Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3023 device /dev/ttyimx6ul-14x14-evk-1 [115200 N81] (Debian GNU/Linux) U-Boot 2019.04-lf-5.4.y_v2019.04+g228843cdf5 (Feb 24 2020 - 11:58:52 +0000) CPU: Freescale i.MX6UL rev1.2 696 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 33C Reset cause: POR Model: Freescale i.MX6 UltraLite 14x14 EVK Board Board: MX6UL 14x14 EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: Warning: ethernet@020b4000 using MAC address from ROM eth1: ethernet@020b4000 [PRIME] Warning: ethernet@02188000 using MAC address from ROM , eth0: ethernet@02188000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 DHCP client bound to address 172.16.1.160 (7360 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1181708/tftp-deploy-u_yz3o1s/kernel/zImage tftp 0x80800000 1181708/tftp-deploy-u_yz3o1s/kernel/zImage Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181708/tftp-deploy-u_yz3o1s/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 5.3 MiB/s done Bytes transferred = 8827392 (86b200 hex) => tftp 0x86800000 1181708/tftp-deploy-u_yz3o1s/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1181708/tftp-deploy-u_yz3o1s/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181708/tftp-deploy-u_yz3o1s/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 4.9 MiB/s done Bytes transferred = 13351593 (cbbaa9 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1181708/tftp-deploy-u_yz3o1s/dtb/imx6ul-14x14-evk.dtb tftp 0x83000000 1181708/tftp-deploy-u_yz3o1s/dtb/imx6ul-14x14-evk.dtb Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181708/tftp-deploy-u_yz3o1s/dtb/imx6ul-14x14-evk.dtb'. Load address: 0x83000000 Loading: *## 3.3 MiB/s done Bytes transferred = 27892 (6cf4 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x86b200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13351529 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 83009cf3 ft_system_setup for mx6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.277-cip94-rt29 (KernelCI@build-j1227123-arm-gcc-10-defconfig-preempt-rt-fmp4f) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Wed Mar 22 12:17:26 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 UltraLite 14x14 EVK Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x02020000 (options '') <6>[ 0.000000] bootconsole [ec_imx6q0] enabled <6>[ 0.000000] Memory policy: Data cache writealloc <6>[ 0.000000] efi: Getting EFI parameters from FDT: <6>[ 0.000000] efi: UEFI not found. <6>[ 0.000000] cma: Reserved 64 MiB at 0x9c000000 <6>[ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 <5>[ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 419144K/524288K available (12288K kernel code, 1636K rwdata, 4692K rodata, 2048K init, 406K bss, 39608K reserved, 65536K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. <6>[ 0.000000] No expedited grace period (rcu_normal_after_boot). <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] Switching to timer-based delay loop, resolution 41ns <6>[ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.000050] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.005597] Console: colour dummy device 80x30 <6>[ 0.225575] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.225602] pid_max: default: 32768 minimum: 301 <6>[ 0.225985] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.226013] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.227725] CPU: Testing write buffer coherency: ok <3>[ 0.228674] /cpus/cpu@0 missing clock-frequency property <6>[ 0.266246] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.274410] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.281886] rcu: Hierarchical SRCU implementation. <6>[ 0.291228] EFI services will not be available. <6>[ 0.293758] smp: Bringing up secondary CPUs ... <6>[ 0.297991] smp: Brought up 1 node, 1 CPU <6>[ 0.302262] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.308684] CPU: All CPU(s) started in SVC mode. <6>[ 0.315597] devtmpfs: initialized <6>[ 0.336099] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.342736] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.351370] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.363031] pinctrl core: initialized pinctrl subsystem <6>[ 0.370568] DMI not present or invalid. <6>[ 0.374393] NET: Registered protocol family 16 <6>[ 0.388234] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.400211] cpuidle: using governor menu <6>[ 0.426734] vdd3p0: supplied by regulator-dummy <6>[ 0.430078] cpu: supplied by regulator-dummy <6>[ 0.435307] vddsoc: supplied by regulator-dummy <6>[ 0.473834] No ATAGs? <6>[ 0.473964] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.481933] hw-breakpoint: maximum watchpoint size is 8 bytes. <4>[ 0.497711] imx6ul-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e4000 debugfs directory <6>[ 0.505204] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.523527] Serial: AMBA PL011 UART driver <6>[ 0.606914] mxs-dma 1804000.dma-apbh: initialized <6>[ 0.623945] vgaarb: loaded <5>[ 0.627142] SCSI subsystem initialized <6>[ 0.629986] usbcore: registered new interface driver usbfs <6>[ 0.634546] usbcore: registered new interface driver hub <6>[ 0.639774] usbcore: registered new device driver usb <6>[ 0.649558] i2c i2c-0: IMX I2C adapter registered <6>[ 0.651723] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.660017] i2c i2c-1: IMX I2C adapter registered <6>[ 0.662249] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.671609] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.674007] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.683490] PTP clock support registered <6>[ 0.688261] EDAC MC: Ver: 3.0.0 <6>[ 0.700346] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.943166] NET: Registered protocol family 2 <6>[ 0.945585] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.953988] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.959728] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.967116] TCP bind hash table entries: 4096 (order: 4, 114688 bytes) <6>[ 0.974081] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.980895] UDP hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.986618] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.993756] NET: Registered protocol family 1 <6>[ 0.999569] RPC: Registered named UNIX socket transport module. <6>[ 1.003964] RPC: Registered udp transport module. <6>[ 1.008904] RPC: Registered tcp transport module. <6>[ 1.013876] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.021818] Trying to unpack rootfs image as initramfs... <6>[ 3.842039] Freeing initrd memory: 13040K <5>[ 3.848894] Initialise system trusted keyrings <6>[ 3.851550] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.888665] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.895039] NFS: Registering the id_resolver key type <5>[ 3.897752] Key type id_resolver registered <5>[ 3.901978] Key type id_legacy registered <6>[ 3.906406] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.919062] Key type asymmetric registered <5>[ 3.920628] Asymmetric key parser 'x509' registered <6>[ 3.925891] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.933407] io scheduler noop registered <6>[ 3.937566] io scheduler deadline registered <6>[ 3.943085] io scheduler cfq registered (default) <6>[ 3.947054] io scheduler mq-deadline registered <6>[ 3.951884] io scheduler kyber registered <4>[ 4.015045] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 4.022629] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 4.030261] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 4.067158] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 4.081671] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 4.299718] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 4.314701] SuperH (H)SCI(F) driver 鹥ѥ���镑5 <6>[ 4.320627] console [ttymxc0] enabled <6>[ 4.320627] console [ttymxc0] enabled <6>[ 4.325638] bootconsole [ec_imx6q0] disabled <6>[ 4.325638] bootconsole [ec_imx6q0] disabled <6>[ 4.338125] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 61, base_baud = 5000000) is a IMX <6>[ 4.350855] msm_serial: driver initialized <6>[ 4.355971] STMicroelectronics ASC driver initialized <6>[ 4.365807] STM32 USART driver initialized <4>[ 4.397353] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 4.405584] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 4.412496] panel-simple panel: Dropping the link to regulator.0 <6>[ 4.455128] brd: module loaded <6>[ 4.487987] loop: module loaded <6>[ 4.532312] CAN device driver interface <6>[ 4.539672] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 4.548199] fec 20b4000.ethernet: 20b4000.ethernet supply phy not found, using dummy regulator <6>[ 4.557449] fec 20b4000.ethernet: Linked as a consumer to regulator.0 <6>[ 4.565861] pps pps0: new PPS source ptp0 <6>[ 4.689964] fec 20b4000.ethernet eth0: registered PHC device 0 <4>[ 4.698100] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 4.707363] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 4.715823] pps pps1: new PPS source ptp1 <6>[ 6.542744] fec 2188000.ethernet eth1: registered PHC device 1 <6>[ 6.552238] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 6.558370] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 6.564905] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 6.572242] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 6.594146] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 6.602138] usbcore: registered new interface driver pegasus <6>[ 6.608281] usbcore: registered new interface driver asix <6>[ 6.614206] usbcore: registered new interface driver ax88179_178a <6>[ 6.620764] usbcore: registered new interface driver cdc_ether <6>[ 6.627064] usbcore: registered new interface driver smsc75xx <6>[ 6.633346] usbcore: registered new interface driver smsc95xx <6>[ 6.639523] usbcore: registered new interface driver net1080 <6>[ 6.645635] usbcore: registered new interface driver cdc_subset <6>[ 6.652016] usbcore: registered new interface driver zaurus <6>[ 6.658169] usbcore: registered new interface driver cdc_ncm <6>[ 6.672193] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 6.679027] ehci-pci: EHCI PCI platform driver <6>[ 6.683951] ehci-platform: EHCI generic platform driver <6>[ 6.690264] ehci-orion: EHCI orion driver <6>[ 6.695401] SPEAr-ehci: EHCI SPEAr driver <6>[ 6.700243] ehci-st: EHCI STMicroelectronics driver <6>[ 6.706003] ehci-exynos: EHCI EXYNOS driver <6>[ 6.711061] ehci-atmel: EHCI Atmel driver <6>[ 6.715891] tegra-ehci: Tegra EHCI driver <6>[ 6.721054] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 6.727622] ohci-pci: OHCI PCI platform driver <6>[ 6.732570] ohci-platform: OHCI generic platform driver <6>[ 6.738828] SPEAr-ohci: OHCI SPEAr driver <6>[ 6.743731] ohci-st: OHCI STMicroelectronics driver <6>[ 6.749446] ohci-atmel: OHCI Atmel driver <6>[ 6.756568] usbcore: registered new interface driver usb-storage <4>[ 6.768496] imx_usb 2184000.usb: 2184000.usb supply vbus not found, using dummy regulator <6>[ 6.777248] imx_usb 2184000.usb: Linked as a consumer to regulator.0 <4>[ 6.794062] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator <6>[ 6.802850] imx_usb 2184200.usb: Linked as a consumer to regulator.0 <6>[ 6.815451] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 6.820732] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 6.850504] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 6.858939] hub 1-0:1.0: USB hub found <6>[ 6.863131] hub 1-0:1.0: 1 port detected <6>[ 6.887955] i2c /dev entries driver <6>[ 6.934961] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 6.956000] sdhci: Secure Digital Host Controller Interface driver <6>[ 6.962494] sdhci: Copyright(c) Pierre Ossman <6>[ 6.973320] Synopsys Designware Multimedia Card Interface Driver <6>[ 6.985306] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 6.994123] sdhci-esdhc-imx 2190000.usdhc: Got CD GPIO <6>[ 6.999996] sdhci-esdhc-imx 2190000.usdhc: Linked as a consumer to regulator.4 <6>[ 7.042469] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA <6>[ 7.086017] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA <6>[ 7.113383] usbcore: registered new interface driver usbhid <6>[ 7.119256] usbhid: USB HID core driver <4>[ 7.131293] mmc1: host does not support reading read-only switch, assuming write-enable <6>[ 7.156185] NET: Registered protocol family 10 <6>[ 7.161795] mmc1: new high speed SDHC card at address aaaa <6>[ 7.164554] mmcblk1: mmc1:aaaa SS16G 14.8 GiB <6>[ 7.171679] mmcblk1: p1 p2 <6>[ 7.187544] Segment Routing with IPv6 <6>[ 7.191874] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.200162] NET: Registered protocol family 17 <6>[ 7.205055] can: controller area network core (rev 20170425 abi 9) <6>[ 7.211873] NET: Registered protocol family 29 <6>[ 7.216628] can: raw protocol (rev 20170425) <6>[ 7.221212] can: broadcast manager protocol (rev 20170425 t) <6>[ 7.227207] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 7.234531] Key type dns_resolver registered <6>[ 7.242680] cpu cpu0: Linked as a consumer to regulator.2 <6>[ 7.248664] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 7.256554] ThumbEE CPU extension supported. <5>[ 7.261378] Registering SWP/SWPB emulation handler <5>[ 7.268152] Loading compiled-in X.509 certificates <4>[ 7.319221] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 7.329528] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 7.337405] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 7.348615] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 7.356844] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 7.363663] panel-simple panel: Dropping the link to regulator.0 <6>[ 7.375380] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 7.387409] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 7.397762] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 7.405636] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 7.416838] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 7.425041] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 7.431858] panel-simple panel: Dropping the link to regulator.0 <4>[ 7.441019] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 7.451373] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 7.459230] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 7.470749] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 7.478865] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 7.485676] panel-simple panel: Dropping the link to regulator.0 <6>[ 7.494372] hctosys: unable to open rtc device (rtc0) <6>[ 7.611805] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) <6>[ 7.628883] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 7.741305] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:02: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:02, irq=POLL) <6>[ 7.758434] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready <6>[ 10.734469] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 10.763958] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 10.792961] Sending DHCP requests .., OK <6>[ 13.198476] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.160 <6>[ 13.206621] IP-Config: Complete: <6>[ 13.210155] device=eth0, hwaddr=00:04:9f:05:20:41, ipaddr=172.16.1.160, mask=255.255.255.0, gw=172.16.1.4 <6>[ 13.220756] host=172.16.1.160, domain=example.org, nis-domain=(none) <6>[ 13.228052] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 13.228070] nameserver0=172.16.1.4 <6>[ 13.250611] Freeing unused kernel memory: 2048K <6>[ 13.255801] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 13.566031] udevd[136]: starting version 3.2.9 <5>[ 13.573020] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.580300] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.588396] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 13.611295] udevd[136]: specified user 'tss' unknown <27>[ 13.617006] udevd[136]: specified group 'tss' unknown <30>[ 13.632990] udevd[137]: starting eudev-3.2.9 <4>[ 16.189313] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 16.199624] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 16.242092] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 16.319543] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 16.342997] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 16.349774] panel-simple panel: Dropping the link to regulator.0 <6>[ 16.542207] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 16.549114] [drm] No driver support for vblank timestamp query. <6>[ 16.583075] fsl-quadspi 21e0000.qspi: n25q256a (32768 Kbytes) <4>[ 16.598761] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 16.598965] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 16.599147] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 16.604981] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 16.605156] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 16.625096] panel-simple panel: Dropping the link to regulator.0 <3>[ 16.849205] mxsfb 21c8000.lcdif: Failed to create outputs <4>[ 16.857547] pwm-backlight backlight-display: backlight-display supply power not found, using dummy regulator <6>[ 16.875416] pwm-backlight backlight-display: Linked as a consumer to regulator.0 <6>[ 16.910870] pwm-backlight backlight-display: Dropping the link to regulator.0 <4>[ 16.971477] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 16.979592] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 17.025511] panel-simple panel: Dropping the link to regulator.0 <6>[ 17.067190] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 17.089009] [drm] No driver support for vblank timestamp query. <3>[ 17.103685] mxsfb 21c8000.lcdif: Failed to create outputs done Saving random seed: <5>[ 18.652344] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 18.819470] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1181708/environment . /lava-1181708/environment / # /lava-1181708/bin/lava-test-runner /lava-1181708/0 /lava-1181708/bin/lava-test-runner /lava-1181708/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1181708/0/tests/0_dmesg + cat uuid + UUID=1181708_1.5.2.4.1<8>[ 24.737319] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 24.818601] <8>[ 24.893519] <8>[ 24.967228] + set +x <8>[ 24.978971] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1181708/environment / # . /lava-1181708/environment/lava-1181708/bin/lava-test-runner /lava-1181708/1 / # /lava-1181708/bin/lava-test-runner /lava-1181708/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1181708/1/tests/1_bootrr + cat uuid + UUID=1181708_1.5.2.4.5<8>[ 30.770699] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1181708/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-display sound panel 21c8000.lcdif /lava-1181708/1/../bin/lava-test-case <8>[ 31.897120] /lava-1181708/1/../bin/lava-test-case <8>[ 31.966985] /lava-1181708/1/../bin/lava-test-case <8>[ 32.007797] + set +x <8>[ 32.038130] / #