Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3028 device /dev/ttyimx6qp-sabresd-1 [115200 N81] (Debian GNU/Linux) U-Boot 2017.03 (Jan 20 2018 - 10:43:25 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 22C Reset cause: POR Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board Board: MX6-SabreSD DRAM: 1 GiB PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial flash target is MMC:1 Net: Warning: ethernet@02188000 using MAC address from ROM eth0: ethernet@02188000 [PRIME] Fastboot: Normal Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.241 (1255 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x12000000 1001321/tftp-deploy-8fhdi8ie/kernel/zImage tftp 0x12000000 1001321/tftp-deploy-8fhdi8ie/kernel/zImage Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1001321/tftp-deploy-8fhdi8ie/kernel/zImage'. Load address: 0x12000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################ 11.5 MiB/s done Bytes transferred = 8507304 (81cfa8 hex) => tftp 0x12C00000 1001321/tftp-deploy-8fhdi8ie/ramdisk/ramdisk.cpio.gz.uboot tftp 0x12C00000 1001321/tftp-deploy-8fhdi8ie/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1001321/tftp-deploy-8fhdi8ie/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x12c00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################## 9.1 MiB/s done Bytes transferred = 9259751 (8d4ae7 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x18000000 1001321/tftp-deploy-8fhdi8ie/dtb/imx6qp-sabresd.dtb tftp 0x18000000 1001321/tftp-deploy-8fhdi8ie/dtb/imx6qp-sabresd.dtb Using ethernet@02188000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.241; sending through gateway 172.16.1.4 Filename '1001321/tftp-deploy-8fhdi8ie/dtb/imx6qp-sabresd.dtb'. Load address: 0x18000000 Loading: *### 5 MiB/s done Bytes transferred = 42366 (a57e hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x12000000 0x12C00000 0x18000000 bootz 0x12000000 0x12C00000 0x18000000 Kernel image @ 0x12000000 [ 0x000000 - 0x81cfa8 ] ## Loading init Ramdisk from Legacy Image at 12c00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9259687 Bytes = 8.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 Using Device Tree in place at 18000000, end 1800d57d Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.251-cip77 (KernelCI@build-j333439-arm-gcc-10-imx-v6-v7-defconfig-fbttl) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Jul 8 22:20:13 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad Plus SABRE Smart Device Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x02020000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37928 r8192 d23512 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939620K/1048576K available (11264K kernel code, 880K rwdata, 3612K rodata, 1024K init, 7652K bss, 43420K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (12256 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 881 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7653 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.020167] Console: colour dummy device 80x30 <4>[ 0.023053] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.031088] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.035405] ... MAX_LOCK_DEPTH: 48 <4>[ 0.039865] ... MAX_LOCKDEP_KEYS: 8191 <4>[ 0.044453] ... CLASSHASH_SIZE: 4096 <4>[ 0.049086] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.053761] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.058482] ... CHAINHASH_SIZE: 32768 <4>[ 0.063158] memory used by lock dependency info: 4655 kB <4>[ 0.068835] per task-struct memory footprint: 1536 bytes <6>[ 0.074532] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.084937] pid_max: default: 32768 minimum: 301 <6>[ 0.090177] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.096702] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.106365] CPU: Testing write buffer coherency: ok <6>[ 0.109098] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.115816] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.122579] Setting up static identity map for 0x10100000 - 0x10100078 <6>[ 0.127726] rcu: Hierarchical SRCU implementation. <6>[ 0.133951] smp: Bringing up secondary CPUs ... <6>[ 0.139398] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.139409] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.150824] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.150835] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.161518] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.161529] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.170982] smp: Brought up 1 node, 4 CPUs <6>[ 0.174957] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.181506] CPU: All CPU(s) started in SVC mode. <6>[ 0.189330] devtmpfs: initialized <6>[ 0.217741] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.225216] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.233079] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.243220] pinctrl core: initialized pinctrl subsystem <6>[ 0.251129] NET: Registered protocol family 16 <6>[ 0.273250] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.280943] cpuidle: using governor menu <6>[ 0.282490] CPU identified as i.MX6QP, silicon rev 1.0 <3>[ 0.304207] anatop_regulator 20c8000.anatop:regulator-1p1: failed to register vdd1p1 <6>[ 0.310087] vdd3p0: supplied by regulator-dummy <3>[ 0.315574] anatop_regulator 20c8000.anatop:regulator-2p5: failed to register vdd2p5 <3>[ 0.322842] anatop_regulator 20c8000.anatop:regulator-vddcore: failed to register vddarm <3>[ 0.332128] anatop_regulator 20c8000.anatop:regulator-vddsoc: failed to register vddsoc <6>[ 0.365164] No ATAGs? <6>[ 0.365597] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.373700] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.382175] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.390182] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.457643] mxs-dma 110000.dma-apbh: initialized <6>[ 0.466472] vgaarb: loaded <5>[ 0.467608] SCSI subsystem initialized <6>[ 0.471807] usbcore: registered new interface driver usbfs <6>[ 0.476613] usbcore: registered new interface driver hub <6>[ 0.482029] usbcore: registered new device driver usb <6>[ 0.490602] i2c i2c-0: IMX I2C adapter registered <6>[ 0.492748] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.500129] i2c i2c-1: IMX I2C adapter registered <6>[ 0.503271] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.510152] i2c i2c-2: IMX I2C adapter registered <6>[ 0.513796] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.519757] media: Linux media interface: v0.10 <6>[ 0.524219] videodev: Linux video capture interface: v2.00 <6>[ 0.530373] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.535095] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.544588] PTP clock support registered <6>[ 0.549452] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.558349] Bluetooth: Core ver 2.22 <6>[ 0.559477] NET: Registered protocol family 31 <6>[ 0.564040] Bluetooth: HCI device and connection manager initialized <6>[ 0.570795] Bluetooth: HCI socket layer initialized <6>[ 0.575799] Bluetooth: L2CAP socket layer initialized <6>[ 0.581314] Bluetooth: SCO socket layer initialized <6>[ 0.588275] clocksource: Switched to clocksource mxc_timer1 <5>[ 0.809799] VFS: Disk quotas dquot_6.6.0 <6>[ 0.811276] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 0.845550] NET: Registered protocol family 2 <6>[ 0.847900] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.856765] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 20480 bytes) <6>[ 0.862478] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.869806] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) <6>[ 0.877363] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.883730] UDP hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.889399] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) <6>[ 0.896348] NET: Registered protocol family 1 <6>[ 0.902358] RPC: Registered named UNIX socket transport module. <6>[ 0.906584] RPC: Registered udp transport module. <6>[ 0.911618] RPC: Registered tcp transport module. <6>[ 0.916494] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.925256] Trying to unpack rootfs image as initramfs... <6>[ 1.863120] Freeing initrd memory: 9044K <4>[ 1.865690] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.872604] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.885683] Initialise system trusted keyrings <6>[ 1.888352] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <5>[ 1.909940] NFS: Registering the id_resolver key type <5>[ 1.912547] Key type id_resolver registered <5>[ 1.916864] Key type id_legacy registered <6>[ 1.921466] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. <6>[ 1.928968] fuse init (API version 7.27) <5>[ 1.944422] Key type asymmetric registered <5>[ 1.946081] Asymmetric key parser 'x509' registered <6>[ 1.951333] bounce: pool size: 64 pages <6>[ 1.955266] io scheduler noop registered <6>[ 1.959392] io scheduler deadline registered <6>[ 1.964152] io scheduler cfq registered (default) <6>[ 1.968876] io scheduler mq-deadline registered <6>[ 1.973609] io scheduler kyber registered <4>[ 1.984147] pwm-backlight backlight-lvds: backlight-lvds supply power not found, using dummy regulator <6>[ 1.991452] pwm-backlight backlight-lvds: Linked as a consumer to regulator.0 <4>[ 2.008916] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 2.016073] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <4>[ 2.021183] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 2.030417] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 2.037842] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 2.047546] pfuze100-regulator 1-0008: Full layer: 2, Metal layer: 1 <6>[ 2.052335] pfuze100-regulator 1-0008: FAB: 0, FIN: 0 <6>[ 2.056635] pfuze100-regulator 1-0008: pfuze100 found. <6>[ 2.090558] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 26, base_baud = 5000000) is a IMX <6>[ 2.099937] console [ttymxc0] enabled <6>[ 2.099937] console [ttymxc0] enabled <6>[ 2.104972] bootconsole [ec_imx21] disabled <6>[ 2.104972] bootconsole [ec_imx21] disabled <4>[ 2.125303] panel-simple panel: panel supply power not found, using dummy regulator <6>[ 2.133544] panel-simple panel: Linked as a consumer to regulator.0 <6>[ 2.145848] imx-ipu-prg 21cc000.prg: Linked as a consumer to 21c8000.pre <6>[ 2.152925] imx-ipu-prg 21cc000.prg: Linked as a consumer to 21c9000.pre <6>[ 2.159985] imx-ipu-prg 21cc000.prg: Linked as a consumer to 21ca000.pre <6>[ 2.167524] imx-ipu-prg 21cd000.prg: Linked as a consumer to 21cb000.pre <6>[ 2.174594] imx-ipu-prg 21cd000.prg: Linked as a consumer to 21c9000.pre <6>[ 2.181650] imx-ipu-prg 21cd000.prg: Linked as a consumer to 21ca000.pre <6>[ 2.189649] imx-ipuv3 2400000.ipu: Linked as a consumer to 21cc000.prg <6>[ 2.198659] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 2.203843] imx-ipuv3 2800000.ipu: Linked as a consumer to 21cd000.prg <6>[ 2.214137] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 2.221235] [drm] No driver support for vblank timestamp query. <6>[ 2.228802] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops) <6>[ 2.236793] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops) <6>[ 2.244871] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops) <6>[ 2.252926] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops) <6>[ 2.261657] dwhdmi-imx 120000.hdmi: Detected HDMI TX controller v1.30a with HDCP (DWC HDMI 3D TX PHY) <6>[ 2.277044] imx-drm display-subsystem: bound 120000.hdmi (ops dw_hdmi_imx_ops) <6>[ 2.285207] imx-drm display-subsystem: bound ldb (ops imx_ldb_ops) <6>[ 2.360808] Console: switching to colour frame buffer device 128x48 <6>[ 2.383060] imx-drm display-subsystem: fb0: DRM emulated frame buffer device <6>[ 2.394742] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0 <6>[ 2.403070] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 2.431660] brd: module loaded <6>[ 2.463641] loop: module loaded <3>[ 2.479535] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 <6>[ 2.486365] spi_imx 2008000.ecspi: probed <6>[ 2.493748] CAN device driver interface <4>[ 2.500437] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.510144] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.520168] pps pps0: new PPS source ptp0 <6>[ 2.561819] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.569832] usbcore: registered new interface driver asix <6>[ 2.575600] usbcore: registered new interface driver ax88179_178a <6>[ 2.582120] usbcore: registered new interface driver cdc_ether <6>[ 2.588359] usbcore: registered new interface driver net1080 <6>[ 2.594384] usbcore: registered new interface driver cdc_subset <6>[ 2.600708] usbcore: registered new interface driver zaurus <6>[ 2.606703] usbcore: registered new interface driver cdc_ncm <6>[ 2.612683] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.619527] ehci-pci: EHCI PCI platform driver <6>[ 2.624342] ehci-mxc: Freescale On-Chip EHCI Host driver <6>[ 2.630845] usbcore: registered new interface driver usb-storage <6>[ 2.640838] usb_otg_vbus: supplied by SWBST <6>[ 2.645830] imx_usb 2184000.usb: Linked as a consumer to regulator.7 <6>[ 2.661644] usb_h1_vbus: supplied by SWBST <6>[ 2.666422] imx_usb 2184200.usb: Linked as a consumer to regulator.8 <6>[ 2.677486] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.683071] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.718349] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.728381] hub 1-0:1.0: USB hub found <6>[ 2.732674] hub 1-0:1.0: 1 port detected <3>[ 2.743571] egalax_ts 2-0004: Failed to read firmware version <4>[ 2.749803] egalax_ts: probe of 2-0004 failed with error -11 <6>[ 2.761841] snvs_rtc 20cc000.snvs:snvs-rtc-lp: registered as rtc0 <6>[ 2.771478] i2c /dev entries driver <6>[ 2.784772] imx2-wdt 20c0000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.791809] Bluetooth: HCI UART driver ver 2.3 <6>[ 2.796539] Bluetooth: HCI UART protocol H4 registered <6>[ 2.802506] Bluetooth: HCI UART protocol LL registered <6>[ 2.809560] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.816056] sdhci: Copyright(c) Pierre Ossman <6>[ 2.820752] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.828086] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO <6>[ 2.833671] sdhci-esdhc-imx 2194000.usdhc: Got WP GPIO <6>[ 2.875684] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA <6>[ 2.884405] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.889954] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.930402] mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.976485] mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.991867] mmc1: new high speed SDHC card at address aaaa <6>[ 3.004876] caam 2100000.caam: Entropy delay = 3200 <6>[ 3.016310] mmcblk1: mmc1:aaaa SS08G 7.40 GiB <6>[ 3.061397] mmc2: new DDR MMC card at address 0001 <6>[ 3.069003] mmcblk2: mmc2:0001 Q2J55L 7.13 GiB <6>[ 3.070986] caam 2100000.caam: Instantiated RNG4 SH0 <6>[ 3.075364] mmcblk2boot0: mmc2:0001 Q2J55L partition 1 2.00 MiB <6>[ 3.087000] mmcblk2boot1: mmc2:0001 Q2J55L partition 2 2.00 MiB <6>[ 3.094367] mmcblk2rpmb: mmc2:0001 Q2J55L partition 3 4.00 MiB, chardev (244:0) <6>[ 3.131748] caam 2100000.caam: Instantiated RNG4 SH1 <6>[ 3.137005] caam 2100000.caam: device ID = 0x0a16010000000000 (Era 4) <6>[ 3.143766] caam 2100000.caam: job rings = 2, qi = 0 <6>[ 3.166170] caam algorithms registered in /proc/crypto <6>[ 3.177730] caam_jr 2101000.jr0: registering rng-caam <6>[ 3.184715] usbcore: registered new interface driver usbhid <6>[ 3.190629] usbhid: USB HID core driver <6>[ 3.200844] imx-media: subdev ipu1_vdic bound <6>[ 3.205806] imx-media: subdev ipu2_vdic bound <6>[ 3.210940] imx-media: subdev ipu1_ic_prp bound <6>[ 3.217143] ipu1_ic_prpenc: Registered ipu1_ic_prpenc capture as /dev/video0 <6>[ 3.224858] imx-media: subdev ipu1_ic_prpenc bound <6>[ 3.230597] ipu1_ic_prpvf: Registered ipu1_ic_prpvf capture as /dev/video1 <6>[ 3.237805] imx-media: subdev ipu1_ic_prpvf bound <6>[ 3.243032] imx-media: subdev ipu2_ic_prp bound <6>[ 3.248564] ipu2_ic_prpenc: Registered ipu2_ic_prpenc capture as /dev/video2 <6>[ 3.255953] imx-media: subdev ipu2_ic_prpenc bound <6>[ 3.261675] ipu2_ic_prpvf: Registered ipu2_ic_prpvf capture as /dev/video3 <6>[ 3.268947] imx-media: subdev ipu2_ic_prpvf bound <6>[ 3.275851] ipu1_csi0: Registered ipu1_csi0 capture as /dev/video4 <6>[ 3.282402] imx-media: subdev ipu1_csi0 bound <6>[ 3.287730] ipu1_csi1: Registered ipu1_csi1 capture as /dev/video5 <6>[ 3.294275] imx-media: subdev ipu1_csi1 bound <6>[ 3.299658] ipu2_csi0: Registered ipu2_csi0 capture as /dev/video6 <6>[ 3.306123] imx-media: subdev ipu2_csi0 bound <6>[ 3.311511] ipu2_csi1: Registered ipu2_csi1 capture as /dev/video7 <6>[ 3.317978] imx-media: subdev ipu2_csi1 bound <6>[ 3.323449] imx-media: subdev imx6-mipi-csi2 bound <6>[ 3.337639] wm8962 0-001a: Linked as a consumer to regulator.9 <6>[ 3.349444] wm8962 0-001a: customer id 0 revision D <6>[ 3.380739] fsl-asoc-card sound: ASoC: CPU DAI (null) not registered <4>[ 3.391105] fsl-ssi-dai 202c000.ssi: No cache defaults, reading back from HW <6>[ 3.405185] NET: Registered protocol family 10 <6>[ 3.413543] Segment Routing with IPv6 <6>[ 3.417716] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.425890] NET: Registered protocol family 17 <6>[ 3.430703] can: controller area network core (rev 20170425 abi 9) <6>[ 3.437342] NET: Registered protocol family 29 <6>[ 3.442131] can: raw protocol (rev 20170425) <6>[ 3.446836] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.452860] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 3.459422] Key type dns_resolver registered <6>[ 3.465723] vddpu: supplied by SW1C <6>[ 3.469989] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 3.476194] cpu cpu0: Dropping the link to regulator.5 <5>[ 3.482553] Registering SWP/SWPB emulation handler <5>[ 3.489366] Loading compiled-in X.509 certificates <6>[ 3.577157] vdd1p1: supplied by VGEN5 <6>[ 3.583304] vdd2p5: supplied by VGEN5 <6>[ 3.588427] vddarm: supplied by SW2 <6>[ 3.593278] vddsoc: supplied by SW1C <6>[ 3.599240] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 3.607958] PU : no governor for states <6>[ 3.612305] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 3.625788] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops) <6>[ 3.632406] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops) <6>[ 3.638945] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops) <6>[ 3.644896] etnaviv-gpu 130000.gpu: model: GC3000, revision: 5450 <6>[ 3.655290] etnaviv-gpu 134000.gpu: model: GC320, revision: 5303 <6>[ 3.663834] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1216 <6>[ 3.670293] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 3.678807] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 1 <6>[ 3.687215] imx-media: subdev ipu1_csi0_mux bound <6>[ 3.693101] imx-media: subdev ipu2_csi1_mux bound <6>[ 3.704132] input: WM8962 Beep Generator as /devices/soc0/soc/2100000.aips-bus/21a0000.i2c/i2c-0/0-001a/input/input1 <6>[ 3.778369] fsl-asoc-card sound: wm8962 <-> 202c000.ssi mapping ok <6>[ 3.792344] cpu cpu0: Linked as a consumer to regulator.28 <6>[ 3.798457] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 3.804421] cpu cpu0: Linked as a consumer to regulator.29 <6>[ 3.819112] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 3.834779] input: gpio-keys as /devices/soc0/gpio-keys/input/input2 <6>[ 3.844835] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:35 UTC (35) <6>[ 3.960791] Atheros 8031 ethernet 2188000.ethernet-1:01: attached PHY driver [Atheros 8031 ethernet] (mii_bus:phy_addr=2188000.ethernet-1:01, irq=POLL) <6>[ 3.976892] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 7.120959] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.130055] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.158261] Sending DHCP requests .., OK <6>[ 10.122903] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.241 <6>[ 10.130921] IP-Config: Complete: <6>[ 10.134463] device=eth0, hwaddr=00:04:9f:05:b8:c3, ipaddr=172.16.1.241, mask=255.255.255.0, gw=172.16.1.4 <6>[ 10.144878] host=172.16.1.241, domain=example.org, nis-domain=(none) <6>[ 10.152060] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 10.152072] nameserver0=172.16.1.4 <5>[ 10.167535] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 10.223010] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <6>[ 10.231177] ALSA device list: <6>[ 10.234430] #0: wm8962-audio <4>[ 10.238847] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 10.247804] cfg80211: failed to load regulatory.db <6>[ 10.257279] Freeing unused kernel memory: 1024K <6>[ 10.309482] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.612470] udevd[182]: starting version 3.2.9 <5>[ 10.619767] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.627359] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.634465] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 10.651146] udevd[182]: specified user 'tss' unknown <27>[ 10.656641] udevd[182]: specified group 'tss' unknown <30>[ 10.668470] udevd[183]: starting eudev-3.2.9 <4>[ 11.156759] coda 2040000.vpu: Direct firmware load for vpu_fw_imx6q.bin failed with error -2 <4>[ 11.168536] coda 2040000.vpu: Direct firmware load for vpu/vpu_fw_imx6q.bin failed with error -2 <4>[ 11.179592] coda 2040000.vpu: Direct firmware load for v4l-coda960-imx6q.bin failed with error -2 <3>[ 11.193448] coda 2040000.vpu: firmware request failed <6>[ 11.269984] ov5640 1-003c: Linked as a consumer to regulator.23 <6>[ 11.277805] ov5640 1-003c: Linked as a consumer to regulator.21 <6>[ 11.286097] ov5640 1-003c: Linked as a consumer to regulator.22 <3>[ 11.348415] ov5640 1-003c: ov5640_read_reg: error: reg=300a <3>[ 11.354331] ov5640 1-003c: ov5640_check_chip_id: failed to read chip identifier <6>[ 11.380271] ov5640 1-003c: Dropping the link to regulator.23 <6>[ 11.387190] ov5640 1-003c: Dropping the link to regulator.21 <6>[ 11.396068] ov5640 1-003c: Dropping the link to regulator.22 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 11.777249] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1001321/environment . /lava-1001321/environment / # /lava-1001321/bin/lava-test-runner /lava-1001321/0 /lava-1001321/bin/lava-test-runner /lava-1001321/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1001321/0/tests/0_dmesg + cat uuid + UUID=1001321_1.5.2.4.1<8>[ 17.709109] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.796834] <8>[ 17.873614] <8>[ 17.950234] + set +x<8>[ 17.961049] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1001321/environment / # . /lava-1001321/environment/lava-1001321/bin/lava-test-runner /lava-1001321/1 / # /lava-1001321/bin/lava-test-runner /lava-1001321/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1001321/1/tests/1_bootrr + cat uuid + UUID=1001321_1.5.2.4.5 <8>[ 23.772119] + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1001321/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1001321/1/../bin/lava-test-case <8>[ 24.870162] /lava-1001321/1/../bin/lava-test-case <8>[ 24.951380] /lava-1001321/1/../bin/lava-test-case <8>[ 24.996833] + set +x<8>[ 25.029963] / #