connecting to NetworkSerialPort(target=Target(name='imx6dl-riotboard-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4011, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4011 connected to 10.8.254.5 (port 4011) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2017.10.1-00009-gbc5d99d030 #1 Wed Nov 1 16:14:48 CET 2017 Board: RIoTboard i.MX6S detected i.MX6 Solo revision 1.1 mdio_bus: miibus0: probed imx-usb 2184200.usb: USB EHCI 1.00 imx-esdhc 2194000.usdhc: registered as 2194000.usdhc imx-esdhc 2198000.usdhc: registered as 2198000.usdhc imx-esdhc 219c000.usdhc: registered as 219c000.usdhc imx-ipuv3 2400000.ipu: IPUv3H probed imx-hdmi 120000.hdmi: Detected HDMI controller 0x13:0x1a:0xa0:0xc1 netconsole: registered as netconsole-1 malloc space: 0x2fefb4e0 -> 0x4fdf69bf (size 511 MiB) mmc3: detected MMC card version 4.41 mmc3: registered mmc3.boot0 mmc3: registered mmc3.boot1 mmc3: registered mmc3 running /env/bin/init... [?25h Hit m for menu or any other key to stop autoboot: 3 type exit to get to the menu [1;32mbarebox@[1;36mRIoTboard i.MX6S:/[0m bootm -v -r /mnt/tftp/867206/tftp-deploy-au_b3459/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/867206/tftp-deploy-au_b3459/dtb/imx6dl-riotboard.dtb /mnt/tftp/867206/tftp-deploy-au_b3459/kernel/zImage [1;32mbarebox@[1;36mRIoTboard i.MX6S:/[0m bootm -v -r /mnt/tftp/867206/tftp-deploy-au_b3459/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/867206/tftp-deploy-au_b3459/dtb/imx6dl-riotboard.dtb /mnt/tftp/867206/tftp-deploy-au_b3459/kernel/zImage warning: No MAC address set. Using random address 4a:86:ec:1a:4c:c9 eth0: 1000Mbps full duplex link detected T DHCP client bound to address 10.8.254.253 Loading ARM Linux zImage '/mnt/tftp/867206/tftp-deploy-au_b3459/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler no OS load address, defaulting to 0x1299b000 no initrd load address, defaulting to 0x18000000 Loaded initrd GZIP compressed '/mnt/tftp/867206/tftp-deploy-au_b3459/ramdisk/ramdisk.cpio.gz' initrd is at 0x18000000-0x18cb47ed Loading devicetree from '/mnt/tftp/867206/tftp-deploy-au_b3459/dtb/imx6dl-riotboard.dtb' mmc3: Cannot find nodepath /soc/aips-bus@02100000/usdhc@0219c000, cannot fixup Failed to fixup node in of_partition_fixup+0x1/0x1f8: Invalid argument commandline: console=ttymxc1,115200n8 Starting kernel at 0x1299b000, initrd at 0x18000000, oftree at 0x18cb5000... Starting kernel in secure mode [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.269-cip88 (KernelCI@build-j740693-arm-gcc-10-multi-v7-defconfig-vqzrt) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Dec 23 23:03:30 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: RIoTboard i.MX6S [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x4b800000 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 938440K/1048576K available (12288K kernel code, 1597K rwdata, 4676K rodata, 2048K init, 394K bss, 44600K reserved, 65536K cma-reserved, 195688K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 512 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76450001 [ 0.000000] ccm: ldb_di0_sel already changed from reset value: 0 [ 0.000000] ccm: ldb_di1_sel already changed from reset value: 0 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000025] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.002842] Console: colour dummy device 80x30 [ 0.002891] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.002907] pid_max: default: 32768 minimum: 301 [ 0.003046] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003067] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003674] CPU: Testing write buffer coherency: ok [ 0.003709] CPU0: Spectre v2: using BPIALL workaround [ 0.004059] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004731] Setting up static identity map for 0x10300000 - 0x103000a0 [ 0.006210] rcu: Hierarchical SRCU implementation. [ 0.009040] EFI services will not be available. [ 0.009201] smp: Bringing up secondary CPUs ... [ 0.009212] smp: Brought up 1 node, 1 CPU [ 0.009223] SMP: Total of 1 processors activated (6.00 BogoMIPS). [ 0.009231] CPU: All CPU(s) started in SVC mode. [ 0.010135] devtmpfs: initialized [ 0.016570] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.016936] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016957] futex hash table entries: 256 (order: 2, 16384 bytes) [ 0.019817] pinctrl core: initialized pinctrl subsystem [ 0.021362] DMI not present or invalid. [ 0.022134] NET: Registered protocol family 16 [ 0.024893] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.026852] cpuidle: using governor menu [ 0.027007] CPU identified as i.MX6DL, silicon rev 1.1 [ 0.036318] vdd1p1: supplied by regulator-dummy [ 0.036860] vdd3p0: supplied by regulator-dummy [ 0.037372] vdd2p5: supplied by regulator-dummy [ 0.037906] vddarm: supplied by regulator-dummy [ 0.038579] vddpu: supplied by regulator-dummy [ 0.038991] vddsoc: supplied by regulator-dummy [ 0.051393] No ATAGs? [ 0.051451] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.051467] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.054337] imx6dl-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory [ 0.054579] imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.058888] Serial: AMBA PL011 UART driver [ 0.083072] mxs-dma 110000.dma-apbh: initialized [ 0.088624] vgaarb: loaded [ 0.089482] SCSI subsystem initialized [ 0.089982] usbcore: registered new interface driver usbfs [ 0.090033] usbcore: registered new interface driver hub [ 0.090077] usbcore: registered new device driver usb [ 0.091485] i2c i2c-0: IMX I2C adapter registered [ 0.091504] i2c i2c-0: can't use DMA, using PIO instead. [ 0.092003] i2c i2c-1: IMX I2C adapter registered [ 0.092021] i2c i2c-1: can't use DMA, using PIO instead. [ 0.092490] i2c i2c-3: IMX I2C adapter registered [ 0.092507] i2c i2c-3: can't use DMA, using PIO instead. [ 0.093883] pps_core: LinuxPPS API ver. 1 registered [ 0.093893] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.093913] PTP clock support registered [ 0.094132] EDAC MC: Ver: 3.0.0 [ 0.096856] clocksource: Switched to clocksource mxc_timer1 [ 0.155265] NET: Registered protocol family 2 [ 0.155620] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.156557] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.156595] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.156678] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.156813] TCP: Hash tables configured (established 8192 bind 8192) [ 0.157047] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.157088] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.157250] NET: Registered protocol family 1 [ 0.157874] RPC: Registered named UNIX socket transport module. [ 0.157886] RPC: Registered udp transport module. [ 0.157895] RPC: Registered tcp transport module. [ 0.157903] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.158387] Trying to unpack rootfs image as initramfs... [ 1.264470] Freeing initrd memory: 13012K [ 1.265147] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 1.266932] Initialise system trusted keyrings [ 1.267204] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 1.273326] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.274002] NFS: Registering the id_resolver key type [ 1.274045] Key type id_resolver registered [ 1.274053] Key type id_legacy registered [ 1.274093] ntfs: driver 2.1.32 [Flags: R/O]. [ 1.276264] Key type asymmetric registered [ 1.276277] Asymmetric key parser 'x509' registered [ 1.276340] bounce: pool size: 64 pages [ 1.276389] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.276402] io scheduler noop registered [ 1.276411] io scheduler deadline registered [ 1.276566] io scheduler cfq registered (default) [ 1.276577] io scheduler mq-deadline registered [ 1.276586] io scheduler kyber registered [ 1.307796] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 1.307871] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 1.307929] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 1.308023] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 [ 1.308223] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 1.308241] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 1.308369] PU : no governor for states [ 1.308393] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 1.364520] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.368093] SuperH (H)SCI(F) driver initialized [ 1.368878] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX [ 1.369776] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 68, base_baud = 5000000) is a IMX [ 2.191563] console [ttymxc1] enabled [ 2.195882] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 69, base_baud = 5000000) is a IMX [ 2.205156] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 70, base_baud = 5000000) is a IMX [ 2.214414] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 71, base_baud = 5000000) is a IMX [ 2.224218] msm_serial: driver initialized [ 2.228606] STMicroelectronics ASC driver initialized [ 2.234871] STM32 USART driver initialized [ 2.256606] brd: module loaded [ 2.268051] loop: module loaded [ 2.283645] CAN device driver interface [ 2.288707] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.295876] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 2.304595] fec 2188000.ethernet: Linked as a consumer to regulator.0 [ 2.313512] pps pps0: new PPS source ptp0 [ 2.343617] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.350751] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.356590] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.362618] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.369602] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.380434] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.387914] usbcore: registered new interface driver pegasus [ 2.393625] usbcore: registered new interface driver asix [ 2.399086] usbcore: registered new interface driver ax88179_178a [ 2.405212] usbcore: registered new interface driver cdc_ether [ 2.411112] usbcore: registered new interface driver smsc75xx [ 2.416919] usbcore: registered new interface driver smsc95xx [ 2.422698] usbcore: registered new interface driver net1080 [ 2.428419] usbcore: registered new interface driver cdc_subset [ 2.434373] usbcore: registered new interface driver zaurus [ 2.440040] usbcore: registered new interface driver cdc_ncm [ 2.448414] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.454948] ehci-pci: EHCI PCI platform driver [ 2.459471] ehci-platform: EHCI generic platform driver [ 2.464958] ehci-orion: EHCI orion driver [ 2.469195] SPEAr-ehci: EHCI SPEAr driver [ 2.473378] ehci-st: EHCI STMicroelectronics driver [ 2.478452] ehci-exynos: EHCI EXYNOS driver [ 2.482800] ehci-atmel: EHCI Atmel driver [ 2.486998] tegra-ehci: Tegra EHCI driver [ 2.491204] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.497426] ohci-pci: OHCI PCI platform driver [ 2.501918] ohci-platform: OHCI generic platform driver [ 2.507399] SPEAr-ohci: OHCI SPEAr driver [ 2.511589] ohci-st: OHCI STMicroelectronics driver [ 2.516641] ohci-atmel: OHCI Atmel driver [ 2.521603] usbcore: registered new interface driver usb-storage [ 2.529828] imx_usb 2184000.usb: Linked as a consumer to regulator.9 [ 2.541665] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator [ 2.549980] imx_usb 2184200.usb: Linked as a consumer to regulator.0 [ 2.559900] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.564810] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 2.596863] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.602984] hub 1-0:1.0: USB hub found [ 2.606779] hub 1-0:1.0: 1 port detected [ 2.616579] i2c /dev entries driver [ 2.633479] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 2.644268] sdhci: Secure Digital Host Controller Interface driver [ 2.650496] sdhci: Copyright(c) Pierre Ossman [ 2.656910] Synopsys Designware Multimedia Card Interface Driver [ 2.664708] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.671326] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO [ 2.676496] sdhci-esdhc-imx 2194000.usdhc: Got WP GPIO [ 2.681781] sdhci-esdhc-imx 2194000.usdhc: Linked as a consumer to regulator.8 [ 2.721469] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 2.729399] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 2.734575] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 2.739847] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 [ 2.779556] mmc1: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 2.787481] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 [ 2.826894] mmc2: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.838429] ledtrig-cpu: registered to indicate activity on CPUs [ 2.845310] usbcore: registered new interface driver usbhid [ 2.850936] usbhid: USB HID core driver [ 2.860515] NET: Registered protocol family 10 [ 2.866205] Segment Routing with IPv6 [ 2.870002] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.876495] NET: Registered protocol family 17 [ 2.881001] can: controller area network core (rev 20170425 abi 9) [ 2.887278] NET: Registered protocol family 29 [ 2.891730] can: raw protocol (rev 20170425) [ 2.896006] can: broadcast manager protocol (rev 20170425 t) [ 2.901694] can: netlink gateway (rev 20170425) max_hops=1 [ 2.907642] Key type dns_resolver registered [ 2.912789] cpu cpu0: Linked as a consumer to regulator.4 [ 2.918311] cpu cpu0: Linked as a consumer to regulator.5 [ 2.923766] cpu cpu0: Linked as a consumer to regulator.6 [ 2.929913] ThumbEE CPU extension supported. [ 2.934198] Registering SWP/SWPB emulation handler [ 2.940784] Loading compiled-in X.509 certificates [ 2.965988] imx_thermal tempmon: Commercial CPU temperature grade - max:95C critical:90C passive:85C [ 2.976220] hctosys: unable to open rtc device (rtc0) [ 2.986086] Freeing unused kernel memory: 2048K [ 2.991027] Run /init as init process [ 3.009635] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.044145] mmc2: new DDR MMC card at address 0001 [ 3.053579] mmcblk2: mmc2:0001 MMC04G 3.58 GiB [ 3.059485] mmcblk2boot0: mmc2:0001 MMC04G partition 1 2.00 MiB [ 3.066736] mmcblk2boot1: mmc2:0001 MMC04G partition 2 2.00 MiB [ 3.087060] mmcblk2rpmb: mmc2:0001 MMC04G partition 3 128 KiB, chardev (235:0) Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 3.184614] udevd[86]: starting version 3.2.9 [ 3.190076] random: udevd: uninitialized urandom read (16 bytes read) [ 3.196738] random: udevd: uninitialized urandom read (16 bytes read) [ 3.203765] random: udevd: uninitialized urandom read (16 bytes read) [ 3.218400] hub 1-1:1.0: USB hub found [ 3.222572] udevd[86]: specified user 'tss' unknown [ 3.227763] hub 1-1:1.0: 4 ports detected [ 3.231993] udevd[86]: specified group 'tss' unknown [ 3.241133] udevd[87]: starting eudev-3.2.9 [ 4.078394] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 4.137075] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 4.143532] etnaviv-gpu 130000.gpu: model: GC880, revision: 5106 [ 4.294021] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 4.453609] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 [ 4.471709] sgtl5000 0-000a: Linked as a consumer to regulator.7 [ 4.477858] sgtl5000 0-000a: Linked as a consumer to regulator.8 [ 4.560105] sgtl5000 0-000a: Error reading chip id -6 [ 4.565218] sgtl5000 0-000a: Dropping the link to regulator.7 [ 4.602820] sgtl5000 0-000a: Dropping the link to regulator.8 done Saving random seed: [ 5.139945] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: [ 5.221687] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-867206/environment . /lava-867206/environment / # /lava-867206/bin/lava-test-runner /lava-867206/0 /lava-867206/bin/lava-test-runner /lava-867206/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-867206/0/tests/0_dmes[ 5.795972] g + cat uuid + UUID=867206_1.5.2.3.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 5.835385] [ 5.872671] [ 5.909996] + set +x [ 5.919790] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-867206/environment / # . /lava-867206/environment/lava-867206/bin/lava-test-runner /lava-867206/1 / # /lava-867206/bin/lava-test-runner /lava-867206/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-867206/1/tests/1_boot[ 6.406155] rr + cat uuid + UUID=867206_1.5[ 6.413147] .2.3.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-867206/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr /lava-867206/1/tests/1_bootrr/run.sh: cd: line 15: can't cd to /opt/bootrr/libexec/bootrr: No such file or directory + set +x / #