[Enter `^Ec?' for help] � U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10419837/tftp-deploy-p9hhiqw7/kernel/zImage tftp 0x10000000 10419837/tftp-deploy-p9hhiqw7/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '10419837/tftp-deploy-p9hhiqw7/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 10.9 MiB/s done Bytes transferred = 8827392 (86b200 hex) => tftp 0x14000000 10419837/tftp-deploy-p9hhiqw7/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10419837/tftp-deploy-p9hhiqw7/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '10419837/tftp-deploy-p9hhiqw7/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 11.1 MiB/s done Bytes transferred = 9420910 (8fc06e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10419837/tftp-deploy-p9hhiqw7/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10419837/tftp-deploy-p9hhiqw7/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '10419837/tftp-deploy-p9hhiqw7/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.4 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10419837/extract-nfsrootfs-38m_mwsi,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10419837/extract-nfsrootfs-38m_mwsi,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x86b200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9420846 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.280-cip96-rt30 (KernelCI@build-j1546525-arm-gcc-10-defconfig-preempt-rt-2psp7) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Tue May 23 00:52:31 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10419837/extract-nfsrootfs-38m_mwsi,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 942384K/1048576K available (12288K kernel code, 1636K rwdata, 4692K rodata, 2048K init, 406K bss, 40656K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. [ 0.000000] No expedited grace period (rcu_normal_after_boot). [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000021] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003097] Console: colour dummy device 80x30 [ 0.003259] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003268] pid_max: default: 32768 minimum: 301 [ 0.003420] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003439] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.004155] CPU: Testing write buffer coherency: ok [ 0.004185] CPU0: Spectre v2: using BPIALL workaround [ 0.004637] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005602] Setting up static identity map for 0x10300000 - 0x103000a0 [ 0.007410] rcu: Hierarchical SRCU implementation. [ 0.011383] EFI services will not be available. [ 0.011810] smp: Bringing up secondary CPUs ... [ 0.013250] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.013257] CPU1: Spectre v2: using BPIALL workaround [ 0.014807] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.014813] CPU2: Spectre v2: using BPIALL workaround [ 0.016347] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.016352] CPU3: Spectre v2: using BPIALL workaround [ 0.016502] smp: Brought up 1 node, 4 CPUs [ 0.016534] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.016543] CPU: All CPU(s) started in SVC mode. [ 0.017789] devtmpfs: initialized [ 0.029746] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.030393] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.030420] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.033728] pinctrl core: initialized pinctrl subsystem [ 0.036011] DMI not present or invalid. [ 0.036992] NET: Registered protocol family 16 [ 0.043204] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.046686] cpuidle: using governor menu [ 0.046947] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.060804] vdd1p1: supplied by regulator-dummy [ 0.061559] vdd3p0: supplied by regulator-dummy [ 0.062315] vdd2p5: supplied by regulator-dummy [ 0.063059] vddarm: supplied by regulator-dummy [ 0.064062] vddpu: supplied by regulator-dummy [ 0.064576] vddsoc: supplied by regulator-dummy [ 0.084505] No ATAGs? [ 0.084643] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.084661] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.089361] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory [ 0.089703] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.096980] Serial: AMBA PL011 UART driver [ 0.100153] console [pstore-1] enabled [ 0.100400] pstore: Registered ramoops as persistent store backend [ 0.100417] ramoops: attached 0x10000@0x30000000, ecc: 0/0 [ 0.136086] mxs-dma 110000.dma-apbh: initialized [ 0.146518] vgaarb: loaded [ 0.147768] SCSI subsystem initialized [ 0.148376] usbcore: registered new interface driver usbfs [ 0.148459] usbcore: registered new interface driver hub [ 0.148528] usbcore: registered new device driver usb [ 0.150576] i2c i2c-0: IMX I2C adapter registered [ 0.150605] i2c i2c-0: can't use DMA, using PIO instead. [ 0.151557] i2c i2c-1: IMX I2C adapter registered [ 0.151582] i2c i2c-1: can't use DMA, using PIO instead. [ 0.152339] i2c i2c-2: IMX I2C adapter registered [ 0.152363] i2c i2c-2: can't use DMA, using PIO instead. [ 0.154445] pps_core: LinuxPPS API ver. 1 registered [ 0.154462] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.154497] PTP clock support registered [ 0.154839] EDAC MC: Ver: 3.0.0 [ 0.158805] clocksource: Switched to clocksource mxc_timer1 [ 0.256995] NET: Registered protocol family 2 [ 0.257500] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.258689] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes) [ 0.258755] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.258972] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) [ 0.259370] TCP: Hash tables configured (established 8192 bind 8192) [ 0.259667] UDP hash table entries: 512 (order: 3, 32768 bytes) [ 0.259755] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) [ 0.260075] NET: Registered protocol family 1 [ 0.260871] RPC: Registered named UNIX socket transport module. [ 0.260889] RPC: Registered udp transport module. [ 0.260902] RPC: Registered tcp transport module. [ 0.260915] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.261569] Trying to unpack rootfs image as initramfs... [ 1.060164] Freeing initrd memory: 9204K [ 1.060601] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 1.060955] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.063897] Initialise system trusted keyrings [ 1.064272] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.076219] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.077429] NFS: Registering the id_resolver key type [ 1.077629] Key type id_resolver registered [ 1.077646] Key type id_legacy registered [ 1.077722] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.080502] Key type asymmetric registered [ 1.080526] Asymmetric key parser 'x509' registered [ 1.080673] bounce: pool size: 64 pages [ 1.080733] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.080753] io scheduler noop registered [ 1.080770] io scheduler deadline registered [ 1.081144] io scheduler cfq registered (default) [ 1.081164] io scheduler mq-deadline registered [ 1.081182] io scheduler kyber registered [ 1.111602] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 1.111732] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 1.111969] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 1.112081] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 1.125838] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 1.125866] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 1.131418] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 1.131516] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 1.131589] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 1.131759] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 [ 1.131922] PU : no governor for states [ 1.131952] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 1.214908] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.220220] SuperH (H)SCI(F) driver initialized [ 1.221524] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX [ 1.222772] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX [ 2.147543] console [ttymxc1] enabled [ 2.152923] msm_serial: driver initialized [ 2.157373] STMicroelectronics ASC driver initialized [ 2.164801] STM32 USART driver initialized [ 2.182857] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.191318] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.198076] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.204611] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.213432] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.220362] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.239695] brd: module loaded [ 2.257521] loop: module loaded [ 2.265080] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.273021] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.281042] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.289238] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.298916] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.305916] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.314723] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.325690] scsi host0: ahci-imx [ 2.329730] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 [ 2.352968] CAN device driver interface [ 2.358417] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.365508] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 2.374234] fec 2188000.ethernet: Linked as a consumer to regulator.0 [ 2.383422] pps pps0: new PPS source ptp0 [ 2.409390] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.416846] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.422693] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.428709] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.435682] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.449028] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.456496] usbcore: registered new interface driver pegasus [ 2.462241] usbcore: registered new interface driver asix [ 2.467702] usbcore: registered new interface driver ax88179_178a [ 2.473865] usbcore: registered new interface driver cdc_ether [ 2.479797] usbcore: registered new interface driver smsc75xx [ 2.485624] usbcore: registered new interface driver smsc95xx [ 2.491438] usbcore: registered new interface driver net1080 [ 2.497158] usbcore: registered new interface driver cdc_subset [ 2.503145] usbcore: registered new interface driver zaurus [ 2.508890] usbcore: registered new interface driver cdc_ncm [ 2.518438] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.524984] ehci-pci: EHCI PCI platform driver [ 2.529502] ehci-platform: EHCI generic platform driver [ 2.535128] ehci-orion: EHCI orion driver [ 2.539462] SPEAr-ehci: EHCI SPEAr driver [ 2.543749] ehci-st: EHCI STMicroelectronics driver [ 2.548973] ehci-exynos: EHCI EXYNOS driver [ 2.553439] ehci-atmel: EHCI Atmel driver [ 2.557718] tegra-ehci: Tegra EHCI driver [ 2.562050] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.568265] ohci-pci: OHCI PCI platform driver [ 2.572787] ohci-platform: OHCI generic platform driver [ 2.578366] SPEAr-ohci: OHCI SPEAr driver [ 2.582673] ohci-st: OHCI STMicroelectronics driver [ 2.587826] ohci-atmel: OHCI Atmel driver [ 2.593126] usbcore: registered new interface driver usb-storage [ 2.602100] imx_usb 2184000.usb: Linked as a consumer to regulator.9 [ 2.614876] imx_usb 2184200.usb: Linked as a consumer to regulator.14 [ 2.625090] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.630028] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 2.658850] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.665301] hub 1-0:1.0: USB hub found [ 2.669114] hub 1-0:1.0: 1 port detected [ 2.670381] ata1: SATA link down (SStatus 0 SControl 300) [ 2.670424] ahci-imx 2200000.sata: no device found, disabling link. [ 2.670432] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 2.701131] i2c /dev entries driver [ 2.724755] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 2.737669] sdhci: Secure Digital Host Controller Interface driver [ 2.743862] sdhci: Copyright(c) Pierre Ossman [ 2.751216] Synopsys Designware Multimedia Card Interface Driver [ 2.759929] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.766563] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 2.771759] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 2.777050] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 [ 2.817070] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 2.825938] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 2.831439] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 [ 2.872398] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.883049] mmc0: new high speed SDHC card at address aaaa [ 2.890579] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 2.892707] usbcore: registered new interface driver usbhid [ 2.892712] usbhid: USB HID core driver [ 2.900902] NET: Registered protocol family 10 [ 2.902510] Segment Routing with IPv6 [ 2.902627] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.903453] NET: Registered protocol family 17 [ 2.903474] can: controller area network core (rev 20170425 abi 9) [ 2.903604] NET: Registered protocol family 29 [ 2.903616] can: raw protocol (rev 20170425) [ 2.903626] can: broadcast manager protocol (rev 20170425 t) [ 2.903644] can: netlink gateway (rev 20170425) max_hops=1 [ 2.904229] Key type dns_resolver registered [ 2.905894] cpu cpu0: Linked as a consumer to regulator.4 [ 2.905998] cpu cpu0: Linked as a consumer to regulator.5 [ 2.906122] cpu cpu0: Linked as a consumer to regulator.6 [ 2.907354] ThumbEE CPU extension supported. [ 2.907374] Registering SWP/SWPB emulation handler [ 2.908945] Loading compiled-in X.509 certificates [ 2.910822] pstore: Using compression: deflate [ 2.937406] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.937517] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.939579] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.939671] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.941606] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.941684] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.941785] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.943309] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.943380] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.943480] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.945806] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 2.947028] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.947121] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.948727] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.948929] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.950813] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.950889] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.950993] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.952509] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.952603] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.952704] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.954009] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.954094] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.955598] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.955686] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.957453] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.957543] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.957644] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.959228] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.959299] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.959400] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.962685] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 2.963723] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.963813] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.965468] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.965555] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.967373] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.967467] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.967569] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.968968] hctosys: unable to open rtc device (rtc0) [ 2.970004] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.970091] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.970220] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.988826] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.079574] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.079730] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.248968] hub 1-1:1.0: USB hub found [ 3.258801] hub 1-1:1.0: 3 ports detected [ 3.329066] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.336222] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.345875] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.355208] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.364050] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.372489] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.379221] panel-simple panel-lcd: Dropping the link to regulator.0 [ 3.387157] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.395938] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.402837] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 3.432588] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.440012] GPT:7812499 != 31116287 [ 3.443514] GPT:Alternate GPT header not at the end of the disk. [ 3.449535] GPT:7812499 != 31116287 [ 3.453032] GPT: Use GNU Parted to correct GPT errors. [ 3.458227] mmcblk0: p1 p2 p3 [ 3.463567] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.470721] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.479358] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.486586] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.495362] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.503796] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.510524] panel-simple panel-lcd: Dropping the link to regulator.0 [ 3.518434] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.527219] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.534120] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 6.169658] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.198850] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.228846] Sending DHCP requests ., OK [ 6.282942] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 [ 6.290982] IP-Config: Complete: [ 6.294250] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 [ 6.304718] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) [ 6.312582] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.312591] nameserver0=192.168.201.1 [ 6.330655] Freeing unused kernel memory: 2048K [ 6.335486] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 [ 7.704625] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 [ 7.722776] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.730276] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.747289] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.754599] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.774197] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.786325] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.793137] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.809039] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.821560] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.828516] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.843945] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.853352] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.861304] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.891139] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) [ 7.901026] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.907816] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.915064] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.926383] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.935541] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.948081] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.949101] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.949114] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.974369] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.988213] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.994453] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 8.001533] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 8.016878] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 8.023073] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 8.023238] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 8.023337] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 8.055466] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 [ 8.064807] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 8.072065] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 8.089666] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 8.099019] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 8.105758] panel-simple panel-lcd: Dropping the link to regulator.0 [ 8.117245] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 8.126766] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 8.133760] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 8.148585] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 8.155982] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 8.342709] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 8.349970] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 8.369815] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 8.379301] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 8.386282] panel-simple panel-lcd: Dropping the link to regulator.0 [ 8.400673] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 8.410009] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 8.416970] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 8.429390] sgtl5000 0-000a: Linked as a consumer to regulator.7 [ 8.436607] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 8.443724] sgtl5000 0-000a: Linked as a consumer to regulator.8 [ 8.450110] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 8.451423] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 8.457533] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 8.497121] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 8.507163] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 8.523198] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 8.534637] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 8.541403] panel-simple panel-lcd: Dropping the link to regulator.0 [ 8.558270] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 8.570640] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 8.577573] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 8.591077] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 8.601477] pwm-backlight backlight-lcd: Dropping the link to regulator.8 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:13 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.33 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-3 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 10.062151] systemd[1]: System time before build time, advancing clock. [ 10.107683] cgroup: cgroup2: unknown option "memory_recursiveprot" [ 10.125645] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 10.149501] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 10.192065] systemd[1]: Set hostname to . [ 11.184142] systemd[1]: Queued start job for default target Graphical Interface. [ 11.193635] random: systemd: uninitialized urandom read (16 bytes read) [ 11.200464] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 11.212837] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 11.222237] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 11.259280] random: systemd: uninitialized urandom read (16 bytes read) [ 11.267391] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 11.309288] random: systemd: uninitialized urandom read (16 bytes read) [ 11.317391] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 11.360475] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 11.400165] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 11.440137] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 11.479622] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.491837] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 11.530090] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 11.569550] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 11.609366] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 11.639542] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 11.680550] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 11.757550] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 11.768004] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 11.811265] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 11.851995] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 11.893620] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 11.930856] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 11.980398] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 11.989749] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 12.003195] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 12.043532] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 12.118903] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 12.163934] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 12.199480] random: systemd: uninitialized urandom read (16 bytes read) [ 12.210529] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 12.249500] random: systemd: uninitialized urandom read (16 bytes read) [ 12.260514] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 12.315683] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 12.325538] random: systemd: uninitialized urandom read (16 bytes read) [ 12.340575] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.387638] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.423202] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 12.463076] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 12.505869] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 12.540038] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 12.581647] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 12.643305] systemd[1]: modprobe@configfs.service: Succeeded. [ 12.650655] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 12.691657] systemd[1]: modprobe@drm.service: Succeeded. [ 12.698644] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 12.742275] systemd[1]: modprobe@fuse.service: Succeeded. [ 12.749335] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 12.790012] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create[ 13.034595] systemd-journald[203]: Received client request to flush runtime journal. System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. [ 13.450310] random: systemd: uninitialized urandom read (16 bytes read) Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ 13.555027] random: systemd-journal: uninitialized urandom read (16 bytes read) [ 13.570095] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ 14.148936] random: crng init done [ 14.152432] random: 48 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started User Login Management. [ OK ] Started Getty on tty1. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.280-cip96-rt30 #1 SMP PREEMPT RT Tue May 23 00:52:31 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10419837/extract-nfsrootfs-38m_mwsi' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10419837/extract-nfsrootfs-38m_mwsi' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10419837/environment . /lava-10419837/environment / # /lava-10419837/bin/lava-test-runner /lava-10419837/0 /lava-10419837/bin/lava-test-runner /lava-10419837/0 + export TESTRUN_ID=0_dmesg + cd /lava-10419837/0/tests/0_dmesg + cat uuid + UUID=10419837_1.6.2.4.1 [ 27.819399] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 27.940288] [ 28.041880] [ 28.147556] + set[ 28.157121] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10419837/environment / # . /lava-10419837/environment/lava-10419837/bin/lava-test-runner /lava-10419837/1 / # /lava-10419837/bin/lava-test-runner /lava-10419837/1 + export TESTRUN_ID=1_bootrr + cd /lava-10419837/1/tests/1_bootrr + cat uuid + UUID=10419837_1.6.2.4.5[ 28.778356] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10419837/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds panel-lcd panel-lvds0 backlight-lcd /lava-10419837/1/../bin/lava-test-case [ 29.959269] /lava-10419837/1/../bin/lava-test-case [ 30.048704] /lava-10419837/1/../bin/lava-test-case [ 30.104605] + set[ 30.138388] +x / #