[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no => setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff => dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (4 ms) => setenv serverip 192.168.201.1 => tftp 0x10000000 14808755/tftp-deploy-itxnu583/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '14808755/tftp-deploy-itxnu583/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 5.8 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 14808755/tftp-deploy-itxnu583/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '14808755/tftp-deploy-itxnu583/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## 5.8 MiB/s done Bytes transferred = 13312473 (cb21d9 hex) => setenv initrd_size ${filesize} => tftp 0x13f00000 14808755/tftp-deploy-itxnu583/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '14808755/tftp-deploy-itxnu583/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4 MiB/s done Bytes transferred = 41822 (a35e hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13312409 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d35d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.317-cip111-rt37 (KernelCI@build-j264987-arm-gcc-12-defconfig-mvmxn) (gcc version 12.2.0 (Debian 12.2.0-14)) #1 SMP Fri Jul 12 18:04:13 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939144K/1048576K available (12288K kernel code, 1598K rwdata, 4688K rodata, 2048K init, 394K bss, 43896K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1599 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021528] Console: colour dummy device 80x30 <6>[ 0.023411] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033826] CPU: Testing write buffer coherency: ok <6>[ 0.038960] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044256] pid_max: default: 32768 minimum: 301 <6>[ 0.049264] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.056025] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.064188] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069927] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077644] rcu: Hierarchical SRCU implementation. <6>[ 0.084439] EFI services will not be available. <6>[ 0.086690] smp: Bringing up secondary CPUs ... <6>[ 0.092062] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.092069] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.103402] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.103407] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114607] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114613] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124951] smp: Brought up 1 node, 4 CPUs <6>[ 0.129199] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135617] CPU: All CPU(s) started in SVC mode. <6>[ 0.141575] devtmpfs: initialized <6>[ 0.151014] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156471] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166222] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175669] pinctrl core: initialized pinctrl subsystem <6>[ 0.179967] DMI not present or invalid. <6>[ 0.183233] NET: Registered protocol family 16 <6>[ 0.190612] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197299] cpuidle: using governor menu <6>[ 0.199264] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214116] vdd1p1: supplied by regulator-dummy <6>[ 0.216579] vdd3p0: supplied by regulator-dummy <6>[ 0.221308] vdd2p5: supplied by regulator-dummy <6>[ 0.226153] vddarm: supplied by regulator-dummy <6>[ 0.231048] vddpu: supplied by regulator-dummy <6>[ 0.235470] vddsoc: supplied by regulator-dummy <6>[ 0.254094] No ATAGs? <6>[ 0.254227] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262181] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271635] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278525] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290353] Serial: AMBA PL011 UART driver <6>[ 0.294205] console [pstore-1] enabled <6>[ 0.296027] pstore: Registered ramoops as persistent store backend <6>[ 0.302312] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330592] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340045] vgaarb: loaded <5>[ 0.340985] SCSI subsystem initialized <6>[ 0.344600] usbcore: registered new interface driver usbfs <6>[ 0.349946] usbcore: registered new interface driver hub <6>[ 0.355531] usbcore: registered new device driver usb <6>[ 0.362016] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365771] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.371858] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376287] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382260] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386794] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.393915] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397578] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407003] PTP clock support registered <6>[ 0.411375] EDAC MC: Ver: 3.0.0 <6>[ 0.417267] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.480244] NET: Registered protocol family 2 <6>[ 0.482440] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490214] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.496919] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.504318] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.511062] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.517731] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.523725] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.530487] NET: Registered protocol family 1 <6>[ 0.535454] RPC: Registered named UNIX socket transport module. <6>[ 0.541115] RPC: Registered udp transport module. <6>[ 0.546047] RPC: Registered tcp transport module. <6>[ 0.551018] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.558182] Trying to unpack rootfs image as initramfs... <6>[ 1.669503] Freeing initrd memory: 13004K <4>[ 1.671398] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.678687] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.688648] Initialise system trusted keyrings <6>[ 1.691688] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.704030] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.708016] NFS: Registering the id_resolver key type <5>[ 1.712638] Key type id_resolver registered <5>[ 1.717018] Key type id_legacy registered <6>[ 1.721360] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.728169] Key type asymmetric registered <5>[ 1.730246] Asymmetric key parser 'x509' registered <6>[ 1.735417] bounce: pool size: 64 pages <6>[ 1.739532] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.747125] io scheduler noop registered <6>[ 1.751314] io scheduler deadline registered <6>[ 1.756035] io scheduler cfq registered (default) <6>[ 1.760802] io scheduler mq-deadline registered <6>[ 1.765566] io scheduler kyber registered <6>[ 1.791449] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.796009] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.803132] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.810429] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.830461] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.833851] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.841696] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.847914] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.855797] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.857291] PU : no governor for states <6>[ 1.865399] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.869487] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.940368] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.947671] SuperH (H)SCI(F) driver initialized <6>[ 1.950516] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.959323] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.970246] console [ttymxc1] enabled <6>[ 1.970246] console [ttymxc1] enabled <6>[ 1.975227] bootconsole [ec_imx21] disabled <6>[ 1.975227] bootconsole [ec_imx21] disabled <6>[ 1.985314] msm_serial: driver initialized <6>[ 1.991578] STMicroelectronics ASC driver initialized <6>[ 1.998772] STM32 USART driver initialized <4>[ 2.013783] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.022504] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.029510] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.036268] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.045310] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.052480] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.067240] brd: module loaded <6>[ 2.077321] loop: module loaded <6>[ 2.083891] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.092108] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.100401] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.108861] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.119639] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.126896] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.135984] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.146771] scsi host0: ahci-imx <6>[ 2.150836] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.169679] CAN device driver interface <6>[ 2.175000] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.182098] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.191055] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.200162] pps pps0: new PPS source ptp0 <6>[ 2.230963] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.238417] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.244517] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.250776] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.258021] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.269695] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.277430] usbcore: registered new interface driver pegasus <6>[ 2.283396] usbcore: registered new interface driver asix <6>[ 2.289112] usbcore: registered new interface driver ax88179_178a <6>[ 2.295503] usbcore: registered new interface driver cdc_ether <6>[ 2.301669] usbcore: registered new interface driver smsc75xx <6>[ 2.307755] usbcore: registered new interface driver smsc95xx <6>[ 2.313803] usbcore: registered new interface driver net1080 <6>[ 2.319780] usbcore: registered new interface driver cdc_subset <6>[ 2.325997] usbcore: registered new interface driver zaurus <6>[ 2.331920] usbcore: registered new interface driver cdc_ncm <6>[ 2.340743] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.347561] ehci-pci: EHCI PCI platform driver <6>[ 2.352311] ehci-platform: EHCI generic platform driver <6>[ 2.358105] ehci-orion: EHCI orion driver <6>[ 2.362594] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.367049] ehci-st: EHCI STMicroelectronics driver <6>[ 2.372393] ehci-exynos: EHCI EXYNOS driver <6>[ 2.377022] ehci-atmel: EHCI Atmel driver <6>[ 2.381496] tegra-ehci: Tegra EHCI driver <6>[ 2.385980] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.392458] ohci-pci: OHCI PCI platform driver <6>[ 2.397218] ohci-platform: OHCI generic platform driver <6>[ 2.402979] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.407457] ohci-st: OHCI STMicroelectronics driver <6>[ 2.412781] ohci-atmel: OHCI Atmel driver <6>[ 2.418086] usbcore: registered new interface driver usb-storage <6>[ 2.426617] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.438674] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.448787] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.453957] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.487306] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.488779] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.493618] hub 1-0:1.0: USB hub found <6>[ 2.498700] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.502730] hub 1-0:1.0: 1 port detected <6>[ 2.509222] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.519578] i2c /dev entries driver <6>[ 2.538838] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.550238] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.556686] sdhci: Copyright(c) Pierre Ossman <6>[ 2.563609] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.571851] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.578679] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.584114] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.589631] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.629505] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.637571] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.643101] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.682932] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.694348] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.701613] usbcore: registered new interface driver usbhid <6>[ 2.707478] usbhid: USB HID core driver <6>[ 2.717484] NET: Registered protocol family 10 <6>[ 2.723254] Segment Routing with IPv6 <6>[ 2.727304] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.734027] NET: Registered protocol family 17 <6>[ 2.738784] can: controller area network core (rev 20170425 abi 9) <6>[ 2.745305] NET: Registered protocol family 29 <6>[ 2.750043] can: raw protocol (rev 20170425) <6>[ 2.754583] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.760533] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.766692] Key type dns_resolver registered <6>[ 2.772263] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.778042] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.783764] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.790234] ThumbEE CPU extension supported. <5>[ 2.794783] Registering SWP/SWPB emulation handler <6>[ 2.797320] usb 1-1: new high-speed USB device number 2 using ci_hdrc <5>[ 2.807066] Loading compiled-in X.509 certificates <6>[ 2.810707] mmc0: new high speed SDHC card at address e624 <6>[ 2.813727] pstore: Using compression: deflate <6>[ 2.819976] mmcblk0: mmc0:e624 SL16G 14.8 GiB <4>[ 2.834793] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.835413] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 2.842512] GPT:29296874 != 31116287 <6>[ 2.849909] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 2.853684] GPT:Alternate GPT header not at the end of the disk. <6>[ 2.862162] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 2.867018] GPT:29296874 != 31116287 <6>[ 2.874492] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.878281] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.878324] mmcblk0: p1 p2 p3 <4>[ 2.886843] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.902850] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.909882] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.917870] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.926876] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.934021] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.942556] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.952987] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.960391] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.968643] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.976116] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.984633] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.993313] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.000309] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.008108] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.017109] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.024269] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.031982] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.039369] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.047508] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.055000] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.063467] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.072146] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.079150] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.086891] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.095921] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.103081] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.111698] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.118579] hub 1-1:1.0: USB hub found <6>[ 3.122731] hctosys: unable to open rtc device (rtc0) <6>[ 3.128630] hub 1-1:1.0: 3 ports detected <6>[ 3.133549] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.141134] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.149531] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.157024] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.165614] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.174300] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.181442] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.189276] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.198308] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.205460] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.213464] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.220861] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.229029] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.236509] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.244987] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.253667] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.260629] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 3.267868] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <4>[ 3.268384] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.282695] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 3.291603] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.304796] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.397901] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.417295] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.447347] Sending DHCP requests ., OK <6>[ 6.491511] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 6.499856] IP-Config: Complete: <6>[ 6.503372] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.514121] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 6.522260] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.522268] nameserver0=192.168.201.1 <6>[ 6.541165] Freeing unused kernel memory: 2048K <6>[ 6.557655] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.688245] udevd[112]: starting version 3.2.9 <5>[ 6.693816] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.700851] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.707744] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.721457] udevd[112]: specified user 'tss' unknown <27>[ 6.726895] udevd[112]: specified group 'tss' unknown <30>[ 6.734298] udevd[113]: starting eudev-3.2.9 <6>[ 7.083717] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.117501] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.126485] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.135156] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.143214] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.161911] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.169579] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.180620] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.187417] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.189630] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.194572] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.203281] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.298691] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.306998] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.316083] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.326579] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.334750] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.342543] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.351153] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.358860] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.409320] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.443409] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.449825] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.458166] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.467355] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.476103] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.483380] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.491953] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.492946] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.507379] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.514551] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.524532] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.531821] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.532759] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.544871] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.553674] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.561460] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.569786] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 7.572285] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.586418] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.594122] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.635912] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.645005] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.653885] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.662381] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.670678] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.680003] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.689778] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.699168] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.707914] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.715704] panel-simple panel-lcd: Dropping the link to regulator.0 done Saving random seed: <5>[ 7.875186] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.958940] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-14808755/environment / # /lava-14808755/bin/lava-test-runner /lava-14808755/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-14808755/0/tests/0_dmesg + cat uuid <8>[ 8.562492] + UUID=14808755_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.606387] <8>[ 8.646553] <8>[ 8.686868] + set +x <8>[ 8.696813] / #