connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='USBSerialPort', state=<BindingState.bound: 1>, avail=True, host='nuc-1', port=58485, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:58485
connected to 192.168.0.1 (port 58485)
Escape character: Ctrl-\
Type the escape character to get to the prompt.
  RomBOOT

All interupts redirected to AIC
ACT8865: Set REG1/REG2/REG3 power saving mode
ACT8865: The REG5 output 3300mV
ACT8865: The REG6 output 1800mV
ACT8865: Disable ACT8865's I2C interface
HDMI SiI9022: Enter D3 Cold mode
PHY: GMAC0 KSZ8081RNB: Enter power down mode


AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014)

EEPROM: Loading AT24xx information ...
EEPROM: BoardName | [Revid] | VendorName
HW Info: The total size isn't correct

1-Wire: Using default information

1-Wire: Board sn: 0x1012420, revsion: 0x680820

NAND: ONFI flash detected
NAND: Manufacturer ID: 0x2c Chip ID: 0x34
NAND: Disable On-Die ECC
NAND: Initialize PMECC params, cap: 0x8, sector: 0x200
NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000
NAND: Done to load image


U-Boot 2014.07 (Oct 29 2014 - 16:59:40)

CPU: SAMA5D4
Crystal frequency:       12 MHz
CPU clock        :      528 MHz
Master clock     :      176 MHz
DRAM:  512 MiB
NAND:  512 MiB
MMC:   mci: 0
In:    serial
Out:   serial
Err:   serial
Net:   gmac0
Hit any key to stop autoboot:  3 
 0 
U-Boot> setenv autoload no
setenv autoload no
U-Boot> setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
U-Boot> setenv fdt_high 0xffffffff
setenv fdt_high 0xffffffff
U-Boot> dhcp
dhcp
gmac0: PHY present at 0
gmac0: Starting autonegotiation...
gmac0: Autonegotiation complete
gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1)
BOOTP broadcast 1
DHCP client bound to address 192.168.0.136
U-Boot> setenv serverip 192.168.0.2
setenv serverip 192.168.0.2
U-Boot> tftp 0x22100000 2433344/tftp-deploy-ohdoikf7/kernel/zImage
tftp 0x22100000 2433344/tftp-deploy-ohdoikf7/kernel/zImage
gmac0: PHY present at 0
gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1)
Using gmac0 device
TFTP from server 192.168.0.2; our IP address is 192.168.0.136
Filename '2433344/tftp-deploy-ohdoikf7/kernel/zImage'.
Load address: 0x22100000
Loading: *#################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 ######################################
	 2.6 MiB/s
done
Bytes transferred = 4367368 (42a408 hex)
U-Boot> tftp 0x23000000 2433344/tftp-deploy-ohdoikf7/ramdisk/ramdisk.cpio.gz.uboot
tftp 0x23000000 2433344/tftp-deploy-ohdoikf7/ramdisk/ramdisk.cpio.gz.uboot
gmac0: PHY present at 0
gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1)
Using gmac0 device
TFTP from server 192.168.0.2; our IP address is 192.168.0.136
Filename '2433344/tftp-deploy-ohdoikf7/ramdisk/ramdisk.cpio.gz.uboot'.
Load address: 0x23000000
Loading: *#################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 ################################################
	 3.1 MiB/s
done
Bytes transferred = 8326798 (7f0e8e hex)
U-Boot> setenv initrd_size ${filesize}
setenv initrd_size ${filesize}
U-Boot> tftp 0x22000000 2433344/tftp-deploy-ohdoikf7/dtb/at91-sama5d4_xplained.dtb
tftp 0x22000000 2433344/tftp-deploy-ohdoikf7/dtb/at91-sama5d4_xplained.dtb
gmac0: PHY present at 0
gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1)
Using gmac0 device
TFTP from server 192.168.0.2; our IP address is 192.168.0.136
Filename '2433344/tftp-deploy-ohdoikf7/dtb/at91-sama5d4_xplained.dtb'.
Load address: 0x22000000
Loading: *###
	 1.7 MiB/s
done
Bytes transferred = 32907 (808b hex)
U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp'
setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp'
U-Boot> bootz 0x22100000 0x23000000 0x22000000
bootz 0x22100000 0x23000000 0x22000000
Kernel image @ 0x22100000 [ 0x000000 - 0x42a408 ]
## Loading init Ramdisk from Legacy Image at 23000000 ...
   Image Name:   
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8326734 Bytes = 7.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 22000000
   Booting using the fdt blob at 0x22000000
   Using Device Tree in place at 22000000, end 2200b08a

Starting kernel ...

 