Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.2 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 811639/tftp-deploy-1cjucak5/kernel/zImage tftp 0x82000000 811639/tftp-deploy-1cjucak5/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '811639/tftp-deploy-1cjucak5/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 5.2 MiB/s done Bytes transferred = 8724992 (852200 hex) => tftp 0x83000000 811639/tftp-deploy-1cjucak5/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 811639/tftp-deploy-1cjucak5/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '811639/tftp-deploy-1cjucak5/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.1 MiB/s done Bytes transferred = 9408670 (8f909e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 811639/tftp-deploy-1cjucak5/dtb/am335x-boneblack.dtb tftp 0x88000000 811639/tftp-deploy-1cjucak5/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '811639/tftp-deploy-1cjucak5/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *### 4.8 MiB/s done Bytes transferred = 34893 (884d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/811639/extract-nfsrootfs-hcuwnu9g,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/811639/extract-nfsrootfs-hcuwnu9g,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2022-12-24 0:32:04 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9408606 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8800b84c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.269-cip88 (KernelCI@build-j740693-arm-gcc-10-multi-v7-defconfig-vqzrt) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Dec 23 23:03:30 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omapserial0 at MMIO 0x44e09000 (options '') [ 0.000000] bootconsole [omapserial0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/811639/extract-nfsrootfs-hcuwnu9g,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 421204K/522240K available (12288K kernel code, 1597K rwdata, 4676K rodata, 2048K init, 394K bss, 35500K reserved, 65536K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0000000 - 0xff800000 ( 504 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xdfe00000 ( 510 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz <6>[ 0.000014] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008239] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.017967] OMAP clocksource: timer1 at 24000000 Hz <2>[ 0.026850] timer_probe: no matching timers found <6>[ 0.032193] Console: colour dummy device 80x30 <6>[ 0.036991] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.075866] pid_max: default: 32768 minimum: 301 <6>[ 0.081032] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.088013] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.096171] CPU: Testing write buffer coherency: ok <6>[ 0.101449] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.107248] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.113409] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.121709] rcu: Hierarchical SRCU implementation. <6>[ 0.129485] EFI services will not be available. <6>[ 0.134499] smp: Bringing up secondary CPUs ... <6>[ 0.139360] smp: Brought up 1 node, 1 CPU <6>[ 0.143705] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.150413] CPU: All CPU(s) started in SVC mode. <6>[ 0.156797] devtmpfs: initialized <6>[ 0.167419] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.176044] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.186380] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.196728] pinctrl core: initialized pinctrl subsystem <6>[ 0.204161] DMI not present or invalid. <6>[ 0.209012] NET: Registered protocol family 16 <6>[ 0.216228] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.249257] l4_wkup_cm:clk:0010:0: failed to disable <6>[ 0.296220] cpuidle: using governor menu <6>[ 0.307518] OMAP GPIO hardware version 0.1 <6>[ 0.323697] No ATAGs? <6>[ 0.323708] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 0.337636] Serial: AMBA PL011 UART driver <6>[ 0.359968] edma 49000000.edma: TI EDMA DMA engine driver <6>[ 0.369205] vgaarb: loaded <5>[ 0.373094] SCSI subsystem initialized <6>[ 0.377848] usbcore: registered new interface driver usbfs <6>[ 0.383762] usbcore: registered new interface driver hub <6>[ 0.389451] usbcore: registered new device driver usb <6>[ 0.396309] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.401638] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.411253] PTP clock support registered <6>[ 0.415683] EDAC MC: Ver: 3.0.0 <6>[ 0.422022] clocksource: Switched to clocksource timer1 <6>[ 0.488171] NET: Registered protocol family 2 <6>[ 0.493223] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.500729] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.508850] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.516313] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.523190] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.530012] UDP hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.536221] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.543032] NET: Registered protocol family 1 <6>[ 0.548437] RPC: Registered named UNIX socket transport module. <6>[ 0.554764] RPC: Registered udp transport module. <6>[ 0.559777] RPC: Registered tcp transport module. <6>[ 0.564889] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.572402] Trying to unpack rootfs image as initramfs... <6>[ 1.156672] Freeing initrd memory: 9192K <6>[ 1.161708] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 1.172749] Initialise system trusted keyrings <6>[ 1.177929] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 1.190993] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.198146] NFS: Registering the id_resolver key type <5>[ 1.203626] Key type id_resolver registered <5>[ 1.208102] Key type id_legacy registered <6>[ 1.212539] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.219432] Key type asymmetric registered <5>[ 1.223916] Asymmetric key parser 'x509' registered <6>[ 1.229163] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.236985] io scheduler noop registered <6>[ 1.241237] io scheduler deadline registered <6>[ 1.246078] io scheduler cfq registered (default) <6>[ 1.251091] io scheduler mq-deadline registered <6>[ 1.256029] io scheduler kyber registered <6>[ 1.266160] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 1.336203] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.346229] SuperH (H)SCI(F) driver initialized <6>[ 1.351934] msm_serial: driver initialized <6>[ 1.356739] omap_uart 44e09000.serial: no wakeirq for uart0 <6>[ 1.362771] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 30, base_baud = 3000000) is a OMAP UART0 �f��6v&VF�6{s�{c+����{��Vs c+#k <6>[ 1.372514] console [ttyO0] enabled <6>[ 1.380187] bootconsole [omapserial0] disabled <6>[ 1.380187] bootconsole [omapserial0] disabled <6>[ 1.390550] STMicroelectronics ASC driver initialized <6>[ 1.397128] STM32 USART driver initialized <6>[ 1.403178] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 1.415806] random: crng init done <6>[ 1.428876] brd: module loaded <6>[ 1.439751] loop: module loaded <6>[ 1.452803] CAN device driver interface <6>[ 1.458029] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.465203] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.471590] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.478180] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.485772] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.562034] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 1.570349] davinci_mdio 4a101000.mdio: detected phy mask fffffffe <6>[ 1.591535] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 1.604052] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 1.611407] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 1.618469] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 1.625953] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.634163] usbcore: registered new interface driver pegasus <6>[ 1.640409] usbcore: registered new interface driver asix <6>[ 1.646418] usbcore: registered new interface driver ax88179_178a <6>[ 1.653133] usbcore: registered new interface driver cdc_ether <6>[ 1.659555] usbcore: registered new interface driver smsc75xx <6>[ 1.665908] usbcore: registered new interface driver smsc95xx <6>[ 1.672247] usbcore: registered new interface driver net1080 <6>[ 1.678475] usbcore: registered new interface driver cdc_subset <6>[ 1.685035] usbcore: registered new interface driver zaurus <6>[ 1.691196] usbcore: registered new interface driver cdc_ncm <6>[ 1.699462] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.706644] ehci-pci: EHCI PCI platform driver <6>[ 1.711623] ehci-platform: EHCI generic platform driver <6>[ 1.717631] ehci-orion: EHCI orion driver <6>[ 1.722304] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.726904] ehci-st: EHCI STMicroelectronics driver <6>[ 1.732448] ehci-exynos: EHCI EXYNOS driver <6>[ 1.737220] ehci-atmel: EHCI Atmel driver <6>[ 1.741800] tegra-ehci: Tegra EHCI driver <6>[ 1.746435] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.753249] ohci-pci: OHCI PCI platform driver <6>[ 1.758241] ohci-platform: OHCI generic platform driver <6>[ 1.764212] SPEAr-ohci: OHCI SPEAr driver <6>[ 1.768813] ohci-st: OHCI STMicroelectronics driver <6>[ 1.774366] ohci-atmel: OHCI Atmel driver <6>[ 1.779521] usbcore: registered new interface driver usb-storage <6>[ 1.790651] i2c /dev entries driver <6>[ 1.806132] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.812976] sdhci: Copyright(c) Pierre Ossman <6>[ 1.818951] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 1.828413] omap_hsmmc 48060000.mmc: Got CD GPIO <6>[ 1.834046] omap_hsmmc 48060000.mmc: Linked as a consumer to regulator.1 <6>[ 1.865942] omap_hsmmc 481d8000.mmc: Linked as a consumer to regulator.1 <6>[ 1.900040] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.907968] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.917509] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.925517] usbcore: registered new interface driver usbhid <6>[ 1.931636] usbhid: USB HID core driver <6>[ 1.940319] NET: Registered protocol family 10 <6>[ 1.946864] Segment Routing with IPv6 <6>[ 1.951075] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.958340] NET: Registered protocol family 17 <6>[ 1.963340] can: controller area network core (rev 20170425 abi 9) <6>[ 1.970176] NET: Registered protocol family 29 <6>[ 1.975141] can: raw protocol (rev 20170425) <6>[ 1.979889] can: broadcast manager protocol (rev 20170425 t) <6>[ 1.986113] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 1.992808] Key type dns_resolver registered <6>[ 1.997704] ThumbEE CPU extension supported. <5>[ 2.002531] Registering SWP/SWPB emulation handler <3>[ 2.007836] omap_voltage_late_init: Voltage driver support not added <5>[ 2.016703] Loading compiled-in X.509 certificates <6>[ 2.078991] mmc1: new high speed MMC card at address 0001 <6>[ 2.086283] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 2.091825] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 2.098898] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 2.105813] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 2.114017] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 2.121348] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 2.129382] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 2.136852] mmcblk1: p1 <6>[ 2.265270] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 2.272415] hctosys: unable to open rtc device (rtc0) <6>[ 2.291771] net eth0: initializing cpsw version 1.12 (0) <6>[ 2.393093] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 2.412226] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.552895] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 5.562034] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.592018] Sending DHCP requests ., OK <6>[ 5.636319] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.2 <6>[ 5.644735] IP-Config: Complete: <6>[ 5.648390] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.2, mask=255.255.255.0, gw=192.168.11.1 <6>[ 5.659343] host=192.168.11.2, domain=usen.ad.jp, nis-domain=(none) <6>[ 5.666660] bootserver=0.0.0.0, rootserver=192.168.11.5, rootpath= <6>[ 5.666665] nameserver0=192.168.11.1 <6>[ 5.682807] Freeing unused kernel memory: 2048K <6>[ 5.692668] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <4>[ 8.988217] am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator <6>[ 8.999066] am335x-phy-driver 47401300.usb-phy: Linked as a consumer to regulator.0 <4>[ 9.143021] am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator <6>[ 9.153852] am335x-phy-driver 47401b00.usb-phy: Linked as a consumer to regulator.0 <6>[ 9.259571] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.265634] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.329302] hub 1-0:1.0: USB hub found <6>[ 9.346723] hub 1-0:1.0: 1 port detected Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 64:cf:d9:3f:a0:d5 mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 192.168.11.255 IP-Config: eth0 complete (dhcp from 192.168.11.1): address: 192.168.11.2 broadcast: 192.168.11.255 netmask: 255.255.255.0 gateway: 192.168.11.1 dns0 : 192.168.11.1 dns1 : 0.0.0.0 domain : usen.ad.jp rootserver: 192.168.11.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 11.199146] systemd[1]: System time before build time, advancing clock. <3>[ 11.259994] cgroup: cgroup2: unknown option \"memory_recursiveprot\" <30>[ 11.278797] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 11.304292] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 11.344293] systemd[1]: Set hostname to . <30>[ 12.816464] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 12.827464] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 12.841110] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 12.852199] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. <30>[ 12.883387] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[0m. <30>[ 12.923332] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. <30>[ 12.963089] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. <30>[ 13.002809] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. <30>[ 13.042691] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. <30>[ 13.082553] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 13.095514] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. <30>[ 13.132736] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. <30>[ 13.162412] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. <30>[ 13.202316] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. <30>[ 13.232363] systemd[1]: Reached target Swap. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. <30>[ 13.263046] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. <30>[ 13.338072] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 13.349526] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/log)[0m. <30>[ 13.383453] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. <30>[ 13.414370] systemd[1]: Listening on Network Service Netlink Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlink Socket[0m. <30>[ 13.455226] systemd[1]: Listening on udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0m. <30>[ 13.493304] systemd[1]: Listening on udev Kernel Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. <30>[ 13.523160] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 13.532910] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 13.546595] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Debug File System[0m... <30>[ 13.586131] systemd[1]: Mounting Kernel Trace File System... Mounting [0;1;39mKernel Trace File System[0m... <30>[ 13.764356] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting [0;1;39mCreate list of st…odes for the current kernel[0m... <30>[ 13.846598] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module configfs[0m... <30>[ 13.896577] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module drm[0m... <30>[ 13.946615] systemd[1]: Starting Load Kernel Module fuse... Starting [0;1;39mLoad Kernel Module fuse[0m... <30>[ 13.996257] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 14.010759] systemd[1]: Starting Journal Service... Starting [0;1;39mJournal Service[0m... <30>[ 14.073317] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mLoad Kernel Modules[0m... <30>[ 14.116326] systemd[1]: Starting Remount Root and Kernel File Systems... Starting [0;1;39mRemount Root and Kernel File Systems[0m... <30>[ 14.186498] systemd[1]: Starting Coldplug All udev Devices... Starting [0;1;39mColdplug All udev Devices[0m... <30>[ 14.278891] systemd[1]: Mounted Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m. <30>[ 14.373742] systemd[1]: Mounted Kernel Trace File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Trace File System[0m. <30>[ 14.414858] systemd[1]: Finished Create list of static device nodes for the current kernel. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. <30>[ 14.552811] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 14.582774] systemd[1]: Finished Load Kernel Module configfs. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. <30>[ 14.615143] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 14.632569] systemd[1]: Finished Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. <30>[ 14.654699] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 14.682905] systemd[1]: Finished Load Kernel Module fuse. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. <30>[ 14.715128] systemd[1]: Finished Load Kernel Modules. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. <30>[ 14.742527] systemd[1]: Finished Remount Root and Kernel File Systems. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. <30>[ 14.768327] systemd[1]: Started Journal Service. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. Mounting [0;1;39mKernel Configuration File System[0m... Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mLoad/Save Random Seed[0m... Starting [0;1;39mApply Kernel Variables[0m... Starting [0;1;39mCreate System Users[0m... [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. <46>[ 15.263344] systemd-journald[134]: Received client request to flush runtime journal. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mNetwork Time Synchronization[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Time Synchronization[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Set[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Synchronized[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0;32m OK [0m] Found device [0;1;39m/dev/ttyO0[0m. [[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Reached target [0;1;39mHardware activated USB gadget[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [[0m[0;31m* [0m] A start job is running for Remove S…a Check Snapshots (14s / no limit) M[K[[0;1;31m*[0m[0;31m* [0m] A start job is running for Remove S…a Check Snapshots (15s / no limit) M[K[[0;31m*[0;1;31m*[0m[0;31m* [0m] A start job is running for Remove S…a Check Snapshots (15s / no limit) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] A start job is running for Remove S…a Check Snapshots (16s / no limit) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] A start job is running for Remove S…a Check Snapshots (16s / no limit) M[K[ [0;31m*[0;1;31m*[0m[0;31m*[0m] A start job is running for Remove S…a Check Snapshots (16s / no limit) M[K[ [0;31m*[0;1;31m*[0m] A start job is running for Remove S…a Check Snapshots (17s / no limit) M[K[[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [K[[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. [[0;32m OK [0m] Listening on [0;1;39mLoad/Save RF …itch Status /dev/rfkill Watch[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyO0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Runlevel Changes[0m. Debian GNU/Linu�ye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.269-cip88 #1 SMP Fri Dec 23 23:03:30 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/811639/extract-nfsrootfs-hcuwnu9g' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/811639/extract-nfsrootfs-hcuwnu9g' / # export NFS_SERVER_IP='192.168.11.5' export NFS_SERVER_IP='192.168.11.5' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-811639/environment . /lava-811639/environment / # /lava-811639/bin/lava-test-runner /lava-811639/0 /lava-811639/bin/lava-test-runner /lava-811639/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-811639/0/tests/0_timesync-off ++ cat uuid + UUID=811639_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-alsa + TESTRUN_ID=1_kselftest-alsa + cd /lava-811639/0/tests/1_kselftest-alsa ++ cat uuid + UUID=811639_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c alsa -T '' -t kselftest_armhf.tar.gz -s false -u None -L '' -S skipfile-lkft.yaml -b beaglebone-black -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-811639/0/tests/1_kselftest-alsa/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: Installing sed perl wget xz-utils iproute2 Get:1 http://deb.debian.org/debian bullseye InRelease [116 kB] Get:2 http://deb.debian.org/debian bullseye/main armhf Packages [7945 kB] Get:3 http://deb.debian.org/debian bullseye/main Translation-en [6240 kB] Fetched 14.3 MB in 28s (515 kB/s) Reading package lists... Reading package lists... Building dependency tree... Reading state information... iproute2 is already the newest version (5.10.0-4). perl is already the newest version (5.32.1-4+deb11u2). sed is already the newest version (4.7-1). wget is already the newest version (1.21-1+deb11u1). xz-utils is already the newest version (5.2.5-2.1~deb11u1). 0 upgraded, 0 newly installed, 0 to remove and 17 not upgraded. --2022-12-24 00:34:28-- http://none/ Resolving none (none)... failed: Name or service not known. wget: unable to resolve host address 'none' tar: None: Cannot open: No such file or directory tar: Error is not recoverable: exiting now ./kselftest.sh: 188: cd: can't cd to kselftest cp: cannot stat 'kselftest-list.txt': No such file or directory skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== cp: cannot stat 'kselftest-list.txt': No such file or directory cp: cannot stat 'kselftest-list.txt.original': No such file or directory grep: kselftest-list.txt: No such file or directory ============== Tests to run =============== ===========End Tests to run =============== ./kselftest.sh: 232: ./run_kselftest.sh: not found cp: cannot stat 'kselftest-list.txt.original': No such file or directory + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #