[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11829144/tftp-deploy-pur9ct43/kernel/zImage tftp 0x10000000 11829144/tftp-deploy-pur9ct43/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11829144/tftp-deploy-pur9ct43/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 14 MiB/s done Bytes transferred = 8737280 (855200 hex) => tftp 0x14000000 11829144/tftp-deploy-pur9ct43/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11829144/tftp-deploy-pur9ct43/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11829144/tftp-deploy-pur9ct43/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 14 MiB/s done Bytes transferred = 13341099 (cb91ab hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11829144/tftp-deploy-pur9ct43/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11829144/tftp-deploy-pur9ct43/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11829144/tftp-deploy-pur9ct43/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 8 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x855200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13341035 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.295-cip103-rt33 (KernelCI@build-j75553-arm-gcc-10-multi-v7-defconfig-pns5n) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Oct 20 13:42:18 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939116K/1048576K available (12288K kernel code, 1598K rwdata, 4684K rodata, 2048K init, 394K bss, 43924K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1599 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021381] Console: colour dummy device 80x30 <6>[ 0.023263] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033679] CPU: Testing write buffer coherency: ok <6>[ 0.038814] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044110] pid_max: default: 32768 minimum: 301 <6>[ 0.049116] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.055879] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.064032] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069788] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077484] rcu: Hierarchical SRCU implementation. <6>[ 0.084235] EFI services will not be available. <6>[ 0.086485] smp: Bringing up secondary CPUs ... <6>[ 0.091866] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091872] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.103196] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.103202] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114398] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114404] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124746] smp: Brought up 1 node, 4 CPUs <6>[ 0.128997] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135413] CPU: All CPU(s) started in SVC mode. <6>[ 0.141367] devtmpfs: initialized <6>[ 0.151092] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156556] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166299] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175849] pinctrl core: initialized pinctrl subsystem <6>[ 0.180103] DMI not present or invalid. <6>[ 0.183413] NET: Registered protocol family 16 <6>[ 0.190789] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197463] cpuidle: using governor menu <6>[ 0.199436] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214460] vdd1p1: supplied by regulator-dummy <6>[ 0.216925] vdd3p0: supplied by regulator-dummy <6>[ 0.221666] vdd2p5: supplied by regulator-dummy <6>[ 0.226505] vddarm: supplied by regulator-dummy <6>[ 0.231397] vddpu: supplied by regulator-dummy <6>[ 0.235837] vddsoc: supplied by regulator-dummy <6>[ 0.254526] No ATAGs? <6>[ 0.254659] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262614] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.272087] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278958] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290804] Serial: AMBA PL011 UART driver <6>[ 0.294622] console [pstore-1] enabled <6>[ 0.296473] pstore: Registered ramoops as persistent store backend <6>[ 0.302765] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.331194] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340621] vgaarb: loaded <5>[ 0.341561] SCSI subsystem initialized <6>[ 0.345183] usbcore: registered new interface driver usbfs <6>[ 0.350517] usbcore: registered new interface driver hub <6>[ 0.356107] usbcore: registered new device driver usb <6>[ 0.362613] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366320] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372450] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376845] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382847] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387375] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394477] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.398152] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407581] PTP clock support registered <6>[ 0.411965] EDAC MC: Ver: 3.0.0 <6>[ 0.417873] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.480528] NET: Registered protocol family 2 <6>[ 0.482727] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490294] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.497201] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.504597] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.511333] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.518020] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.524006] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.530770] NET: Registered protocol family 1 <6>[ 0.535777] RPC: Registered named UNIX socket transport module. <6>[ 0.541398] RPC: Registered udp transport module. <6>[ 0.546330] RPC: Registered tcp transport module. <6>[ 0.551301] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.558480] Trying to unpack rootfs image as initramfs... <6>[ 1.672937] Freeing initrd memory: 13032K <4>[ 1.674806] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.682114] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.692087] Initialise system trusted keyrings <6>[ 1.695100] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.707600] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.711654] NFS: Registering the id_resolver key type <5>[ 1.716210] Key type id_resolver registered <5>[ 1.720618] Key type id_legacy registered <6>[ 1.724892] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.731615] Key type asymmetric registered <5>[ 1.733815] Asymmetric key parser 'x509' registered <6>[ 1.739016] bounce: pool size: 64 pages <6>[ 1.743069] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.750713] io scheduler noop registered <6>[ 1.754866] io scheduler deadline registered <6>[ 1.759626] io scheduler cfq registered (default) <6>[ 1.764352] io scheduler mq-deadline registered <6>[ 1.769153] io scheduler kyber registered <6>[ 1.795182] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.799760] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.806850] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.814190] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.834320] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.837711] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.845562] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.851775] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.859623] PU : no governor for states <4>[ 1.859696] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 1.863589] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.873351] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.937356] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.944680] SuperH (H)SCI(F) driver initialized <6>[ 1.947530] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.956330] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.967256] console [ttymxc1] enabled <6>[ 1.967256] console [ttymxc1] enabled <6>[ 1.972256] bootconsole [ec_imx21] disabled <6>[ 1.972256] bootconsole [ec_imx21] disabled <6>[ 1.982326] msm_serial: driver initialized <6>[ 1.988607] STMicroelectronics ASC driver initialized <6>[ 1.995780] STM32 USART driver initialized <4>[ 2.010962] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.019655] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.026647] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.033435] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.042464] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.049632] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.064374] brd: module loaded <6>[ 2.074425] loop: module loaded <6>[ 2.081059] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.089274] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.097549] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.106011] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.116803] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.124087] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.133162] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.143998] scsi host0: ahci-imx <6>[ 2.148095] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.167025] CAN device driver interface <6>[ 2.172399] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.179510] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.188493] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.197558] pps pps0: new PPS source ptp0 <6>[ 2.228630] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.236047] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.242179] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.248433] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.255662] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.267362] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.275098] usbcore: registered new interface driver pegasus <6>[ 2.281090] usbcore: registered new interface driver asix <6>[ 2.286788] usbcore: registered new interface driver ax88179_178a <6>[ 2.293198] usbcore: registered new interface driver cdc_ether <6>[ 2.299361] usbcore: registered new interface driver smsc75xx <6>[ 2.305426] usbcore: registered new interface driver smsc95xx <6>[ 2.311495] usbcore: registered new interface driver net1080 <6>[ 2.317451] usbcore: registered new interface driver cdc_subset <6>[ 2.323688] usbcore: registered new interface driver zaurus <6>[ 2.329616] usbcore: registered new interface driver cdc_ncm <6>[ 2.338565] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.345362] ehci-pci: EHCI PCI platform driver <6>[ 2.350127] ehci-platform: EHCI generic platform driver <6>[ 2.355909] ehci-orion: EHCI orion driver <6>[ 2.360440] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.364900] ehci-st: EHCI STMicroelectronics driver <6>[ 2.370261] ehci-exynos: EHCI EXYNOS driver <6>[ 2.374894] ehci-atmel: EHCI Atmel driver <6>[ 2.379376] tegra-ehci: Tegra EHCI driver <6>[ 2.383865] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.390347] ohci-pci: OHCI PCI platform driver <6>[ 2.395108] ohci-platform: OHCI generic platform driver <6>[ 2.400882] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.405343] ohci-st: OHCI STMicroelectronics driver <6>[ 2.410698] ohci-atmel: OHCI Atmel driver <6>[ 2.415971] usbcore: registered new interface driver usb-storage <6>[ 2.424534] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.436578] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.446728] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.451925] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.479373] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.485072] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.487911] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.491642] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.498001] hub 1-0:1.0: USB hub found <6>[ 2.508753] hub 1-0:1.0: 1 port detected <6>[ 2.519270] i2c /dev entries driver <6>[ 2.537528] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.549011] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.555459] sdhci: Copyright(c) Pierre Ossman <6>[ 2.562388] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.570680] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.577486] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.582952] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.588470] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.628327] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.636345] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.641918] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.681747] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.693247] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.700549] usbcore: registered new interface driver usbhid <6>[ 2.706389] usbhid: USB HID core driver <6>[ 2.716485] NET: Registered protocol family 10 <6>[ 2.722318] Segment Routing with IPv6 <6>[ 2.726332] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.733106] NET: Registered protocol family 17 <6>[ 2.737827] can: controller area network core (rev 20170425 abi 9) <6>[ 2.744370] NET: Registered protocol family 29 <6>[ 2.749108] can: raw protocol (rev 20170425) <6>[ 2.753649] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.759598] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.765767] Key type dns_resolver registered <6>[ 2.771344] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.777062] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.782831] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.789325] ThumbEE CPU extension supported. <5>[ 2.793874] Registering SWP/SWPB emulation handler <5>[ 2.799784] Loading compiled-in X.509 certificates <6>[ 2.806284] pstore: Using compression: deflate <6>[ 2.807272] mmc0: new high speed SDHC card at address 0001 <6>[ 2.819198] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 2.824262] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.831695] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 2.839831] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.840292] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 2.847502] GPT:29296874 != 30965759 <6>[ 2.854976] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 2.857893] usb 1-1: new high-speed USB device number 2 using ci_hdrc <4>[ 2.858780] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.867415] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <4>[ 2.872628] GPT:29296874 != 30965759 <4>[ 2.872631] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.872675] mmcblk0: p1 p2 p3 <6>[ 2.878970] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.907077] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.915017] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.924066] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.931227] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.939850] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.950327] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.957684] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.965952] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.973439] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.981994] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.990676] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.997634] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.005418] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.014443] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.021583] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.029336] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.036697] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.044836] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.052314] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.060772] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.069445] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.076401] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 3.083464] hub 1-1:1.0: USB hub found <4>[ 3.084241] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.087618] hub 1-1:1.0: 3 ports detected <6>[ 3.096517] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.107921] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.116016] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.123413] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.123428] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.138145] hctosys: unable to open rtc device (rtc0) <6>[ 3.138400] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.151015] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.159774] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.168480] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.175445] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.183299] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.192320] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.199457] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.207142] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.214534] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.268058] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.283029] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.398495] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.407957] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.438023] Sending DHCP requests ., OK <6>[ 6.482125] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 6.490428] IP-Config: Complete: <6>[ 6.493927] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.504646] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 6.512762] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.512767] nameserver0=192.168.201.1 <6>[ 6.530534] Freeing unused kernel memory: 2048K <6>[ 6.548175] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.691642] udevd[112]: starting version 3.2.9 <5>[ 6.697335] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.704962] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.711781] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.725515] udevd[112]: specified user 'tss' unknown <27>[ 6.730983] udevd[112]: specified group 'tss' unknown <30>[ 6.738633] udevd[113]: starting eudev-3.2.9 <6>[ 7.054549] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.065998] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.075131] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.076833] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.084350] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.092136] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.098409] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.112937] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.120421] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.121068] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.128748] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.133902] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.142929] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.156440] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.164534] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.171961] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.180628] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.188235] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.197421] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.206158] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.213155] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.252801] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 7.271900] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.281047] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.291039] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.299705] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.307225] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.316296] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.323758] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.330151] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.335598] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <4>[ 7.339719] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.339850] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.341761] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.343731] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.348444] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.352376] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.385233] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.393384] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.402052] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.412015] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.419946] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.428451] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.435885] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.444807] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.452404] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.462643] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.471369] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.478512] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.487428] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.496592] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.503782] panel-simple panel-lvds0: Dropping the link to regulator.0 done Saving random seed: <5>[ 7.860509] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.960301] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11829144/environment . /lava-11829144/environment / # /lava-11829144/bin/lava-test-runner /lava-11829144/0 /lava-11829144/bin/lava-test-runner /lava-11829144/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11829144/0/tests/0_dmesg + cat uuid <8>[ 8.563596] + UUID=11829144_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.607381] <8>[ 8.647456] <8>[ 8.687448] + set +x <8>[ 8.697331] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11829144/environment / # . /lava-11829144/environment/lava-11829144/bin/lava-test-runner /lava-11829144/1 / # /lava-11829144/bin/lava-test-runner /lava-11829144/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11829144/1/tests/1_bootrr + cat uuid <8>[ 9.202074] + UUID=11829144_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11829144/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-11829144/1/../bin/lava-test-case <8>[ 10.271178] /lava-11829144/1/../bin/lava-test-case <8>[ 10.310414] /lava-11829144/1/../bin/lava-test-case <8>[ 10.335393] + set +x <8>[ 10.353990] / #