Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.2 (5 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1101576/tftp-deploy-3rt318da/kernel/zImage tftp 0x82000000 1101576/tftp-deploy-3rt318da/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1101576/tftp-deploy-3rt318da/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.2 MiB/s done Bytes transferred = 8741376 (856200 hex) => tftp 0x83000000 1101576/tftp-deploy-3rt318da/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1101576/tftp-deploy-3rt318da/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1101576/tftp-deploy-3rt318da/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 5.2 MiB/s done Bytes transferred = 13345524 (cba2f4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1101576/tftp-deploy-3rt318da/dtb/am335x-boneblack.dtb tftp 0x88000000 1101576/tftp-deploy-3rt318da/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1101576/tftp-deploy-3rt318da/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *### 4.2 MiB/s done Bytes transferred = 34893 (884d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-03-02 5:24:59 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13345460 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800b84c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.306-cip107-rt35 (KernelCI@build-j127807-arm-gcc-10-multi-v7-defconfig-vd7fl) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Sat Mar 2 02:11:24 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omapserial0 at MMIO 0x44e09000 (options '') [ 0.000000] bootconsole [omapserial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 417356K/522240K available (12288K kernel code, 1598K rwdata, 4688K rodata, 2048K init, 394K bss, 39348K reserved, 65536K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1599 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz <6>[ 0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008240] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.017953] OMAP clocksource: timer1 at 24000000 Hz <2>[ 0.026801] timer_probe: no matching timers found <6>[ 0.032150] Console: colour dummy device 80x30 <6>[ 0.036942] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.075869] CPU: Testing write buffer coherency: ok <6>[ 0.081152] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.086578] pid_max: default: 32768 minimum: 301 <6>[ 0.091725] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.098694] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.107212] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.113440] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.121768] rcu: Hierarchical SRCU implementation. <6>[ 0.129732] EFI services will not be available. <6>[ 0.134769] smp: Bringing up secondary CPUs ... <6>[ 0.139634] smp: Brought up 1 node, 1 CPU <6>[ 0.143981] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.150689] CPU: All CPU(s) started in SVC mode. <6>[ 0.157090] devtmpfs: initialized <6>[ 0.167883] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.176522] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.186860] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.197230] pinctrl core: initialized pinctrl subsystem <6>[ 0.204768] DMI not present or invalid. <6>[ 0.209690] NET: Registered protocol family 16 <6>[ 0.216826] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.249765] l4_wkup_cm:clk:0010:0: failed to disable <6>[ 0.296798] cpuidle: using governor menu <6>[ 0.308162] OMAP GPIO hardware version 0.1 <6>[ 0.324592] No ATAGs? <6>[ 0.324603] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.338769] Serial: AMBA PL011 UART driver <6>[ 0.361492] edma 49000000.edma: TI EDMA DMA engine driver <6>[ 0.370945] vgaarb: loaded <5>[ 0.374742] SCSI subsystem initialized <6>[ 0.379457] usbcore: registered new interface driver usbfs <6>[ 0.385319] usbcore: registered new interface driver hub <6>[ 0.391073] usbcore: registered new device driver usb <6>[ 0.397945] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.403287] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.412904] PTP clock support registered <6>[ 0.417330] EDAC MC: Ver: 3.0.0 <6>[ 0.423820] clocksource: Switched to clocksource timer1 <6>[ 0.490644] NET: Registered protocol family 2 <6>[ 0.495685] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.503195] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.511327] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.518804] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.525682] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.532506] UDP hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.538720] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.545527] NET: Registered protocol family 1 <6>[ 0.550935] RPC: Registered named UNIX socket transport module. <6>[ 0.557262] RPC: Registered udp transport module. <6>[ 0.562290] RPC: Registered tcp transport module. <6>[ 0.567398] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.574922] Trying to unpack rootfs image as initramfs... <6>[ 1.458450] Freeing initrd memory: 13036K <6>[ 1.463577] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 1.474712] Initialise system trusted keyrings <6>[ 1.479941] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 1.493311] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.500669] NFS: Registering the id_resolver key type <5>[ 1.506151] Key type id_resolver registered <5>[ 1.510628] Key type id_legacy registered <6>[ 1.515063] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.521888] Key type asymmetric registered <5>[ 1.526355] Asymmetric key parser 'x509' registered <6>[ 1.531607] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.539429] io scheduler noop registered <6>[ 1.543687] io scheduler deadline registered <6>[ 1.548620] io scheduler cfq registered (default) <6>[ 1.553635] io scheduler mq-deadline registered <6>[ 1.558573] io scheduler kyber registered <6>[ 1.568866] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 1.640495] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.650625] SuperH (H)SCI(F) driver initialized <6>[ 1.656475] msm_serial: driver initialized <6>[ 1.661156] omap_uart 44e09000.serial: no wakeirq for uart0 <6>[ 1.667208] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a OMAP UART0 <6>[ 1.676973] console [ttyO0] enabled <6>[ 1.676973] console [ttyO0] enabled <6>[ 1.684676] bootconsole [omapserial0] disabled <6>[ 1.684676] bootconsole [omapserial0] disabled <6>[ 1.695013] STMicroelectronics ASC driver initialized <6>[ 1.702056] STM32 USART driver initialized <6>[ 1.708289] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 1.720996] random: crng init done <6>[ 1.734339] brd: module loaded <6>[ 1.743607] loop: module loaded <6>[ 1.757156] CAN device driver interface <6>[ 1.762406] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.769695] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.776126] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.782672] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.790258] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.873827] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 1.882138] davinci_mdio 4a101000.mdio: detected phy mask fffffffe <6>[ 1.910444] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 1.922824] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 1.930351] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 1.937340] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 1.944908] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.953019] usbcore: registered new interface driver pegasus <6>[ 1.959354] usbcore: registered new interface driver asix <6>[ 1.965339] usbcore: registered new interface driver ax88179_178a <6>[ 1.972018] usbcore: registered new interface driver cdc_ether <6>[ 1.978480] usbcore: registered new interface driver smsc75xx <6>[ 1.984833] usbcore: registered new interface driver smsc95xx <6>[ 1.991148] usbcore: registered new interface driver net1080 <6>[ 1.997459] usbcore: registered new interface driver cdc_subset <6>[ 2.003985] usbcore: registered new interface driver zaurus <6>[ 2.010142] usbcore: registered new interface driver cdc_ncm <6>[ 2.018589] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.025780] ehci-pci: EHCI PCI platform driver <6>[ 2.030754] ehci-platform: EHCI generic platform driver <6>[ 2.036761] ehci-orion: EHCI orion driver <6>[ 2.041397] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.046058] ehci-st: EHCI STMicroelectronics driver <6>[ 2.051572] ehci-exynos: EHCI EXYNOS driver <6>[ 2.056416] ehci-atmel: EHCI Atmel driver <6>[ 2.061020] tegra-ehci: Tegra EHCI driver <6>[ 2.065677] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.072464] ohci-pci: OHCI PCI platform driver <6>[ 2.077486] ohci-platform: OHCI generic platform driver <6>[ 2.083430] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.088110] ohci-st: OHCI STMicroelectronics driver <6>[ 2.093636] ohci-atmel: OHCI Atmel driver <6>[ 2.098919] usbcore: registered new interface driver usb-storage <6>[ 2.110524] i2c /dev entries driver <6>[ 2.127134] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.133977] sdhci: Copyright(c) Pierre Ossman <6>[ 2.140014] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 2.149475] omap_hsmmc 48060000.mmc: Got CD GPIO <6>[ 2.155102] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 <6>[ 2.187765] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1 <6>[ 2.221930] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.230029] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.239852] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.248254] usbcore: registered new interface driver usbhid <6>[ 2.254444] usbhid: USB HID core driver <6>[ 2.263474] NET: Registered protocol family 10 <6>[ 2.270153] Segment Routing with IPv6 <6>[ 2.274441] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.281600] NET: Registered protocol family 17 <6>[ 2.286601] can: controller area network core (rev 20170425 abi 9) <6>[ 2.293429] NET: Registered protocol family 29 <6>[ 2.298393] can: raw protocol (rev 20170425) <6>[ 2.303137] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.309387] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.316093] Key type dns_resolver registered <6>[ 2.320979] ThumbEE CPU extension supported. <5>[ 2.325811] Registering SWP/SWPB emulation handler <3>[ 2.331114] omap_voltage_late_init: Voltage driver support not added <5>[ 2.340102] Loading compiled-in X.509 certificates <6>[ 2.401124] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 2.408011] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 2.415952] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 2.423366] mmc1: new high speed MMC card at address 0001 <6>[ 2.431380] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 2.437013] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 2.444032] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 2.450756] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 2.460311] mmcblk1: p1 <6>[ 2.555939] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 2.563015] hctosys: unable to open rtc device (rtc0) <6>[ 2.582496] net eth0: initializing cpsw version 1.12 (0) <6>[ 2.684892] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 2.704006] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.794713] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 5.823837] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.853810] Sending DHCP requests ., OK <6>[ 5.898118] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.2 <6>[ 5.906540] IP-Config: Complete: <6>[ 5.910197] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.2, mask=255.255.255.0, gw=192.168.11.1 <6>[ 5.921152] host=192.168.11.2, domain=usen.ad.jp, nis-domain=(none) <6>[ 5.928460] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 5.928464] nameserver0=192.168.11.1 <6>[ 5.944213] Freeing unused kernel memory: 2048K <6>[ 5.954478] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.144089] udevd[85]: starting version 3.2.9 <27>[ 6.159878] udevd[85]: specified user 'tss' unknown <27>[ 6.165755] udevd[85]: specified group 'tss' unknown <30>[ 6.176244] udevd[86]: starting eudev-3.2.9 <4>[ 8.596951] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator <6>[ 8.607780] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 <4>[ 8.675006] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator <6>[ 8.685823] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 <6>[ 8.715891] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 8.721773] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.806832] hub 1-0:1.0: USB hub found <6>[ 8.816678] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1101576/environment . /lava-1101576/environment / # /lava-1101576/bin/lava-test-runner /lava-1101576/0 /lava-1101576/bin/lava-test-runner /lava-1101576/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1101576/0/tests/0_dmesg + cat uuid + UUID=1101576_1.5.2.4.1 + set +x <8>[ 9.552011] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh kern :crit : timer_probe: no matching timers found <8>[ 9.608110] <8>[ 9.657700] <8>[ 9.707326] + set +x <8>[ 9.718278] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1101576/environment / # . /lava-1101576/environment/lava-1101576/bin/lava-test-runner /lava-1101576/1 / # /lava-1101576/bin/lava-test-runner /lava-1101576/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1101576/1/tests/1_bootrr + cat uuid + UUID=1101576_1.5.2.4.5 + set +x <8>[ 10.213129] + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1101576/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound /lava-1101576/1/../bin/lava-test-case <8>[ 11.285314] /lava-1101576/1/../bin/lava-test-case <8>[ 11.332620] /lava-1101576/1/../bin/lava-test-case <8>[ 11.362071] /lava-1101576/1/../bin/lava-test-case <8>[ 12.420504] /lava-1101576/1/../bin/lava-test-case <8>[ 13.463345] /lava-1101576/1/../bin/lava-test-case <8>[ 13.499955] /lava-1101576/1/../bin/lava-test-case <8>[ 13.544634] /lava-1101576/1/../bin/lava-test-case <8>[ 13.587911] /lava-1101576/1/../bin/lava-test-case <8>[ 13.623544] /lava-1101576/1/../bin/lava-test-case <8>[ 13.667733] /lava-1101576/1/../bin/lava-test-case <8>[ 14.708583] /lava-1101576/1/../bin/lava-test-case <8>[ 15.751085] /lava-1101576/1/../bin/lava-test-case <8>[ 15.780211] /lava-1101576/1/../bin/lava-test-case <8>[ 15.808980] /lava-1101576/1/../bin/lava-test-case <8>[ 15.845194] /lava-1101576/1/../bin/lava-test-case <8>[ 15.888934] /lava-1101576/1/../bin/lava-test-case <8>[ 15.925892] /lava-1101576/1/../bin/lava-test-case <8>[ 16.976039] /lava-1101576/1/../bin/lava-test-case <8>[ 18.024899] /lava-1101576/1/../bin/lava-test-case <8>[ 18.060708] /lava-1101576/1/../bin/lava-test-case <8>[ 18.105363] /lava-1101576/1/../bin/lava-test-case <8>[ 18.149932] /lava-1101576/1/../bin/lava-test-case <8>[ 18.186417] /lava-1101576/1/../bin/lava-test-case <8>[ 18.231151] /lava-1101576/1/../bin/lava-test-case <8>[ 18.267720] /lava-1101576/1/../bin/lava-test-case <8>[ 18.312264] /lava-1101576/1/../bin/lava-test-case <8>[ 19.353440] /lava-1101576/1/../bin/lava-test-case <8>[ 20.396580] /lava-1101576/1/../bin/lava-test-case <8>[ 21.438832] /lava-1101576/1/../bin/lava-test-case <8>[ 22.481876] /lava-1101576/1/../bin/lava-test-case <8>[ 22.518793] /lava-1101576/1/../bin/lava-test-case <8>[ 22.563012] /lava-1101576/1/../bin/lava-test-case <8>[ 23.604389] /lava-1101576/1/../bin/lava-test-case <8>[ 24.646613] /lava-1101576/1/../bin/lava-test-case <8>[ 24.682446] /lava-1101576/1/../bin/lava-test-case <8>[ 24.727338] /lava-1101576/1/../bin/lava-test-case <8>[ 25.768201] /lava-1101576/1/../bin/lava-test-case <8>[ 26.810905] /lava-1101576/1/../bin/lava-test-case <8>[ 27.852505] /lava-1101576/1/../bin/lava-test-case <8>[ 28.895061] /lava-1101576/1/../bin/lava-test-case <8>[ 29.936230] /lava-1101576/1/../bin/lava-test-case <8>[ 30.978510] /lava-1101576/1/../bin/lava-test-case <8>[ 32.020552] /lava-1101576/1/../bin/lava-test-case <8>[ 33.062895] /lava-1101576/1/../bin/lava-test-case <8>[ 34.104610] /lava-1101576/1/../bin/lava-test-case <8>[ 35.146842] /lava-1101576/1/../bin/lava-test-case <8>[ 36.188545] /lava-1101576/1/../bin/lava-test-case <8>[ 37.230914] /lava-1101576/1/../bin/lava-test-case <8>[ 38.272862] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-1101576/1/../bin/lava-test-case <8>[ 38.311269] /lava-1101576/1/../bin/lava-test-case <8>[ 39.361704] /lava-1101576/1/../bin/lava-test-case <8>[ 40.402692] + set +x <8>[ 40.418242] / #