Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1066360/tftp-deploy-n5tkeuzq/kernel/zImage tftp 0x82000000 1066360/tftp-deploy-n5tkeuzq/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1066360/tftp-deploy-n5tkeuzq/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.1 MiB/s done Bytes transferred = 4513448 (44dea8 hex) => tftp 0x83000000 1066360/tftp-deploy-n5tkeuzq/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1066360/tftp-deploy-n5tkeuzq/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1066360/tftp-deploy-n5tkeuzq/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# #################### 5.2 MiB/s done Bytes transferred = 12690248 (c1a348 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1066360/tftp-deploy-n5tkeuzq/dtb/am335x-boneblack.dtb tftp 0x88000000 1066360/tftp-deploy-n5tkeuzq/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1066360/tftp-deploy-n5tkeuzq/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *### 4.2 MiB/s done Bytes transferred = 34893 (884d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-12-28 20:29:00 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12690184 Bytes = 12.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800b84c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.299-cip105-rt34 (KernelCI@build-j60930-arm-gcc-10-omap2plus-defconfig-fmrtk) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Thu Dec 28 19:51:55 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 17 pages/cpu s38824 r8192 d22616 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 466584K/522240K available (9216K kernel code, 795K rwdata, 2608K rodata, 1024K init, 7477K bss, 39272K reserved, 16384K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 796 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7478 kB) <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz <6>[ 0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008362] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018161] OMAP clocksource: timer1 at 24000000 Hz <2>[ 0.023933] timer_probe: no matching timers found <6>[ 0.030373] Console: colour dummy device 80x30 <3>[ 0.035271] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042318] This ensures that you still see kernel messages. Please <3>[ 0.049068] update your kernel commandline. <4>[ 0.053646] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.061912] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.066399] ... MAX_LOCK_DEPTH: 48 <4>[ 0.070999] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.075753] ... CLASSHASH_SIZE: 4096 <4>[ 0.080533] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.085376] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.090245] ... CHAINHASH_SIZE: 32768 <4>[ 0.095089] memory used by lock dependency info: 4655 kB <4>[ 0.100941] per task-struct memory footprint: 1536 bytes <6>[ 0.106813] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.145358] CPU: Testing write buffer coherency: ok <6>[ 0.150871] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.156344] pid_max: default: 32768 minimum: 301 <6>[ 0.161793] Security Framework initialized <6>[ 0.166399] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.173538] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.185895] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.194029] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.201798] rcu: Hierarchical SRCU implementation. <6>[ 0.209446] smp: Bringing up secondary CPUs ... <6>[ 0.214392] smp: Brought up 1 node, 1 CPU <6>[ 0.218866] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.225589] CPU: All CPU(s) started in SVC mode. <6>[ 0.234598] devtmpfs: initialized <6>[ 0.263664] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.272704] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.283227] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.291497] pinctrl core: initialized pinctrl subsystem <6>[ 0.302818] NET: Registered protocol family 16 <6>[ 0.314364] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.383254] l4_wkup_cm:clk:0010:0: failed to disable <6>[ 0.430818] audit: initializing netlink subsys (disabled) <6>[ 0.439951] cpuidle: using governor menu <5>[ 0.457912] audit: type=2000 audit(0.400:1): state=initialized audit_enabled=0 res=1 <6>[ 0.467684] OMAP GPIO hardware version 0.1 <6>[ 0.497853] No ATAGs? <6>[ 0.497867] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.544048] edma 49000000.edma: TI EDMA DMA engine driver <6>[ 0.556747] vgaarb: loaded <5>[ 0.561001] SCSI subsystem initialized <6>[ 0.567148] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.572680] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.582455] PTP clock support registered <6>[ 0.590995] clocksource: Switched to clocksource timer1 <5>[ 0.749535] VFS: Disk quotas dquot_6.6.0 <6>[ 0.754221] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 0.788249] NET: Registered protocol family 2 <6>[ 0.793863] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.802850] tcp_listen_portaddr_hash hash table entries: 256 (order: 1, 10240 bytes) <6>[ 0.811353] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.818955] TCP bind hash table entries: 4096 (order: 5, 147456 bytes) <6>[ 0.826552] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.833854] UDP hash table entries: 256 (order: 2, 20480 bytes) <6>[ 0.840317] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) <6>[ 0.847740] NET: Registered protocol family 1 <6>[ 0.855565] RPC: Registered named UNIX socket transport module. <6>[ 0.862161] RPC: Registered udp transport module. <6>[ 0.867279] RPC: Registered tcp transport module. <6>[ 0.872486] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.881735] Trying to unpack rootfs image as initramfs... <6>[ 2.074725] Freeing initrd memory: 12396K <6>[ 2.081464] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 2.095869] Initialise system trusted keyrings <6>[ 2.102353] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 2.113269] NFS: Registering the id_resolver key type <5>[ 2.118961] Key type id_resolver registered <5>[ 2.123735] Key type id_legacy registered <6>[ 2.128368] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 2.144316] Key type asymmetric registered <5>[ 2.149036] Asymmetric key parser 'x509' registered <6>[ 2.154773] io scheduler noop registered <6>[ 2.159096] io scheduler deadline registered <6>[ 2.164053] io scheduler cfq registered (default) <6>[ 2.169178] io scheduler mq-deadline registered <6>[ 2.174196] io scheduler kyber registered <6>[ 2.181578] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 2.196527] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 2.216378] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a 8250 <6>[ 2.226377] console [ttyS0] enabled <6>[ 2.226377] console [ttyS0] enabled <6>[ 2.234190] bootconsole [omap8250] disabled <6>[ 2.234190] bootconsole [omap8250] disabled <6>[ 2.275596] brd: module loaded <6>[ 2.301789] loop: module loaded <3>[ 2.307904] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 2.390979] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 2.399001] davinci_mdio 4a101000.mdio: detected phy mask fffffffe <6>[ 2.441453] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 2.452425] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 2.460088] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 2.466946] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 2.472633] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 2.483624] i2c /dev entries driver <6>[ 2.491456] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.497960] sdhci: Copyright(c) Pierre Ossman <6>[ 2.504106] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 2.513715] omap_hsmmc 48060000.mmc: Got CD GPIO <6>[ 2.520416] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 <6>[ 2.557655] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1 <6>[ 2.589678] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.596421] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.605924] oprofile: using arm/armv7 <6>[ 2.610988] Initializing XFRM netlink socket <6>[ 2.616251] NET: Registered protocol family 10 <6>[ 2.625967] Segment Routing with IPv6 <6>[ 2.630110] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.638544] NET: Registered protocol family 17 <6>[ 2.643531] NET: Registered protocol family 15 <5>[ 2.648685] Key type dns_resolver registered <6>[ 2.653493] ThumbEE CPU extension supported. <5>[ 2.658090] Registering SWP/SWPB emulation handler <3>[ 2.663309] omap_voltage_late_init: Voltage driver support not added <3>[ 2.669978] sr_dev_init: Unknown instance smartreflex0 <6>[ 2.675929] SmartReflex Class3 initialized <5>[ 2.683944] Loading compiled-in X.509 certificates <6>[ 2.783747] mmc1: new high speed MMC card at address 0001 <6>[ 2.794724] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 2.801446] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 2.809300] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 2.819190] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (248:0) <6>[ 2.835376] mmcblk1: p1 <6>[ 2.859796] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 2.866657] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 2.876886] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 2.884645] hctosys: unable to open rtc device (rtc0) <4>[ 2.890019] sr_init: No PMIC hook to init smartreflex <6>[ 2.914365] net eth0: initializing cpsw version 1.12 (0) <6>[ 3.022266] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 3.045740] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.191990] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 6.201336] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.230920] Sending DHCP requests ., OK <6>[ 6.275586] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 6.283766] IP-Config: Complete: <6>[ 6.287292] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 6.297868] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 6.304949] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 6.304956] nameserver0=192.168.11.1 <6>[ 6.322849] Freeing unused kernel memory: 1024K <6>[ 6.342235] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.787970] udevd[87]: starting version 3.2.9 <5>[ 6.795829] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.804767] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.812263] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.833754] udevd[87]: specified user 'tss' unknown <27>[ 6.839379] udevd[87]: specified group 'tss' unknown <30>[ 6.856082] udevd[88]: starting eudev-3.2.9 <6>[ 7.576378] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 7.621714] cpu cpu0: Dropping the link to regulator.3 <6>[ 7.670141] cpu cpu0: Linked as a consumer to regulator.3 <6>[ 7.694036] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 7.718011] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 7.831507] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 7.874427] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 7.889629] input: tps65217_pwrbutton as /devices/platform/ocp/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 7.932007] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 8.231629] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 8.239656] random: crng init done <6>[ 8.287887] tda998x 0-0070: found TDA19988 <6>[ 8.352675] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops [tda998x]) <6>[ 8.360141] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 8.367301] [drm] No driver support for vblank timestamp query. <6>[ 8.481129] [drm] Cannot find any crtc or sizes <6>[ 8.568374] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <3>[ 8.798913] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle <6>[ 8.865064] remoteproc remoteproc0: wkup_m3 is available <6>[ 8.877834] remoteproc remoteproc0: powering up wkup_m3 <4>[ 8.931663] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 8.942404] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 8.948648] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <4>[ 9.032066] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator <6>[ 9.042770] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 <6>[ 9.094577] usbcore: registered new interface driver usbfs <6>[ 9.101453] usbcore: registered new interface driver hub <6>[ 9.107262] usbcore: registered new device driver usb <4>[ 9.220654] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator <6>[ 9.231528] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 <6>[ 9.384589] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.391863] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <3>[ 9.402447] pm33xx pm33xx: PM: Unable to allocate memory from ocmcram <4>[ 9.409273] pm33xx: probe of pm33xx failed with error -12 <6>[ 9.496324] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 <6>[ 9.505395] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.513053] usb usb1: Product: MUSB HDRC host driver <6>[ 9.518318] usb usb1: Manufacturer: Linux 4.19.299-cip105-rt34 musb-hcd <6>[ 9.525299] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.554898] [drm] Cannot find any crtc or sizes <6>[ 9.676190] hub 1-0:1.0: USB hub found <6>[ 9.703299] hub 1-0:1.0: 1 port detected <6>[ 9.883375] asoc-simple-card sound: i2s-hifi <-> 48038000.mcasp mapping ok done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1066360/environment . /lava-1066360/environment / # /lava-1066360/bin/lava-test-runner /lava-1066360/0 /lava-1066360/bin/lava-test-runner /lava-1066360/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1066360/0/tests/0_dmesg + cat uuid + UUID=1066360_1.5.2.4.1 <8>[ 11.273410] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh kern :crit : timer_probe: no matching timers found <8>[ 11.388449] <8>[ 11.492713] <8>[ 11.594986] + set +x<8>[ 11.607703] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1066360/environment / # . /lava-1066360/environment/lava-1066360/bin/lava-test-runner /lava-1066360/1 / # /lava-1066360/bin/lava-test-runner /lava-1066360/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1066360/1/tests/1_bootrr + cat uuid + UUID=1066360_1.5.2.4.5 <8>[ 12.213922] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1066360/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-1066360/1/../bin/lava-test-case <8>[ 12.350386] /lava-1066360/1/../bin/lava-test-case <8>[ 12.450023] /lava-1066360/1/../bin/lava-test-case <8>[ 12.504289] /lava-1066360/1/../bin/lava-test-case <8>[ 12.615399] /lava-1066360/1/../bin/lava-test-case <8>[ 12.705752] /lava-1066360/1/../bin/lava-test-case <8>[ 12.776078] /lava-1066360/1/../bin/lava-test-case <8>[ 12.865146] /lava-1066360/1/../bin/lava-test-case <8>[ 12.953753] /lava-1066360/1/../bin/lava-test-case <8>[ 13.024099] /lava-1066360/1/../bin/lava-test-case <8>[ 13.112123] /lava-1066360/1/../bin/lava-test-case <8>[ 13.183583] /lava-1066360/1/../bin/lava-test-case <8>[ 13.304692] /lava-1066360/1/../bin/lava-test-case <8>[ 13.373658] /lava-1066360/1/../bin/lava-test-case <8>[ 13.427362] /lava-1066360/1/../bin/lava-test-case <8>[ 13.498984] /lava-1066360/1/../bin/lava-test-case <8>[ 13.587519] /lava-1066360/1/../bin/lava-test-case <8>[ 13.658906] /lava-1066360/1/../bin/lava-test-case <8>[ 14.782545] /lava-1066360/1/../bin/lava-test-case <8>[ 15.910108] /lava-1066360/1/../bin/lava-test-case <8>[ 15.980178] /lava-1066360/1/../bin/lava-test-case <8>[ 16.068992] /lava-1066360/1/../bin/lava-test-case <8>[ 16.157996] /lava-1066360/1/../bin/lava-test-case <8>[ 16.228998] /lava-1066360/1/../bin/lava-test-case <8>[ 16.318002] /lava-1066360/1/../bin/lava-test-case <8>[ 16.388179] /lava-1066360/1/../bin/lava-test-case <8>[ 16.477318] /lava-1066360/1/../bin/lava-test-case <8>[ 17.582545] /lava-1066360/1/../bin/lava-test-case <8>[ 18.693620] /lava-1066360/1/../bin/lava-test-case <8>[ 19.800114] /lava-1066360/1/../bin/lava-test-case <8>[ 20.911786] /lava-1066360/1/../bin/lava-test-case <8>[ 20.983222] /lava-1066360/1/../bin/lava-test-case <8>[ 21.072015] /lava-1066360/1/../bin/lava-test-case <8>[ 22.174254] /lava-1066360/1/../bin/lava-test-case <8>[ 23.282504] /lava-1066360/1/../bin/lava-test-case <8>[ 23.353501] /lava-1066360/1/../bin/lava-test-case <8>[ 23.443245] /lava-1066360/1/../bin/lava-test-case <8>[ 24.551919] /lava-1066360/1/../bin/lava-test-case <8>[ 25.661690] /lava-1066360/1/../bin/lava-test-case <8>[ 25.732071] /lava-1066360/1/../bin/lava-test-case <8>[ 25.822255] /lava-1066360/1/../bin/lava-test-case <8>[ 25.892211] /lava-1066360/1/../bin/lava-test-case <8>[ 25.982429] /lava-1066360/1/../bin/lava-test-case <8>[ 26.054037] /lava-1066360/1/../bin/lava-test-case <8>[ 26.143816] /lava-1066360/1/../bin/lava-test-case <8>[ 26.213744] /lava-1066360/1/../bin/lava-test-case <8>[ 26.302249] /lava-1066360/1/../bin/lava-test-case <8>[ 26.372271] /lava-1066360/1/../bin/lava-test-case <8>[ 26.461026] /lava-1066360/1/../bin/lava-test-case <8>[ 26.530551] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-1066360/1/../bin/lava-test-case <8>[ 26.603859] /lava-1066360/1/../bin/lava-test-case <8>[ 26.692601] /lava-1066360/1/../bin/lava-test-case <8>[ 26.775894] + set +x <8>[ 26.801722] / #