invalid argument commandline: console=ttymxc1,115200n8 Starting kernel at 0x129a0000, initrd at 0x18000000, oftree at 0x18cb7000... Starting kernel in secure mode [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.269-cip88-rt28 (KernelCI@build-j877169-arm-gcc-10-multi-v7-defconfig-rcrmc) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Jan 18 20:44:00 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: RIoTboard i.MX6S [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x4b800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 938428K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 44612K reserved, 65536K cma-reserved, 195688K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 512 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76450001 [ 0.000000] ccm: ldb_di0_sel already changed from reset value: 0 [ 0.000000] ccm: ldb_di1_sel already changed from reset value: 0 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000026] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.002800] Console: colour dummy device 80x30 [ 0.002848] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.002863] pid_max: default: 32768 minimum: 301 [ 0.002996] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003018] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003624] CPU: Testing write buffer coherency: ok [ 0.003660] CPU0: Spectre v2: using BPIALL workaround [ 0.004013] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004694] Setting up static identity map for 0x10300000 - 0x103000a0 [ 0.006164] rcu: Hierarchical SRCU implementation. [ 0.009188] EFI services will not be available. [ 0.009379] smp: Bringing up secondary CPUs ... [ 0.009392] smp: Brought up 1 node, 1 CPU [ 0.009402] SMP: Total of 1 processors activated (6.00 BogoMIPS). [ 0.009411] CPU: All CPU(s) started in SVC mode. [ 0.010257] devtmpfs: initialized [ 0.016545] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.016906] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016928] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.019180] pinctrl core: initialized pinctrl subsystem [ 0.020769] DMI not present or invalid. [ 0.021544] NET: Registered protocol family 16 [ 0.024404] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.026357] cpuidle: using governor menu [ 0.026512] CPU identified as i.MX6DL, silicon rev 1.1 [ 0.035749] vdd1p1: supplied by regulator-dummy [ 0.036284] vdd3p0: supplied by regulator-dummy [ 0.036784] vdd2p5: supplied by regulator-dummy [ 0.037293] vddarm: supplied by regulator-dummy [ 0.037950] vddpu: supplied by regulator-dummy [ 0.038360] vddsoc: supplied by regulator-dummy [ 0.050767] No ATAGs? [ 0.050822] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.050836] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.053713] imx6dl-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory [ 0.053958] imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.058300] Serial: AMBA PL011 UART driver [ 0.082025] mxs-dma 110000.dma-apbh: initialized [ 0.087544] vgaarb: loaded [ 0.088317] SCSI subsystem initialized [ 0.088757] usbcore: registered new interface driver usbfs [ 0.088806] usbcore: registered new interface driver hub [ 0.088849] usbcore: registered new device driver usb [ 0.090322] i2c i2c-0: IMX I2C adapter registered [ 0.090341] i2c i2c-0: can't use DMA, using PIO instead. [ 0.090845] i2c i2c-1: IMX I2C adapter registered [ 0.090862] i2c i2c-1: can't use DMA, using PIO instead. [ 0.091327] i2c i2c-3: IMX I2C adapter registered [ 0.091345] i2c i2c-3: can't use DMA, using PIO instead. [ 0.092709] pps_core: LinuxPPS API ver. 1 registered [ 0.092719] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.092742] PTP clock support registered [ 0.092949] EDAC MC: Ver: 3.0.0 [ 0.095756] clocksource: Switched to clocksource mxc_timer1 [ 0.152780] NET: Registered protocol family 2 [ 0.153133] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.154058] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.154096] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.154174] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.154309] TCP: Hash tables configured (established 8192 bind 8192) [ 0.154488] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.154528] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.154687] NET: Registered protocol family 1 [ 0.155262] RPC: Registered named UNIX socket transport module. [ 0.155275] RPC: Registered udp transport module. [ 0.155283] RPC: Registered tcp transport module. [ 0.155291] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.155804] Trying to unpack rootfs image as initramfs... [ 1.272039] Freeing initrd memory: 13020K [ 1.272774] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.274474] Initialise system trusted keyrings [ 1.274711] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.280874] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.281713] NFS: Registering the id_resolver key type [ 1.281781] Key type id_resolver registered [ 1.281790] Key type id_legacy registered [ 1.281829] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.283901] Key type asymmetric registered [ 1.283915] Asymmetric key parser 'x509' registered [ 1.283977] bounce: pool size: 64 pages [ 1.284027] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.284038] io scheduler noop registered [ 1.284046] io scheduler deadline registered [ 1.284282] io scheduler cfq registered (default) [ 1.284292] io scheduler mq-deadline registered [ 1.284301] io scheduler kyber registered [ 1.315364] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 1.315437] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 1.315496] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 1.315591] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 [ 1.315761] PU : no governor for states [ 1.315786] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 1.322826] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 1.322847] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 1.371479] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.374953] SuperH (H)SCI(F) driver initialized [ 1.375723] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX [ 1.376647] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 68, base_baud = 5000000) is a IMX [ 2.198802] console [ttymxc1] enabled [ 2.203116] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 69, base_baud = 5000000) is a IMX [ 2.212381] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 70, base_baud = 5000000) is a IMX [ 2.221642] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 71, base_baud = 5000000) is a IMX [ 2.231456] msm_serial: driver initialized [ 2.235834] STMicroelectronics ASC driver initialized [ 2.242094] STM32 USART driver initialized [ 2.263673] brd: module loaded [ 2.275055] loop: module loaded [ 2.290625] CAN device driver interface [ 2.295628] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.302878] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 2.311598] fec 2188000.ethernet: Linked as a consumer to regulator.0 [ 2.320483] pps pps0: new PPS source ptp0 [ 2.350977] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.358076] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.363913] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.369940] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.376925] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.387779] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.395225] usbcore: registered new interface driver pegasus [ 2.400961] usbcore: registered new interface driver asix [ 2.406415] usbcore: registered new interface driver ax88179_178a [ 2.412552] usbcore: registered new interface driver cdc_ether [ 2.418454] usbcore: registered new interface driver smsc75xx [ 2.424247] usbcore: registered new interface driver smsc95xx [ 2.430054] usbcore: registered new interface driver net1080 [ 2.435766] usbcore: registered new interface driver cdc_subset [ 2.441716] usbcore: registered new interface driver zaurus [ 2.447386] usbcore: registered new interface driver cdc_ncm [ 2.455646] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.462215] ehci-pci: EHCI PCI platform driver [ 2.466726] ehci-platform: EHCI generic platform driver [ 2.472220] ehci-orion: EHCI orion driver [ 2.476462] SPEAr-ehci: EHCI SPEAr driver [ 2.480655] ehci-st: EHCI STMicroelectronics driver [ 2.485706] ehci-exynos: EHCI EXYNOS driver [ 2.490084] ehci-atmel: EHCI Atmel driver [ 2.494254] tegra-ehci: Tegra EHCI driver [ 2.498487] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.504691] ohci-pci: OHCI PCI platform driver [ 2.509208] ohci-platform: OHCI generic platform driver [ 2.514676] SPEAr-ohci: OHCI SPEAr driver [ 2.518888] ohci-st: OHCI STMicroelectronics driver [ 2.523935] ohci-atmel: OHCI Atmel driver [ 2.528888] usbcore: registered new interface driver usb-storage [ 2.537166] imx_usb 2184000.usb: Linked as a consumer to regulator.9 [ 2.549018] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator [ 2.557300] imx_usb 2184200.usb: Linked as a consumer to regulator.0 [ 2.567206] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.572122] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 2.605772] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.611878] hub 1-0:1.0: USB hub found [ 2.615674] hub 1-0:1.0: 1 port detected [ 2.625505] i2c /dev entries driver [ 2.642345] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 2.653030] sdhci: Secure Digital Host Controller Interface driver [ 2.659269] sdhci: Copyright(c) Pierre Ossman [ 2.665674] Synopsys Designware Multimedia Card Interface Driver [ 2.673480] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.680115] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO [ 2.685285] sdhci-esdhc-imx 2194000.usdhc: Got WP GPIO [ 2.690558] sdhci-esdhc-imx 2194000.usdhc: Linked as a consumer to regulator.8 [ 2.730268] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 2.738198] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 2.743371] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 2.748653] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 [ 2.788354] mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 2.796319] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 [ 2.835708] mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.847216] ledtrig-cpu: registered to indicate activity on CPUs [ 2.854089] usbcore: registered new interface driver usbhid [ 2.859721] usbhid: USB HID core driver [ 2.869256] NET: Registered protocol family 10 [ 2.874952] Segment Routing with IPv6 [ 2.878741] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.885222] NET: Registered protocol family 17 [ 2.889725] can: controller area network core (rev 20170425 abi 9) [ 2.896001] NET: Registered protocol family 29 [ 2.900453] can: raw protocol (rev 20170425) [ 2.904727] can: broadcast manager protocol (rev 20170425 t) [ 2.910421] can: netlink gateway (rev 20170425) max_hops=1 [ 2.916367] Key type dns_resolver registered [ 2.921524] cpu cpu0: Linked as a consumer to regulator.4 [ 2.927045] cpu cpu0: Linked as a consumer to regulator.5 [ 2.932507] cpu cpu0: Linked as a consumer to regulator.6 [ 2.938642] ThumbEE CPU extension supported. [ 2.942927] Registering SWP/SWPB emulation handler [ 2.949510] Loading compiled-in X.509 certificates [ 2.973187] imx_thermal tempmon: Commercial CPU temperature grade - max:95C critical:90C passive:85C [ 2.983497] hctosys: unable to open rtc device (rtc0) [ 2.993343] Freeing unused kernel memory: 2048K [ 2.998290] Run /init as init process [ 3.015893] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.055069] mmc2: new DDR MMC card at address 0001 [ 3.064398] mmcblk2: mmc2:0001 MMC04G 3.58 GiB [ 3.070288] mmcblk2boot0: mmc2:0001 MMC04G partition 1 2.00 MiB [ 3.077589] mmcblk2boot1: mmc2:0001 MMC04G partition 2 2.00 MiB [ 3.097481] mmcblk2rpmb: mmc2:0001 MMC04G partition 3 128 KiB, chardev (235:0) Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 3.193756] udevd[88]: starting version 3.2.9 [ 3.199039] random: udevd: uninitialized urandom read (16 bytes read) [ 3.206169] random: udevd: uninitialized urandom read (16 bytes read) [ 3.212728] random: udevd: uninitialized urandom read (16 bytes read) [ 3.220711] hub 1-1:1.0: USB hub found [ 3.226009] hub 1-1:1.0: 4 ports detected [ 3.235704] udevd[88]: specified user 'tss' unknown [ 3.241614] udevd[88]: specified group 'tss' unknown [ 3.257307] udevd[89]: starting eudev-3.2.9 [ 4.070058] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 4.117041] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 4.123498] etnaviv-gpu 130000.gpu: model: GC880, revision: 5106 [ 4.242877] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 4.355986] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 [ 4.484076] sgtl5000 0-000a: Linked as a consumer to regulator.7 [ 4.490216] sgtl5000 0-000a: Linked as a consumer to regulator.8 [ 4.553601] sgtl5000 0-000a: Error reading chip id -6 [ 4.571312] sgtl5000 0-000a: Dropping the link to regulator.7 [ 4.594650] sgtl5000 0-000a: Dropping the link to regulator.8 done Saving random seed: [ 5.128668] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: [ 5.212145] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-882600/environment . /lava-882600/environment / # /lava-882600/bin/lava-test-runner /lava-882600/0 /lava-882600/bin/lava-test-runner /lava-882600/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-882600/0/tests/0_dmes[ 5.786158] g + cat uuid + UUID=882600_1.5.2.3.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 5.825634] [ 5.863325] [ 5.901258] + set +x [ 5.910851] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-882600/environment / # . /lava-882600/environment/lava-882600/bin/lava-test-runner /lava-882600/1 / # /lava-882600/bin/lava-test-runner /lava-882600/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-882600/1/tests/1_boot[ 6.397511] rr + cat uuid + UUID=882600_1.5.2.3.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-882600/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-882600/1/../bin/lava-test-case [ 6.444231] /lava-882600/1/../bin/lava-test-case [ 6.479696] /lava-882600/1/../bin/lava-test-case [ 6.502055] + set +x [ 6.519401] / #