[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11829289/tftp-deploy-4kpu2_60/kernel/zImage tftp 0x10000000 11829289/tftp-deploy-4kpu2_60/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '11829289/tftp-deploy-4kpu2_60/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.8 MiB/s done Bytes transferred = 8741376 (856200 hex) => tftp 0x14000000 11829289/tftp-deploy-4kpu2_60/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11829289/tftp-deploy-4kpu2_60/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '11829289/tftp-deploy-4kpu2_60/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 5.8 MiB/s done Bytes transferred = 13337720 (cb8478 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11829289/tftp-deploy-4kpu2_60/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11829289/tftp-deploy-4kpu2_60/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '11829289/tftp-deploy-4kpu2_60/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x856200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13337656 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.295-cip103-rt33 (KernelCI@build-j75714-arm-gcc-10-defconfig-vlxrl) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Oct 20 13:57:43 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939120K/1048576K available (12288K kernel code, 1598K rwdata, 4684K rodata, 2048K init, 394K bss, 43920K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1599 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021358] Console: colour dummy device 80x30 <6>[ 0.023240] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033656] CPU: Testing write buffer coherency: ok <6>[ 0.038790] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044087] pid_max: default: 32768 minimum: 301 <6>[ 0.049093] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055856] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.064017] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069761] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077453] rcu: Hierarchical SRCU implementation. <6>[ 0.084219] EFI services will not be available. <6>[ 0.086471] smp: Bringing up secondary CPUs ... <6>[ 0.091853] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091858] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.103184] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.103190] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114385] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114390] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124730] smp: Brought up 1 node, 4 CPUs <6>[ 0.128982] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135398] CPU: All CPU(s) started in SVC mode. <6>[ 0.141349] devtmpfs: initialized <6>[ 0.151051] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156516] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166258] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175828] pinctrl core: initialized pinctrl subsystem <6>[ 0.180087] DMI not present or invalid. <6>[ 0.183407] NET: Registered protocol family 16 <6>[ 0.190771] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197428] cpuidle: using governor menu <6>[ 0.199417] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214430] vdd1p1: supplied by regulator-dummy <6>[ 0.216902] vdd3p0: supplied by regulator-dummy <6>[ 0.221628] vdd2p5: supplied by regulator-dummy <6>[ 0.226476] vddarm: supplied by regulator-dummy <6>[ 0.231367] vddpu: supplied by regulator-dummy <6>[ 0.235804] vddsoc: supplied by regulator-dummy <6>[ 0.254485] No ATAGs? <6>[ 0.254616] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262571] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.272035] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278907] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290746] Serial: AMBA PL011 UART driver <6>[ 0.294564] console [pstore-1] enabled <6>[ 0.296419] pstore: Registered ramoops as persistent store backend <6>[ 0.302706] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.331193] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340656] vgaarb: loaded <5>[ 0.341586] SCSI subsystem initialized <6>[ 0.345223] usbcore: registered new interface driver usbfs <6>[ 0.350554] usbcore: registered new interface driver hub <6>[ 0.356139] usbcore: registered new device driver usb <6>[ 0.362656] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366355] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372491] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376878] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382877] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387409] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394536] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.398188] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407613] PTP clock support registered <6>[ 0.412002] EDAC MC: Ver: 3.0.0 <6>[ 0.417901] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.480523] NET: Registered protocol family 2 <6>[ 0.482722] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490286] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.497196] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.504592] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.511342] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.518014] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.524001] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.530764] NET: Registered protocol family 1 <6>[ 0.535770] RPC: Registered named UNIX socket transport module. <6>[ 0.541394] RPC: Registered udp transport module. <6>[ 0.546324] RPC: Registered tcp transport module. <6>[ 0.551296] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.558472] Trying to unpack rootfs image as initramfs... <6>[ 1.673417] Freeing initrd memory: 13028K <4>[ 1.675338] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.682660] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.692622] Initialise system trusted keyrings <6>[ 1.695613] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.708071] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.712050] NFS: Registering the id_resolver key type <5>[ 1.716652] Key type id_resolver registered <5>[ 1.721089] Key type id_legacy registered <6>[ 1.725366] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.732093] Key type asymmetric registered <5>[ 1.734286] Asymmetric key parser 'x509' registered <6>[ 1.739499] bounce: pool size: 64 pages <6>[ 1.743549] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.751182] io scheduler noop registered <6>[ 1.755338] io scheduler deadline registered <6>[ 1.760096] io scheduler cfq registered (default) <6>[ 1.764821] io scheduler mq-deadline registered <6>[ 1.769624] io scheduler kyber registered <6>[ 1.795665] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.800241] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.807315] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.814655] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.834923] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.838351] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.846130] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.852359] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.860279] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.867939] PU : no governor for states <6>[ 1.869860] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.873934] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.946491] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.953826] SuperH (H)SCI(F) driver initialized <6>[ 1.956677] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.965435] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.976400] console [ttymxc1] enabled <6>[ 1.976400] console [ttymxc1] enabled <6>[ 1.981401] bootconsole [ec_imx21] disabled <6>[ 1.981401] bootconsole [ec_imx21] disabled <6>[ 1.991521] msm_serial: driver initialized <6>[ 1.997695] STMicroelectronics ASC driver initialized <6>[ 2.004913] STM32 USART driver initialized <4>[ 2.020098] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.028798] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.035791] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.042572] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.051604] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.058778] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.073471] brd: module loaded <6>[ 2.083518] loop: module loaded <6>[ 2.090145] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.098368] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.106644] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.115106] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.125886] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.133169] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.142246] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.153052] scsi host0: ahci-imx <6>[ 2.157106] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.176090] CAN device driver interface <6>[ 2.181460] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.188569] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.197504] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.206603] pps pps0: new PPS source ptp0 <6>[ 2.237463] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.244903] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.251024] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.257270] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.264516] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.276218] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.283946] usbcore: registered new interface driver pegasus <6>[ 2.289936] usbcore: registered new interface driver asix <6>[ 2.295635] usbcore: registered new interface driver ax88179_178a <6>[ 2.302046] usbcore: registered new interface driver cdc_ether <6>[ 2.308211] usbcore: registered new interface driver smsc75xx <6>[ 2.314265] usbcore: registered new interface driver smsc95xx <6>[ 2.320328] usbcore: registered new interface driver net1080 <6>[ 2.326291] usbcore: registered new interface driver cdc_subset <6>[ 2.332527] usbcore: registered new interface driver zaurus <6>[ 2.338451] usbcore: registered new interface driver cdc_ncm <6>[ 2.347294] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.354121] ehci-pci: EHCI PCI platform driver <6>[ 2.358895] ehci-platform: EHCI generic platform driver <6>[ 2.364679] ehci-orion: EHCI orion driver <6>[ 2.369200] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.373667] ehci-st: EHCI STMicroelectronics driver <6>[ 2.379024] ehci-exynos: EHCI EXYNOS driver <6>[ 2.383662] ehci-atmel: EHCI Atmel driver <6>[ 2.388148] tegra-ehci: Tegra EHCI driver <6>[ 2.392644] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.399125] ohci-pci: OHCI PCI platform driver <6>[ 2.403878] ohci-platform: OHCI generic platform driver <6>[ 2.409649] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.414123] ohci-st: OHCI STMicroelectronics driver <6>[ 2.419480] ohci-atmel: OHCI Atmel driver <6>[ 2.424746] usbcore: registered new interface driver usb-storage <6>[ 2.433336] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.445396] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.455549] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.460743] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.489370] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.495069] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.497937] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.501634] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.515024] hub 1-0:1.0: USB hub found <6>[ 2.519125] hub 1-0:1.0: 1 port detected <6>[ 2.529669] i2c /dev entries driver <6>[ 2.548077] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.559530] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.565979] sdhci: Copyright(c) Pierre Ossman <6>[ 2.572910] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.581193] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.588035] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.593474] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.598992] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.638839] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.646857] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.652400] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.692220] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.703645] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.710961] usbcore: registered new interface driver usbhid <6>[ 2.716836] usbhid: USB HID core driver <6>[ 2.726971] NET: Registered protocol family 10 <6>[ 2.732816] mmc0: new high speed SDHC card at address aaaa <6>[ 2.732819] Segment Routing with IPv6 <6>[ 2.732894] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.740269] mmcblk0: mmc0:aaaa SL16G 14.8 GiB <6>[ 2.743167] NET: Registered protocol family 17 <6>[ 2.758244] can: controller area network core (rev 20170425 abi 9) <6>[ 2.764770] NET: Registered protocol family 29 <6>[ 2.769502] can: raw protocol (rev 20170425) <6>[ 2.774043] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.779995] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.786216] Key type dns_resolver registered <6>[ 2.791841] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.797564] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.803339] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.809859] ThumbEE CPU extension supported. <5>[ 2.814407] Registering SWP/SWPB emulation handler <6>[ 2.817945] usb 1-1: new high-speed USB device number 2 using ci_hdrc <5>[ 2.826483] Loading compiled-in X.509 certificates <4>[ 2.832016] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.833108] pstore: Using compression: deflate <4>[ 2.839754] GPT:29296874 != 31116287 <4>[ 2.839763] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.854619] GPT:29296874 != 31116287 <6>[ 2.857195] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 2.858509] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.858571] mmcblk0: p1 p2 p3 <6>[ 2.865900] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.883194] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.890690] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.899339] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.908027] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.915041] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.922863] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.931907] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.939045] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.947620] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.958144] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.965524] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.973799] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.981332] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.989882] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.998567] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.005544] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.013313] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.022338] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.029509] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.037263] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.044689] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.052825] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.060559] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.069128] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.077785] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.084850] hub 1-1:1.0: USB hub found <6>[ 3.088955] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.096766] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.105794] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.112901] hub 1-1:1.0: 3 ports detected <6>[ 3.117242] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.125775] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.132780] hctosys: unable to open rtc device (rtc0) <6>[ 3.139352] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.146757] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.155588] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.163282] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.171942] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.180630] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.187600] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.195433] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.204460] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.211609] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.219323] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.226697] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.234852] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.242338] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 3.258700] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.273678] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.398526] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.407988] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.437986] Sending DHCP requests ., OK <6>[ 6.482146] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 6.490489] IP-Config: Complete: <6>[ 6.494008] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.504756] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 6.512897] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.512906] nameserver0=192.168.201.1 <6>[ 6.531771] Freeing unused kernel memory: 2048K <6>[ 6.548314] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.666441] udevd[113]: starting version 3.2.9 <5>[ 6.672616] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.679644] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.686462] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.700830] udevd[113]: specified user 'tss' unknown <27>[ 6.706270] udevd[113]: specified group 'tss' unknown <30>[ 6.713685] udevd[114]: starting eudev-3.2.9 <4>[ 7.045511] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.054292] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.067596] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.068373] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.075303] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.082182] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.089903] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.103256] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.104280] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.110112] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.119147] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.132740] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.140893] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.148326] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.156922] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.164560] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.173861] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.182609] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.189677] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.214019] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 7.247145] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.250364] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.262581] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.271742] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.273053] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.293202] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.301838] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.302092] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.313906] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.326209] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.333773] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.343127] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.351870] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.358975] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.369145] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.375525] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <4>[ 7.380859] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.384021] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.391170] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.409332] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.419342] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.426808] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.435542] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.443216] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.452538] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.461273] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.468431] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.476907] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.486043] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.493268] panel-simple panel-lvds0: Dropping the link to regulator.0 done Saving random seed: <5>[ 7.822549] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.909685] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11829289/environment . /lava-11829289/environment / # /lava-11829289/bin/lava-test-runner /lava-11829289/0 /lava-11829289/bin/lava-test-runner /lava-11829289/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11829289/0/tests/0_dmesg + cat uuid <8>[ 8.513062] + UUID=11829289_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.556940] <8>[ 8.597808] <8>[ 8.638534] + set +x <8>[ 8.648446] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11829289/environment / # . /lava-11829289/environment/lava-11829289/bin/lava-test-runner /lava-11829289/1 / # /lava-11829289/bin/lava-test-runner /lava-11829289/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11829289/1/tests/1_bootrr + cat uuid + UUID=1182928<8>[ 9.144843] 9_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11829289/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-11829289/1/../bin/lava-test-case <8>[ 10.214821] /lava-11829289/1/../bin/lava-test-case <8>[ 10.253862] /lava-11829289/1/../bin/lava-test-case <8>[ 10.278784] + set +x <8>[ 10.297260] / #