[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.99 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 9729568/tftp-deploy-tw_wos4t/kernel/zImage tftp 0x10000000 9729568/tftp-deploy-tw_wos4t/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9729568/tftp-deploy-tw_wos4t/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 3 MiB/s done Bytes transferred = 8827392 (86b200 hex) => tftp 0x14000000 9729568/tftp-deploy-tw_wos4t/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9729568/tftp-deploy-tw_wos4t/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9729568/tftp-deploy-tw_wos4t/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 2.8 MiB/s done Bytes transferred = 13331716 (cb6d04 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9729568/tftp-deploy-tw_wos4t/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9729568/tftp-deploy-tw_wos4t/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.99 Filename '9729568/tftp-deploy-tw_wos4t/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x86b200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13331652 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.277-cip94-rt29 (KernelCI@build-j1227123-arm-gcc-10-defconfig-preempt-rt-fmp4f) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Wed Mar 22 12:17:26 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') <6>[ 0.000000] bootconsole [ec_imx21] enabled <6>[ 0.000000] Memory policy: Data cache writealloc <6>[ 0.000000] efi: Getting EFI parameters from FDT: <6>[ 0.000000] efi: UEFI not found. <3>[ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring <6>[ 0.000000] cma: Reserved 64 MiB at 0x4c000000 <6>[ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 <5>[ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 938568K/1048576K available (12288K kernel code, 1636K rwdata, 4692K rodata, 2048K init, 406K bss, 44472K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. <6>[ 0.000000] No expedited grace period (rcu_normal_after_boot). <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.000021] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.003147] Console: colour dummy device 80x30 <6>[ 0.271690] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.271701] pid_max: default: 32768 minimum: 301 <6>[ 0.271851] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.271870] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.272593] CPU: Testing write buffer coherency: ok <6>[ 0.272624] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.273066] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.318435] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.326084] rcu: Hierarchical SRCU implementation. <6>[ 0.333250] EFI services will not be available. <6>[ 0.335593] smp: Bringing up secondary CPUs ... <6>[ 0.341358] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.341366] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.342883] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.342890] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.344385] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.344391] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.344531] smp: Brought up 1 node, 4 CPUs <6>[ 0.379711] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.386144] CPU: All CPU(s) started in SVC mode. <6>[ 0.392231] devtmpfs: initialized <6>[ 0.405923] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.411624] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.421121] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.430896] pinctrl core: initialized pinctrl subsystem <6>[ 0.435737] DMI not present or invalid. <6>[ 0.438567] NET: Registered protocol family 16 <6>[ 0.448179] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.455778] cpuidle: using governor menu <6>[ 0.457344] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.475915] vdd1p1: supplied by regulator-dummy <6>[ 0.478571] vdd3p0: supplied by regulator-dummy <6>[ 0.483376] vdd2p5: supplied by regulator-dummy <6>[ 0.488129] vddarm: supplied by regulator-dummy <6>[ 0.493166] vddpu: supplied by regulator-dummy <6>[ 0.497410] vddsoc: supplied by regulator-dummy <6>[ 0.521499] No ATAGs? <6>[ 0.521624] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.529570] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.540441] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.547395] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.561447] Serial: AMBA PL011 UART driver <6>[ 0.566079] console [pstore-1] enabled <6>[ 0.567465] pstore: Registered ramoops as persistent store backend <6>[ 0.573677] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.614345] mxs-dma 110000.dma-apbh: initialized <6>[ 0.626811] vgaarb: loaded <5>[ 0.628143] SCSI subsystem initialized <6>[ 0.631588] usbcore: registered new interface driver usbfs <6>[ 0.636736] usbcore: registered new interface driver hub <6>[ 0.642294] usbcore: registered new device driver usb <6>[ 0.649580] i2c i2c-0: IMX I2C adapter registered <6>[ 0.652518] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.659007] i2c i2c-1: IMX I2C adapter registered <6>[ 0.663042] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.669463] i2c i2c-2: IMX I2C adapter registered <6>[ 0.673571] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.681118] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.684349] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.693769] PTP clock support registered <6>[ 0.698256] EDAC MC: Ver: 3.0.0 <6>[ 0.705257] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.800845] NET: Registered protocol family 2 <6>[ 0.803101] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.810723] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.817637] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.824992] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) <6>[ 0.832058] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.838562] UDP hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.844539] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.851381] NET: Registered protocol family 1 <6>[ 0.856476] RPC: Registered named UNIX socket transport module. <6>[ 0.861867] RPC: Registered udp transport module. <6>[ 0.866827] RPC: Registered tcp transport module. <6>[ 0.871784] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.879118] Trying to unpack rootfs image as initramfs... <6>[ 2.116874] Freeing initrd memory: 13020K <4>[ 2.118713] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.126010] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.137011] Initialise system trusted keyrings <6>[ 2.139185] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.156978] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.161349] NFS: Registering the id_resolver key type <5>[ 2.165571] Key type id_resolver registered <5>[ 2.169972] Key type id_legacy registered <6>[ 2.174297] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.181600] Key type asymmetric registered <5>[ 2.183200] Asymmetric key parser 'x509' registered <6>[ 2.188457] bounce: pool size: 64 pages <6>[ 2.192461] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 2.200079] io scheduler noop registered <6>[ 2.204250] io scheduler deadline registered <6>[ 2.209125] io scheduler cfq registered (default) <6>[ 2.213736] io scheduler mq-deadline registered <6>[ 2.218522] io scheduler kyber registered <6>[ 2.253764] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.258343] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.265502] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.272766] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.293583] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.300501] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <4>[ 2.300726] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.300805] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.300866] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.301006] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 2.301168] PU : no governor for states <6>[ 2.301186] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 2.381638] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.390318] SuperH (H)SCI(F) driver initialized <6>[ 2.393590] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 2.402397] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 2.412919] console [ttymxc1] enabled <6>[ 2.412919] console [ttymxc1] enabled <6>[ 2.417910] bootconsole [ec_imx21] disabled <6>[ 2.417910] bootconsole [ec_imx21] disabled <6>[ 2.428477] msm_serial: driver initialized <6>[ 2.434316] STMicroelectronics ASC driver initialized <6>[ 2.442066] STM32 USART driver initialized <4>[ 2.460384] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.469113] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.476137] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.482930] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.491989] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.499166] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.518281] brd: module loaded <6>[ 2.535987] loop: module loaded <6>[ 2.543727] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.551929] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.560213] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.568670] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.579493] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.586759] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.595825] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.607121] scsi host0: ahci-imx <6>[ 2.611395] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.634935] CAN device driver interface <6>[ 2.640687] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.648019] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.657013] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.666473] pps pps0: new PPS source ptp0 <6>[ 2.700970] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.708742] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.714846] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.721122] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.728357] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.742083] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.749818] usbcore: registered new interface driver pegasus <6>[ 2.755820] usbcore: registered new interface driver asix <6>[ 2.761540] usbcore: registered new interface driver ax88179_178a <6>[ 2.767961] usbcore: registered new interface driver cdc_ether <6>[ 2.774152] usbcore: registered new interface driver smsc75xx <6>[ 2.780245] usbcore: registered new interface driver smsc95xx <6>[ 2.786322] usbcore: registered new interface driver net1080 <6>[ 2.792298] usbcore: registered new interface driver cdc_subset <6>[ 2.798541] usbcore: registered new interface driver zaurus <6>[ 2.804481] usbcore: registered new interface driver cdc_ncm <6>[ 2.814344] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.821149] ehci-pci: EHCI PCI platform driver <6>[ 2.825927] ehci-platform: EHCI generic platform driver <6>[ 2.831820] ehci-orion: EHCI orion driver <6>[ 2.836433] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.840989] ehci-st: EHCI STMicroelectronics driver <6>[ 2.846432] ehci-exynos: EHCI EXYNOS driver <6>[ 2.851154] ehci-atmel: EHCI Atmel driver <6>[ 2.855709] tegra-ehci: Tegra EHCI driver <6>[ 2.860288] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.866766] ohci-pci: OHCI PCI platform driver <6>[ 2.871543] ohci-platform: OHCI generic platform driver <6>[ 2.877401] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.881952] ohci-st: OHCI STMicroelectronics driver <6>[ 2.887374] ohci-atmel: OHCI Atmel driver <6>[ 2.892964] usbcore: registered new interface driver usb-storage <6>[ 2.902199] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.915132] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.925602] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.930780] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.965319] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.971972] hub 1-0:1.0: USB hub found <6>[ 2.976041] hub 1-0:1.0: 1 port detected <6>[ 2.989505] i2c /dev entries driver <6>[ 3.013552] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.026819] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.033271] sdhci: Copyright(c) Pierre Ossman <6>[ 3.040841] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.049803] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.056722] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 3.062166] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 3.067718] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.108122] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 3.115336] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>[ 3.115734] ata1.00: ATA-8: INTEL SSDSA2CW080G3, 4PC10362, max UDMA/133 <6>[ 3.115745] ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 32) <6>[ 3.116188] ata1.00: configured for UDMA/133 <5>[ 3.117038] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW08 0362 PQ: 0 ANSI: 5 <6>[ 3.117819] ata1.00: Enabling discard_zeroes_data <5>[ 3.118069] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) <5>[ 3.118125] sd 0:0:0:0: [sda] Write Protect is off <5>[ 3.118217] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6>[ 3.118829] ata1.00: Enabling discard_zeroes_data <6>[ 3.120193] sda: sda1 sda2 sda3 <6>[ 3.121879] ata1.00: Enabling discard_zeroes_data <5>[ 3.122310] sd 0:0:0:0: [sda] Attached SCSI disk <6>[ 3.184534] mmc0: new high speed SDHC card at address 0001 <6>[ 3.186854] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 3.209268] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 3.214876] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <4>[ 3.216285] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.216292] GPT:7812499 != 30560255 <4>[ 3.216296] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.216300] GPT:7812499 != 30560255 <4>[ 3.216303] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.216353] mmcblk0: p1 p2 p3 <6>[ 3.265344] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.285629] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 3.299313] usbcore: registered new interface driver usbhid <6>[ 3.305159] usbhid: USB HID core driver <6>[ 3.317366] NET: Registered protocol family 10 <6>[ 3.323633] Segment Routing with IPv6 <6>[ 3.327670] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.334657] NET: Registered protocol family 17 <6>[ 3.339393] can: controller area network core (rev 20170425 abi 9) <6>[ 3.345973] NET: Registered protocol family 29 <6>[ 3.350695] can: raw protocol (rev 20170425) <6>[ 3.355302] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.361251] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 3.367578] Key type dns_resolver registered <6>[ 3.373709] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 3.379506] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 3.385351] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 3.392219] ThumbEE CPU extension supported. <5>[ 3.396778] Registering SWP/SWPB emulation handler <5>[ 3.402524] Loading compiled-in X.509 certificates <6>[ 3.409398] pstore: Using compression: deflate <6>[ 3.439547] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.446980] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.456055] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.463545] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 3.471286] hub 1-1:1.0: USB hub found <6>[ 3.475497] hub 1-1:1.0: 3 ports detected <4>[ 3.482417] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.491116] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.498118] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.506486] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.515527] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.522678] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.531832] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 3.542685] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.550092] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.558800] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.566291] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.575357] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.584075] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.591059] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.599287] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.608328] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.615481] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.623602] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.631008] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.639674] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.647163] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.656199] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.664888] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.671872] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.680085] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.689121] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.696273] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.706434] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.714137] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.715426] hctosys: unable to open rtc device (rtc0) <6>[ 3.726903] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.735862] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.743351] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.752448] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.761146] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.768125] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.776430] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.785472] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.792621] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.836038] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.851241] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.926310] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 5.955484] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.985590] Sending DHCP requests ., OK <6>[ 6.029708] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.99 <6>[ 6.038006] IP-Config: Complete: <6>[ 6.041536] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.101.99, mask=255.255.255.0, gw=192.168.101.1 <6>[ 6.052251] host=imx6q-sabrelite-cbg-0, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 6.061219] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 6.061223] nameserver0=192.168.101.1 <6>[ 6.079656] Freeing unused kernel memory: 2048K <6>[ 6.084794] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.228890] udevd[143]: starting version 3.2.9 <5>[ 6.234888] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.241945] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.248774] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.262998] udevd[143]: specified user 'tss' unknown <27>[ 6.268467] udevd[143]: specified group 'tss' unknown <30>[ 6.276415] udevd[144]: starting eudev-3.2.9 <6>[ 7.236313] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.243737] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.257574] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.265494] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.281975] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.291320] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.298414] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.305366] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.305901] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.321175] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.330876] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.338109] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.348017] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.356455] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.363869] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.372962] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.379859] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.388112] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.395745] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.409822] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.427721] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.436582] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <4>[ 7.437795] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.440775] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.440882] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.444089] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.444371] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.444471] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.460627] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.460718] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.462918] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.463003] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.518113] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.545458] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.554946] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.563674] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.570698] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.579513] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.588628] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.595837] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.604276] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.611706] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.623719] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.631229] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.736436] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.746154] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.753428] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.772664] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.781772] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.789225] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.796267] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.803350] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.810702] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.811001] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.815666] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.831191] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.842966] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.850647] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.862749] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.871827] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.878849] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.889913] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.899345] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.906528] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.917537] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.924956] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.938058] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.945805] pwm-backlight backlight-lvds: Dropping the link to regulator.8 done Saving random seed: <5>[ 8.493600] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.601735] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9729568/environment . /lava-9729568/environment / # /lava-9729568/bin/lava-test-runner /lava-9729568/0 /lava-9729568/bin/lava-test-runner /lava-9729568/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-9729568/0/tests/0_dmesg + cat uuid + UUID=9729568_1.5.2.4.1 <8>[ 9.198754] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.251246] <8>[ 9.298454] <8>[ 9.345947] + set +x <8>[ 9.356189] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9729568/environment / # . /lava-9729568/environment/lava-9729568/bin/lava-test-runner /lava-9729568/1 / # /lava-9729568/bin/lava-test-runner /lava-9729568/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-9729568/1/tests/1_bootrr + cat uuid + UUID=9729568_1.5.2.4.5 + set <8>[ 9.857054] +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9729568/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd panel-lvds0 backlight-lcd backlight-lvds /lava-9729568/1/../bin/lava-test-case <8>[ 10.939434] /lava-9729568/1/../bin/lava-test-case <8>[ 10.986610] /lava-9729568/1/../bin/lava-test-case <8>[ 11.015607] + set<8>[ 11.037007] +x / #