[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.13 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12403157/tftp-deploy-2oqwpt3f/kernel/zImage tftp 0x10000000 12403157/tftp-deploy-2oqwpt3f/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '12403157/tftp-deploy-2oqwpt3f/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 3.9 MiB/s done Bytes transferred = 8831488 (86c200 hex) => tftp 0x14000000 12403157/tftp-deploy-2oqwpt3f/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12403157/tftp-deploy-2oqwpt3f/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '12403157/tftp-deploy-2oqwpt3f/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 4.2 MiB/s done Bytes transferred = 13346176 (cba580 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12403157/tftp-deploy-2oqwpt3f/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12403157/tftp-deploy-2oqwpt3f/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '12403157/tftp-deploy-2oqwpt3f/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.2 MiB/s done Bytes transferred = 41818 (a35a hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x86c200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13346112 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d359 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.299-cip105-rt34 (KernelCI@build-j60885-arm-gcc-10-multi-v7-defconfig-preempt-rt-n2dlk) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT RT Thu Dec 28 20:09:58 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') <6>[ 0.000000] bootconsole [ec_imx21] enabled <6>[ 0.000000] Memory policy: Data cache writealloc <6>[ 0.000000] efi: Getting EFI parameters from FDT: <6>[ 0.000000] efi: UEFI not found. <3>[ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring <6>[ 0.000000] cma: Reserved 64 MiB at 0x4c000000 <6>[ 0.000000] percpu: Embedded 17 pages/cpu s38944 r8192 d22496 u69632 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 <5>[ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 938552K/1048576K available (12288K kernel code, 1636K rwdata, 4696K rodata, 2048K init, 406K bss, 44488K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1637 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 407 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU priority boosting: priority 1 delay 500 ms. <6>[ 0.000000] No expedited grace period (rcu_normal_after_boot). <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000006] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.000016] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.003029] Console: colour dummy device 80x30 <6>[ 0.273312] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.273321] CPU: Testing write buffer coherency: ok <6>[ 0.273360] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.273366] pid_max: default: 32768 minimum: 301 <6>[ 0.273527] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.273547] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.274708] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.320321] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.328020] rcu: Hierarchical SRCU implementation. <6>[ 0.335205] EFI services will not be available. <6>[ 0.337547] smp: Bringing up secondary CPUs ... <6>[ 0.343338] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.343346] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.344890] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.344895] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.346431] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.346437] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.346574] smp: Brought up 1 node, 4 CPUs <6>[ 0.381753] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.388273] CPU: All CPU(s) started in SVC mode. <6>[ 0.394373] devtmpfs: initialized <6>[ 0.409525] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.415239] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.424725] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.434423] pinctrl core: initialized pinctrl subsystem <6>[ 0.439407] DMI not present or invalid. <6>[ 0.442102] NET: Registered protocol family 16 <6>[ 0.451578] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.459319] cpuidle: using governor menu <6>[ 0.460900] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.480073] vdd1p1: supplied by regulator-dummy <6>[ 0.482768] vdd3p0: supplied by regulator-dummy <6>[ 0.487566] vdd2p5: supplied by regulator-dummy <6>[ 0.492344] vddarm: supplied by regulator-dummy <6>[ 0.497388] vddpu: supplied by regulator-dummy <6>[ 0.501592] vddsoc: supplied by regulator-dummy <6>[ 0.526166] No ATAGs? <6>[ 0.526299] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.534244] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.545112] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.552073] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.566200] Serial: AMBA PL011 UART driver <6>[ 0.570912] console [pstore-1] enabled <6>[ 0.572292] pstore: Registered ramoops as persistent store backend <6>[ 0.578508] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.620197] mxs-dma 110000.dma-apbh: initialized <6>[ 0.632759] vgaarb: loaded <5>[ 0.634193] SCSI subsystem initialized <6>[ 0.637456] usbcore: registered new interface driver usbfs <6>[ 0.642689] usbcore: registered new interface driver hub <6>[ 0.648245] usbcore: registered new device driver usb <6>[ 0.655527] i2c i2c-0: IMX I2C adapter registered <6>[ 0.658464] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.665100] i2c i2c-1: IMX I2C adapter registered <6>[ 0.668988] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.675331] i2c i2c-2: IMX I2C adapter registered <6>[ 0.679517] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.687098] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.690294] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.699716] PTP clock support registered <6>[ 0.704214] EDAC MC: Ver: 3.0.0 <6>[ 0.711237] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.811474] NET: Registered protocol family 2 <6>[ 0.813719] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.821417] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.828262] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.835622] TCP bind hash table entries: 8192 (order: 5, 229376 bytes) <6>[ 0.842684] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.849191] UDP hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.855174] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.862013] NET: Registered protocol family 1 <6>[ 0.867115] RPC: Registered named UNIX socket transport module. <6>[ 0.872498] RPC: Registered udp transport module. <6>[ 0.877451] RPC: Registered tcp transport module. <6>[ 0.882415] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.889762] Trying to unpack rootfs image as initramfs... <6>[ 2.144087] Freeing initrd memory: 13036K <4>[ 2.145982] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.153201] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 2.164229] Initialise system trusted keyrings <6>[ 2.166425] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.184836] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.189244] NFS: Registering the id_resolver key type <5>[ 2.193432] Key type id_resolver registered <5>[ 2.197829] Key type id_legacy registered <6>[ 2.202160] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.209476] Key type asymmetric registered <5>[ 2.211058] Asymmetric key parser 'x509' registered <6>[ 2.216318] bounce: pool size: 64 pages <6>[ 2.220322] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 2.227937] io scheduler noop registered <6>[ 2.232111] io scheduler deadline registered <6>[ 2.237009] io scheduler cfq registered (default) <6>[ 2.241596] io scheduler mq-deadline registered <6>[ 2.246378] io scheduler kyber registered <6>[ 2.281737] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.286317] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.293464] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.300742] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.321606] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.328518] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <4>[ 2.336795] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.342601] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.350402] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.356657] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 2.364489] PU : no governor for states <6>[ 2.368454] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 2.462907] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.471813] SuperH (H)SCI(F) driver initialized <6>[ 2.475099] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 2.483931] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 2.494418] console [ttymxc1] enabled <6>[ 2.494418] console [ttymxc1] enabled <6>[ 2.499404] bootconsole [ec_imx21] disabled <6>[ 2.499404] bootconsole [ec_imx21] disabled <6>[ 2.510000] msm_serial: driver initialized <6>[ 2.515842] STMicroelectronics ASC driver initialized <6>[ 2.523655] STM32 USART driver initialized <4>[ 2.541830] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.550575] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.557601] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.564396] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.573451] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.580629] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.600114] brd: module loaded <6>[ 2.614726] loop: module loaded <6>[ 2.622641] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.630838] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.639121] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.647577] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.658410] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.665675] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.674742] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.685960] scsi host0: ahci-imx <6>[ 2.690249] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.713963] CAN device driver interface <6>[ 2.719670] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.727073] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.736061] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.745524] pps pps0: new PPS source ptp0 <6>[ 2.780222] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.787925] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.794033] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.800306] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.807541] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.821096] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.828830] usbcore: registered new interface driver pegasus <6>[ 2.834835] usbcore: registered new interface driver asix <6>[ 2.840553] usbcore: registered new interface driver ax88179_178a <6>[ 2.846977] usbcore: registered new interface driver cdc_ether <6>[ 2.853171] usbcore: registered new interface driver smsc75xx <6>[ 2.859261] usbcore: registered new interface driver smsc95xx <6>[ 2.865337] usbcore: registered new interface driver net1080 <6>[ 2.871346] usbcore: registered new interface driver cdc_subset <6>[ 2.877582] usbcore: registered new interface driver zaurus <6>[ 2.883527] usbcore: registered new interface driver cdc_ncm <6>[ 2.893469] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.900272] ehci-pci: EHCI PCI platform driver <6>[ 2.905051] ehci-platform: EHCI generic platform driver <6>[ 2.910926] ehci-orion: EHCI orion driver <6>[ 2.915528] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.920087] ehci-st: EHCI STMicroelectronics driver <6>[ 2.925529] ehci-exynos: EHCI EXYNOS driver <6>[ 2.930255] ehci-atmel: EHCI Atmel driver <6>[ 2.934812] tegra-ehci: Tegra EHCI driver <6>[ 2.939397] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.945874] ohci-pci: OHCI PCI platform driver <6>[ 2.950651] ohci-platform: OHCI generic platform driver <6>[ 2.956506] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.961056] ohci-st: OHCI STMicroelectronics driver <6>[ 2.966486] ohci-atmel: OHCI Atmel driver <6>[ 2.972131] usbcore: registered new interface driver usb-storage <6>[ 2.981403] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.994430] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 3.004982] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.010176] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.022841] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.028546] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.035089] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.041296] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.042320] hub 1-0:1.0: USB hub found <6>[ 3.042368] hub 1-0:1.0: 1 port detected <6>[ 3.051670] i2c /dev entries driver <3>[ 3.067045] imx_thermal tempmon: invalid sensor calibration data <3>[ 3.073332] imx_thermal tempmon: failed to init from from fsl,tempmon-data <4>[ 3.080495] imx_thermal: probe of tempmon failed with error -22 <6>[ 3.091396] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.104661] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.111112] sdhci: Copyright(c) Pierre Ossman <6>[ 3.118652] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.127566] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.134494] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 3.139944] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 3.145523] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.185803] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 3.193895] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 3.199563] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 3.240987] mmc0: new high speed SDHC card at address 0001 <6>[ 3.241616] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 3.247870] usbcore: registered new interface driver usbhid <6>[ 3.247874] usbhid: USB HID core driver <6>[ 3.255976] NET: Registered protocol family 10 <6>[ 3.257527] Segment Routing with IPv6 <6>[ 3.257628] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.258466] NET: Registered protocol family 17 <6>[ 3.258488] can: controller area network core (rev 20170425 abi 9) <6>[ 3.258616] NET: Registered protocol family 29 <6>[ 3.258627] can: raw protocol (rev 20170425) <6>[ 3.258636] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.258653] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 3.259226] Key type dns_resolver registered <6>[ 3.260437] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 3.260536] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 3.260660] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 3.262011] ThumbEE CPU extension supported. <5>[ 3.262030] Registering SWP/SWPB emulation handler <5>[ 3.262910] Loading compiled-in X.509 certificates <6>[ 3.265013] pstore: Using compression: deflate <6>[ 3.296561] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.296686] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.298919] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.299031] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.301441] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.301533] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.301659] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.303583] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.303697] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.303821] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.305502] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.305609] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.307456] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.307561] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.309741] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.309827] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.309951] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.311949] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.312061] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.312188] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.316193] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.317485] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.317594] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.319576] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.319686] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 3.321477] hctosys: unable to open rtc device (rtc0) <4>[ 3.322051] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.322146] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.322275] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.324762] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.324935] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.325112] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.331310] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 3.432057] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 3.432272] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 3.539101] hub 1-1:1.0: USB hub found <6>[ 3.539272] hub 1-1:1.0: 3 ports detected <6>[ 3.622538] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.629966] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.632815] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 3.645547] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.653572] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.664022] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <4>[ 3.664585] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.664591] GPT:29296874 != 30965759 <4>[ 3.664595] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.664600] GPT:29296874 != 30965759 <4>[ 3.664604] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.664655] mmcblk0: p1 p2 p3 <6>[ 3.703079] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.710099] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.718786] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.727852] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.735038] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.743459] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.750885] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.759829] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.767345] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.776719] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.785430] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.792439] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 5.512210] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 5.531782] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.561500] Sending DHCP requests ., OK <6>[ 5.605564] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.13 <6>[ 5.613859] IP-Config: Complete: <6>[ 5.617384] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.201.13, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.628173] host=imx6q-sabrelite-lava-cbg-2, domain=lava-rack, nis-domain=(none) <6>[ 5.636281] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.636286] nameserver0=192.168.201.1 <6>[ 5.655494] Freeing unused kernel memory: 2048K <6>[ 5.660677] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.834805] udevd[140]: starting version 3.2.9 <5>[ 5.840774] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.847818] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.854663] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.870897] udevd[140]: specified user 'tss' unknown <27>[ 5.876402] udevd[140]: specified group 'tss' unknown <30>[ 5.884741] udevd[141]: starting eudev-3.2.9 <4>[ 6.961589] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.977944] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.985221] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.996062] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.003507] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.016670] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.024220] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.025116] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.039986] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.048310] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.057545] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.064605] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.064812] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.064829] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.087012] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.098907] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 7.110762] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.120886] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.128367] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.133417] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.133432] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.154279] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.163369] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.170796] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.183636] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.186616] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.188252] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.202532] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.202949] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.203078] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.212746] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.213533] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.213947] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.260766] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.268206] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.291877] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.299811] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.318265] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.327328] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.334367] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.352257] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.365563] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.372774] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.814442] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.821927] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.834031] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.841589] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.850069] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.857099] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.864857] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 7.867337] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.867906] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.868201] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.875424] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.876236] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.876451] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.919792] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.964601] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.972057] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.984545] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.992104] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 8.005692] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 8.014559] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 8.021629] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 8.033024] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 8.045980] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 8.053239] panel-simple panel-lvds0: Dropping the link to regulator.0 done Saving random seed: <5>[ 8.425249] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.559958] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12403157/environment . /lava-12403157/environment / # /lava-12403157/bin/lava-test-runner /lava-12403157/0 /lava-12403157/bin/lava-test-runner /lava-12403157/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12403157/0/tests/0_dmesg + cat uuid + UUID=12403157_1.5.2.4.1<8>[ 9.216050] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.279596] <8>[ 9.345520] <8>[ 9.404615] + set +x <8>[ 9.414821] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12403157/environment / # . /lava-12403157/environment/lava-12403157/bin/lava-test-runner /lava-12403157/1 / # /lava-12403157/bin/lava-test-runner /lava-12403157/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12403157/1/tests/1_bootrr + cat uuid + UUID=12403157_1.5.2.4.5 + set<8>[ 9.950244] +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12403157/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-12403157/1/../bin/lava-test-case <8>[ 11.056236] /lava-12403157/1/../bin/lava-test-case <8>[ 11.116648] /lava-12403157/1/../bin/lava-test-case <8>[ 11.149310] + set<8>[ 11.178012] +x / #